/*
- * Definitions for the new Marvell Yukon / SysKonenct driver.
+ * Definitions for the new Marvell Yukon / SysKonnect driver.
*/
#ifndef _SKGE_H
#define _SKGE_H
/* PCI config registers */
#define PCI_DEV_REG1 0x40
-#define PCI_DEV_REG2 0x44
-#ifndef PCI_VPD
-#define PCI_VPD 0x50
-#endif
-
-/* PCI_OUR_REG_2 32 bit Our Register 2 */
-enum {
- PCI_VPD_WR_THR = 0xff<<24, /* Bit 31..24: VPD Write Threshold */
- PCI_DEV_SEL = 0x7f<<17, /* Bit 23..17: EEPROM Device Select */
- PCI_VPD_ROM_SZ = 7 <<14, /* Bit 16..14: VPD ROM Size */
- /* Bit 13..12: reserved */
- PCI_EN_DUMMY_RD = 1<<3, /* Enable Dummy Read */
- PCI_REV_DESC = 1<<2, /* Reverse Desc. Bytes */
- PCI_USEDATA64 = 1<<0, /* Use 64Bit Data bus ext */
-};
-
-/* PCI_VPD_ADR_REG 16 bit VPD Address Register */
-enum {
- PCI_VPD_FLAG = 1<<15, /* starts VPD rd/wr cycle */
- PCI_VPD_ADR_MSK =0x7fffL, /* Bit 14.. 0: VPD Address Mask */
- VPD_RES_ID = 0x82,
- VPD_RES_READ = 0x90,
- VPD_RES_WRITE = 0x81,
- VPD_RES_END = 0x78,
-};
+#define PCI_PHY_COMA 0x8000000
+#define PCI_VIO 0x2000000
+#define PCI_DEV_REG2 0x44
+#define PCI_VPD_ROM_SZ 7L<<14 /* VPD ROM size 0=256, 1=512, ... */
+#define PCI_REV_DESC 1<<2 /* Reverse Descriptor bytes */
#define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \
PCI_STATUS_SIG_SYSTEM_ERROR | \
PCI_STATUS_REC_TARGET_ABORT | \
PCI_STATUS_PARITY)
-
enum csr_regs {
B0_RAP = 0x0000,
B0_CTST = 0x0004,
IS_XA2_F = 1<<1, /* Q_XA2 End of Frame */
IS_XA2_C = 1<<0, /* Q_XA2 Encoding Error */
- IS_PORT_1 = IS_XA1_F| IS_R1_F| IS_MAC1,
- IS_PORT_2 = IS_XA2_F| IS_R2_F| IS_MAC2,
+ IS_TO_PORT1 = IS_PA_TO_RX1 | IS_PA_TO_TX1,
+ IS_TO_PORT2 = IS_PA_TO_RX2 | IS_PA_TO_TX2,
+
+ IS_PORT_1 = IS_XA1_F| IS_R1_F | IS_TO_PORT1 | IS_MAC1,
+ IS_PORT_2 = IS_XA2_F| IS_R2_F | IS_TO_PORT2 | IS_MAC2,
};
/* B2_IRQM_HWE_MSK 32 bit IRQ Moderation HW Error Mask */
enum {
- IS_ERR_MSK = 0x00003fff,/* All Error bits */
-
IS_IRQ_TIST_OV = 1<<13, /* Time Stamp Timer Overflow (YUKON only) */
IS_IRQ_SENSOR = 1<<12, /* IRQ from Sensor (YUKON only) */
IS_IRQ_MST_ERR = 1<<11, /* IRQ master error detected */
IS_M2_PAR_ERR = 1<<2, /* MAC 2 Parity Error */
IS_R1_PAR_ERR = 1<<1, /* Queue R1 Parity Error */
IS_R2_PAR_ERR = 1<<0, /* Queue R2 Parity Error */
+
+ IS_ERR_MSK = IS_IRQ_MST_ERR | IS_IRQ_STAT
+ | IS_RAM_RD_PAR | IS_RAM_WR_PAR
+ | IS_M1_PAR_ERR | IS_M2_PAR_ERR
+ | IS_R1_PAR_ERR | IS_R2_PAR_ERR,
};
/* B2_TST_CTRL1 8 bit Test Control Register 1 */
CHIP_REV_YU_LITE_A3 = 7, /* Chip Rev. for YUKON-Lite A3 */
};
-/* B2_LD_TEST 8 bit EPROM loader test register */
-enum {
- LD_T_ON = 1<<3, /* Loader Test mode on */
- LD_T_OFF = 1<<2, /* Loader Test mode off */
- LD_T_STEP = 1<<1, /* Decrement FPROM addr. Counter */
- LD_START = 1<<0, /* Start loading FPROM */
-};
-
/* B2_TI_CTRL 8 bit Timer control */
/* B2_IRQM_CTRL 8 bit IRQ Moderation Timer Control */
enum {
TIM_T_STEP = 1<<0, /* Test step */
};
-/* B28_DPT_INI 32 bit Descriptor Poll Timer Init Val */
-/* B28_DPT_VAL 32 bit Descriptor Poll Timer Curr Val */
-/* B28_DPT_CTRL 8 bit Descriptor Poll Timer Ctrl Reg */
-enum {
- DPT_MSK = 0x00ffffffL, /* Bit 23.. 0: Desc Poll Timer Bits */
-
- DPT_START = 1<<1, /* Start Descriptor Poll Timer */
- DPT_STOP = 1<<0, /* Stop Descriptor Poll Timer */
-};
-
/* B2_GP_IO 32 bit General Purpose I/O Register */
enum {
GP_DIR_9 = 1<<25, /* IO_9 direct, 0=In/1=Out */
GP_IO_0 = 1<<0, /* IO_0 pin */
};
-/* Rx/Tx Path related Arbiter Test Registers */
-/* B3_MA_TO_TEST 16 bit MAC Arbiter Timeout Test Reg */
-/* B3_MA_RC_TEST 16 bit MAC Arbiter Recovery Test Reg */
-/* B3_PA_TEST 16 bit Packet Arbiter Test Register */
-/* Bit 15, 11, 7, and 3 are reserved in B3_PA_TEST */
-enum {
- TX2_T_EV = 1<<15,/* TX2 Timeout/Recv Event occured */
- TX2_T_ON = 1<<14,/* TX2 Timeout/Recv Timer Test On */
- TX2_T_OFF = 1<<13,/* TX2 Timeout/Recv Timer Tst Off */
- TX2_T_STEP = 1<<12,/* TX2 Timeout/Recv Timer Step */
- TX1_T_EV = 1<<11,/* TX1 Timeout/Recv Event occured */
- TX1_T_ON = 1<<10,/* TX1 Timeout/Recv Timer Test On */
- TX1_T_OFF = 1<<9, /* TX1 Timeout/Recv Timer Tst Off */
- TX1_T_STEP = 1<<8, /* TX1 Timeout/Recv Timer Step */
- RX2_T_EV = 1<<7, /* RX2 Timeout/Recv Event occured */
- RX2_T_ON = 1<<6, /* RX2 Timeout/Recv Timer Test On */
- RX2_T_OFF = 1<<5, /* RX2 Timeout/Recv Timer Tst Off */
- RX2_T_STEP = 1<<4, /* RX2 Timeout/Recv Timer Step */
- RX1_T_EV = 1<<3, /* RX1 Timeout/Recv Event occured */
- RX1_T_ON = 1<<2, /* RX1 Timeout/Recv Timer Test On */
- RX1_T_OFF = 1<<1, /* RX1 Timeout/Recv Timer Tst Off */
- RX1_T_STEP = 1<<0, /* RX1 Timeout/Recv Timer Step */
-};
-
/* Descriptor Bit Definition */
/* TxCtrl Transmit Buffer Control Field */
/* RxCtrl Receive Buffer Control Field */
RI_RST_SET = 1<<0, /* Set RAM Interface Reset */
};
-/* B3_RI_TEST 8 bit RAM Iface Test Register */
-enum {
- RI_T_EV = 1<<3, /* Timeout Event occured */
- RI_T_ON = 1<<2, /* Timeout Timer Test On */
- RI_T_OFF = 1<<1, /* Timeout Timer Test Off */
- RI_T_STEP = 1<<0, /* Timeout Timer Step */
-};
-
/* MAC Arbiter Registers */
/* B3_MA_TO_CTRL 16 bit MAC Arbiter Timeout Ctrl Reg */
enum {
#define SK_PKT_TO_MAX 0xffff /* Maximum value */
#define SK_RI_TO_53 36 /* RAM interface timeout */
-
-/* B3_MA_RC_CTRL 16 bit MAC Arbiter Recovery Ctrl Reg */
-enum {
- MA_ENA_REC_TX2 = 1<<7, /* Enable Recovery Timer TX2 */
- MA_DIS_REC_TX2 = 1<<6, /* Disable Recovery Timer TX2 */
- MA_ENA_REC_TX1 = 1<<5, /* Enable Recovery Timer TX1 */
- MA_DIS_REC_TX1 = 1<<4, /* Disable Recovery Timer TX1 */
- MA_ENA_REC_RX2 = 1<<3, /* Enable Recovery Timer RX2 */
- MA_DIS_REC_RX2 = 1<<2, /* Disable Recovery Timer RX2 */
- MA_ENA_REC_RX1 = 1<<1, /* Enable Recovery Timer RX1 */
- MA_DIS_REC_RX1 = 1<<0, /* Disable Recovery Timer RX1 */
-};
-
/* Packet Arbiter Registers */
/* B3_PA_CTRL 16 bit Packet Arbiter Ctrl Register */
enum {
- PA_CLR_TO_TX2 = 1<<13, /* Clear IRQ Packet Timeout TX2 */
- PA_CLR_TO_TX1 = 1<<12, /* Clear IRQ Packet Timeout TX1 */
- PA_CLR_TO_RX2 = 1<<11, /* Clear IRQ Packet Timeout RX2 */
- PA_CLR_TO_RX1 = 1<<10, /* Clear IRQ Packet Timeout RX1 */
+ PA_CLR_TO_TX2 = 1<<13,/* Clear IRQ Packet Timeout TX2 */
+ PA_CLR_TO_TX1 = 1<<12,/* Clear IRQ Packet Timeout TX1 */
+ PA_CLR_TO_RX2 = 1<<11,/* Clear IRQ Packet Timeout RX2 */
+ PA_CLR_TO_RX1 = 1<<10,/* Clear IRQ Packet Timeout RX1 */
PA_ENA_TO_TX2 = 1<<9, /* Enable Timeout Timer TX2 */
PA_DIS_TO_TX2 = 1<<8, /* Disable Timeout Timer TX2 */
PA_ENA_TO_TX1 = 1<<7, /* Enable Timeout Timer TX1 */
PA_ENA_TO_TX1 | PA_ENA_TO_TX2)
-/* Transmit Arbiter Registers MAC 1 and 2, use MR_ADDR() to access */
+/* Transmit Arbiter Registers MAC 1 and 2, use SK_REG() to access */
/* TXA_ITI_INI 32 bit Tx Arb Interval Timer Init Val */
/* TXA_ITI_VAL 32 bit Tx Arb Interval Timer Value */
/* TXA_LIM_INI 32 bit Tx Arb Limit Counter Init Val */
/*
* Bank 4 - 5
*/
-/* Transmit Arbiter Registers MAC 1 and 2, use MR_ADDR() to access */
+/* Transmit Arbiter Registers MAC 1 and 2, use SK_REG() to access */
enum {
TXA_ITI_INI = 0x0200,/* 32 bit Tx Arb Interval Timer Init Val*/
TXA_ITI_VAL = 0x0204,/* 32 bit Tx Arb Interval Timer Value */
/* Queue Register Offsets, use Q_ADDR() to access */
enum {
- B8_Q_REGS = 0x0400, /* base of Queue registers */
+ B8_Q_REGS = 0x0400, /* base of Queue registers */
Q_D = 0x00, /* 8*32 bit Current Descriptor */
Q_DA_L = 0x20, /* 32 bit Current Descriptor Address Low dWord */
Q_DA_H = 0x24, /* 32 bit Current Descriptor Address High dWord */
Q_T2 = 0x40, /* 32 bit Test Register 2 */
Q_T3 = 0x44, /* 32 bit Test Register 3 */
-/* Yukon-2 */
- Q_DONE = 0x24, /* 16 bit Done Index (Yukon-2 only) */
- Q_WM = 0x40, /* 16 bit FIFO Watermark */
- Q_AL = 0x42, /* 8 bit FIFO Alignment */
- Q_RSP = 0x44, /* 16 bit FIFO Read Shadow Pointer */
- Q_RSL = 0x46, /* 8 bit FIFO Read Shadow Level */
- Q_RP = 0x48, /* 8 bit FIFO Read Pointer */
- Q_RL = 0x4a, /* 8 bit FIFO Read Level */
- Q_WP = 0x4c, /* 8 bit FIFO Write Pointer */
- Q_WSP = 0x4d, /* 8 bit FIFO Write Shadow Pointer */
- Q_WL = 0x4e, /* 8 bit FIFO Write Level */
- Q_WSL = 0x4f, /* 8 bit FIFO Write Shadow Level */
};
#define Q_ADDR(reg, offs) (B8_Q_REGS + (reg) + (offs))
/* RAM Buffer Register Offsets */
enum {
- RB_START = 0x00,/* 32 bit RAM Buffer Start Address */
+ RB_START= 0x00,/* 32 bit RAM Buffer Start Address */
RB_END = 0x04,/* 32 bit RAM Buffer End Address */
RB_WP = 0x08,/* 32 bit RAM Buffer Write Pointer */
RB_RP = 0x0c,/* 32 bit RAM Buffer Read Pointer */
- RB_RX_UTPP = 0x10,/* 32 bit Rx Upper Threshold, Pause Packet */
- RB_RX_LTPP = 0x14,/* 32 bit Rx Lower Threshold, Pause Packet */
- RB_RX_UTHP = 0x18,/* 32 bit Rx Upper Threshold, High Prio */
- RB_RX_LTHP = 0x1c,/* 32 bit Rx Lower Threshold, High Prio */
+ RB_RX_UTPP= 0x10,/* 32 bit Rx Upper Threshold, Pause Packet */
+ RB_RX_LTPP= 0x14,/* 32 bit Rx Lower Threshold, Pause Packet */
+ RB_RX_UTHP= 0x18,/* 32 bit Rx Upper Threshold, High Prio */
+ RB_RX_LTHP= 0x1c,/* 32 bit Rx Lower Threshold, High Prio */
/* 0x10 - 0x1f: reserved at Tx RAM Buffer Registers */
RB_PC = 0x20,/* 32 bit RAM Buffer Packet Counter */
RB_LEV = 0x24,/* 32 bit RAM Buffer Level Register */
enum {
PHY_ADDR_XMAC = 0<<8,
PHY_ADDR_BCOM = 1<<8,
- PHY_ADDR_LONE = 3<<8,
- PHY_ADDR_NAT = 0<<8,
+
/* GPHY address (bits 15..11 of SMI control reg) */
PHY_ADDR_MARV = 0,
};
-#define RB_ADDR(offs, queue) (B16_RAM_REGS + (queue) + (offs))
+#define RB_ADDR(offs, queue) ((u16)B16_RAM_REGS + (u16)(queue) + (offs))
/* Receive MAC FIFO, Receive LED, and Link_Sync regs (GENESIS only) */
enum {
MFF_DIS_TIST = 1<<2, /* Disable Time Stamp Gener */
MFF_CLR_INTIST = 1<<1, /* Clear IRQ No Time Stamp */
MFF_CLR_INSTAT = 1<<0, /* Clear IRQ No Status */
-#define MFF_RX_CTRL_DEF MFF_ENA_TIM_PAT
+ MFF_RX_CTRL_DEF = MFF_ENA_TIM_PAT,
};
/* TX_MFF_CTRL1 16 bit Transmit MAC FIFO Control Reg 1 */
enum {
- MFF_CLR_PERR = 1<<15, /* Clear Parity Error IRQ */
- /* Bit 14: reserved */
- MFF_ENA_PKT_REC = 1<<13, /* Enable Packet Recovery */
- MFF_DIS_PKT_REC = 1<<12, /* Disable Packet Recovery */
+ MFF_CLR_PERR = 1<<15, /* Clear Parity Error IRQ */
+
+ MFF_ENA_PKT_REC = 1<<13, /* Enable Packet Recovery */
+ MFF_DIS_PKT_REC = 1<<12, /* Disable Packet Recovery */
MFF_ENA_W4E = 1<<7, /* Enable Wait for Empty */
MFF_DIS_W4E = 1<<6, /* Disable Wait for Empty */
MFF_DIS_LOOPB = 1<<2, /* Disable Loopback */
MFF_CLR_MAC_RST = 1<<1, /* Clear XMAC Reset */
MFF_SET_MAC_RST = 1<<0, /* Set XMAC Reset */
+
+ MFF_TX_CTRL_DEF = MFF_ENA_PKT_REC | (u16) MFF_ENA_TIM_PAT | MFF_ENA_FLUSH,
};
-#define MFF_TX_CTRL_DEF (MFF_ENA_PKT_REC | MFF_ENA_TIM_PAT | MFF_ENA_FLUSH)
/* RX_MFF_TST2 8 bit Receive MAC FIFO Test Register 2 */
/* TX_MFF_TST2 8 bit Transmit MAC FIFO Test Register 2 */
LED_OFF = 1<<0, /* switch LED off */
};
-/* Receive GMAC FIFO (YUKON and Yukon-2) */
+/* Receive GMAC FIFO (YUKON) */
enum {
RX_GMF_EA = 0x0c40,/* 32 bit Rx GMAC FIFO End Address */
RX_GMF_AF_THR = 0x0c44,/* 32 bit Rx GMAC FIFO Almost Full Thresh. */
RX_GMF_CTRL_T = 0x0c48,/* 32 bit Rx GMAC FIFO Control/Test */
RX_GMF_FL_MSK = 0x0c4c,/* 32 bit Rx GMAC FIFO Flush Mask */
RX_GMF_FL_THR = 0x0c50,/* 32 bit Rx GMAC FIFO Flush Threshold */
- RX_GMF_TR_THR = 0x0c54,/* 32 bit Rx Truncation Threshold (Yukon-2) */
-
- RX_GMF_VLAN = 0x0c5c,/* 32 bit Rx VLAN Type Register (Yukon-2) */
RX_GMF_WP = 0x0c60,/* 32 bit Rx GMAC FIFO Write Pointer */
-
RX_GMF_WLEV = 0x0c68,/* 32 bit Rx GMAC FIFO Write Level */
-
RX_GMF_RP = 0x0c70,/* 32 bit Rx GMAC FIFO Read Pointer */
-
RX_GMF_RLEV = 0x0c78,/* 32 bit Rx GMAC FIFO Read Level */
};
GMAC_TI_ST_TST = 0x0e1a,/* 8 bit Time Stamp Timer Test Reg */
};
-/* Status BMU Registers (Yukon-2 only)*/
-enum {
- STAT_CTRL = 0x0e80,/* 32 bit Status BMU Control Reg */
- STAT_LAST_IDX = 0x0e84,/* 16 bit Status BMU Last Index */
- /* 0x0e85 - 0x0e86: reserved */
- STAT_LIST_ADDR_LO = 0x0e88,/* 32 bit Status List Start Addr (low) */
- STAT_LIST_ADDR_HI = 0x0e8c,/* 32 bit Status List Start Addr (high) */
- STAT_TXA1_RIDX = 0x0e90,/* 16 bit Status TxA1 Report Index Reg */
- STAT_TXS1_RIDX = 0x0e92,/* 16 bit Status TxS1 Report Index Reg */
- STAT_TXA2_RIDX = 0x0e94,/* 16 bit Status TxA2 Report Index Reg */
- STAT_TXS2_RIDX = 0x0e96,/* 16 bit Status TxS2 Report Index Reg */
- STAT_TX_IDX_TH = 0x0e98,/* 16 bit Status Tx Index Threshold Reg */
- STAT_PUT_IDX = 0x0e9c,/* 16 bit Status Put Index Reg */
-
-/* FIFO Control/Status Registers (Yukon-2 only)*/
- STAT_FIFO_WP = 0x0ea0,/* 8 bit Status FIFO Write Pointer Reg */
- STAT_FIFO_RP = 0x0ea4,/* 8 bit Status FIFO Read Pointer Reg */
- STAT_FIFO_RSP = 0x0ea6,/* 8 bit Status FIFO Read Shadow Ptr */
- STAT_FIFO_LEVEL = 0x0ea8,/* 8 bit Status FIFO Level Reg */
- STAT_FIFO_SHLVL = 0x0eaa,/* 8 bit Status FIFO Shadow Level Reg */
- STAT_FIFO_WM = 0x0eac,/* 8 bit Status FIFO Watermark Reg */
- STAT_FIFO_ISR_WM = 0x0ead,/* 8 bit Status FIFO ISR Watermark Reg */
-
-/* Level and ISR Timer Registers (Yukon-2 only)*/
- STAT_LEV_TIMER_INI = 0x0eb0,/* 32 bit Level Timer Init. Value Reg */
- STAT_LEV_TIMER_CNT = 0x0eb4,/* 32 bit Level Timer Counter Reg */
- STAT_LEV_TIMER_CTRL = 0x0eb8,/* 8 bit Level Timer Control Reg */
- STAT_LEV_TIMER_TEST = 0x0eb9,/* 8 bit Level Timer Test Reg */
- STAT_TX_TIMER_INI = 0x0ec0,/* 32 bit Tx Timer Init. Value Reg */
- STAT_TX_TIMER_CNT = 0x0ec4,/* 32 bit Tx Timer Counter Reg */
- STAT_TX_TIMER_CTRL = 0x0ec8,/* 8 bit Tx Timer Control Reg */
- STAT_TX_TIMER_TEST = 0x0ec9,/* 8 bit Tx Timer Test Reg */
- STAT_ISR_TIMER_INI = 0x0ed0,/* 32 bit ISR Timer Init. Value Reg */
- STAT_ISR_TIMER_CNT = 0x0ed4,/* 32 bit ISR Timer Counter Reg */
- STAT_ISR_TIMER_CTRL = 0x0ed8,/* 8 bit ISR Timer Control Reg */
- STAT_ISR_TIMER_TEST = 0x0ed9,/* 8 bit ISR Timer Test Reg */
-
- ST_LAST_IDX_MASK = 0x007f,/* Last Index Mask */
- ST_TXRP_IDX_MASK = 0x0fff,/* Tx Report Index Mask */
- ST_TXTH_IDX_MASK = 0x0fff,/* Tx Threshold Index Mask */
- ST_WM_IDX_MASK = 0x3f,/* FIFO Watermark Index Mask */
-};
enum {
LINKLED_OFF = 0x01,
LINKLED_BLINK_OFF = 0x10,
LINKLED_BLINK_ON = 0x20,
};
-
+
/* GMAC and GPHY Control Registers (YUKON only) */
enum {
GMAC_CTRL = 0x0f00,/* 32 bit GMAC Control Reg */
WOL_MATCH_CTL = 0x0f22,/* 8 bit WOL Match Control Reg */
WOL_MATCH_RES = 0x0f23,/* 8 bit WOL Match Result Reg */
WOL_MAC_ADDR = 0x0f24,/* 32 bit WOL MAC Address */
- WOL_PATT_PME = 0x0f2a,/* 8 bit WOL PME Match Enable (Yukon-2) */
- WOL_PATT_ASFM = 0x0f2b,/* 8 bit WOL ASF Match Enable (Yukon-2) */
WOL_PATT_RPTR = 0x0f2c,/* 8 bit WOL Pattern Read Pointer */
/* WOL Pattern Length Registers (YUKON only) */
WOL_PATT_CNT_0 = 0x0f38,/* 32 bit WOL Pattern Counter 3..0 */
WOL_PATT_CNT_4 = 0x0f3c,/* 24 bit WOL Pattern Counter 6..4 */
};
+#define WOL_REGS(port, x) (x + (port)*0x80)
enum {
WOL_PATT_RAM_1 = 0x1000,/* WOL Pattern RAM Link 1 */
WOL_PATT_RAM_2 = 0x1400,/* WOL Pattern RAM Link 2 */
};
+#define WOL_PATT_RAM_BASE(port) (WOL_PATT_RAM_1 + (port)*0x400)
enum {
BASE_XMAC_1 = 0x2000,/* XMAC 1 registers */
*/
enum {
XMR_FS_LEN = 0x3fff<<18, /* Bit 31..18: Rx Frame Length */
+ XMR_FS_LEN_SHIFT = 18,
XMR_FS_2L_VLAN = 1<<17, /* Bit 17: tagged wh 2Lev VLAN ID*/
XMR_FS_1_VLAN = 1<<16, /* Bit 16: tagged wh 1ev VLAN ID*/
XMR_FS_BC = 1<<15, /* Bit 15: Broadcast Frame */
PHY_XMAC_AUNE_ADV = 0x04,/* 16 bit r/w Auto-Neg. Advertisement */
PHY_XMAC_AUNE_LP = 0x05,/* 16 bit r/o Link Partner Abi Reg */
PHY_XMAC_AUNE_EXP = 0x06,/* 16 bit r/o Auto-Neg. Expansion Reg */
- PHY_XMAC_NEPG = 0x07,/* 16 bit r/w Next Page Register */
+ PHY_XMAC_NEPG = 0x07,/* 16 bit r/w Next Page Register */
PHY_XMAC_NEPG_LP = 0x08,/* 16 bit r/o Next Page Link Partner */
PHY_XMAC_EXT_STAT = 0x0f,/* 16 bit r/o Ext Status Register */
PHY_MARV_FE_SPEC_2 = 0x1c,/* 16 bit r/w Specific Control Reg. 2 */
};
-/* Level One-PHY Registers, indirect addressed over XMAC */
-enum {
- PHY_LONE_CTRL = 0x00,/* 16 bit r/w PHY Control Register */
- PHY_LONE_STAT = 0x01,/* 16 bit r/o PHY Status Register */
- PHY_LONE_ID0 = 0x02,/* 16 bit r/o PHY ID0 Register */
- PHY_LONE_ID1 = 0x03,/* 16 bit r/o PHY ID1 Register */
- PHY_LONE_AUNE_ADV = 0x04,/* 16 bit r/w Auto-Neg. Advertisement */
- PHY_LONE_AUNE_LP = 0x05,/* 16 bit r/o Link Part Ability Reg */
- PHY_LONE_AUNE_EXP = 0x06,/* 16 bit r/o Auto-Neg. Expansion Reg */
- PHY_LONE_NEPG = 0x07,/* 16 bit r/w Next Page Register */
- PHY_LONE_NEPG_LP = 0x08,/* 16 bit r/o Next Page Link Partner */
- /* Level One-specific registers */
- PHY_LONE_1000T_CTRL = 0x09,/* 16 bit r/w 1000Base-T Control Reg */
- PHY_LONE_1000T_STAT = 0x0a,/* 16 bit r/o 1000Base-T Status Reg */
- PHY_LONE_EXT_STAT = 0x0f,/* 16 bit r/o Extended Status Reg */
- PHY_LONE_PORT_CFG = 0x10,/* 16 bit r/w Port Configuration Reg*/
- PHY_LONE_Q_STAT = 0x11,/* 16 bit r/o Quick Status Reg */
- PHY_LONE_INT_ENAB = 0x12,/* 16 bit r/w Interrupt Enable Reg */
- PHY_LONE_INT_STAT = 0x13,/* 16 bit r/o Interrupt Status Reg */
- PHY_LONE_LED_CFG = 0x14,/* 16 bit r/w LED Configuration Reg */
- PHY_LONE_PORT_CTRL = 0x15,/* 16 bit r/w Port Control Reg */
- PHY_LONE_CIM = 0x16,/* 16 bit r/o CIM Reg */
-};
-
-/* National-PHY Registers, indirect addressed over XMAC */
-enum {
- PHY_NAT_CTRL = 0x00,/* 16 bit r/w PHY Control Register */
- PHY_NAT_STAT = 0x01,/* 16 bit r/w PHY Status Register */
- PHY_NAT_ID0 = 0x02,/* 16 bit r/o PHY ID0 Register */
- PHY_NAT_ID1 = 0x03,/* 16 bit r/o PHY ID1 Register */
- PHY_NAT_AUNE_ADV = 0x04,/* 16 bit r/w Auto-Neg. Advertisement */
- PHY_NAT_AUNE_LP = 0x05,/* 16 bit r/o Link Partner Ability Reg */
- PHY_NAT_AUNE_EXP = 0x06,/* 16 bit r/o Auto-Neg. Expansion Reg */
- PHY_NAT_NEPG = 0x07,/* 16 bit r/w Next Page Register */
- PHY_NAT_NEPG_LP = 0x08,/* 16 bit r/o Next Page Link Partner Reg */
- /* National-specific registers */
- PHY_NAT_1000T_CTRL = 0x09,/* 16 bit r/w 1000Base-T Control Reg */
- PHY_NAT_1000T_STAT = 0x0a,/* 16 bit r/o 1000Base-T Status Reg */
- PHY_NAT_EXT_STAT = 0x0f,/* 16 bit r/o Extended Status Register */
- PHY_NAT_EXT_CTRL1 = 0x10,/* 16 bit r/o Extended Control Reg1 */
- PHY_NAT_Q_STAT1 = 0x11,/* 16 bit r/o Quick Status Reg1 */
- PHY_NAT_10B_OP = 0x12,/* 16 bit r/o 10Base-T Operations Reg */
- PHY_NAT_EXT_CTRL2 = 0x13,/* 16 bit r/o Extended Control Reg1 */
- PHY_NAT_Q_STAT2 = 0x14,/* 16 bit r/o Quick Status Reg2 */
-
- PHY_NAT_PHY_ADDR = 0x19,/* 16 bit r/o PHY Address Register */
-};
-
enum {
PHY_CT_RESET = 1<<15, /* Bit 15: (sc) clear all PHY related regs */
PHY_CT_LOOP = 1<<14, /* Bit 14: enable Loopback over PHY */
PHY_MARV_ID1_Y2 = 0x0C91, /* Yukon-2 (PHY 88E1112) */
};
+/* Advertisement register bits */
enum {
PHY_AN_NXT_PG = 1<<15, /* Bit 15: Request Next Page */
+ PHY_AN_ACK = 1<<14, /* Bit 14: (ro) Acknowledge Received */
+ PHY_AN_RF = 1<<13, /* Bit 13: Remote Fault Bits */
+
+ PHY_AN_PAUSE_ASYM = 1<<11,/* Bit 11: Try for asymmetric */
+ PHY_AN_PAUSE_CAP = 1<<10, /* Bit 10: Try for pause */
+ PHY_AN_100BASE4 = 1<<9, /* Bit 9: Try for 100mbps 4k packets */
+ PHY_AN_100FULL = 1<<8, /* Bit 8: Try for 100mbps full-duplex */
+ PHY_AN_100HALF = 1<<7, /* Bit 7: Try for 100mbps half-duplex */
+ PHY_AN_10FULL = 1<<6, /* Bit 6: Try for 10mbps full-duplex */
+ PHY_AN_10HALF = 1<<5, /* Bit 5: Try for 10mbps half-duplex */
+ PHY_AN_CSMA = 1<<0, /* Bit 0: Only selector supported */
+ PHY_AN_SEL = 0x1f, /* Bit 4..0: Selector Field, 00001=Ethernet*/
+ PHY_AN_FULL = PHY_AN_100FULL | PHY_AN_10FULL | PHY_AN_CSMA,
+ PHY_AN_ALL = PHY_AN_10HALF | PHY_AN_10FULL |
+ PHY_AN_100HALF | PHY_AN_100FULL,
+};
+
+/* Xmac Specific */
+enum {
+ PHY_X_AN_NXT_PG = 1<<15, /* Bit 15: Request Next Page */
PHY_X_AN_ACK = 1<<14, /* Bit 14: (ro) Acknowledge Received */
PHY_X_AN_RFB = 3<<12,/* Bit 13..12: Remote Fault Bits */
PHY_X_AN_FD = 1<<5, /* Bit 5: Full Duplex */
};
+/* Pause Bits (PHY_X_AN_PAUSE and PHY_X_RS_PAUSE) encoding */
enum {
- PHY_B_AN_RF = 1<<13, /* Bit 13: Remote Fault */
-
- PHY_B_AN_ASP = 1<<11, /* Bit 11: Asymmetric Pause */
- PHY_B_AN_PC = 1<<10, /* Bit 10: Pause Capable */
- PHY_B_AN_SEL = 0x1f, /* Bit 4..0: Selector Field, 00001=Ethernet*/
-};
-
-enum {
- PHY_L_AN_RF = 1<<13, /* Bit 13: Remote Fault */
- /* Bit 12: reserved */
- PHY_L_AN_ASP = 1<<11, /* Bit 11: Asymmetric Pause */
- PHY_L_AN_PC = 1<<10, /* Bit 10: Pause Capable */
-
- PHY_L_AN_SEL = 0x1f, /* Bit 4..0: Selector Field, 00001=Ethernet*/
-};
-
-/* PHY_NAT_AUNE_ADV 16 bit r/w Auto-Negotiation Advertisement */
-/* PHY_NAT_AUNE_LP 16 bit r/o Link Partner Ability Reg *****/
-/* PHY_AN_NXT_PG (see XMAC) Bit 15: Request Next Page */
-enum {
- PHY_N_AN_RF = 1<<13, /* Bit 13: Remote Fault */
-
- PHY_N_AN_100F = 1<<11, /* Bit 11: 100Base-T2 FD Support */
- PHY_N_AN_100H = 1<<10, /* Bit 10: 100Base-T2 HD Support */
-
- PHY_N_AN_SEL = 0x1f, /* Bit 4..0: Selector Field, 00001=Ethernet*/
-};
-
-/* field type definition for PHY_x_AN_SEL */
-enum {
- PHY_SEL_TYPE = 1, /* 00001 = Ethernet */
-};
-
-enum {
- PHY_ANE_LP_NP = 1<<3, /* Bit 3: Link Partner can Next Page */
- PHY_ANE_LOC_NP = 1<<2, /* Bit 2: Local PHY can Next Page */
- PHY_ANE_RX_PG = 1<<1, /* Bit 1: Page Received */
-};
-
-enum {
- PHY_ANE_PAR_DF = 1<<4, /* Bit 4: Parallel Detection Fault */
-
- PHY_ANE_LP_CAP = 1<<0, /* Bit 0: Link Partner Auto-Neg. Cap. */
+ PHY_X_P_NO_PAUSE= 0<<7,/* Bit 8..7: no Pause Mode */
+ PHY_X_P_SYM_MD = 1<<7, /* Bit 8..7: symmetric Pause Mode */
+ PHY_X_P_ASYM_MD = 2<<7,/* Bit 8..7: asymmetric Pause Mode */
+ PHY_X_P_BOTH_MD = 3<<7,/* Bit 8..7: both Pause Mode */
};
-enum {
- PHY_NP_MORE = 1<<15, /* Bit 15: More, Next Pages to follow */
- PHY_NP_ACK1 = 1<<14, /* Bit 14: (ro) Ack1, for receiving a message */
- PHY_NP_MSG_VAL = 1<<13, /* Bit 13: Message Page valid */
- PHY_NP_ACK2 = 1<<12, /* Bit 12: Ack2, comply with msg content */
- PHY_NP_TOG = 1<<11, /* Bit 11: Toggle Bit, ensure sync */
- PHY_NP_MSG = 0x07ff, /* Bit 10..0: Message from/to Link Partner */
-};
+/***** PHY_XMAC_EXT_STAT 16 bit r/w Extended Status Register *****/
enum {
PHY_X_EX_FD = 1<<15, /* Bit 15: Device Supports Full Duplex */
PHY_X_EX_HD = 1<<14, /* Bit 14: Device Supports Half Duplex */
};
+/***** PHY_XMAC_RES_ABI 16 bit r/o PHY Resolved Ability *****/
enum {
- PHY_X_RS_PAUSE = 3<<7,/* Bit 8..7: selected Pause Mode */
- PHY_X_RS_HD = 1<<6, /* Bit 6: Half Duplex Mode selected */
- PHY_X_RS_FD = 1<<5, /* Bit 5: Full Duplex Mode selected */
- PHY_X_RS_ABLMIS = 1<<4, /* Bit 4: duplex or pause cap mismatch */
- PHY_X_RS_PAUMIS = 1<<3, /* Bit 3: pause capability mismatch */
+ PHY_X_RS_PAUSE = 3<<7, /* Bit 8..7: selected Pause Mode */
+ PHY_X_RS_HD = 1<<6, /* Bit 6: Half Duplex Mode selected */
+ PHY_X_RS_FD = 1<<5, /* Bit 5: Full Duplex Mode selected */
+ PHY_X_RS_ABLMIS = 1<<4, /* Bit 4: duplex or pause cap mismatch */
+ PHY_X_RS_PAUMIS = 1<<3, /* Bit 3: pause capability mismatch */
};
-/** Remote Fault Bits (PHY_X_AN_RFB) encoding */
+/* Remote Fault Bits (PHY_X_AN_RFB) encoding */
enum {
X_RFB_OK = 0<<12,/* Bit 13..12 No errors, Link OK */
- X_RFB_LF = 1<<12, /* Bit 13..12 Link Failure */
+ X_RFB_LF = 1<<12,/* Bit 13..12 Link Failure */
X_RFB_OFF = 2<<12,/* Bit 13..12 Offline */
X_RFB_AN_ERR = 3<<12,/* Bit 13..12 Auto-Negotiation Error */
};
-/* Pause Bits (PHY_X_AN_PAUSE and PHY_X_RS_PAUSE) encoding */
-enum {
- PHY_X_P_NO_PAUSE = 0<<7,/* Bit 8..7: no Pause Mode */
- PHY_X_P_SYM_MD = 1<<7, /* Bit 8..7: symmetric Pause Mode */
- PHY_X_P_ASYM_MD = 2<<7,/* Bit 8..7: asymmetric Pause Mode */
- PHY_X_P_BOTH_MD = 3<<7,/* Bit 8..7: both Pause Mode */
-};
-
-
/* Broadcom-Specific */
/***** PHY_BCOM_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/
enum {
PHY_B_PES_MLT3_ER = 1<<0, /* Bit 0: MLT3 code Error */
};
+/* PHY_BCOM_AUNE_ADV 16 bit r/w Auto-Negotiation Advertisement *****/
+/* PHY_BCOM_AUNE_LP 16 bit r/o Link Partner Ability Reg *****/
+enum {
+ PHY_B_AN_RF = 1<<13, /* Bit 13: Remote Fault */
+
+ PHY_B_AN_ASP = 1<<11, /* Bit 11: Asymmetric Pause */
+ PHY_B_AN_PC = 1<<10, /* Bit 10: Pause Capable */
+};
+
+
/***** PHY_BCOM_FC_CTR 16 bit r/w False Carrier Counter *****/
enum {
PHY_B_FC_CTR = 0xff, /* Bit 7..0: False Carrier Counter */
PHY_B_IS_LST_CHANGE = 1<<1, /* Bit 1: Link Status Changed */
PHY_B_IS_CRC_ER = 1<<0, /* Bit 0: CRC Error */
};
-#define PHY_B_DEF_MSK (~(PHY_B_IS_AN_PR | PHY_B_IS_LST_CHANGE))
+#define PHY_B_DEF_MSK \
+ (~(PHY_B_IS_PSE | PHY_B_IS_AN_PR | PHY_B_IS_DUP_CHANGE | \
+ PHY_B_IS_LSP_CHANGE | PHY_B_IS_LST_CHANGE))
/* Pause Bits (PHY_B_AN_ASP and PHY_B_AN_PC) encoding */
enum {
PHY_B_RES_1000HD = 6<<8,/* Bit 10..8: 1000Base-T Half Dup. */
};
-/*
- * Level One-Specific
- */
-/***** PHY_LONE_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/
-enum {
- PHY_L_1000C_TEST = 7<<13,/* Bit 15..13: Test Modes */
- PHY_L_1000C_MSE = 1<<12, /* Bit 12: Master/Slave Enable */
- PHY_L_1000C_MSC = 1<<11, /* Bit 11: M/S Configuration */
- PHY_L_1000C_RD = 1<<10, /* Bit 10: Repeater/DTE */
- PHY_L_1000C_AFD = 1<<9, /* Bit 9: Advertise Full Duplex */
- PHY_L_1000C_AHD = 1<<8, /* Bit 8: Advertise Half Duplex */
-};
-
-/***** PHY_LONE_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/
-enum {
- PHY_L_1000S_MSF = 1<<15, /* Bit 15: Master/Slave Fault */
- PHY_L_1000S_MSR = 1<<14, /* Bit 14: Master/Slave Result */
- PHY_L_1000S_LRS = 1<<13, /* Bit 13: Local Receiver Status */
- PHY_L_1000S_RRS = 1<<12, /* Bit 12: Remote Receiver Status */
- PHY_L_1000S_LP_FD = 1<<11, /* Bit 11: Link Partner can FD */
- PHY_L_1000S_LP_HD = 1<<10, /* Bit 10: Link Partner can HD */
-
- PHY_L_1000S_IEC = 0xff, /* Bit 7..0: Idle Error Count */
-
-/***** PHY_LONE_EXT_STAT 16 bit r/o Extended Status Register *****/
- PHY_L_ES_X_FD_CAP = 1<<15, /* Bit 15: 1000Base-X FD capable */
- PHY_L_ES_X_HD_CAP = 1<<14, /* Bit 14: 1000Base-X HD capable */
- PHY_L_ES_T_FD_CAP = 1<<13, /* Bit 13: 1000Base-T FD capable */
- PHY_L_ES_T_HD_CAP = 1<<12, /* Bit 12: 1000Base-T HD capable */
-};
-
-/***** PHY_LONE_PORT_CFG 16 bit r/w Port Configuration Reg *****/
-enum {
- PHY_L_PC_REP_MODE = 1<<15, /* Bit 15: Repeater Mode */
-
- PHY_L_PC_TX_DIS = 1<<13, /* Bit 13: Tx output Disabled */
- PHY_L_PC_BY_SCR = 1<<12, /* Bit 12: Bypass Scrambler */
- PHY_L_PC_BY_45 = 1<<11, /* Bit 11: Bypass 4B5B-Decoder */
- PHY_L_PC_JAB_DIS = 1<<10, /* Bit 10: Jabber Disabled */
- PHY_L_PC_SQE = 1<<9, /* Bit 9: Enable Heartbeat */
- PHY_L_PC_TP_LOOP = 1<<8, /* Bit 8: TP Loopback */
- PHY_L_PC_SSS = 1<<7, /* Bit 7: Smart Speed Selection */
- PHY_L_PC_FIFO_SIZE = 1<<6, /* Bit 6: FIFO Size */
- PHY_L_PC_PRE_EN = 1<<5, /* Bit 5: Preamble Enable */
- PHY_L_PC_CIM = 1<<4, /* Bit 4: Carrier Integrity Mon */
- PHY_L_PC_10_SER = 1<<3, /* Bit 3: Use Serial Output */
- PHY_L_PC_ANISOL = 1<<2, /* Bit 2: Unisolate Port */
- PHY_L_PC_TEN_BIT = 1<<1, /* Bit 1: 10bit iface mode on */
- PHY_L_PC_ALTCLOCK = 1<<0, /* Bit 0: (ro) ALTCLOCK Mode on */
-};
-
-/***** PHY_LONE_Q_STAT 16 bit r/o Quick Status Reg *****/
-enum {
- PHY_L_QS_D_RATE = 3<<14,/* Bit 15..14: Data Rate */
- PHY_L_QS_TX_STAT = 1<<13, /* Bit 13: Transmitting */
- PHY_L_QS_RX_STAT = 1<<12, /* Bit 12: Receiving */
- PHY_L_QS_COL_STAT = 1<<11, /* Bit 11: Collision */
- PHY_L_QS_L_STAT = 1<<10, /* Bit 10: Link is up */
- PHY_L_QS_DUP_MOD = 1<<9, /* Bit 9: Full/Half Duplex */
- PHY_L_QS_AN = 1<<8, /* Bit 8: AutoNeg is On */
- PHY_L_QS_AN_C = 1<<7, /* Bit 7: AN is Complete */
- PHY_L_QS_LLE = 7<<4,/* Bit 6..4: Line Length Estim. */
- PHY_L_QS_PAUSE = 1<<3, /* Bit 3: LP advertised Pause */
- PHY_L_QS_AS_PAUSE = 1<<2, /* Bit 2: LP adv. asym. Pause */
- PHY_L_QS_ISOLATE = 1<<1, /* Bit 1: CIM Isolated */
- PHY_L_QS_EVENT = 1<<0, /* Bit 0: Event has occurred */
-};
-
-/***** PHY_LONE_INT_ENAB 16 bit r/w Interrupt Enable Reg *****/
-/***** PHY_LONE_INT_STAT 16 bit r/o Interrupt Status Reg *****/
-enum {
- PHY_L_IS_AN_F = 1<<13, /* Bit 13: Auto-Negotiation fault */
- PHY_L_IS_CROSS = 1<<11, /* Bit 11: Crossover used */
- PHY_L_IS_POL = 1<<10, /* Bit 10: Polarity correct. used */
- PHY_L_IS_SS = 1<<9, /* Bit 9: Smart Speed Downgrade */
- PHY_L_IS_CFULL = 1<<8, /* Bit 8: Counter Full */
- PHY_L_IS_AN_C = 1<<7, /* Bit 7: AutoNeg Complete */
- PHY_L_IS_SPEED = 1<<6, /* Bit 6: Speed Changed */
- PHY_L_IS_DUP = 1<<5, /* Bit 5: Duplex Changed */
- PHY_L_IS_LS = 1<<4, /* Bit 4: Link Status Changed */
- PHY_L_IS_ISOL = 1<<3, /* Bit 3: Isolate Occured */
- PHY_L_IS_MDINT = 1<<2, /* Bit 2: (ro) STAT: MII Int Pending */
- PHY_L_IS_INTEN = 1<<1, /* Bit 1: ENAB: Enable IRQs */
- PHY_L_IS_FORCE = 1<<0, /* Bit 0: ENAB: Force Interrupt */
-};
-
-/* int. mask */
-#define PHY_L_DEF_MSK (PHY_L_IS_LS | PHY_L_IS_ISOL | PHY_L_IS_INTEN)
-
-/***** PHY_LONE_LED_CFG 16 bit r/w LED Configuration Reg *****/
-enum {
- PHY_L_LC_LEDC = 3<<14,/* Bit 15..14: Col/Blink/On/Off */
- PHY_L_LC_LEDR = 3<<12,/* Bit 13..12: Rx/Blink/On/Off */
- PHY_L_LC_LEDT = 3<<10,/* Bit 11..10: Tx/Blink/On/Off */
- PHY_L_LC_LEDG = 3<<8,/* Bit 9..8: Giga/Blink/On/Off */
- PHY_L_LC_LEDS = 3<<6,/* Bit 7..6: 10-100/Blink/On/Off */
- PHY_L_LC_LEDL = 3<<4,/* Bit 5..4: Link/Blink/On/Off */
- PHY_L_LC_LEDF = 3<<2,/* Bit 3..2: Duplex/Blink/On/Off */
- PHY_L_LC_PSTRECH= 1<<1, /* Bit 1: Strech LED Pulses */
- PHY_L_LC_FREQ = 1<<0, /* Bit 0: 30/100 ms */
-};
-
-/***** PHY_LONE_PORT_CTRL 16 bit r/w Port Control Reg *****/
-enum {
- PHY_L_PC_TX_TCLK = 1<<15, /* Bit 15: Enable TX_TCLK */
- PHY_L_PC_ALT_NP = 1<<13, /* Bit 14: Alternate Next Page */
- PHY_L_PC_GMII_ALT= 1<<12, /* Bit 13: Alternate GMII driver */
- PHY_L_PC_TEN_CRS = 1<<10, /* Bit 10: Extend CRS*/
-};
-
-/***** PHY_LONE_CIM 16 bit r/o CIM Reg *****/
-enum {
- PHY_L_CIM_ISOL = 0xff<<8,/* Bit 15..8: Isolate Count */
- PHY_L_CIM_FALSE_CAR = 0xff, /* Bit 7..0: False Carrier Count */
-};
-
-/*
- * Pause Bits (PHY_L_AN_ASP and PHY_L_AN_PC) encoding
- */
-enum {
- PHY_L_P_NO_PAUSE= 0<<10,/* Bit 11..10: no Pause Mode */
- PHY_L_P_SYM_MD = 1<<10, /* Bit 11..10: symmetric Pause Mode */
- PHY_L_P_ASYM_MD = 2<<10,/* Bit 11..10: asymmetric Pause Mode */
- PHY_L_P_BOTH_MD = 3<<10,/* Bit 11..10: both Pause Mode */
-};
-
-/*
- * National-Specific
- */
-/***** PHY_NAT_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/
-enum {
- PHY_N_1000C_TEST= 7<<13,/* Bit 15..13: Test Modes */
- PHY_N_1000C_MSE = 1<<12, /* Bit 12: Master/Slave Enable */
- PHY_N_1000C_MSC = 1<<11, /* Bit 11: M/S Configuration */
- PHY_N_1000C_RD = 1<<10, /* Bit 10: Repeater/DTE */
- PHY_N_1000C_AFD = 1<<9, /* Bit 9: Advertise Full Duplex */
- PHY_N_1000C_AHD = 1<<8, /* Bit 8: Advertise Half Duplex */
- PHY_N_1000C_APC = 1<<7, /* Bit 7: Asymmetric Pause Cap. */};
-
-
-/***** PHY_NAT_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/
-enum {
- PHY_N_1000S_MSF = 1<<15, /* Bit 15: Master/Slave Fault */
- PHY_N_1000S_MSR = 1<<14, /* Bit 14: Master/Slave Result */
- PHY_N_1000S_LRS = 1<<13, /* Bit 13: Local Receiver Status */
- PHY_N_1000S_RRS = 1<<12, /* Bit 12: Remote Receiver Status*/
- PHY_N_1000S_LP_FD= 1<<11, /* Bit 11: Link Partner can FD */
- PHY_N_1000S_LP_HD= 1<<10, /* Bit 10: Link Partner can HD */
- PHY_N_1000C_LP_APC= 1<<9, /* Bit 9: LP Asym. Pause Cap. */
- PHY_N_1000S_IEC = 0xff, /* Bit 7..0: Idle Error Count */
-};
-
-/***** PHY_NAT_EXT_STAT 16 bit r/o Extended Status Register *****/
-enum {
- PHY_N_ES_X_FD_CAP= 1<<15, /* Bit 15: 1000Base-X FD capable */
- PHY_N_ES_X_HD_CAP= 1<<14, /* Bit 14: 1000Base-X HD capable */
- PHY_N_ES_T_FD_CAP= 1<<13, /* Bit 13: 1000Base-T FD capable */
- PHY_N_ES_T_HD_CAP= 1<<12, /* Bit 12: 1000Base-T HD capable */
-};
-
/** Marvell-Specific */
enum {
PHY_M_AN_NXT_PG = 1<<15, /* Request Next Page */
/* special defines for FIBER (88E1011S only) */
enum {
- PHY_M_AN_ASP_X = 1<<8, /* Asymmetric Pause */
- PHY_M_AN_PC_X = 1<<7, /* MAC Pause implemented */
+ PHY_M_AN_ASP_X = 1<<8, /* Asymmetric Pause */
+ PHY_M_AN_PC_X = 1<<7, /* MAC Pause implemented */
PHY_M_AN_1000X_AHD = 1<<6, /* Advertise 10000Base-X Half Duplex */
PHY_M_AN_1000X_AFD = 1<<5, /* Advertise 10000Base-X Full Duplex */
};
/***** PHY_MARV_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/
enum {
- PHY_M_1000C_TEST = 7<<13,/* Bit 15..13: Test Modes */
+ PHY_M_1000C_TEST= 7<<13,/* Bit 15..13: Test Modes */
PHY_M_1000C_MSE = 1<<12, /* Manual Master/Slave Enable */
PHY_M_1000C_MSC = 1<<11, /* M/S Configuration (1=Master) */
PHY_M_1000C_MPD = 1<<10, /* Multi-Port Device */
PHY_M_PC_EN_DET_PLUS = 3<<8, /* Energy Detect Plus (Mode 2) */
};
-#define PHY_M_PC_MDI_XMODE(x) (((x)<<5) & PHY_M_PC_MDIX_MSK)
-
enum {
PHY_M_PC_MAN_MDI = 0, /* 00 = Manual MDI configuration */
PHY_M_PC_MAN_MDIX = 1, /* 01 = Manual MDIX configuration */
PHY_M_IS_DTE_CHANGE = 1<<2, /* DTE Power Det. Status Changed */
PHY_M_IS_POL_CHANGE = 1<<1, /* Polarity Changed */
PHY_M_IS_JABBER = 1<<0, /* Jabber */
-};
-#define PHY_M_DEF_MSK ( PHY_M_IS_AN_ERROR | PHY_M_IS_LSP_CHANGE | \
- PHY_M_IS_LST_CHANGE | PHY_M_IS_FIFO_ERROR)
+ PHY_M_IS_DEF_MSK = PHY_M_IS_AN_ERROR | PHY_M_IS_LSP_CHANGE |
+ PHY_M_IS_LST_CHANGE | PHY_M_IS_FIFO_ERROR,
+
+ PHY_M_IS_AN_MSK = PHY_M_IS_AN_ERROR | PHY_M_IS_AN_COMPL,
+};
/***** PHY_MARV_EXT_CTRL 16 bit r/w Ext. PHY Specific Ctrl *****/
enum {
PHY_M_EC_DIS_LINK_P = 1<<12, /* Disable Link Pulses (88E1111 only) */
PHY_M_EC_M_DSC_MSK = 3<<10, /* Bit 11..10: Master Downshift Counter */
/* (88E1011 only) */
- PHY_M_EC_S_DSC_MSK = 3<<8,/* Bit 9.. 8: Slave Downshift Counter */
+ PHY_M_EC_S_DSC_MSK = 3<<8, /* Bit 9.. 8: Slave Downshift Counter */
/* (88E1011 only) */
- PHY_M_EC_M_DSC_MSK2 = 7<<9,/* Bit 11.. 9: Master Downshift Counter */
+ PHY_M_EC_M_DSC_MSK2 = 7<<9, /* Bit 11.. 9: Master Downshift Counter */
/* (88E1111 only) */
- PHY_M_EC_DOWN_S_ENA = 1<<8, /* Downshift Enable (88E1111 only) */
+ PHY_M_EC_DOWN_S_ENA = 1<<8, /* Downshift Enable (88E1111 only) */
/* !!! Errata in spec. (1 = disable) */
- PHY_M_EC_RX_TIM_CT = 1<<7, /* RGMII Rx Timing Control*/
- PHY_M_EC_MAC_S_MSK = 7<<4,/* Bit 6.. 4: Def. MAC interface speed */
- PHY_M_EC_FIB_AN_ENA = 1<<3, /* Fiber Auto-Neg. Enable (88E1011S only) */
- PHY_M_EC_DTE_D_ENA = 1<<2, /* DTE Detect Enable (88E1111 only) */
- PHY_M_EC_TX_TIM_CT = 1<<1, /* RGMII Tx Timing Control */
- PHY_M_EC_TRANS_DIS = 1<<0, /* Transmitter Disable (88E1111 only) */};
-
-#define PHY_M_EC_M_DSC(x) ((x)<<10) /* 00=1x; 01=2x; 10=3x; 11=4x */
-#define PHY_M_EC_S_DSC(x) ((x)<<8) /* 00=dis; 01=1x; 10=2x; 11=3x */
-#define PHY_M_EC_MAC_S(x) ((x)<<4) /* 01X=0; 110=2.5; 111=25 (MHz) */
-
-#define PHY_M_EC_M_DSC_2(x) ((x)<<9) /* 000=1x; 001=2x; 010=3x; 011=4x */
+ PHY_M_EC_RX_TIM_CT = 1<<7, /* RGMII Rx Timing Control*/
+ PHY_M_EC_MAC_S_MSK = 7<<4, /* Bit 6.. 4: Def. MAC interface speed */
+ PHY_M_EC_FIB_AN_ENA = 1<<3, /* Fiber Auto-Neg. Enable (88E1011S only) */
+ PHY_M_EC_DTE_D_ENA = 1<<2, /* DTE Detect Enable (88E1111 only) */
+ PHY_M_EC_TX_TIM_CT = 1<<1, /* RGMII Tx Timing Control */
+ PHY_M_EC_TRANS_DIS = 1<<0, /* Transmitter Disable (88E1111 only) */};
+
+#define PHY_M_EC_M_DSC(x) ((u16)(x)<<10) /* 00=1x; 01=2x; 10=3x; 11=4x */
+#define PHY_M_EC_S_DSC(x) ((u16)(x)<<8) /* 00=dis; 01=1x; 10=2x; 11=3x */
+#define PHY_M_EC_MAC_S(x) ((u16)(x)<<4) /* 01X=0; 110=2.5; 111=25 (MHz) */
+
+#define PHY_M_EC_M_DSC_2(x) ((u16)(x)<<9) /* 000=1x; 001=2x; 010=3x; 011=4x */
/* 100=5x; 101=6x; 110=7x; 111=8x */
enum {
MAC_TX_CLK_0_MHZ = 2,
PHY_M_LEDC_LK_C_MSK = 7<<3,/* Bit 5.. 3: Link Control Mask */
/* (88E1111 only) */
};
+#define PHY_M_LED_PULS_DUR(x) (((u16)(x)<<12) & PHY_M_LEDC_PULS_MSK)
+#define PHY_M_LED_BLINK_RT(x) (((u16)(x)<<8) & PHY_M_LEDC_BL_R_MSK)
enum {
- PHY_M_LEDC_LINK_MSK = 3<<3,/* Bit 4.. 3: Link Control Mask */
- /* (88E1011 only) */
+ PHY_M_LEDC_LINK_MSK = 3<<3, /* Bit 4.. 3: Link Control Mask */
+ /* (88E1011 only) */
PHY_M_LEDC_DP_CTRL = 1<<2, /* Duplex Control */
PHY_M_LEDC_DP_C_MSB = 1<<2, /* Duplex Control (MSB, 88E1111 only) */
PHY_M_LEDC_RX_CTRL = 1<<1, /* Rx Activity / Link */
PHY_M_LEDC_TX_C_MSB = 1<<0, /* Tx Control (MSB, 88E1111 only) */
};
-#define PHY_M_LED_PULS_DUR(x) ( ((x)<<12) & PHY_M_LEDC_PULS_MSK)
-
enum {
- PULS_NO_STR = 0,/* no pulse stretching */
- PULS_21MS = 1,/* 21 ms to 42 ms */
- PULS_42MS = 2,/* 42 ms to 84 ms */
- PULS_84MS = 3,/* 84 ms to 170 ms */
- PULS_170MS = 4,/* 170 ms to 340 ms */
- PULS_340MS = 5,/* 340 ms to 670 ms */
- PULS_670MS = 6,/* 670 ms to 1.3 s */
- PULS_1300MS = 7,/* 1.3 s to 2.7 s */
+ PULS_NO_STR = 0, /* no pulse stretching */
+ PULS_21MS = 1, /* 21 ms to 42 ms */
+ PULS_42MS = 2, /* 42 ms to 84 ms */
+ PULS_84MS = 3, /* 84 ms to 170 ms */
+ PULS_170MS = 4, /* 170 ms to 340 ms */
+ PULS_340MS = 5, /* 340 ms to 670 ms */
+ PULS_670MS = 6, /* 670 ms to 1.3 s */
+ PULS_1300MS = 7, /* 1.3 s to 2.7 s */
};
-#define PHY_M_LED_BLINK_RT(x) ( ((x)<<8) & PHY_M_LEDC_BL_R_MSK)
enum {
- BLINK_42MS = 0,/* 42 ms */
- BLINK_84MS = 1,/* 84 ms */
- BLINK_170MS = 2,/* 170 ms */
- BLINK_340MS = 3,/* 340 ms */
- BLINK_670MS = 4,/* 670 ms */
+ BLINK_42MS = 0, /* 42 ms */
+ BLINK_84MS = 1, /* 84 ms */
+ BLINK_170MS = 2, /* 170 ms */
+ BLINK_340MS = 3, /* 340 ms */
+ BLINK_670MS = 4, /* 670 ms */
};
/***** PHY_MARV_LED_OVER 16 bit r/w Manual LED Override Reg *****/
PHY_M_EC2_FO_IMPED = 1<<5, /* Fiber Output Impedance */
PHY_M_EC2_FO_M_CLK = 1<<4, /* Fiber Mode Clock Enable */
PHY_M_EC2_FO_BOOST = 1<<3, /* Fiber Output Boost */
- PHY_M_EC2_FO_AM_MSK = 7,/* Bit 2.. 0: Fiber Output Amplitude */
+ PHY_M_EC2_FO_AM_MSK = 7, /* Bit 2.. 0: Fiber Output Amplitude */
};
/***** PHY_MARV_EXT_P_STAT 16 bit r/w Ext. PHY Specific Status *****/
PHY_M_CABD_DIS_WAIT = 1<<15, /* Disable Waiting Period (Page 1) */
/* (88E1111 only) */
PHY_M_CABD_STAT_MSK = 3<<13, /* Bit 14..13: Status Mask */
- PHY_M_CABD_AMPL_MSK = 0x1f<<8,/* Bit 12.. 8: Amplitude Mask */
+ PHY_M_CABD_AMPL_MSK = 0x1f<<8, /* Bit 12.. 8: Amplitude Mask */
/* (88E1111 only) */
PHY_M_CABD_DIST_MSK = 0xff, /* Bit 7.. 0: Distance Mask */
};
PHY_M_FELP_LED0_MSK = 0xf, /* Bit 3.. 0: LED0 Mask (SPEED) */
};
-#define PHY_M_FELP_LED2_CTRL(x) ( ((x)<<8) & PHY_M_FELP_LED2_MSK)
-#define PHY_M_FELP_LED1_CTRL(x) ( ((x)<<4) & PHY_M_FELP_LED1_MSK)
-#define PHY_M_FELP_LED0_CTRL(x) ( ((x)<<0) & PHY_M_FELP_LED0_MSK)
+#define PHY_M_FELP_LED2_CTRL(x) (((x)<<8) & PHY_M_FELP_LED2_MSK)
+#define PHY_M_FELP_LED1_CTRL(x) (((x)<<4) & PHY_M_FELP_LED1_MSK)
+#define PHY_M_FELP_LED0_CTRL(x) (((x)<<0) & PHY_M_FELP_LED0_MSK)
enum {
LED_PAR_CTRL_COLX = 0x00,
PHY_M_FESC_SEL_CL_A = 1<<0, /* Select Class A driver (100B-TX) */
};
-/* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */
-/***** PHY_MARV_PHY_CTRL (page 2) 16 bit r/w MAC Specific Ctrl *****/
-enum {
- PHY_M_MAC_MD_MSK = 7<<7, /* Bit 9.. 7: Mode Select Mask */
- PHY_M_MAC_MD_AUTO = 3,/* Auto Copper/1000Base-X */
- PHY_M_MAC_MD_COPPER = 5,/* Copper only */
- PHY_M_MAC_MD_1000BX = 7,/* 1000Base-X only */
-};
-#define PHY_M_MAC_MODE_SEL(x) ( ((x)<<7) & PHY_M_MAC_MD_MSK)
/***** PHY_MARV_PHY_CTRL (page 3) 16 bit r/w LED Control Reg. *****/
enum {
- PHY_M_LEDC_LOS_MSK = 0xf<<12,/* Bit 15..12: LOS LED Ctrl. Mask */
+ PHY_M_LEDC_LOS_MSK = 0xf<<12, /* Bit 15..12: LOS LED Ctrl. Mask */
PHY_M_LEDC_INIT_MSK = 0xf<<8, /* Bit 11.. 8: INIT LED Ctrl. Mask */
- PHY_M_LEDC_STA1_MSK = 0xf<<4,/* Bit 7.. 4: STAT1 LED Ctrl. Mask */
+ PHY_M_LEDC_STA1_MSK = 0xf<<4, /* Bit 7.. 4: STAT1 LED Ctrl. Mask */
PHY_M_LEDC_STA0_MSK = 0xf, /* Bit 3.. 0: STAT0 LED Ctrl. Mask */
};
-#define PHY_M_LEDC_LOS_CTRL(x) ( ((x)<<12) & PHY_M_LEDC_LOS_MSK)
-#define PHY_M_LEDC_INIT_CTRL(x) ( ((x)<<8) & PHY_M_LEDC_INIT_MSK)
-#define PHY_M_LEDC_STA1_CTRL(x) ( ((x)<<4) & PHY_M_LEDC_STA1_MSK)
-#define PHY_M_LEDC_STA0_CTRL(x) ( ((x)<<0) & PHY_M_LEDC_STA0_MSK)
+#define PHY_M_LEDC_LOS_CTRL(x) (((x)<<12) & PHY_M_LEDC_LOS_MSK)
+#define PHY_M_LEDC_INIT_CTRL(x) (((x)<<8) & PHY_M_LEDC_INIT_MSK)
+#define PHY_M_LEDC_STA1_CTRL(x) (((x)<<4) & PHY_M_LEDC_STA1_MSK)
+#define PHY_M_LEDC_STA0_CTRL(x) (((x)<<0) & PHY_M_LEDC_STA0_MSK)
/* GMAC registers */
/* Port Registers */
GM_GPSR_FC_RX_DIS = 1<<2, /* Bit 2: Rx Flow-Control Mode Disabled */
GM_GPSR_PROM_EN = 1<<1, /* Bit 1: Promiscuous Mode Enabled */
};
-
+
/* GM_GP_CTRL 16 bit r/w General Purpose Control Register */
enum {
GM_GPCR_PROM_ENA = 1<<14, /* Bit 14: Enable Promiscuous Mode */
#define GM_GPCR_SPEED_1000 (GM_GPCR_GIGS_ENA | GM_GPCR_SPEED_100)
#define GM_GPCR_AU_ALL_DIS (GM_GPCR_AU_DUP_DIS | GM_GPCR_AU_FCT_DIS|GM_GPCR_AU_SPD_DIS)
-
+
/* GM_TX_CTRL 16 bit r/w Transmit Control Register */
enum {
GM_TXCR_FORCE_JAM = 1<<15, /* Bit 15: Force Jam / Flow-Control */
GM_TXCR_CRC_DIS = 1<<14, /* Bit 14: Disable insertion of CRC */
GM_TXCR_PAD_DIS = 1<<13, /* Bit 13: Disable padding of packets */
- GM_TXCR_COL_THR_MSK = 1<<10, /* Bit 12..10: Collision Threshold */
+ GM_TXCR_COL_THR_MSK = 7<<10, /* Bit 12..10: Collision Threshold */
};
#define TX_COL_THR(x) (((x)<<10) & GM_TXCR_COL_THR_MSK)
-#define TX_COL_DEF 0x04
-
+#define TX_COL_DEF 0x04 /* late collision after 64 byte */
+
/* GM_RX_CTRL 16 bit r/w Receive Control Register */
enum {
GM_RXCR_UCF_ENA = 1<<15, /* Bit 15: Enable Unicast filtering */
GM_RXCR_CRC_DIS = 1<<13, /* Bit 13: Remove 4-byte CRC */
GM_RXCR_PASS_FC = 1<<12, /* Bit 12: Pass FC packets to FIFO */
};
-
+
/* GM_TX_PARAM 16 bit r/w Transmit Parameter Register */
enum {
GM_TXPA_JAMLEN_MSK = 0x03<<14, /* Bit 15..14: Jam Length */
GM_SMOD_JUMBO_ENA = 1<<8, /* Bit 8: Enable Jumbo (Max. Frame Len) */
GM_SMOD_IPG_MSK = 0x1f /* Bit 4..0: Inter-Packet Gap (IPG) */
};
-
+
#define DATA_BLIND_VAL(x) (((x)<<11) & GM_SMOD_DATABL_MSK)
#define DATA_BLIND_DEF 0x04
/* GM_SMI_CTRL 16 bit r/w SMI Control Register */
enum {
- GM_SMI_CT_PHY_A_MSK = 0x1f<<11,/* Bit 15..11: PHY Device Address */
- GM_SMI_CT_REG_A_MSK = 0x1f<<6,/* Bit 10.. 6: PHY Register Address */
+ GM_SMI_CT_PHY_A_MSK = 0x1f<<11, /* Bit 15..11: PHY Device Address */
+ GM_SMI_CT_REG_A_MSK = 0x1f<<6, /* Bit 10.. 6: PHY Register Address */
GM_SMI_CT_OP_RD = 1<<5, /* Bit 5: OpCode Read (0=Write)*/
GM_SMI_CT_RD_VAL = 1<<4, /* Bit 4: Read Valid (Read completed) */
GM_SMI_CT_BUSY = 1<<3, /* Bit 3: Busy (Operation in progress) */
};
-
+
#define GM_SMI_CT_PHY_AD(x) (((x)<<11) & GM_SMI_CT_PHY_A_MSK)
#define GM_SMI_CT_REG_AD(x) (((x)<<6) & GM_SMI_CT_REG_A_MSK)
GM_PAR_MIB_CLR = 1<<5, /* Bit 5: Set MIB Clear Counter Mode */
GM_PAR_MIB_TST = 1<<4, /* Bit 4: MIB Load Counter (Test Mode) */
};
-
+
/* Receive Frame Status Encoding */
enum {
GMR_FS_LEN = 0xffff<<16, /* Bit 31..16: Rx Frame Length */
+ GMR_FS_LEN_SHIFT = 16,
GMR_FS_VLAN = 1<<13, /* Bit 13: VLAN Packet */
GMR_FS_JABBER = 1<<12, /* Bit 12: Jabber Packet */
GMR_FS_UN_SIZE = 1<<11, /* Bit 11: Undersize Packet */
/*
* GMR_FS_ANY_ERR (analogous to XMR_FS_ANY_ERR)
*/
- GMR_FS_ANY_ERR = GMR_FS_CRC_ERR | GMR_FS_LONG_ERR |
- GMR_FS_MII_ERR | GMR_FS_BAD_FC | GMR_FS_GOOD_FC |
+ GMR_FS_ANY_ERR = GMR_FS_CRC_ERR | GMR_FS_LONG_ERR |
+ GMR_FS_MII_ERR | GMR_FS_BAD_FC | GMR_FS_GOOD_FC |
GMR_FS_JABBER,
/* Rx GMAC FIFO Flush Mask (default) */
RX_FF_FL_DEF_MSK = GMR_FS_CRC_ERR | GMR_FS_RX_FF_OV |GMR_FS_MII_ERR |
- GMR_FS_BAD_FC | GMR_FS_GOOD_FC | GMR_FS_UN_SIZE |
- GMR_FS_JABBER,
+ GMR_FS_BAD_FC | GMR_FS_UN_SIZE | GMR_FS_JABBER,
};
/* RX_GMF_CTRL_T 32 bit Rx GMAC FIFO Control/Test */
/* TX_GMF_CTRL_T 32 bit Tx GMAC FIFO Control/Test */
enum {
- GMF_WSP_TST_ON = 1<<18,/* Write Shadow Pointer Test On */
- GMF_WSP_TST_OFF = 1<<17,/* Write Shadow Pointer Test Off */
- GMF_WSP_STEP = 1<<16,/* Write Shadow Pointer Step/Increment */
+ GMF_WSP_TST_ON = 1<<18, /* Write Shadow Pointer Test On */
+ GMF_WSP_TST_OFF = 1<<17, /* Write Shadow Pointer Test Off */
+ GMF_WSP_STEP = 1<<16, /* Write Shadow Pointer Step/Increment */
GMF_CLI_TX_FU = 1<<6, /* Clear IRQ Tx FIFO Underrun */
GMF_CLI_TX_FC = 1<<5, /* Clear IRQ Tx Frame Complete */
GM_IS_RX_FF_OR = 1<<1, /* Receive FIFO Overrun */
GM_IS_RX_COMPL = 1<<0, /* Frame Reception Complete */
-#define GMAC_DEF_MSK (GM_IS_TX_CO_OV | GM_IS_RX_CO_OV | GM_IS_TX_FF_UR)
+#define GMAC_DEF_MSK (GM_IS_RX_FF_OR | GM_IS_TX_FF_UR)
/* GMAC_LINK_CTRL 16 bit GMAC Link Control Reg (YUKON only) */
/* Bits 15.. 2: reserved */
/* XM_MMU_CMD 16 bit r/w MMU Command Register */
enum {
- XM_MMU_PHY_RDY = 1<<12,/* Bit 12: PHY Read Ready */
- XM_MMU_PHY_BUSY = 1<<11,/* Bit 11: PHY Busy */
- XM_MMU_IGN_PF = 1<<10,/* Bit 10: Ignore Pause Frame */
- XM_MMU_MAC_LB = 1<<9, /* Bit 9: Enable MAC Loopback */
- XM_MMU_FRC_COL = 1<<7, /* Bit 7: Force Collision */
- XM_MMU_SIM_COL = 1<<6, /* Bit 6: Simulate Collision */
- XM_MMU_NO_PRE = 1<<5, /* Bit 5: No MDIO Preamble */
- XM_MMU_GMII_FD = 1<<4, /* Bit 4: GMII uses Full Duplex */
- XM_MMU_RAT_CTRL = 1<<3, /* Bit 3: Enable Rate Control */
- XM_MMU_GMII_LOOP= 1<<2, /* Bit 2: PHY is in Loopback Mode */
- XM_MMU_ENA_RX = 1<<1, /* Bit 1: Enable Receiver */
- XM_MMU_ENA_TX = 1<<0, /* Bit 0: Enable Transmitter */
+ XM_MMU_PHY_RDY = 1<<12, /* Bit 12: PHY Read Ready */
+ XM_MMU_PHY_BUSY = 1<<11, /* Bit 11: PHY Busy */
+ XM_MMU_IGN_PF = 1<<10, /* Bit 10: Ignore Pause Frame */
+ XM_MMU_MAC_LB = 1<<9, /* Bit 9: Enable MAC Loopback */
+ XM_MMU_FRC_COL = 1<<7, /* Bit 7: Force Collision */
+ XM_MMU_SIM_COL = 1<<6, /* Bit 6: Simulate Collision */
+ XM_MMU_NO_PRE = 1<<5, /* Bit 5: No MDIO Preamble */
+ XM_MMU_GMII_FD = 1<<4, /* Bit 4: GMII uses Full Duplex */
+ XM_MMU_RAT_CTRL = 1<<3, /* Bit 3: Enable Rate Control */
+ XM_MMU_GMII_LOOP= 1<<2, /* Bit 2: PHY is in Loopback Mode */
+ XM_MMU_ENA_RX = 1<<1, /* Bit 1: Enable Receiver */
+ XM_MMU_ENA_TX = 1<<0, /* Bit 0: Enable Transmitter */
};
};
-/* XM_PHY_ADDR 16 bit r/w PHY Address Register */
-#define XM_PHY_ADDR_SZ 0x1f /* Bit 4..0: PHY Address bits */
-
-
/* XM_GP_PORT 32 bit r/w General Purpose Port Register */
enum {
XM_GP_ANIP = 1<<6, /* Bit 6: (ro) Auto-Neg. in progress */
XM_IS_LNK_AE = 1<<14, /* Bit 14: Link Asynchronous Event */
XM_IS_TX_ABORT = 1<<13, /* Bit 13: Transmit Abort, late Col. etc */
XM_IS_FRC_INT = 1<<12, /* Bit 12: Force INT bit set in GP */
- XM_IS_INP_ASS = 1<<11, /* Bit 11: Input Asserted, GP bit 0 set */
- XM_IS_LIPA_RC = 1<<10, /* Bit 10: Link Partner requests config */
+ XM_IS_INP_ASS = 1<<11, /* Bit 11: Input Asserted, GP bit 0 set */
+ XM_IS_LIPA_RC = 1<<10, /* Bit 10: Link Partner requests config */
XM_IS_RX_PAGE = 1<<9, /* Bit 9: Page Received */
XM_IS_TX_PAGE = 1<<8, /* Bit 8: Next Page Loaded for Transmit */
XM_IS_AND = 1<<7, /* Bit 7: Auto-Negotiation Done */
XM_IS_TXF_UR = 1<<2, /* Bit 2: Transmit FIFO Underrun */
XM_IS_TX_COMP = 1<<1, /* Bit 1: Frame Tx Complete */
XM_IS_RX_COMP = 1<<0, /* Bit 0: Frame Rx Complete */
-};
-
-#define XM_DEF_MSK (~(XM_IS_INP_ASS | XM_IS_LIPA_RC | XM_IS_RX_PAGE | \
- XM_IS_AND | XM_IS_RXC_OV | XM_IS_TXC_OV | \
- XM_IS_RXF_OV | XM_IS_TXF_UR))
+ XM_IMSK_DISABLE = 0xffff,
+};
/* XM_HW_CFG 16 bit r/w Hardware Config Register */
enum {
};
#define XM_PAUSE_MODE (XM_MD_SPOE_E | XM_MD_SPOL_I | XM_MD_SPOH_I)
-#define XM_DEF_MODE (XM_MD_RX_RUNT | XM_MD_RX_IRLE | XM_MD_RX_LONG |\
- XM_MD_RX_CRCE | XM_MD_RX_ERR | XM_MD_CSA | XM_MD_CAA)
+#define XM_DEF_MODE (XM_MD_RX_RUNT | XM_MD_RX_IRLE | XM_MD_RX_LONG |\
+ XM_MD_RX_CRCE | XM_MD_RX_ERR | XM_MD_CSA)
/* XM_STAT_CMD 16 bit r/w Statistics Command Register */
enum {
struct skge_hw {
void __iomem *regs;
struct pci_dev *pdev;
+ spinlock_t hw_lock;
u32 intr_mask;
struct net_device *dev[2];
- u8 mac_cfg;
u8 chip_id;
+ u8 chip_rev;
+ u8 copper;
+ u8 ports;
u8 phy_type;
- u8 pmd_type;
- u16 phy_addr;
u32 ram_size;
u32 ram_offset;
-
- struct tasklet_struct ext_tasklet;
+ u16 phy_addr;
spinlock_t phy_lock;
+ struct tasklet_struct phy_task;
+
+ char irq_name[0]; /* skge@pci:000:04:00.0 */
};
-static inline int isdualport(const struct skge_hw *hw)
-{
- return !(hw->mac_cfg & CFG_SNG_MAC);
-}
+enum pause_control {
+ FLOW_MODE_NONE = 1, /* No Flow-Control */
+ FLOW_MODE_LOC_SEND = 2, /* Local station sends PAUSE */
+ FLOW_MODE_SYMMETRIC = 3, /* Both stations may send PAUSE */
+ FLOW_MODE_SYM_OR_REM = 4, /* Both stations may send PAUSE or
+ * just the remote station may send PAUSE
+ */
+};
-static inline u8 chip_rev(const struct skge_hw *hw)
-{
- return (hw->mac_cfg & CFG_CHIP_R_MSK) >> 4;
-}
+enum pause_status {
+ FLOW_STAT_INDETERMINATED=0, /* indeterminated */
+ FLOW_STAT_NONE, /* No Flow Control */
+ FLOW_STAT_REM_SEND, /* Remote Station sends PAUSE */
+ FLOW_STAT_LOC_SEND, /* Local station sends PAUSE */
+ FLOW_STAT_SYMMETRIC, /* Both station may send PAUSE */
+};
-static inline int iscopper(const struct skge_hw *hw)
-{
- return (hw->pmd_type == 'T');
-}
-enum {
- FLOW_MODE_NONE = 0, /* No Flow-Control */
- FLOW_MODE_LOC_SEND = 1, /* Local station sends PAUSE */
- FLOW_MODE_REM_SEND = 2, /* Symmetric or just remote */
- FLOW_MODE_SYMMETRIC = 3, /* Both stations may send PAUSE */
-};
-
struct skge_port {
- u32 msg_enable;
struct skge_hw *hw;
struct net_device *netdev;
+ struct napi_struct napi;
int port;
+ u32 msg_enable;
- spinlock_t tx_lock;
- u32 tx_avail;
struct skge_ring tx_ring;
- struct skge_ring rx_ring;
- struct net_device_stats net_stats;
+ struct skge_ring rx_ring ____cacheline_aligned_in_smp;
+ unsigned int rx_buf_size;
+ struct timer_list link_timer;
+ enum pause_control flow_control;
+ enum pause_status flow_status;
u8 rx_csum;
u8 blink_on;
- u8 flow_control;
u8 wol;
u8 autoneg; /* AUTONEG_ENABLE, AUTONEG_DISABLE */
u8 duplex; /* DUPLEX_HALF, DUPLEX_FULL */
void *mem; /* PCI memory for rings */
dma_addr_t dma;
unsigned long mem_size;
-
- struct timer_list link_check;
- struct timer_list led_blink;
+#ifdef CONFIG_SKGE_DEBUG
+ struct dentry *debugfs;
+#endif
};
static inline u32 skge_read32(const struct skge_hw *hw, int reg)
{
return readl(hw->regs + reg);
-
}
static inline u16 skge_read16(const struct skge_hw *hw, int reg)
}
/* MAC Related Registers inside the device. */
-#define SKGEMAC_REG(port,reg) (((port)<<7)+(reg))
-
-/* PCI config space can be accessed via memory mapped space */
-#define SKGEPCI_REG(reg) ((reg)+ 0x380)
-
-#define SKGEXM_REG(port, reg) \
+#define SK_REG(port,reg) (((port)<<7)+(u16)(reg))
+#define SK_XMAC_REG(port, reg) \
((BASE_XMAC_1 + (port) * (BASE_XMAC_2 - BASE_XMAC_1)) | (reg) << 1)
-static inline u32 skge_xm_read32(const struct skge_hw *hw, int port, int reg)
-{
- return skge_read32(hw, SKGEXM_REG(port,reg));
-}
-
-static inline u16 skge_xm_read16(const struct skge_hw *hw, int port, int reg)
-{
- return skge_read16(hw, SKGEXM_REG(port,reg));
-}
-
-static inline u8 skge_xm_read8(const struct skge_hw *hw, int port, int reg)
+static inline u32 xm_read32(const struct skge_hw *hw, int port, int reg)
{
- return skge_read8(hw, SKGEXM_REG(port,reg));
+ u32 v;
+ v = skge_read16(hw, SK_XMAC_REG(port, reg));
+ v |= (u32)skge_read16(hw, SK_XMAC_REG(port, reg+2)) << 16;
+ return v;
}
-static inline void skge_xm_write32(const struct skge_hw *hw, int port, int r, u32 v)
+static inline u16 xm_read16(const struct skge_hw *hw, int port, int reg)
{
- skge_write32(hw, SKGEXM_REG(port,r), v);
+ return skge_read16(hw, SK_XMAC_REG(port,reg));
}
-static inline void skge_xm_write16(const struct skge_hw *hw, int port, int r, u16 v)
+static inline void xm_write32(const struct skge_hw *hw, int port, int r, u32 v)
{
- skge_write16(hw, SKGEXM_REG(port,r), v);
+ skge_write16(hw, SK_XMAC_REG(port,r), v & 0xffff);
+ skge_write16(hw, SK_XMAC_REG(port,r+2), v >> 16);
}
-static inline void skge_xm_write8(const struct skge_hw *hw, int port, int r, u8 v)
+static inline void xm_write16(const struct skge_hw *hw, int port, int r, u16 v)
{
- skge_write8(hw, SKGEXM_REG(port,r), v);
+ skge_write16(hw, SK_XMAC_REG(port,r), v);
}
-static inline void skge_xm_outhash(const struct skge_hw *hw, int port, int reg,
+static inline void xm_outhash(const struct skge_hw *hw, int port, int reg,
const u8 *hash)
{
- skge_xm_write16(hw, port, reg,
- (u16)hash[0] | ((u16)hash[1] << 8));
- skge_xm_write16(hw, port, reg+2,
- (u16)hash[2] | ((u16)hash[3] << 8));
- skge_xm_write16(hw, port, reg+4,
- (u16)hash[4] | ((u16)hash[5] << 8));
- skge_xm_write16(hw, port, reg+6,
- (u16)hash[6] | ((u16)hash[7] << 8));
+ xm_write16(hw, port, reg, (u16)hash[0] | ((u16)hash[1] << 8));
+ xm_write16(hw, port, reg+2, (u16)hash[2] | ((u16)hash[3] << 8));
+ xm_write16(hw, port, reg+4, (u16)hash[4] | ((u16)hash[5] << 8));
+ xm_write16(hw, port, reg+6, (u16)hash[6] | ((u16)hash[7] << 8));
}
-static inline void skge_xm_outaddr(const struct skge_hw *hw, int port, int reg,
+static inline void xm_outaddr(const struct skge_hw *hw, int port, int reg,
const u8 *addr)
{
- skge_xm_write16(hw, port, reg,
- (u16)addr[0] | ((u16)addr[1] << 8));
- skge_xm_write16(hw, port, reg,
- (u16)addr[2] | ((u16)addr[3] << 8));
- skge_xm_write16(hw, port, reg,
- (u16)addr[4] | ((u16)addr[5] << 8));
+ xm_write16(hw, port, reg, (u16)addr[0] | ((u16)addr[1] << 8));
+ xm_write16(hw, port, reg+2, (u16)addr[2] | ((u16)addr[3] << 8));
+ xm_write16(hw, port, reg+4, (u16)addr[4] | ((u16)addr[5] << 8));
}
+#define SK_GMAC_REG(port,reg) \
+ (BASE_GMAC_1 + (port) * (BASE_GMAC_2-BASE_GMAC_1) + (reg))
-#define SKGEGMA_REG(port,reg) \
- ((reg) + BASE_GMAC_1 + \
- (port) * (BASE_GMAC_2-BASE_GMAC_1))
-
-static inline u16 skge_gma_read16(const struct skge_hw *hw, int port, int reg)
-{
- return skge_read16(hw, SKGEGMA_REG(port,reg));
-}
-
-static inline u32 skge_gma_read32(const struct skge_hw *hw, int port, int reg)
+static inline u16 gma_read16(const struct skge_hw *hw, int port, int reg)
{
- return (u32) skge_read16(hw, SKGEGMA_REG(port,reg))
- | ((u32)skge_read16(hw, SKGEGMA_REG(port,reg+4)) << 16);
+ return skge_read16(hw, SK_GMAC_REG(port,reg));
}
-static inline u8 skge_gma_read8(const struct skge_hw *hw, int port, int reg)
+static inline u32 gma_read32(const struct skge_hw *hw, int port, int reg)
{
- return skge_read8(hw, SKGEGMA_REG(port,reg));
+ return (u32) skge_read16(hw, SK_GMAC_REG(port,reg))
+ | ((u32)skge_read16(hw, SK_GMAC_REG(port,reg+4)) << 16);
}
-static inline void skge_gma_write16(const struct skge_hw *hw, int port, int r, u16 v)
+static inline void gma_write16(const struct skge_hw *hw, int port, int r, u16 v)
{
- skge_write16(hw, SKGEGMA_REG(port,r), v);
+ skge_write16(hw, SK_GMAC_REG(port,r), v);
}
-static inline void skge_gma_write32(const struct skge_hw *hw, int port, int r, u32 v)
-{
- skge_write16(hw, SKGEGMA_REG(port, r), (u16) v);
- skge_write32(hw, SKGEGMA_REG(port, r+4), (u16)(v >> 16));
-}
-
-static inline void skge_gma_write8(const struct skge_hw *hw, int port, int r, u8 v)
-{
- skge_write8(hw, SKGEGMA_REG(port,r), v);
-}
-
-static inline void skge_gm_set_addr(struct skge_hw *hw, int port, int reg,
+static inline void gma_set_addr(struct skge_hw *hw, int port, int reg,
const u8 *addr)
{
- skge_gma_write16(hw, port, reg,
- (u16) addr[0] | ((u16) addr[1] << 8));
- skge_gma_write16(hw, port, reg+4,
- (u16) addr[2] | ((u16) addr[3] << 8));
- skge_gma_write16(hw, port, reg+8,
- (u16) addr[4] | ((u16) addr[5] << 8));
+ gma_write16(hw, port, reg, (u16) addr[0] | ((u16) addr[1] << 8));
+ gma_write16(hw, port, reg+4,(u16) addr[2] | ((u16) addr[3] << 8));
+ gma_write16(hw, port, reg+8,(u16) addr[4] | ((u16) addr[5] << 8));
}
-
+
#endif