PCI_DEV_REG5 = 0x88,
PCI_CFG_REG_0 = 0x90,
PCI_CFG_REG_1 = 0x94,
-};
-enum {
- PEX_DEV_CAP = 0xe4,
- PEX_DEV_CTRL = 0xe8,
- PEX_DEV_STA = 0xea,
- PEX_LNK_STAT = 0xf2,
- PEX_UNC_ERR_STAT= 0x104,
+ PSM_CONFIG_REG0 = 0x98,
+ PSM_CONFIG_REG1 = 0x9C,
+ PSM_CONFIG_REG2 = 0x160,
+ PSM_CONFIG_REG3 = 0x164,
+ PSM_CONFIG_REG4 = 0x168,
+
};
/* Yukon-2 */
PCI_Y2_PHY2_POWD = 1<<27, /* Set PHY 2 to Power Down (YUKON-2) */
PCI_Y2_PHY1_POWD = 1<<26, /* Set PHY 1 to Power Down (YUKON-2) */
PCI_Y2_PME_LEGACY= 1<<15, /* PCI Express legacy power management mode */
+
+ PCI_PHY_LNK_TIM_MSK= 3L<<8,/* Bit 9.. 8: GPHY Link Trigger Timer */
+ PCI_ENA_L1_EVENT = 1<<7, /* Enable PEX L1 Event */
+ PCI_ENA_GPHY_LNK = 1<<6, /* Enable PEX L1 on GPHY Link down */
+ PCI_FORCE_PEX_L1 = 1<<5, /* Force to PEX L1 */
};
enum pci_dev_reg_2 {
PCI_USEDATA64 = 1<<0, /* Use 64Bit Data bus ext */
};
+/* PCI_OUR_REG_3 32 bit Our Register 3 (Yukon-ECU only) */
+enum pci_dev_reg_3 {
+ P_CLK_ASF_REGS_DIS = 1<<18,/* Disable Clock ASF (Yukon-Ext.) */
+ P_CLK_COR_REGS_D0_DIS = 1<<17,/* Disable Clock Core Regs D0 */
+ P_CLK_MACSEC_DIS = 1<<17,/* Disable Clock MACSec (Yukon-Ext.) */
+ P_CLK_PCI_REGS_D0_DIS = 1<<16,/* Disable Clock PCI Regs D0 */
+ P_CLK_COR_YTB_ARB_DIS = 1<<15,/* Disable Clock YTB Arbiter */
+ P_CLK_MAC_LNK1_D3_DIS = 1<<14,/* Disable Clock MAC Link1 D3 */
+ P_CLK_COR_LNK1_D0_DIS = 1<<13,/* Disable Clock Core Link1 D0 */
+ P_CLK_MAC_LNK1_D0_DIS = 1<<12,/* Disable Clock MAC Link1 D0 */
+ P_CLK_COR_LNK1_D3_DIS = 1<<11,/* Disable Clock Core Link1 D3 */
+ P_CLK_PCI_MST_ARB_DIS = 1<<10,/* Disable Clock PCI Master Arb. */
+ P_CLK_COR_REGS_D3_DIS = 1<<9, /* Disable Clock Core Regs D3 */
+ P_CLK_PCI_REGS_D3_DIS = 1<<8, /* Disable Clock PCI Regs D3 */
+ P_CLK_REF_LNK1_GM_DIS = 1<<7, /* Disable Clock Ref. Link1 GMAC */
+ P_CLK_COR_LNK1_GM_DIS = 1<<6, /* Disable Clock Core Link1 GMAC */
+ P_CLK_PCI_COMMON_DIS = 1<<5, /* Disable Clock PCI Common */
+ P_CLK_COR_COMMON_DIS = 1<<4, /* Disable Clock Core Common */
+ P_CLK_PCI_LNK1_BMU_DIS = 1<<3, /* Disable Clock PCI Link1 BMU */
+ P_CLK_COR_LNK1_BMU_DIS = 1<<2, /* Disable Clock Core Link1 BMU */
+ P_CLK_PCI_LNK1_BIU_DIS = 1<<1, /* Disable Clock PCI Link1 BIU */
+ P_CLK_COR_LNK1_BIU_DIS = 1<<0, /* Disable Clock Core Link1 BIU */
+ PCIE_OUR3_WOL_D3_COLD_SET = P_CLK_ASF_REGS_DIS |
+ P_CLK_COR_REGS_D0_DIS |
+ P_CLK_COR_LNK1_D0_DIS |
+ P_CLK_MAC_LNK1_D0_DIS |
+ P_CLK_PCI_MST_ARB_DIS |
+ P_CLK_COR_COMMON_DIS |
+ P_CLK_COR_LNK1_BMU_DIS,
+};
+
/* PCI_OUR_REG_4 32 bit Our Register 4 (Yukon-ECU only) */
enum pci_dev_reg_4 {
- /* (Link Training & Status State Machine) */
+ /* (Link Training & Status State Machine) */
+ P_PEX_LTSSM_STAT_MSK = 0x7fL<<25, /* Bit 31..25: PEX LTSSM Mask */
+#define P_PEX_LTSSM_STAT(x) ((x << 25) & P_PEX_LTSSM_STAT_MSK)
+ P_PEX_LTSSM_L1_STAT = 0x34,
+ P_PEX_LTSSM_DET_STAT = 0x01,
P_TIMER_VALUE_MSK = 0xffL<<16, /* Bit 23..16: Timer Value Mask */
/* (Active State Power Management) */
P_FORCE_ASPM_REQUEST = 1<<15, /* Force ASPM Request (A1 only) */
P_GAT_PCIE_RX_EL_IDLE,
};
-#/* PCI_CFG_REG_1 32 bit Config Register 1 (Yukon-Ext only) */
+/* PCI_CFG_REG_1 32 bit Config Register 1 (Yukon-Ext only) */
enum pci_cfg_reg1 {
P_CF1_DIS_REL_EVT_RST = 1<<24, /* Dis. Rel. Event during PCIE reset */
/* Bit 23..21: Release Clock on Event */
P_CF1_ENA_TXBMU_WR_IDLE,
};
+/* Yukon-Optima */
+enum {
+ PSM_CONFIG_REG1_AC_PRESENT_STATUS = 1<<31, /* AC Present Status */
-#define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \
- PCI_STATUS_SIG_SYSTEM_ERROR | \
- PCI_STATUS_REC_MASTER_ABORT | \
- PCI_STATUS_REC_TARGET_ABORT | \
- PCI_STATUS_PARITY)
+ PSM_CONFIG_REG1_PTP_CLK_SEL = 1<<29, /* PTP Clock Select */
+ PSM_CONFIG_REG1_PTP_MODE = 1<<28, /* PTP Mode */
+
+ PSM_CONFIG_REG1_MUX_PHY_LINK = 1<<27, /* PHY Energy Detect Event */
+
+ PSM_CONFIG_REG1_EN_PIN63_AC_PRESENT = 1<<26, /* Enable LED_DUPLEX for ac_present */
+ PSM_CONFIG_REG1_EN_PCIE_TIMER = 1<<25, /* Enable PCIe Timer */
+ PSM_CONFIG_REG1_EN_SPU_TIMER = 1<<24, /* Enable SPU Timer */
+ PSM_CONFIG_REG1_POLARITY_AC_PRESENT = 1<<23, /* AC Present Polarity */
-enum pex_dev_ctrl {
- PEX_DC_MAX_RRS_MSK = 7<<12, /* Bit 14..12: Max. Read Request Size */
- PEX_DC_EN_NO_SNOOP = 1<<11,/* Enable No Snoop */
- PEX_DC_EN_AUX_POW = 1<<10,/* Enable AUX Power */
- PEX_DC_EN_PHANTOM = 1<<9, /* Enable Phantom Functions */
- PEX_DC_EN_EXT_TAG = 1<<8, /* Enable Extended Tag Field */
- PEX_DC_MAX_PLS_MSK = 7<<5, /* Bit 7.. 5: Max. Payload Size Mask */
- PEX_DC_EN_REL_ORD = 1<<4, /* Enable Relaxed Ordering */
- PEX_DC_EN_UNS_RQ_RP = 1<<3, /* Enable Unsupported Request Reporting */
- PEX_DC_EN_FAT_ER_RP = 1<<2, /* Enable Fatal Error Reporting */
- PEX_DC_EN_NFA_ER_RP = 1<<1, /* Enable Non-Fatal Error Reporting */
- PEX_DC_EN_COR_ER_RP = 1<<0, /* Enable Correctable Error Reporting */
+ PSM_CONFIG_REG1_EN_AC_PRESENT = 1<<21, /* Enable AC Present */
+
+ PSM_CONFIG_REG1_EN_GPHY_INT_PSM = 1<<20, /* Enable GPHY INT for PSM */
+ PSM_CONFIG_REG1_DIS_PSM_TIMER = 1<<19, /* Disable PSM Timer */
};
-#define PEX_DC_MAX_RD_RQ_SIZE(x) (((x)<<12) & PEX_DC_MAX_RRS_MSK)
-/* PEX_UNC_ERR_STAT PEX Uncorrectable Errors Status Register (Yukon-2) */
-enum pex_err {
- PEX_UNSUP_REQ = 1<<20, /* Unsupported Request Error */
+/* Yukon-Supreme */
+enum {
+ PSM_CONFIG_REG1_GPHY_ENERGY_STS = 1<<31, /* GPHY Energy Detect Status */
- PEX_MALFOR_TLP = 1<<18, /* Malformed TLP */
+ PSM_CONFIG_REG1_UART_MODE_MSK = 3<<29, /* UART_Mode */
+ PSM_CONFIG_REG1_CLK_RUN_ASF = 1<<28, /* Enable Clock Free Running for ASF Subsystem */
+ PSM_CONFIG_REG1_UART_CLK_DISABLE= 1<<27, /* Disable UART clock */
+ PSM_CONFIG_REG1_VAUX_ONE = 1<<26, /* Tie internal Vaux to 1'b1 */
+ PSM_CONFIG_REG1_UART_FC_RI_VAL = 1<<25, /* Default value for UART_RI_n */
+ PSM_CONFIG_REG1_UART_FC_DCD_VAL = 1<<24, /* Default value for UART_DCD_n */
+ PSM_CONFIG_REG1_UART_FC_DSR_VAL = 1<<23, /* Default value for UART_DSR_n */
+ PSM_CONFIG_REG1_UART_FC_CTS_VAL = 1<<22, /* Default value for UART_CTS_n */
+ PSM_CONFIG_REG1_LATCH_VAUX = 1<<21, /* Enable Latch current Vaux_avlbl */
+ PSM_CONFIG_REG1_FORCE_TESTMODE_INPUT= 1<<20, /* Force Testmode pin as input PAD */
+ PSM_CONFIG_REG1_UART_RST = 1<<19, /* UART_RST */
+ PSM_CONFIG_REG1_PSM_PCIE_L1_POL = 1<<18, /* PCIE L1 Event Polarity for PSM */
+ PSM_CONFIG_REG1_TIMER_STAT = 1<<17, /* PSM Timer Status */
+ PSM_CONFIG_REG1_GPHY_INT = 1<<16, /* GPHY INT Status */
+ PSM_CONFIG_REG1_FORCE_TESTMODE_ZERO= 1<<15, /* Force internal Testmode as 1'b0 */
+ PSM_CONFIG_REG1_EN_INT_ASPM_CLKREQ = 1<<14, /* ENABLE INT for CLKRUN on ASPM and CLKREQ */
+ PSM_CONFIG_REG1_EN_SND_TASK_ASPM_CLKREQ = 1<<13, /* ENABLE Snd_task for CLKRUN on ASPM and CLKREQ */
+ PSM_CONFIG_REG1_DIS_CLK_GATE_SND_TASK = 1<<12, /* Disable CLK_GATE control snd_task */
+ PSM_CONFIG_REG1_DIS_FF_CHIAN_SND_INTA = 1<<11, /* Disable flip-flop chain for sndmsg_inta */
- PEX_UNEXP_COMP = 1<<16, /* Unexpected Completion */
+ PSM_CONFIG_REG1_DIS_LOADER = 1<<9, /* Disable Loader SM after PSM Goes back to IDLE */
+ PSM_CONFIG_REG1_DO_PWDN = 1<<8, /* Do Power Down, Start PSM Scheme */
+ PSM_CONFIG_REG1_DIS_PIG = 1<<7, /* Disable Plug-in-Go SM after PSM Goes back to IDLE */
+ PSM_CONFIG_REG1_DIS_PERST = 1<<6, /* Disable Internal PCIe Reset after PSM Goes back to IDLE */
+ PSM_CONFIG_REG1_EN_REG18_PD = 1<<5, /* Enable REG18 Power Down for PSM */
+ PSM_CONFIG_REG1_EN_PSM_LOAD = 1<<4, /* Disable EEPROM Loader after PSM Goes back to IDLE */
+ PSM_CONFIG_REG1_EN_PSM_HOT_RST = 1<<3, /* Enable PCIe Hot Reset for PSM */
+ PSM_CONFIG_REG1_EN_PSM_PERST = 1<<2, /* Enable PCIe Reset Event for PSM */
+ PSM_CONFIG_REG1_EN_PSM_PCIE_L1 = 1<<1, /* Enable PCIe L1 Event for PSM */
+ PSM_CONFIG_REG1_EN_PSM = 1<<0, /* Enable PSM Scheme */
+};
- PEX_COMP_TO = 1<<14, /* Completion Timeout */
- PEX_FLOW_CTRL_P = 1<<13, /* Flow Control Protocol Error */
- PEX_POIS_TLP = 1<<12, /* Poisoned TLP */
+/* PSM_CONFIG_REG4 0x0168 PSM Config Register 4 */
+enum {
+ /* PHY Link Detect Timer */
+ PSM_CONFIG_REG4_TIMER_PHY_LINK_DETECT_MSK = 0xf<<4,
+ PSM_CONFIG_REG4_TIMER_PHY_LINK_DETECT_BASE = 4,
- PEX_DATA_LINK_P = 1<<4, /* Data Link Protocol Error */
- PEX_FATAL_ERRORS= (PEX_MALFOR_TLP | PEX_FLOW_CTRL_P | PEX_DATA_LINK_P),
+ PSM_CONFIG_REG4_DEBUG_TIMER = 1<<1, /* Debug Timer */
+ PSM_CONFIG_REG4_RST_PHY_LINK_DETECT = 1<<0, /* Reset GPHY Link Detect */
};
+#define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \
+ PCI_STATUS_SIG_SYSTEM_ERROR | \
+ PCI_STATUS_REC_MASTER_ABORT | \
+ PCI_STATUS_REC_TARGET_ABORT | \
+ PCI_STATUS_PARITY)
+
enum csr_regs {
B0_RAP = 0x0000,
B0_CTST = 0x0004,
- B0_Y2LED = 0x0005,
+
B0_POWER_CTRL = 0x0007,
B0_ISRC = 0x0008,
B0_IMSK = 0x000c,
B2_I2C_IRQ = 0x0168,
B2_I2C_SW = 0x016c,
+ Y2_PEX_PHY_DATA = 0x0170,
+ Y2_PEX_PHY_ADDR = 0x0172,
+
B3_RAM_ADDR = 0x0180,
B3_RAM_DATA_LO = 0x0184,
B3_RAM_DATA_HI = 0x0188,
B3_PA_CTRL = 0x01f0,
B3_PA_TEST = 0x01f2,
- Y2_CFG_SPC = 0x1c00,
+ Y2_CFG_SPC = 0x1c00, /* PCI config space region */
+ Y2_CFG_AER = 0x1d00, /* PCI Advanced Error Report region */
};
-/* B0_CTST 16 bit Control/Status register */
+/* B0_CTST 24 bit Control/Status register */
enum {
Y2_VMAIN_AVAIL = 1<<17,/* VMAIN available (YUKON-2 only) */
Y2_VAUX_AVAIL = 1<<16,/* VAUX available (YUKON-2 only) */
CS_RST_SET = 1, /* Set Software reset */
};
-/* B0_LED 8 Bit LED register */
-enum {
-/* Bit 7.. 2: reserved */
- LED_STAT_ON = 1<<1, /* Status LED on */
- LED_STAT_OFF = 1, /* Status LED off */
-};
-
/* B0_POWER_CTRL 8 Bit Power Control reg (YUKON only) */
enum {
PC_VAUX_ENA = 1<<7, /* Switch VAUX Enable */
Y2_IS_CHK_TXS2 = 1<<9, /* Descriptor error TXS 2 */
Y2_IS_CHK_TXA2 = 1<<8, /* Descriptor error TXA 2 */
+ Y2_IS_PSM_ACK = 1<<7, /* PSM Acknowledge (Yukon-Optima only) */
+ Y2_IS_PTP_TIST = 1<<6, /* PTP Time Stamp (Yukon-Optima only) */
+ Y2_IS_PHY_QLNK = 1<<5, /* PHY Quick Link (Yukon-Optima only) */
+
Y2_IS_IRQ_PHY1 = 1<<4, /* Interrupt from PHY 1 */
Y2_IS_IRQ_MAC1 = 1<<3, /* Interrupt from MAC 1 */
Y2_IS_CHK_RX1 = 1<<2, /* Descriptor error Rx 1 */
Y2_IS_PAR_RX2 | Y2_IS_TCP_TXS2| Y2_IS_TCP_TXA2,
Y2_HWE_ALL_MASK = Y2_IS_TIST_OV | Y2_IS_MST_ERR | Y2_IS_IRQ_STAT |
- Y2_IS_PCI_EXP |
Y2_HWE_L1_MASK | Y2_HWE_L2_MASK,
};
/* B2_CHIP_ID 8 bit Chip Identification Number */
enum {
- CHIP_ID_YUKON_XL = 0xb3, /* Chip ID for YUKON-2 XL */
- CHIP_ID_YUKON_EC_U = 0xb4, /* Chip ID for YUKON-2 EC Ultra */
- CHIP_ID_YUKON_EX = 0xb5, /* Chip ID for YUKON-2 Extreme */
- CHIP_ID_YUKON_EC = 0xb6, /* Chip ID for YUKON-2 EC */
- CHIP_ID_YUKON_FE = 0xb7, /* Chip ID for YUKON-2 FE */
+ CHIP_ID_YUKON_XL = 0xb3, /* YUKON-2 XL */
+ CHIP_ID_YUKON_EC_U = 0xb4, /* YUKON-2 EC Ultra */
+ CHIP_ID_YUKON_EX = 0xb5, /* YUKON-2 Extreme */
+ CHIP_ID_YUKON_EC = 0xb6, /* YUKON-2 EC */
+ CHIP_ID_YUKON_FE = 0xb7, /* YUKON-2 FE */
+ CHIP_ID_YUKON_FE_P = 0xb8, /* YUKON-2 FE+ */
+ CHIP_ID_YUKON_SUPR = 0xb9, /* YUKON-2 Supreme */
+ CHIP_ID_YUKON_UL_2 = 0xba, /* YUKON-2 Ultra 2 */
+ CHIP_ID_YUKON_OPT = 0xbc, /* YUKON-2 Optima */
+};
+
+enum yukon_xl_rev {
+ CHIP_REV_YU_XL_A0 = 0,
+ CHIP_REV_YU_XL_A1 = 1,
+ CHIP_REV_YU_XL_A2 = 2,
+ CHIP_REV_YU_XL_A3 = 3,
+};
+enum yukon_ec_rev {
CHIP_REV_YU_EC_A1 = 0, /* Chip Rev. for Yukon-EC A1/A0 */
CHIP_REV_YU_EC_A2 = 1, /* Chip Rev. for Yukon-EC A2 */
CHIP_REV_YU_EC_A3 = 2, /* Chip Rev. for Yukon-EC A3 */
-
+};
+enum yukon_ec_u_rev {
CHIP_REV_YU_EC_U_A0 = 1,
CHIP_REV_YU_EC_U_A1 = 2,
CHIP_REV_YU_EC_U_B0 = 3,
-
+ CHIP_REV_YU_EC_U_B1 = 5,
+};
+enum yukon_fe_rev {
CHIP_REV_YU_FE_A1 = 1,
CHIP_REV_YU_FE_A2 = 2,
-
+};
+enum yukon_fe_p_rev {
+ CHIP_REV_YU_FE2_A0 = 0,
+};
+enum yukon_ex_rev {
+ CHIP_REV_YU_EX_A0 = 1,
+ CHIP_REV_YU_EX_B0 = 2,
+};
+enum yukon_supr_rev {
+ CHIP_REV_YU_SU_A0 = 0,
+ CHIP_REV_YU_SU_B0 = 1,
+ CHIP_REV_YU_SU_B1 = 3,
};
+
/* B2_Y2_CLK_GATE 8 bit Clock Gating (Yukon-2 only) */
enum {
Y2_STATUS_LNK2_INAC = 1<<7, /* Status Link 2 inactive (0 = active) */
TIM_T_STEP = 1<<0, /* Test step */
};
+/* Y2_PEX_PHY_ADDR/DATA PEX PHY address and data reg (Yukon-2 only) */
+enum {
+ PEX_RD_ACCESS = 1<<31, /* Access Mode Read = 1, Write = 0 */
+ PEX_DB_ACCESS = 1<<30, /* Access to debug register */
+};
+
/* B3_RAM_ADDR 32 bit RAM Address, to read or write */
/* Bit 31..19: reserved */
#define RAM_ADR_RAN 0x0007ffffL /* Bit 18.. 0: RAM Address Range */
TXA_CTRL = 0x0210,/* 8 bit Tx Arbiter Control Register */
TXA_TEST = 0x0211,/* 8 bit Tx Arbiter Test Register */
TXA_STAT = 0x0212,/* 8 bit Tx Arbiter Status Register */
+
+ RSS_KEY = 0x0220, /* RSS Key setup */
+ RSS_CFG = 0x0248, /* RSS Configuration */
};
+enum {
+ HASH_TCP_IPV6_EX_CTRL = 1<<5,
+ HASH_IPV6_EX_CTRL = 1<<4,
+ HASH_TCP_IPV6_CTRL = 1<<3,
+ HASH_IPV6_CTRL = 1<<2,
+ HASH_TCP_IPV4_CTRL = 1<<1,
+ HASH_IPV4_CTRL = 1<<0,
+
+ HASH_ALL = 0x3f,
+};
enum {
B6_EXT_REG = 0x0300,/* External registers (GENESIS only) */
RX_GMF_AF_THR = 0x0c44,/* 32 bit Rx GMAC FIFO Almost Full Thresh. */
RX_GMF_CTRL_T = 0x0c48,/* 32 bit Rx GMAC FIFO Control/Test */
RX_GMF_FL_MSK = 0x0c4c,/* 32 bit Rx GMAC FIFO Flush Mask */
- RX_GMF_FL_THR = 0x0c50,/* 32 bit Rx GMAC FIFO Flush Threshold */
+ RX_GMF_FL_THR = 0x0c50,/* 16 bit Rx GMAC FIFO Flush Threshold */
+ RX_GMF_FL_CTRL = 0x0c52,/* 16 bit Rx GMAC FIFO Flush Control */
RX_GMF_TR_THR = 0x0c54,/* 32 bit Rx Truncation Threshold (Yukon-2) */
- RX_GMF_UP_THR = 0x0c58,/* 8 bit Rx Upper Pause Thr (Yukon-EC_U) */
- RX_GMF_LP_THR = 0x0c5a,/* 8 bit Rx Lower Pause Thr (Yukon-EC_U) */
+ RX_GMF_UP_THR = 0x0c58,/* 16 bit Rx Upper Pause Thr (Yukon-EC_U) */
+ RX_GMF_LP_THR = 0x0c5a,/* 16 bit Rx Lower Pause Thr (Yukon-EC_U) */
RX_GMF_VLAN = 0x0c5c,/* 32 bit Rx VLAN Type Register (Yukon-2) */
RX_GMF_WP = 0x0c60,/* 32 bit Rx GMAC FIFO Write Pointer */
BMU_TX_CLR_IRQ_TCP = 1<<11, /* Clear IRQ on TCP segment length mismatch */
};
+/* TBMU_TEST 0x06B8 Transmit BMU Test Register */
+enum {
+ TBMU_TEST_BMU_TX_CHK_AUTO_OFF = 1<<31, /* BMU Tx Checksum Auto Calculation Disable */
+ TBMU_TEST_BMU_TX_CHK_AUTO_ON = 1<<30, /* BMU Tx Checksum Auto Calculation Enable */
+ TBMU_TEST_HOME_ADD_PAD_FIX1_EN = 1<<29, /* Home Address Paddiing FIX1 Enable */
+ TBMU_TEST_HOME_ADD_PAD_FIX1_DIS = 1<<28, /* Home Address Paddiing FIX1 Disable */
+ TBMU_TEST_ROUTING_ADD_FIX_EN = 1<<27, /* Routing Address Fix Enable */
+ TBMU_TEST_ROUTING_ADD_FIX_DIS = 1<<26, /* Routing Address Fix Disable */
+ TBMU_TEST_HOME_ADD_FIX_EN = 1<<25, /* Home address checksum fix enable */
+ TBMU_TEST_HOME_ADD_FIX_DIS = 1<<24, /* Home address checksum fix disable */
+
+ TBMU_TEST_TEST_RSPTR_ON = 1<<22, /* Testmode Shadow Read Ptr On */
+ TBMU_TEST_TEST_RSPTR_OFF = 1<<21, /* Testmode Shadow Read Ptr Off */
+ TBMU_TEST_TESTSTEP_RSPTR = 1<<20, /* Teststep Shadow Read Ptr */
+
+ TBMU_TEST_TEST_RPTR_ON = 1<<18, /* Testmode Read Ptr On */
+ TBMU_TEST_TEST_RPTR_OFF = 1<<17, /* Testmode Read Ptr Off */
+ TBMU_TEST_TESTSTEP_RPTR = 1<<16, /* Teststep Read Ptr */
+
+ TBMU_TEST_TEST_WSPTR_ON = 1<<14, /* Testmode Shadow Write Ptr On */
+ TBMU_TEST_TEST_WSPTR_OFF = 1<<13, /* Testmode Shadow Write Ptr Off */
+ TBMU_TEST_TESTSTEP_WSPTR = 1<<12, /* Teststep Shadow Write Ptr */
+
+ TBMU_TEST_TEST_WPTR_ON = 1<<10, /* Testmode Write Ptr On */
+ TBMU_TEST_TEST_WPTR_OFF = 1<<9, /* Testmode Write Ptr Off */
+ TBMU_TEST_TESTSTEP_WPTR = 1<<8, /* Teststep Write Ptr */
+
+ TBMU_TEST_TEST_REQ_NB_ON = 1<<6, /* Testmode Req Nbytes/Addr On */
+ TBMU_TEST_TEST_REQ_NB_OFF = 1<<5, /* Testmode Req Nbytes/Addr Off */
+ TBMU_TEST_TESTSTEP_REQ_NB = 1<<4, /* Teststep Req Nbytes/Addr */
+
+ TBMU_TEST_TEST_DONE_IDX_ON = 1<<2, /* Testmode Done Index On */
+ TBMU_TEST_TEST_DONE_IDX_OFF = 1<<1, /* Testmode Done Index Off */
+ TBMU_TEST_TESTSTEP_DONE_IDX = 1<<0, /* Teststep Done Index */
+};
+
/* Queue Prefetch Unit Offsets, use Y2_QADDR() to address (Yukon-2 only)*/
/* PREF_UNIT_CTRL 32 bit Prefetch Control register */
enum {
PHY_M_PC_ENA_AUTO = 3, /* 11 = Enable Automatic Crossover */
};
+/* for Yukon-EC Ultra Gigabit Ethernet PHY (88E1149 only) */
+enum {
+ PHY_M_PC_COP_TX_DIS = 1<<3, /* Copper Transmitter Disable */
+ PHY_M_PC_POW_D_ENA = 1<<2, /* Power Down Enable */
+};
+
/* for 10/100 Fast Ethernet PHY (88E3082 only) */
enum {
PHY_M_PC_ENA_DTE_DT = 1<<15, /* Enable Data Terminal Equ. (DTE) Detect */
BLINK_670MS = 4,/* 670 ms */
};
-/**** PHY_MARV_LED_OVER 16 bit r/w LED control */
-enum {
- PHY_M_LED_MO_DUP = 3<<10,/* Bit 11..10: Duplex */
- PHY_M_LED_MO_10 = 3<<8, /* Bit 9.. 8: Link 10 */
- PHY_M_LED_MO_100 = 3<<6, /* Bit 7.. 6: Link 100 */
- PHY_M_LED_MO_1000 = 3<<4, /* Bit 5.. 4: Link 1000 */
- PHY_M_LED_MO_RX = 3<<2, /* Bit 3.. 2: Rx */
- PHY_M_LED_MO_TX = 3<<0, /* Bit 1.. 0: Tx */
+/***** PHY_MARV_LED_OVER 16 bit r/w Manual LED Override Reg *****/
+#define PHY_M_LED_MO_SGMII(x) ((x)<<14) /* Bit 15..14: SGMII AN Timer */
+
+#define PHY_M_LED_MO_DUP(x) ((x)<<10) /* Bit 11..10: Duplex */
+#define PHY_M_LED_MO_10(x) ((x)<<8) /* Bit 9.. 8: Link 10 */
+#define PHY_M_LED_MO_100(x) ((x)<<6) /* Bit 7.. 6: Link 100 */
+#define PHY_M_LED_MO_1000(x) ((x)<<4) /* Bit 5.. 4: Link 1000 */
+#define PHY_M_LED_MO_RX(x) ((x)<<2) /* Bit 3.. 2: Rx */
+#define PHY_M_LED_MO_TX(x) ((x)<<0) /* Bit 1.. 0: Tx */
- PHY_M_LED_ALL = PHY_M_LED_MO_DUP | PHY_M_LED_MO_10
- | PHY_M_LED_MO_100 | PHY_M_LED_MO_1000
- | PHY_M_LED_MO_RX,
+enum led_mode {
+ MO_LED_NORM = 0,
+ MO_LED_BLINK = 1,
+ MO_LED_OFF = 2,
+ MO_LED_ON = 3,
};
/***** PHY_MARV_EXT_CTRL_2 16 bit r/w Ext. PHY Specific Ctrl 2 *****/
/***** PHY_MARV_PHY_CTRL (page 2) 16 bit r/w MAC Specific Ctrl *****/
enum {
PHY_M_MAC_MD_MSK = 7<<7, /* Bit 9.. 7: Mode Select Mask */
+ PHY_M_MAC_GMIF_PUP = 1<<3, /* GMII Power Up (88E1149 only) */
PHY_M_MAC_MD_AUTO = 3,/* Auto Copper/1000Base-X */
PHY_M_MAC_MD_COPPER = 5,/* Copper only */
PHY_M_MAC_MD_1000BX = 7,/* 1000Base-X only */
};
#define GM_GPCR_SPEED_1000 (GM_GPCR_GIGS_ENA | GM_GPCR_SPEED_100)
-#define GM_GPCR_AU_ALL_DIS (GM_GPCR_AU_DUP_DIS | GM_GPCR_AU_FCT_DIS|GM_GPCR_AU_SPD_DIS)
/* GM_TX_CTRL 16 bit r/w Transmit Control Register */
enum {
/* GM_SERIAL_MODE 16 bit r/w Serial Mode Register */
enum {
GM_SMOD_DATABL_MSK = 0x1f<<11, /* Bit 15..11: Data Blinder (r/o) */
- GM_SMOD_LIMIT_4 = 1<<10, /* Bit 10: 4 consecutive Tx trials */
- GM_SMOD_VLAN_ENA = 1<<9, /* Bit 9: Enable VLAN (Max. Frame Len) */
- GM_SMOD_JUMBO_ENA = 1<<8, /* Bit 8: Enable Jumbo (Max. Frame Len) */
- GM_SMOD_IPG_MSK = 0x1f /* Bit 4..0: Inter-Packet Gap (IPG) */
+ GM_SMOD_LIMIT_4 = 1<<10, /* 4 consecutive Tx trials */
+ GM_SMOD_VLAN_ENA = 1<<9, /* Enable VLAN (Max. Frame Len) */
+ GM_SMOD_JUMBO_ENA = 1<<8, /* Enable Jumbo (Max. Frame Len) */
+
+ GM_NEW_FLOW_CTRL = 1<<6, /* Enable New Flow-Control */
+
+ GM_SMOD_IPG_MSK = 0x1f /* Bit 4..0: Inter-Packet Gap (IPG) */
};
#define DATA_BLIND_VAL(x) (((x)<<11) & GM_SMOD_DATABL_MSK)
/* Receive Frame Status Encoding */
enum {
- GMR_FS_LEN = 0xffff<<16, /* Bit 31..16: Rx Frame Length */
+ GMR_FS_LEN = 0x7fff<<16, /* Bit 30..16: Rx Frame Length */
GMR_FS_VLAN = 1<<13, /* VLAN Packet */
GMR_FS_JABBER = 1<<12, /* Jabber Packet */
GMR_FS_UN_SIZE = 1<<11, /* Undersize Packet */
/* RX_GMF_CTRL_T 32 bit Rx GMAC FIFO Control/Test */
enum {
+ RX_GCLKMAC_ENA = 1<<31, /* RX MAC Clock Gating Enable */
+ RX_GCLKMAC_OFF = 1<<30,
+
+ RX_STFW_DIS = 1<<29, /* RX Store and Forward Enable */
+ RX_STFW_ENA = 1<<28,
+
RX_TRUNC_ON = 1<<27, /* enable packet truncation */
RX_TRUNC_OFF = 1<<26, /* disable packet truncation */
RX_VLAN_STRIP_ON = 1<<25, /* enable VLAN stripping */
RX_VLAN_STRIP_OFF = 1<<24, /* disable VLAN stripping */
+ RX_MACSEC_FLUSH_ON = 1<<23,
+ RX_MACSEC_FLUSH_OFF = 1<<22,
+ RX_MACSEC_ASF_FLUSH_ON = 1<<21,
+ RX_MACSEC_ASF_FLUSH_OFF = 1<<20,
+
+ GMF_RX_OVER_ON = 1<<19, /* enable flushing on receive overrun */
+ GMF_RX_OVER_OFF = 1<<18, /* disable flushing on receive overrun */
+ GMF_ASF_RX_OVER_ON = 1<<17, /* enable flushing of ASF when overrun */
+ GMF_ASF_RX_OVER_OFF = 1<<16, /* disable flushing of ASF when overrun */
+
GMF_WP_TST_ON = 1<<14, /* Write Pointer Test On */
GMF_WP_TST_OFF = 1<<13, /* Write Pointer Test Off */
GMF_WP_STEP = 1<<12, /* Write Pointer Step/Increment */
GMF_RX_CTRL_DEF = GMF_OPER_ON | GMF_RX_F_FL_ON,
};
+/* RX_GMF_FL_CTRL 16 bit Rx GMAC FIFO Flush Control (Yukon-Supreme) */
+enum {
+ RX_IPV6_SA_MOB_ENA = 1<<9, /* IPv6 SA Mobility Support Enable */
+ RX_IPV6_SA_MOB_DIS = 1<<8, /* IPv6 SA Mobility Support Disable */
+ RX_IPV6_DA_MOB_ENA = 1<<7, /* IPv6 DA Mobility Support Enable */
+ RX_IPV6_DA_MOB_DIS = 1<<6, /* IPv6 DA Mobility Support Disable */
+ RX_PTR_SYNCDLY_ENA = 1<<5, /* Pointers Delay Synch Enable */
+ RX_PTR_SYNCDLY_DIS = 1<<4, /* Pointers Delay Synch Disable */
+ RX_ASF_NEWFLAG_ENA = 1<<3, /* RX ASF Flag New Logic Enable */
+ RX_ASF_NEWFLAG_DIS = 1<<2, /* RX ASF Flag New Logic Disable */
+ RX_FLSH_MISSPKT_ENA = 1<<1, /* RX Flush Miss-Packet Enable */
+ RX_FLSH_MISSPKT_DIS = 1<<0, /* RX Flush Miss-Packet Disable */
+};
+
+/* TX_GMF_EA 32 bit Tx GMAC FIFO End Address */
+enum {
+ TX_DYN_WM_ENA = 3, /* Yukon-FE+ specific */
+};
/* TX_GMF_CTRL_T 32 bit Tx GMAC FIFO Control/Test */
enum {
- TX_STFW_DIS = 1<<31,/* Disable Store & Forward (Yukon-EC Ultra) */
- TX_STFW_ENA = 1<<30,/* Enable Store & Forward (Yukon-EC Ultra) */
+ TX_STFW_DIS = 1<<31,/* Disable Store & Forward */
+ TX_STFW_ENA = 1<<30,/* Enable Store & Forward */
TX_VLAN_TAG_ON = 1<<25,/* enable VLAN tagging */
TX_VLAN_TAG_OFF = 1<<24,/* disable VLAN tagging */
- TX_JUMBO_ENA = 1<<23,/* PCI Jumbo Mode enable (Yukon-EC Ultra) */
- TX_JUMBO_DIS = 1<<22,/* PCI Jumbo Mode enable (Yukon-EC Ultra) */
+ TX_PCI_JUM_ENA = 1<<23,/* PCI Jumbo Mode enable */
+ TX_PCI_JUM_DIS = 1<<22,/* PCI Jumbo Mode enable */
GMF_WSP_TST_ON = 1<<18,/* Write Shadow Pointer Test On */
GMF_WSP_TST_OFF = 1<<17,/* Write Shadow Pointer Test Off */
/* GMAC_CTRL 32 bit GMAC Control Reg (YUKON only) */
enum {
+ GMC_SET_RST = 1<<15,/* MAC SEC RST */
+ GMC_SEC_RST_OFF = 1<<14,/* MAC SEC RSt OFF */
+ GMC_BYP_MACSECRX_ON = 1<<13,/* Bypass macsec RX */
+ GMC_BYP_MACSECRX_OFF= 1<<12,/* Bypass macsec RX off */
+ GMC_BYP_MACSECTX_ON = 1<<11,/* Bypass macsec TX */
+ GMC_BYP_MACSECTX_OFF= 1<<10,/* Bypass macsec TX off*/
+ GMC_BYP_RETR_ON = 1<<9, /* Bypass retransmit FIFO On */
+ GMC_BYP_RETR_OFF= 1<<8, /* Bypass retransmit FIFO Off */
+
GMC_H_BURST_ON = 1<<7, /* Half Duplex Burst Mode On */
GMC_H_BURST_OFF = 1<<6, /* Half Duplex Burst Mode Off */
GMC_F_LOOPB_ON = 1<<5, /* FIFO Loopback On */
/* GPHY_CTRL 32 bit GPHY Control Reg (YUKON only) */
enum {
+ GPC_TX_PAUSE = 1<<30, /* Tx pause enabled (ro) */
+ GPC_RX_PAUSE = 1<<29, /* Rx pause enabled (ro) */
+ GPC_SPEED = 3<<27, /* PHY speed (ro) */
+ GPC_LINK = 1<<26, /* Link up (ro) */
+ GPC_DUPLEX = 1<<25, /* Duplex (ro) */
+ GPC_CLOCK = 1<<24, /* 125Mhz clock stable (ro) */
+
+ GPC_PDOWN = 1<<23, /* Internal regulator 2.5 power down */
+ GPC_TSTMODE = 1<<22, /* Test mode */
+ GPC_REG18 = 1<<21, /* Reg18 Power down */
+ GPC_REG12SEL = 3<<19, /* Reg12 power setting */
+ GPC_REG18SEL = 3<<17, /* Reg18 power setting */
+ GPC_SPILOCK = 1<<16, /* SPI lock (ASF) */
+
+ GPC_LEDMUX = 3<<14, /* LED Mux */
+ GPC_INTPOL = 1<<13, /* Interrupt polarity */
+ GPC_DETECT = 1<<12, /* Energy detect */
+ GPC_1000HD = 1<<11, /* Enable 1000Mbit HD */
+ GPC_SLAVE = 1<<10, /* Slave mode */
+ GPC_PAUSE = 1<<9, /* Pause enable */
+ GPC_LEDCTL = 3<<6, /* GPHY Leds */
+
GPC_RST_CLR = 1<<1, /* Clear GPHY Reset */
GPC_RST_SET = 1<<0, /* Set GPHY Reset */
};
OP_ADDR64VLAN = OP_ADDR64 | OP_VLAN,
OP_LRGLEN = 0x24,
OP_LRGLENVLAN = OP_LRGLEN | OP_VLAN,
+ OP_MSS = 0x28,
+ OP_MSSVLAN = OP_MSS | OP_VLAN,
+
OP_BUFFER = 0x40,
OP_PACKET = 0x41,
OP_LARGESEND = 0x43,
+ OP_LSOV2 = 0x45,
/* YUKON-2 STATUS opcodes defines */
OP_RXSTAT = 0x60,
OP_RXTIMEVLAN = OP_RXTIMESTAMP | OP_RXVLAN,
OP_RSS_HASH = 0x65,
OP_TXINDEXLE = 0x68,
+ OP_MACSEC = 0x6c,
+ OP_PUTIDX = 0x70,
+};
+
+enum status_css {
+ CSS_TCPUDPCSOK = 1<<7, /* TCP / UDP checksum is ok */
+ CSS_ISUDP = 1<<6, /* packet is a UDP packet */
+ CSS_ISTCP = 1<<5, /* packet is a TCP packet */
+ CSS_ISIPFRAG = 1<<4, /* packet is a TCP/UDP frag, CS calc not done */
+ CSS_ISIPV6 = 1<<3, /* packet is a IPv6 packet */
+ CSS_IPV4CSUMOK = 1<<2, /* IP v4: TCP header checksum is ok */
+ CSS_ISIPV4 = 1<<1, /* packet is a IPv4 packet */
+ CSS_LINK_BIT = 1<<0, /* port number (legacy) */
};
/* Yukon 2 hardware interface */
struct sky2_status_le {
__le32 status; /* also checksum */
__le16 length; /* also vlan tag */
- u8 link;
+ u8 css;
u8 opcode;
} __attribute((packed));
struct tx_ring_info {
struct sk_buff *skb;
- DECLARE_PCI_UNMAP_ADDR(mapaddr);
- DECLARE_PCI_UNMAP_ADDR(maplen);
+ unsigned long flags;
+#define TX_MAP_SINGLE 0x0001
+#define TX_MAP_PAGE 0x0002
+ DEFINE_DMA_UNMAP_ADDR(mapaddr);
+ DEFINE_DMA_UNMAP_LEN(maplen);
};
struct rx_ring_info {
struct sk_buff *skb;
dma_addr_t data_addr;
- DECLARE_PCI_UNMAP_ADDR(data_size);
+ DEFINE_DMA_UNMAP_LEN(data_size);
dma_addr_t frag_addr[ETH_JUMBO_MTU >> PAGE_SHIFT];
};
struct tx_ring_info *tx_ring;
struct sky2_tx_le *tx_le;
+ u16 tx_ring_size;
u16 tx_cons; /* next le to check */
u16 tx_prod; /* next le to use */
- u32 tx_addr64;
+ u16 tx_next; /* debug only */
+
u16 tx_pending;
u16 tx_last_mss;
+ u32 tx_last_upper;
u32 tx_tcpsum;
struct rx_ring_info *rx_ring ____cacheline_aligned_in_smp;
struct sky2_rx_le *rx_le;
- u32 rx_addr64;
+
u16 rx_next; /* next re to check */
u16 rx_put; /* next le index to use */
u16 rx_pending;
u16 rx_tag;
struct vlan_group *vlgrp;
#endif
+ struct {
+ unsigned long last;
+ u32 mac_rp;
+ u8 mac_lev;
+ u8 fifo_rp;
+ u8 fifo_lev;
+ } check;
dma_addr_t rx_le_map;
dma_addr_t tx_le_map;
+
u16 advertising; /* ADVERTISED_ bits */
- u16 speed; /* SPEED_1000, SPEED_100, ... */
- u8 autoneg; /* AUTONEG_ENABLE, AUTONEG_DISABLE */
- u8 duplex; /* DUPLEX_HALF, DUPLEX_FULL */
- u8 rx_csum;
- u8 wol;
+ u16 speed; /* SPEED_1000, SPEED_100, ... */
+ u8 wol; /* WAKE_ bits */
+ u8 duplex; /* DUPLEX_HALF, DUPLEX_FULL */
+ u16 flags;
+#define SKY2_FLAG_RX_CHECKSUM 0x0001
+#define SKY2_FLAG_AUTO_SPEED 0x0002
+#define SKY2_FLAG_AUTO_PAUSE 0x0004
+
enum flow_control flow_mode;
enum flow_control flow_status;
- struct net_device_stats net_stats;
-
+#ifdef CONFIG_SKY2_DEBUG
+ struct dentry *debugfs;
+#endif
};
struct sky2_hw {
void __iomem *regs;
struct pci_dev *pdev;
+ struct napi_struct napi;
struct net_device *dev[2];
+ unsigned long flags;
+#define SKY2_HW_USE_MSI 0x00000001
+#define SKY2_HW_FIBRE_PHY 0x00000002
+#define SKY2_HW_GIGABIT 0x00000004
+#define SKY2_HW_NEWER_PHY 0x00000008
+#define SKY2_HW_RAM_BUFFER 0x00000010
+#define SKY2_HW_NEW_LE 0x00000020 /* new LSOv2 format */
+#define SKY2_HW_AUTO_TX_SUM 0x00000040 /* new IP decode for Tx */
+#define SKY2_HW_ADV_POWER_CTL 0x00000080 /* additional PHY power regs */
+#define SKY2_HW_RSS_BROKEN 0x00000100
u8 chip_id;
u8 chip_rev;
u8 ports;
struct sky2_status_le *st_le;
+ u32 st_size;
u32 st_idx;
dma_addr_t st_dma;
- struct timer_list idle_timer;
+ struct timer_list watchdog_timer;
struct work_struct restart_work;
- int msi;
wait_queue_head_t msi_wait;
+
+ char irq_name[0];
};
static inline int sky2_is_copper(const struct sky2_hw *hw)
{
- return !(hw->pmd_type == 'L' || hw->pmd_type == 'S' || hw->pmd_type == 'P');
+ return !(hw->flags & SKY2_HW_FIBRE_PHY);
}
/* Register accessor for memory mapped device */
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff