* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
-/*
- * TOTEST
- * - speed setting
- * - suspend/resume
- */
-
#include <linux/config.h>
#include <linux/crc32.h>
#include <linux/kernel.h>
#include "sky2.h"
#define DRV_NAME "sky2"
-#define DRV_VERSION "0.13"
+#define DRV_VERSION "0.15"
#define PFX DRV_NAME " "
/*
pr_debug("sky2_set_power_state %d\n", state);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
- pci_read_config_word(hw->pdev, hw->pm_cap + PCI_PM_PMC, &power_control);
- vaux = (sky2_read8(hw, B0_CTST) & Y2_VAUX_AVAIL) &&
+ power_control = sky2_pci_read16(hw, hw->pm_cap + PCI_PM_PMC);
+ vaux = (sky2_read16(hw, B0_CTST) & Y2_VAUX_AVAIL) &&
(power_control & PCI_PM_CAP_PME_D3cold);
- pci_read_config_word(hw->pdev, hw->pm_cap + PCI_PM_CTRL, &power_control);
+ power_control = sky2_pci_read16(hw, hw->pm_cap + PCI_PM_CTRL);
power_control |= PCI_PM_CTRL_PME_STATUS;
power_control &= ~(PCI_PM_CTRL_STATE_MASK);
sky2_write8(hw, B2_Y2_CLK_GATE, 0);
/* Turn off phy power saving */
- pci_read_config_dword(hw->pdev, PCI_DEV_REG1, ®1);
+ reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
reg1 &= ~(PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
/* looks like this XL is back asswards .. */
if (hw->ports > 1)
reg1 |= PCI_Y2_PHY2_COMA;
}
- pci_write_config_dword(hw->pdev, PCI_DEV_REG1, reg1);
+
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U) {
+ sky2_pci_write32(hw, PCI_DEV_REG3, 0);
+ reg1 = sky2_pci_read32(hw, PCI_DEV_REG4);
+ reg1 &= P_ASPM_CONTROL_MSK;
+ sky2_pci_write32(hw, PCI_DEV_REG4, reg1);
+ sky2_pci_write32(hw, PCI_DEV_REG5, 0);
+ }
+
+ sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
+
break;
case PCI_D3hot:
case PCI_D3cold:
/* Turn on phy power saving */
- pci_read_config_dword(hw->pdev, PCI_DEV_REG1, ®1);
+ reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
reg1 &= ~(PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
else
reg1 |= (PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
- pci_write_config_dword(hw->pdev, PCI_DEV_REG1, reg1);
+ sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
sky2_write8(hw, B2_Y2_CLK_GATE, 0);
ret = -1;
}
- pci_write_config_byte(hw->pdev, hw->pm_cap + PCI_PM_CTRL, power_control);
+ sky2_pci_write16(hw, hw->pm_cap + PCI_PM_CTRL, power_control);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
return ret;
}
ledover |= PHY_M_LED_MO_RX(MO_LED_OFF);
}
- gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev >= 2) {
+ /* apply fixes in PHY AFE */
+ gm_phy_write(hw, port, 22, 255);
+ /* increase differential signal amplitude in 10BASE-T */
+ gm_phy_write(hw, port, 24, 0xaa99);
+ gm_phy_write(hw, port, 23, 0x2011);
- if (sky2->autoneg == AUTONEG_DISABLE || sky2->speed == SPEED_100) {
- /* turn on 100 Mbps LED (LED_LINK100) */
- ledover |= PHY_M_LED_MO_100(MO_LED_ON);
- }
+ /* fix for IEEE A/B Symmetry failure in 1000BASE-T */
+ gm_phy_write(hw, port, 24, 0xa204);
+ gm_phy_write(hw, port, 23, 0x2002);
- if (ledover)
- gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover);
+ /* set page register to 0 */
+ gm_phy_write(hw, port, 22, 0);
+ } else {
+ gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
+ if (sky2->autoneg == AUTONEG_DISABLE || sky2->speed == SPEED_100) {
+ /* turn on 100 Mbps LED (LED_LINK100) */
+ ledover |= PHY_M_LED_MO_100(MO_LED_ON);
+ }
+
+ if (ledover)
+ gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover);
+
+ }
/* Enable phy interrupt on auto-negotiation complete (or link up) */
if (sky2->autoneg == AUTONEG_ENABLE)
gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_AN_COMPL);
switch (sky2->speed) {
case SPEED_1000:
+ reg &= ~GM_GPCR_SPEED_100;
reg |= GM_GPCR_SPEED_1000;
- /* fallthru */
+ break;
case SPEED_100:
+ reg &= ~GM_GPCR_SPEED_1000;
reg |= GM_GPCR_SPEED_100;
+ break;
+ case SPEED_10:
+ reg &= ~(GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100);
+ break;
}
if (sky2->duplex == DUPLEX_FULL)
sky2->rx_put = sky2->rx_next = 0;
sky2_qset(hw, rxq);
+
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev >= 2) {
+ /* MAC Rx RAM Read is controlled by hardware */
+ sky2_write32(hw, Q_ADDR(rxq, Q_F), F_M_RX_RAM_DIS);
+ }
+
sky2_prefetch_init(hw, rxq, sky2->rx_le_map, RX_LE_SIZE - 1);
rx_set_checksum(sky2);
RB_RST_SET);
sky2_qset(hw, txqaddr[port]);
- if (hw->chip_id == CHIP_ID_YUKON_EC_U)
- sky2_write16(hw, Q_ADDR(txqaddr[port], Q_AL), 0x1a0);
+ /* Set almost empty threshold */
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev == 1)
+ sky2_write16(hw, Q_ADDR(txqaddr[port], Q_AL), 0x1a0);
sky2_prefetch_init(hw, txqaddr[port], sky2->tx_le_map,
TX_RING_SIZE - 1);
goto err_out;
/* Enable interrupts from phy/mac for port */
+ spin_lock_irq(&hw->hw_lock);
hw->intr_mask |= (port == 0) ? Y2_IS_PORT_1 : Y2_IS_PORT_2;
sky2_write32(hw, B0_IMSK, hw->intr_mask);
+ spin_unlock_irq(&hw->hw_lock);
return 0;
err_out:
netif_stop_queue(dev);
/* Disable port IRQ */
- local_irq_disable();
+ spin_lock_irq(&hw->hw_lock);
hw->intr_mask &= ~((sky2->port == 0) ? Y2_IS_IRQ_PHY1 : Y2_IS_IRQ_PHY2);
sky2_write32(hw, B0_IMSK, hw->intr_mask);
- local_irq_enable();
+ spin_unlock_irq(&hw->hw_lock);
flush_scheduled_work();
sky2_write8(hw, SK_REG(port, GMAC_IRQ_MSK), GMAC_DEF_MSK);
reg = gma_read16(hw, port, GM_GP_CTRL);
+ if (sky2->autoneg == AUTONEG_DISABLE) {
+ reg |= GM_GPCR_AU_ALL_DIS;
+
+ /* Is write/read necessary? Copied from sky2_mac_init */
+ gma_write16(hw, port, GM_GP_CTRL, reg);
+ gma_read16(hw, port, GM_GP_CTRL);
+
+ switch (sky2->speed) {
+ case SPEED_1000:
+ reg &= ~GM_GPCR_SPEED_100;
+ reg |= GM_GPCR_SPEED_1000;
+ break;
+ case SPEED_100:
+ reg &= ~GM_GPCR_SPEED_1000;
+ reg |= GM_GPCR_SPEED_100;
+ break;
+ case SPEED_10:
+ reg &= ~(GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100);
+ break;
+ }
+ } else
+ reg &= ~GM_GPCR_AU_ALL_DIS;
+
if (sky2->duplex == DUPLEX_FULL || sky2->autoneg == AUTONEG_ENABLE)
reg |= GM_GPCR_DUP_FULL;
out:
up(&sky2->phy_sema);
- local_irq_disable();
+ spin_lock_irq(&hw->hw_lock);
hw->intr_mask |= (sky2->port == 0) ? Y2_IS_IRQ_PHY1 : Y2_IS_IRQ_PHY2;
sky2_write32(hw, B0_IMSK, hw->intr_mask);
- local_irq_enable();
+ spin_unlock_irq(&hw->hw_lock);
}
u16 hwidx;
u16 tx_done[2] = { TX_NO_STATUS, TX_NO_STATUS };
+ sky2_write32(hw, STAT_CTRL, SC_STAT_CLR_IRQ);
+
+ /*
+ * Kick the STAT_LEV_TIMER_CTRL timer.
+ * This fixes my hangs on Yukon-EC (0xb6) rev 1.
+ * The if clause is there to start the timer only if it has been
+ * configured correctly and not been disabled via ethtool.
+ */
+ if (sky2_read8(hw, STAT_LEV_TIMER_CTRL) == TIM_START) {
+ sky2_write8(hw, STAT_LEV_TIMER_CTRL, TIM_STOP);
+ sky2_write8(hw, STAT_LEV_TIMER_CTRL, TIM_START);
+ }
+
hwidx = sky2_read16(hw, STAT_PUT_IDX);
BUG_ON(hwidx >= STATUS_RING_SIZE);
rmb();
}
exit_loop:
- sky2_write32(hw, STAT_CTRL, SC_STAT_CLR_IRQ);
-
sky2_tx_check(hw, 0, tx_done[0]);
sky2_tx_check(hw, 1, tx_done[1]);
- if (sky2_read16(hw, STAT_PUT_IDX) == hw->st_idx) {
- /* need to restart TX timer */
- if (is_ec_a1(hw)) {
- sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_STOP);
- sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START);
- }
+ if (sky2_read8(hw, STAT_TX_TIMER_CTRL) == TIM_START) {
+ sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_STOP);
+ sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START);
+ }
+
+ if (likely(work_done < to_do)) {
+ spin_lock_irq(&hw->hw_lock);
+ __netif_rx_complete(dev0);
- netif_rx_complete(dev0);
hw->intr_mask |= Y2_IS_STAT_BMU;
sky2_write32(hw, B0_IMSK, hw->intr_mask);
+ spin_unlock_irq(&hw->hw_lock);
+
return 0;
} else {
*budget -= work_done;
if (status & (Y2_IS_MST_ERR | Y2_IS_IRQ_STAT)) {
u16 pci_err;
- pci_read_config_word(hw->pdev, PCI_STATUS, &pci_err);
+ pci_err = sky2_pci_read16(hw, PCI_STATUS);
if (net_ratelimit())
printk(KERN_ERR PFX "%s: pci hw error (0x%x)\n",
pci_name(hw->pdev), pci_err);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
- pci_write_config_word(hw->pdev, PCI_STATUS,
+ sky2_pci_write16(hw, PCI_STATUS,
pci_err | PCI_STATUS_ERROR_BITS);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
}
/* PCI-Express uncorrectable Error occurred */
u32 pex_err;
- pci_read_config_dword(hw->pdev, PEX_UNC_ERR_STAT, &pex_err);
+ pex_err = sky2_pci_read32(hw, PEX_UNC_ERR_STAT);
if (net_ratelimit())
printk(KERN_ERR PFX "%s: pci express error (0x%x)\n",
/* clear the interrupt */
sky2_write32(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
- pci_write_config_dword(hw->pdev, PEX_UNC_ERR_STAT,
+ sky2_pci_write32(hw, PEX_UNC_ERR_STAT,
0xffffffffUL);
sky2_write32(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
hw->intr_mask &= ~(port == 0 ? Y2_IS_IRQ_PHY1 : Y2_IS_IRQ_PHY2);
sky2_write32(hw, B0_IMSK, hw->intr_mask);
+
schedule_work(&sky2->phy_task);
}
if (status == 0 || status == ~0)
return IRQ_NONE;
+ spin_lock(&hw->hw_lock);
if (status & Y2_IS_HW_ERR)
sky2_hw_intr(hw);
sky2_write32(hw, B0_Y2_SP_ICR, 2);
- sky2_read32(hw, B0_IMSK);
+ spin_unlock(&hw->hw_lock);
return IRQ_HANDLED;
}
static int sky2_reset(struct sky2_hw *hw)
{
- u32 ctst;
u16 status;
u8 t8, pmd_type;
int i;
- ctst = sky2_read32(hw, B0_CTST);
-
sky2_write8(hw, B0_CTST, CS_RST_CLR);
+
hw->chip_id = sky2_read8(hw, B2_CHIP_ID);
if (hw->chip_id < CHIP_ID_YUKON_XL || hw->chip_id > CHIP_ID_YUKON_FE) {
printk(KERN_ERR PFX "%s: unsupported chip type 0x%x\n",
return -EOPNOTSUPP;
}
- /* ring for status responses */
- hw->st_le = pci_alloc_consistent(hw->pdev, STATUS_LE_BYTES,
- &hw->st_dma);
- if (!hw->st_le)
- return -ENOMEM;
-
/* disable ASF */
if (hw->chip_id <= CHIP_ID_YUKON_EC) {
sky2_write8(hw, B28_Y2_ASF_STAT_CMD, Y2_ASF_RESET);
sky2_write8(hw, B0_CTST, CS_RST_CLR);
/* clear PCI errors, if any */
- pci_read_config_word(hw->pdev, PCI_STATUS, &status);
+ status = sky2_pci_read16(hw, PCI_STATUS);
+
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
- pci_write_config_word(hw->pdev, PCI_STATUS,
- status | PCI_STATUS_ERROR_BITS);
+ sky2_pci_write16(hw, PCI_STATUS, status | PCI_STATUS_ERROR_BITS);
+
sky2_write8(hw, B0_CTST, CS_MRST_CLR);
/* clear any PEX errors */
- if (is_pciex(hw)) {
- u16 lstat;
- pci_write_config_dword(hw->pdev, PEX_UNC_ERR_STAT,
- 0xffffffffUL);
- pci_read_config_word(hw->pdev, PEX_LNK_STAT, &lstat);
- }
+ if (pci_find_capability(hw->pdev, PCI_CAP_ID_EXP))
+ sky2_pci_write32(hw, PEX_UNC_ERR_STAT, 0xffffffffUL);
+
pmd_type = sky2_read8(hw, B2_PMD_TYP);
hw->copper = !(pmd_type == 'L' || pmd_type == 'S');
sky2_write8(hw, STAT_FIFO_ISR_WM, 16);
sky2_write32(hw, STAT_TX_TIMER_INI, sky2_us2clk(hw, 1000));
- sky2_write32(hw, STAT_LEV_TIMER_INI, sky2_us2clk(hw, 100));
- sky2_write32(hw, STAT_ISR_TIMER_INI, sky2_us2clk(hw, 20));
+ sky2_write32(hw, STAT_ISR_TIMER_INI, sky2_us2clk(hw, 7));
}
/* enable status unit */
static int sky2_set_mac_address(struct net_device *dev, void *p)
{
struct sky2_port *sky2 = netdev_priv(dev);
- struct sockaddr *addr = p;
+ struct sky2_hw *hw = sky2->hw;
+ unsigned port = sky2->port;
+ const struct sockaddr *addr = p;
if (!is_valid_ether_addr(addr->sa_data))
return -EADDRNOTAVAIL;
memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN);
- memcpy_toio(sky2->hw->regs + B2_MAC_1 + sky2->port * 8,
+ memcpy_toio(hw->regs + B2_MAC_1 + port * 8,
dev->dev_addr, ETH_ALEN);
- memcpy_toio(sky2->hw->regs + B2_MAC_2 + sky2->port * 8,
+ memcpy_toio(hw->regs + B2_MAC_2 + port * 8,
dev->dev_addr, ETH_ALEN);
- if (netif_running(dev))
- sky2_phy_reinit(sky2);
+ /* virtual address for data */
+ gma_set_addr(hw, port, GM_SRC_ADDR_2L, dev->dev_addr);
+
+ /* physical address: used for pause frames */
+ gma_set_addr(hw, port, GM_SRC_ADDR_1L, dev->dev_addr);
return 0;
}
(ecmd->rx_coalesce_usecs_irq < tmin || ecmd->rx_coalesce_usecs_irq > tmax))
return -EINVAL;
- if (ecmd->tx_max_coalesced_frames > 0xffff)
+ if (ecmd->tx_max_coalesced_frames >= TX_RING_SIZE-1)
return -EINVAL;
- if (ecmd->rx_max_coalesced_frames > 0xff)
+ if (ecmd->rx_max_coalesced_frames > RX_MAX_PENDING)
return -EINVAL;
- if (ecmd->rx_max_coalesced_frames_irq > 0xff)
+ if (ecmd->rx_max_coalesced_frames_irq >RX_MAX_PENDING)
return -EINVAL;
if (ecmd->tx_coalesce_usecs == 0)
if (ecmd->rx_coalesce_usecs_irq == 0)
sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_STOP);
else {
- sky2_write32(hw, STAT_TX_TIMER_INI,
+ sky2_write32(hw, STAT_ISR_TIMER_INI,
sky2_us2clk(hw, ecmd->rx_coalesce_usecs_irq));
sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_START);
}
}
}
-#ifdef __BIG_ENDIAN
- /* byte swap descriptors in hardware */
- {
- u32 reg;
-
- pci_read_config_dword(pdev, PCI_DEV_REG2, ®);
- reg |= PCI_REV_DESC;
- pci_write_config_dword(pdev, PCI_DEV_REG2, reg);
- }
-#endif
-
err = -ENOMEM;
hw = kzalloc(sizeof(*hw), GFP_KERNEL);
if (!hw) {
goto err_out_free_hw;
}
hw->pm_cap = pm_cap;
+ spin_lock_init(&hw->hw_lock);
+
+#ifdef __BIG_ENDIAN
+ /* byte swap descriptors in hardware */
+ {
+ u32 reg;
+
+ reg = sky2_pci_read32(hw, PCI_DEV_REG2);
+ reg |= PCI_REV_DESC;
+ sky2_pci_write32(hw, PCI_DEV_REG2, reg);
+ }
+#endif
+
+ /* ring for status responses */
+ hw->st_le = pci_alloc_consistent(hw->pdev, STATUS_LE_BYTES,
+ &hw->st_dma);
+ if (!hw->st_le)
+ goto err_out_iounmap;
err = sky2_reset(hw);
if (err)
}
}
- err = request_irq(pdev->irq, sky2_intr, SA_SHIRQ, DRV_NAME, hw);
+ err = request_irq(pdev->irq, sky2_intr, SA_SHIRQ | SA_SAMPLE_RANDOM,
+ DRV_NAME, hw);
if (err) {
printk(KERN_ERR PFX "%s: cannot assign irq %d\n",
pci_name(pdev), pdev->irq);
static int sky2_resume(struct pci_dev *pdev)
{
struct sky2_hw *hw = pci_get_drvdata(pdev);
- int i;
+ int i, err;
pci_restore_state(pdev);
pci_enable_wake(pdev, PCI_D0, 0);
- sky2_set_power_state(hw, PCI_D0);
+ err = sky2_set_power_state(hw, PCI_D0);
+ if (err)
+ goto out;
- sky2_reset(hw);
+ err = sky2_reset(hw);
+ if (err)
+ goto out;
for (i = 0; i < 2; i++) {
struct net_device *dev = hw->dev[i];
- if (dev) {
- if (netif_running(dev)) {
- netif_device_attach(dev);
- if (sky2_up(dev))
- dev_close(dev);
+ if (dev && netif_running(dev)) {
+ netif_device_attach(dev);
+ err = sky2_up(dev);
+ if (err) {
+ printk(KERN_ERR PFX "%s: could not up: %d\n",
+ dev->name, err);
+ dev_close(dev);
+ break;
}
}
}
- return 0;
+out:
+ return err;
}
#endif
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff