#include "sky2.h"
#define DRV_NAME "sky2"
-#define DRV_VERSION "1.25"
+#define DRV_VERSION "1.26"
#define PFX DRV_NAME " "
/*
static DEFINE_PCI_DEVICE_TABLE(sky2_id_table) = {
{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9000) }, /* SK-9Sxx */
{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9E00) }, /* SK-9Exx */
+ { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9E01) }, /* SK-9E21M */
{ PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4b00) }, /* DGE-560T */
{ PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4001) }, /* DGE-550SX */
{ PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4B02) }, /* DGE-560SX */
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x436D) }, /* 88E8055 */
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4370) }, /* 88E8075 */
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4380) }, /* 88E8057 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4381) }, /* 88E8059 */
{ 0 }
};
ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO);
/* downshift on PHY 88E1112 and 88E1149 is changed */
- if ( (sky2->flags & SKY2_FLAG_AUTO_SPEED)
- && (hw->flags & SKY2_HW_NEWER_PHY)) {
+ if ( (sky2->flags & SKY2_FLAG_AUTO_SPEED) &&
+ (hw->flags & SKY2_HW_NEWER_PHY)) {
/* set downshift counter to 3x and enable downshift */
ctrl &= ~PHY_M_PC_DSC_MSK;
ctrl |= PHY_M_PC_DSC(2) | PHY_M_PC_DOWN_S_ENA;
/* apply workaround for integrated resistors calibration */
gm_phy_write(hw, port, PHY_MARV_PAGE_ADDR, 17);
gm_phy_write(hw, port, PHY_MARV_PAGE_DATA, 0x3f60);
+ } else if (hw->chip_id == CHIP_ID_YUKON_OPT && hw->chip_rev == 0) {
+ /* apply fixes in PHY AFE */
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0x00ff);
+
+ /* apply RDAC termination workaround */
+ gm_phy_write(hw, port, 24, 0x2800);
+ gm_phy_write(hw, port, 23, 0x2001);
+
+ /* set page register back to 0 */
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0);
} else if (hw->chip_id != CHIP_ID_YUKON_EX &&
hw->chip_id < CHIP_ID_YUKON_SUPR) {
/* no effect on Yukon-XL */
gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
- if ( !(sky2->flags & SKY2_FLAG_AUTO_SPEED)
- || sky2->speed == SPEED_100) {
+ if (!(sky2->flags & SKY2_FLAG_AUTO_SPEED) ||
+ sky2->speed == SPEED_100) {
/* turn on 100 Mbps LED (LED_LINK100) */
ledover |= PHY_M_LED_MO_100(MO_LED_ON);
}
if ( (hw->chip_id == CHIP_ID_YUKON_EX &&
hw->chip_rev != CHIP_REV_YU_EX_A0) ||
- hw->chip_id == CHIP_ID_YUKON_FE_P ||
- hw->chip_id == CHIP_ID_YUKON_SUPR) {
+ hw->chip_id >= CHIP_ID_YUKON_FE_P) {
/* Yukon-Extreme B0 and further Extreme devices */
/* enable Store & Forward mode for TX */
/* On chips without ram buffer, pause is controled by MAC level */
if (!(hw->flags & SKY2_HW_RAM_BUFFER)) {
- sky2_write8(hw, SK_REG(port, RX_GMF_LP_THR), 768/8);
- sky2_write8(hw, SK_REG(port, RX_GMF_UP_THR), 1024/8);
+ /* Pause threshold is scaled by 8 in bytes */
+ if (hw->chip_id == CHIP_ID_YUKON_FE_P &&
+ hw->chip_rev == CHIP_REV_YU_FE2_A0)
+ reg = 1568 / 8;
+ else
+ reg = 1024 / 8;
+ sky2_write16(hw, SK_REG(port, RX_GMF_UP_THR), reg);
+ sky2_write16(hw, SK_REG(port, RX_GMF_LP_THR), 768 / 8);
sky2_set_tx_stfwd(hw, port);
}
static inline struct sky2_tx_le *get_tx_le(struct sky2_port *sky2, u16 *slot)
{
struct sky2_tx_le *le = sky2->tx_le + *slot;
- struct tx_ring_info *re = sky2->tx_ring + *slot;
*slot = RING_NEXT(*slot, sky2->tx_ring_size);
- re->flags = 0;
- re->skb = NULL;
le->ctrl = 0;
return le;
}
/* These chips have no ram buffer?
* MAC Rx RAM Read is controlled by hardware */
if (hw->chip_id == CHIP_ID_YUKON_EC_U &&
- (hw->chip_rev == CHIP_REV_YU_EC_U_A1
- || hw->chip_rev == CHIP_REV_YU_EC_U_B0))
+ (hw->chip_rev == CHIP_REV_YU_EC_U_A1 ||
+ hw->chip_rev == CHIP_REV_YU_EC_U_B0))
sky2_write32(hw, Q_ADDR(rxq, Q_TEST), F_M_RX_RAM_DIS);
sky2_prefetch_init(hw, rxq, sky2->rx_le_map, RX_LE_SIZE - 1);
/* Tell chip about available buffers */
sky2_rx_update(sky2, rxq);
+
+ if (hw->chip_id == CHIP_ID_YUKON_EX ||
+ hw->chip_id == CHIP_ID_YUKON_SUPR) {
+ /*
+ * Disable flushing of non ASF packets;
+ * must be done after initializing the BMUs;
+ * drivers without ASF support should do this too, otherwise
+ * it may happen that they cannot run on ASF devices;
+ * remember that the MAC FIFO isn't reset during initialization.
+ */
+ sky2_write32(hw, SK_REG(sky2->port, RX_GMF_CTRL_T), RX_MACSEC_FLUSH_OFF);
+ }
+
+ if (hw->chip_id >= CHIP_ID_YUKON_SUPR) {
+ /* Enable RX Home Address & Routing Header checksum fix */
+ sky2_write16(hw, SK_REG(sky2->port, RX_GMF_FL_CTRL),
+ RX_IPV6_SA_MOB_ENA | RX_IPV6_DA_MOB_ENA);
+
+ /* Enable TX Home Address & Routing Header checksum fix */
+ sky2_write32(hw, Q_ADDR(txqaddr[sky2->port], Q_TEST),
+ TBMU_TEST_HOME_ADD_FIX_EN | TBMU_TEST_ROUTING_ADD_FIX_EN);
+ }
+
+
+
return 0;
nomem:
sky2_rx_clean(sky2);
sky2_write32(hw, Q_ADDR(txqaddr[port], Q_TEST), F_TX_CHK_AUTO_OFF);
/* Set almost empty threshold */
- if (hw->chip_id == CHIP_ID_YUKON_EC_U
- && hw->chip_rev == CHIP_REV_YU_EC_U_A0)
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U &&
+ hw->chip_rev == CHIP_REV_YU_EC_U_A0)
sky2_write16(hw, Q_ADDR(txqaddr[port], Q_AL), ECU_TXFF_LEV);
sky2_prefetch_init(hw, txqaddr[port], sky2->tx_le_map,
return count;
}
-static void sky2_tx_unmap(struct pci_dev *pdev,
- const struct tx_ring_info *re)
+static void sky2_tx_unmap(struct pci_dev *pdev, struct tx_ring_info *re)
{
if (re->flags & TX_MAP_SINGLE)
pci_unmap_single(pdev, pci_unmap_addr(re, mapaddr),
pci_unmap_page(pdev, pci_unmap_addr(re, mapaddr),
pci_unmap_len(re, maplen),
PCI_DMA_TODEVICE);
+ re->flags = 0;
}
/*
dev->stats.tx_packets++;
dev->stats.tx_bytes += skb->len;
+ re->skb = NULL;
dev_kfree_skb_any(skb);
sky2->tx_next = RING_NEXT(idx, sky2->tx_ring_size);
sky2->tx_cons = idx;
smp_mb();
- if (tx_avail(sky2) > MAX_SKB_TX_LE + 4)
+ /* Wake unless it's detached, and called e.g. from sky2_down() */
+ if (tx_avail(sky2) > MAX_SKB_TX_LE + 4 && netif_device_present(dev))
netif_wake_queue(dev);
}
sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET);
/* Workaround shared GMAC reset */
- if (!(hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0
- && port == 0 && hw->dev[1] && netif_running(hw->dev[1])))
+ if (!(hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0 &&
+ port == 0 && hw->dev[1] && netif_running(hw->dev[1])))
sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_SET);
sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET);
netif_carrier_off(sky2->netdev);
- /* Turn on link LED */
+ /* Turn off link LED */
sky2_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_OFF);
if (netif_msg_link(sky2))
sky2->flow_status = FC_TX;
}
- if (sky2->duplex == DUPLEX_HALF && sky2->speed < SPEED_1000
- && !(hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX))
+ if (sky2->duplex == DUPLEX_HALF && sky2->speed < SPEED_1000 &&
+ !(hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX))
sky2->flow_status = FC_NONE;
if (sky2->flow_status & FC_TX)
spin_unlock(&sky2->phy_lock);
}
+/* Special quick link interrupt (Yukon-2 Optima only) */
+static void sky2_qlink_intr(struct sky2_hw *hw)
+{
+ struct sky2_port *sky2 = netdev_priv(hw->dev[0]);
+ u32 imask;
+ u16 phy;
+
+ /* disable irq */
+ imask = sky2_read32(hw, B0_IMSK);
+ imask &= ~Y2_IS_PHY_QLNK;
+ sky2_write32(hw, B0_IMSK, imask);
+
+ /* reset PHY Link Detect */
+ phy = sky2_pci_read16(hw, PSM_CONFIG_REG4);
+ sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
+ sky2_pci_write16(hw, PSM_CONFIG_REG4, phy | 1);
+ sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
+
+ sky2_link_up(sky2);
+}
+
/* Transmit timeout is only called if we are running, carrier is up
* and tx queue is full (stopped).
*/
{
struct sk_buff *skb;
- skb = netdev_alloc_skb(sky2->netdev, length + 2);
+ skb = netdev_alloc_skb_ip_align(sky2->netdev, length);
if (likely(skb)) {
- skb_reserve(skb, 2);
pci_dma_sync_single_for_cpu(sky2->hw->pdev, re->data_addr,
length, PCI_DMA_FROMDEVICE);
skb_copy_from_linear_data(re->skb, skb->data, length);
if (status & Y2_IS_IRQ_PHY2)
sky2_phy_intr(hw, 1);
+ if (status & Y2_IS_PHY_QLNK)
+ sky2_qlink_intr(hw);
+
while ((idx = sky2_read16(hw, STAT_PUT_IDX)) != hw->st_idx) {
work_done += sky2_status_intr(hw, work_limit - work_done, idx);
case CHIP_ID_YUKON_EX:
case CHIP_ID_YUKON_SUPR:
case CHIP_ID_YUKON_UL_2:
+ case CHIP_ID_YUKON_OPT:
return 125;
case CHIP_ID_YUKON_FE:
| SKY2_HW_ADV_POWER_CTL;
break;
+ case CHIP_ID_YUKON_OPT:
+ hw->flags = SKY2_HW_GIGABIT
+ | SKY2_HW_NEW_LE
+ | SKY2_HW_ADV_POWER_CTL;
+ break;
+
default:
dev_err(&hw->pdev->dev, "unsupported chip type 0x%x\n",
hw->chip_id);
sky2_write16(hw, SK_REG(i, GMAC_CTRL),
GMC_BYP_MACSECRX_ON | GMC_BYP_MACSECTX_ON
| GMC_BYP_RETR_ON);
+
+ }
+
+ if (hw->chip_id == CHIP_ID_YUKON_SUPR && hw->chip_rev > CHIP_REV_YU_SU_B0) {
+ /* enable MACSec clock gating */
+ sky2_pci_write32(hw, PCI_DEV_REG3, P_CLK_MACSEC_DIS);
+ }
+
+ if (hw->chip_id == CHIP_ID_YUKON_OPT) {
+ u16 reg;
+ u32 msk;
+
+ if (hw->chip_rev == 0) {
+ /* disable PCI-E PHY power down (set PHY reg 0x80, bit 7 */
+ sky2_write32(hw, Y2_PEX_PHY_DATA, (0x80UL << 16) | (1 << 7));
+
+ /* set PHY Link Detect Timer to 1.1 second (11x 100ms) */
+ reg = 10;
+ } else {
+ /* set PHY Link Detect Timer to 0.4 second (4x 100ms) */
+ reg = 3;
+ }
+
+ reg <<= PSM_CONFIG_REG4_TIMER_PHY_LINK_DETECT_BASE;
+
+ /* reset PHY Link Detect */
+ sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
+ sky2_pci_write16(hw, PSM_CONFIG_REG4,
+ reg | PSM_CONFIG_REG4_RST_PHY_LINK_DETECT);
+ sky2_pci_write16(hw, PSM_CONFIG_REG4, reg);
+
+
+ /* enable PHY Quick Link */
+ msk = sky2_read32(hw, B0_IMSK);
+ msk |= Y2_IS_PHY_QLNK;
+ sky2_write32(hw, B0_IMSK, msk);
+
+ /* check if PSMv2 was running before */
+ reg = sky2_pci_read16(hw, PSM_CONFIG_REG3);
+ if (reg & PCI_EXP_LNKCTL_ASPMC) {
+ int cap = pci_find_capability(pdev, PCI_CAP_ID_EXP);
+ /* restore the PCIe Link Control register */
+ sky2_pci_write16(hw, cap + PCI_EXP_LNKCTL, reg);
+ }
+ sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
+
+ /* re-enable PEX PM in PEX PHY debug reg. 8 (clear bit 12) */
+ sky2_write32(hw, Y2_PEX_PHY_DATA, PEX_DB_ACCESS | (0x08UL << 16));
}
/* Clear I2C IRQ noise */
return sky2_is_copper(hw) ? (WAKE_PHY | WAKE_MAGIC) : 0;
}
+static void sky2_hw_set_wol(struct sky2_hw *hw)
+{
+ int wol = 0;
+ int i;
+
+ for (i = 0; i < hw->ports; i++) {
+ struct net_device *dev = hw->dev[i];
+ struct sky2_port *sky2 = netdev_priv(dev);
+
+ if (sky2->wol)
+ wol = 1;
+ }
+
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U ||
+ hw->chip_id == CHIP_ID_YUKON_EX ||
+ hw->chip_id == CHIP_ID_YUKON_FE_P)
+ sky2_write32(hw, B0_CTST, wol ? Y2_HW_WOL_ON : Y2_HW_WOL_OFF);
+
+ device_set_wakeup_enable(&hw->pdev->dev, wol);
+}
+
static void sky2_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
{
const struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
- if ((wol->wolopts & ~sky2_wol_supported(sky2->hw))
- || !device_can_wakeup(&hw->pdev->dev))
+ if ((wol->wolopts & ~sky2_wol_supported(sky2->hw)) ||
+ !device_can_wakeup(&hw->pdev->dev))
return -EOPNOTSUPP;
sky2->wol = wol->wolopts;
- if (hw->chip_id == CHIP_ID_YUKON_EC_U ||
- hw->chip_id == CHIP_ID_YUKON_EX ||
- hw->chip_id == CHIP_ID_YUKON_FE_P)
- sky2_write32(hw, B0_CTST, sky2->wol
- ? Y2_HW_WOL_ON : Y2_HW_WOL_OFF);
-
- device_set_wakeup_enable(&hw->pdev->dev, sky2->wol);
+ sky2_hw_set_wol(hw);
if (!netif_running(dev))
sky2_wol_init(sky2);
"FE+", /* 0xb8 */
"Supreme", /* 0xb9 */
"UL 2", /* 0xba */
+ "Unknown", /* 0xbb */
+ "Optima", /* 0xbc */
};
- if (chipid >= CHIP_ID_YUKON_XL && chipid < CHIP_ID_YUKON_UL_2)
+ if (chipid >= CHIP_ID_YUKON_XL && chipid <= CHIP_ID_YUKON_OPT)
strncpy(buf, name[chipid - CHIP_ID_YUKON_XL], sz);
else
snprintf(buf, sz, "(chip %#x)", chipid);
INIT_WORK(&hw->restart_work, sky2_restart);
pci_set_drvdata(pdev, hw);
+ pdev->d3_delay = 150;
return 0;
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff