*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
+ * the Free Software Foundation; either version 2 of the License.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
#include "skge.h"
#define DRV_NAME "skge"
-#define DRV_VERSION "1.6"
+#define DRV_VERSION "1.10"
#define PFX DRV_NAME " "
#define DEFAULT_TX_RING_SIZE 128
#define TX_WATCHDOG (5 * HZ)
#define NAPI_WEIGHT 64
#define BLINK_MS 250
+#define LINK_HZ (HZ/2)
MODULE_DESCRIPTION("SysKonnect Gigabit Ethernet driver");
-MODULE_AUTHOR("Stephen Hemminger <shemminger@osdl.org>");
+MODULE_AUTHOR("Stephen Hemminger <shemminger@linux-foundation.org>");
MODULE_LICENSE("GPL");
MODULE_VERSION(DRV_VERSION);
{ PCI_DEVICE(PCI_VENDOR_ID_3COM, PCI_DEVICE_ID_3COM_3C940B) },
{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, PCI_DEVICE_ID_SYSKONNECT_GE) },
{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, PCI_DEVICE_ID_SYSKONNECT_YU) },
- { PCI_DEVICE(PCI_VENDOR_ID_DLINK, PCI_DEVICE_ID_DLINK_DGE510T), },
+ { PCI_DEVICE(PCI_VENDOR_ID_DLINK, PCI_DEVICE_ID_DLINK_DGE510T) },
{ PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4b01) }, /* DGE-530T */
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4320) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5005) }, /* Belkin */
{ PCI_DEVICE(PCI_VENDOR_ID_CNET, PCI_DEVICE_ID_CNET_GIGACARD) },
{ PCI_DEVICE(PCI_VENDOR_ID_LINKSYS, PCI_DEVICE_ID_LINKSYS_EG1064) },
- { PCI_VENDOR_ID_LINKSYS, 0x1032, PCI_ANY_ID, 0x0015, },
+ { PCI_VENDOR_ID_LINKSYS, 0x1032, PCI_ANY_ID, 0x0015 },
{ 0 }
};
MODULE_DEVICE_TABLE(pci, skge_id_table);
static int skge_up(struct net_device *dev);
static int skge_down(struct net_device *dev);
static void skge_phy_reset(struct skge_port *skge);
-static void skge_tx_clean(struct skge_port *skge);
+static void skge_tx_clean(struct net_device *dev);
static int xm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val);
static int gm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val);
static void genesis_get_stats(struct skge_port *skge, u64 *data);
static const int rxqaddr[] = { Q_R1, Q_R2 };
static const u32 rxirqmask[] = { IS_R1_F, IS_R2_F };
static const u32 txirqmask[] = { IS_XA1_F, IS_XA2_F };
+static const u32 irqmask[] = { IS_R1_F|IS_XA1_F, IS_R2_F|IS_XA2_F };
static int skge_get_regs_len(struct net_device *dev)
{
}
/* Wake on Lan only supported on Yukon chips with rev 1 or above */
-static int wol_supported(const struct skge_hw *hw)
+static u32 wol_supported(const struct skge_hw *hw)
{
- return !((hw->chip_id == CHIP_ID_GENESIS ||
- (hw->chip_id == CHIP_ID_YUKON && hw->chip_rev == 0)));
+ if (hw->chip_id == CHIP_ID_YUKON && hw->chip_rev != 0)
+ return WAKE_MAGIC | WAKE_PHY;
+ else
+ return 0;
+}
+
+static u32 pci_wake_enabled(struct pci_dev *dev)
+{
+ int pm = pci_find_capability(dev, PCI_CAP_ID_PM);
+ u16 value;
+
+ /* If device doesn't support PM Capabilities, but request is to disable
+ * wake events, it's a nop; otherwise fail */
+ if (!pm)
+ return 0;
+
+ pci_read_config_word(dev, pm + PCI_PM_PMC, &value);
+
+ value &= PCI_PM_CAP_PME_MASK;
+ value >>= ffs(PCI_PM_CAP_PME_MASK) - 1; /* First bit of mask */
+
+ return value != 0;
+}
+
+static void skge_wol_init(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ enum pause_control save_mode;
+ u32 ctrl;
+
+ /* Bring hardware out of reset */
+ skge_write16(hw, B0_CTST, CS_RST_CLR);
+ skge_write16(hw, SK_REG(port, GMAC_LINK_CTRL), GMLC_RST_CLR);
+
+ skge_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR);
+ skge_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_CLR);
+
+ /* Force to 10/100 skge_reset will re-enable on resume */
+ save_mode = skge->flow_control;
+ skge->flow_control = FLOW_MODE_SYMMETRIC;
+
+ ctrl = skge->advertising;
+ skge->advertising &= ~(ADVERTISED_1000baseT_Half|ADVERTISED_1000baseT_Full);
+
+ skge_phy_reset(skge);
+
+ skge->flow_control = save_mode;
+ skge->advertising = ctrl;
+
+ /* Set GMAC to no flow control and auto update for speed/duplex */
+ gma_write16(hw, port, GM_GP_CTRL,
+ GM_GPCR_FC_TX_DIS|GM_GPCR_TX_ENA|GM_GPCR_RX_ENA|
+ GM_GPCR_DUP_FULL|GM_GPCR_FC_RX_DIS|GM_GPCR_AU_FCT_DIS);
+
+ /* Set WOL address */
+ memcpy_toio(hw->regs + WOL_REGS(port, WOL_MAC_ADDR),
+ skge->netdev->dev_addr, ETH_ALEN);
+
+ /* Turn on appropriate WOL control bits */
+ skge_write16(hw, WOL_REGS(port, WOL_CTRL_STAT), WOL_CTL_CLEAR_RESULT);
+ ctrl = 0;
+ if (skge->wol & WAKE_PHY)
+ ctrl |= WOL_CTL_ENA_PME_ON_LINK_CHG|WOL_CTL_ENA_LINK_CHG_UNIT;
+ else
+ ctrl |= WOL_CTL_DIS_PME_ON_LINK_CHG|WOL_CTL_DIS_LINK_CHG_UNIT;
+
+ if (skge->wol & WAKE_MAGIC)
+ ctrl |= WOL_CTL_ENA_PME_ON_MAGIC_PKT|WOL_CTL_ENA_MAGIC_PKT_UNIT;
+ else
+ ctrl |= WOL_CTL_DIS_PME_ON_MAGIC_PKT|WOL_CTL_DIS_MAGIC_PKT_UNIT;;
+
+ ctrl |= WOL_CTL_DIS_PME_ON_PATTERN|WOL_CTL_DIS_PATTERN_UNIT;
+ skge_write16(hw, WOL_REGS(port, WOL_CTRL_STAT), ctrl);
+
+ /* block receiver */
+ skge_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET);
}
static void skge_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
{
struct skge_port *skge = netdev_priv(dev);
- wol->supported = wol_supported(skge->hw) ? WAKE_MAGIC : 0;
- wol->wolopts = skge->wol ? WAKE_MAGIC : 0;
+ wol->supported = wol_supported(skge->hw);
+ wol->wolopts = skge->wol;
}
static int skge_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
struct skge_port *skge = netdev_priv(dev);
struct skge_hw *hw = skge->hw;
- if (wol->wolopts != WAKE_MAGIC && wol->wolopts != 0)
- return -EOPNOTSUPP;
-
- if (wol->wolopts == WAKE_MAGIC && !wol_supported(hw))
+ if (wol->wolopts & wol_supported(hw))
return -EOPNOTSUPP;
- skge->wol = wol->wolopts == WAKE_MAGIC;
-
- if (skge->wol) {
- memcpy_toio(hw->regs + WOL_MAC_ADDR, dev->dev_addr, ETH_ALEN);
-
- skge_write16(hw, WOL_CTRL_STAT,
- WOL_CTL_ENA_PME_ON_MAGIC_PKT |
- WOL_CTL_ENA_MAGIC_PKT_UNIT);
- } else
- skge_write16(hw, WOL_CTRL_STAT, WOL_CTL_DEFAULT);
-
+ skge->wol = wol->wolopts;
+ if (!netif_running(dev))
+ skge_wol_init(skge);
return 0;
}
else if (hw->chip_id == CHIP_ID_YUKON)
supported &= ~SUPPORTED_1000baseT_Half;
} else
- supported = SUPPORTED_1000baseT_Full | SUPPORTED_FIBRE
- | SUPPORTED_Autoneg;
+ supported = SUPPORTED_1000baseT_Full | SUPPORTED_1000baseT_Half
+ | SUPPORTED_FIBRE | SUPPORTED_Autoneg;
return supported;
}
{
struct skge_port *skge = netdev_priv(dev);
- ecmd->tx_pause = (skge->flow_control == FLOW_MODE_LOC_SEND)
- || (skge->flow_control == FLOW_MODE_SYMMETRIC);
- ecmd->rx_pause = (skge->flow_control == FLOW_MODE_REM_SEND)
- || (skge->flow_control == FLOW_MODE_SYMMETRIC);
+ ecmd->rx_pause = (skge->flow_control == FLOW_MODE_SYMMETRIC)
+ || (skge->flow_control == FLOW_MODE_SYM_OR_REM);
+ ecmd->tx_pause = ecmd->rx_pause || (skge->flow_control == FLOW_MODE_LOC_SEND);
- ecmd->autoneg = skge->autoneg;
+ ecmd->autoneg = ecmd->rx_pause || ecmd->tx_pause;
}
static int skge_set_pauseparam(struct net_device *dev,
struct ethtool_pauseparam *ecmd)
{
struct skge_port *skge = netdev_priv(dev);
+ struct ethtool_pauseparam old;
- skge->autoneg = ecmd->autoneg;
- if (ecmd->rx_pause && ecmd->tx_pause)
- skge->flow_control = FLOW_MODE_SYMMETRIC;
- else if (ecmd->rx_pause && !ecmd->tx_pause)
- skge->flow_control = FLOW_MODE_REM_SEND;
- else if (!ecmd->rx_pause && ecmd->tx_pause)
- skge->flow_control = FLOW_MODE_LOC_SEND;
- else
- skge->flow_control = FLOW_MODE_NONE;
+ skge_get_pauseparam(dev, &old);
+
+ if (ecmd->autoneg != old.autoneg)
+ skge->flow_control = ecmd->autoneg ? FLOW_MODE_NONE : FLOW_MODE_SYMMETRIC;
+ else {
+ if (ecmd->rx_pause && ecmd->tx_pause)
+ skge->flow_control = FLOW_MODE_SYMMETRIC;
+ else if (ecmd->rx_pause && !ecmd->tx_pause)
+ skge->flow_control = FLOW_MODE_SYM_OR_REM;
+ else if (!ecmd->rx_pause && ecmd->tx_pause)
+ skge->flow_control = FLOW_MODE_LOC_SEND;
+ else
+ skge->flow_control = FLOW_MODE_NONE;
+ }
if (netif_running(dev))
skge_phy_reset(skge);
+
return 0;
}
if (hw->chip_id == CHIP_ID_GENESIS) {
switch (mode) {
case LED_MODE_OFF:
- xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, PHY_B_PEC_LED_OFF);
+ if (hw->phy_type == SK_PHY_BCOM)
+ xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, PHY_B_PEC_LED_OFF);
+ else {
+ skge_write32(hw, SK_REG(port, TX_LED_VAL), 0);
+ skge_write8(hw, SK_REG(port, TX_LED_CTRL), LED_T_OFF);
+ }
skge_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_OFF);
skge_write32(hw, SK_REG(port, RX_LED_VAL), 0);
skge_write8(hw, SK_REG(port, RX_LED_CTRL), LED_T_OFF);
skge_write32(hw, SK_REG(port, RX_LED_VAL), 100);
skge_write8(hw, SK_REG(port, RX_LED_CTRL), LED_START);
- xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, PHY_B_PEC_LED_ON);
- break;
+ if (hw->phy_type == SK_PHY_BCOM)
+ xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, PHY_B_PEC_LED_ON);
+ else {
+ skge_write8(hw, SK_REG(port, TX_LED_TST), LED_T_ON);
+ skge_write32(hw, SK_REG(port, TX_LED_VAL), 100);
+ skge_write8(hw, SK_REG(port, TX_LED_CTRL), LED_START);
+ }
+
}
} else {
switch (mode) {
return 0;
}
-static struct ethtool_ops skge_ethtool_ops = {
+static const struct ethtool_ops skge_ethtool_ops = {
.get_settings = skge_get_settings,
.set_settings = skge_set_settings,
.get_drvinfo = skge_get_drvinfo,
struct skge_element *e;
int i;
- ring->start = kcalloc(sizeof(*e), ring->count, GFP_KERNEL);
+ ring->start = kcalloc(ring->count, sizeof(*e), GFP_KERNEL);
if (!ring->start)
return -ENOMEM;
/* Allocate buffers for receive ring
* For receive: to_clean is next received frame.
*/
-static int skge_rx_fill(struct skge_port *skge)
+static int skge_rx_fill(struct net_device *dev)
{
+ struct skge_port *skge = netdev_priv(dev);
struct skge_ring *ring = &skge->rx_ring;
struct skge_element *e;
do {
struct sk_buff *skb;
- skb = alloc_skb(skge->rx_buf_size + NET_IP_ALIGN, GFP_KERNEL);
+ skb = __netdev_alloc_skb(dev, skge->rx_buf_size + NET_IP_ALIGN,
+ GFP_KERNEL);
if (!skb)
return -ENOMEM;
return 0;
}
+static const char *skge_pause(enum pause_status status)
+{
+ switch(status) {
+ case FLOW_STAT_NONE:
+ return "none";
+ case FLOW_STAT_REM_SEND:
+ return "rx only";
+ case FLOW_STAT_LOC_SEND:
+ return "tx_only";
+ case FLOW_STAT_SYMMETRIC: /* Both station may send PAUSE */
+ return "both";
+ default:
+ return "indeterminated";
+ }
+}
+
+
static void skge_link_up(struct skge_port *skge)
{
skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG),
netif_carrier_on(skge->netdev);
netif_wake_queue(skge->netdev);
- if (netif_msg_link(skge))
+ if (netif_msg_link(skge)) {
printk(KERN_INFO PFX
"%s: Link is up at %d Mbps, %s duplex, flow control %s\n",
skge->netdev->name, skge->speed,
skge->duplex == DUPLEX_FULL ? "full" : "half",
- (skge->flow_control == FLOW_MODE_NONE) ? "none" :
- (skge->flow_control == FLOW_MODE_LOC_SEND) ? "tx only" :
- (skge->flow_control == FLOW_MODE_REM_SEND) ? "rx only" :
- (skge->flow_control == FLOW_MODE_SYMMETRIC) ? "tx and rx" :
- "unknown");
+ skge_pause(skge->flow_status));
+ }
}
static void skge_link_down(struct skge_port *skge)
printk(KERN_INFO PFX "%s: Link is down.\n", skge->netdev->name);
}
+
+static void xm_link_down(struct skge_hw *hw, int port)
+{
+ struct net_device *dev = hw->dev[port];
+ struct skge_port *skge = netdev_priv(dev);
+ u16 cmd, msk;
+
+ if (hw->phy_type == SK_PHY_XMAC) {
+ msk = xm_read16(hw, port, XM_IMSK);
+ msk |= XM_IS_INP_ASS | XM_IS_LIPA_RC | XM_IS_RX_PAGE | XM_IS_AND;
+ xm_write16(hw, port, XM_IMSK, msk);
+ }
+
+ cmd = xm_read16(hw, port, XM_MMU_CMD);
+ cmd &= ~(XM_MMU_ENA_RX | XM_MMU_ENA_TX);
+ xm_write16(hw, port, XM_MMU_CMD, cmd);
+ /* dummy read to ensure writing */
+ (void) xm_read16(hw, port, XM_MMU_CMD);
+
+ if (netif_carrier_ok(dev))
+ skge_link_down(skge);
+}
+
static int __xm_phy_read(struct skge_hw *hw, int port, u16 reg, u16 *val)
{
int i;
xm_write16(hw, port, XM_PHY_ADDR, reg | hw->phy_addr);
*val = xm_read16(hw, port, XM_PHY_DATA);
+ if (hw->phy_type == SK_PHY_XMAC)
+ goto ready;
+
for (i = 0; i < PHY_RETRIES; i++) {
if (xm_read16(hw, port, XM_MMU_CMD) & XM_MMU_PHY_RDY)
goto ready;
xm_write16(hw, port, XM_RX_CMD, 0); /* reset RX CMD Reg */
/* disable Broadcom PHY IRQ */
- xm_write16(hw, port, PHY_BCOM_INT_MASK, 0xffff);
+ if (hw->phy_type == SK_PHY_BCOM)
+ xm_write16(hw, port, PHY_BCOM_INT_MASK, 0xffff);
xm_outhash(hw, port, XM_HSM, zero);
}
[FLOW_MODE_NONE] = 0,
[FLOW_MODE_LOC_SEND] = PHY_AN_PAUSE_ASYM,
[FLOW_MODE_SYMMETRIC] = PHY_AN_PAUSE_CAP,
- [FLOW_MODE_REM_SEND] = PHY_AN_PAUSE_CAP | PHY_AN_PAUSE_ASYM,
+ [FLOW_MODE_SYM_OR_REM] = PHY_AN_PAUSE_CAP | PHY_AN_PAUSE_ASYM,
+};
+
+/* special defines for FIBER (88E1011S only) */
+static const u16 fiber_pause_map[] = {
+ [FLOW_MODE_NONE] = PHY_X_P_NO_PAUSE,
+ [FLOW_MODE_LOC_SEND] = PHY_X_P_ASYM_MD,
+ [FLOW_MODE_SYMMETRIC] = PHY_X_P_SYM_MD,
+ [FLOW_MODE_SYM_OR_REM] = PHY_X_P_BOTH_MD,
};
status = xm_phy_read(hw, port, PHY_BCOM_STAT);
if ((status & PHY_ST_LSYNC) == 0) {
- u16 cmd = xm_read16(hw, port, XM_MMU_CMD);
- cmd &= ~(XM_MMU_ENA_RX | XM_MMU_ENA_TX);
- xm_write16(hw, port, XM_MMU_CMD, cmd);
- /* dummy read to ensure writing */
- (void) xm_read16(hw, port, XM_MMU_CMD);
-
- if (netif_carrier_ok(dev))
- skge_link_down(skge);
- } else {
- if (skge->autoneg == AUTONEG_ENABLE &&
- (status & PHY_ST_AN_OVER)) {
- u16 lpa = xm_phy_read(hw, port, PHY_BCOM_AUNE_LP);
- u16 aux = xm_phy_read(hw, port, PHY_BCOM_AUX_STAT);
-
- if (lpa & PHY_B_AN_RF) {
- printk(KERN_NOTICE PFX "%s: remote fault\n",
- dev->name);
- return;
- }
+ xm_link_down(hw, port);
+ return;
+ }
- /* Check Duplex mismatch */
- switch (aux & PHY_B_AS_AN_RES_MSK) {
- case PHY_B_RES_1000FD:
- skge->duplex = DUPLEX_FULL;
- break;
- case PHY_B_RES_1000HD:
- skge->duplex = DUPLEX_HALF;
- break;
- default:
- printk(KERN_NOTICE PFX "%s: duplex mismatch\n",
- dev->name);
- return;
- }
+ if (skge->autoneg == AUTONEG_ENABLE) {
+ u16 lpa, aux;
+ if (!(status & PHY_ST_AN_OVER))
+ return;
- /* We are using IEEE 802.3z/D5.0 Table 37-4 */
- switch (aux & PHY_B_AS_PAUSE_MSK) {
- case PHY_B_AS_PAUSE_MSK:
- skge->flow_control = FLOW_MODE_SYMMETRIC;
- break;
- case PHY_B_AS_PRR:
- skge->flow_control = FLOW_MODE_REM_SEND;
- break;
- case PHY_B_AS_PRT:
- skge->flow_control = FLOW_MODE_LOC_SEND;
- break;
- default:
- skge->flow_control = FLOW_MODE_NONE;
- }
+ lpa = xm_phy_read(hw, port, PHY_XMAC_AUNE_LP);
+ if (lpa & PHY_B_AN_RF) {
+ printk(KERN_NOTICE PFX "%s: remote fault\n",
+ dev->name);
+ return;
+ }
+
+ aux = xm_phy_read(hw, port, PHY_BCOM_AUX_STAT);
- skge->speed = SPEED_1000;
+ /* Check Duplex mismatch */
+ switch (aux & PHY_B_AS_AN_RES_MSK) {
+ case PHY_B_RES_1000FD:
+ skge->duplex = DUPLEX_FULL;
+ break;
+ case PHY_B_RES_1000HD:
+ skge->duplex = DUPLEX_HALF;
+ break;
+ default:
+ printk(KERN_NOTICE PFX "%s: duplex mismatch\n",
+ dev->name);
+ return;
}
- if (!netif_carrier_ok(dev))
- genesis_link_up(skge);
+ /* We are using IEEE 802.3z/D5.0 Table 37-4 */
+ switch (aux & PHY_B_AS_PAUSE_MSK) {
+ case PHY_B_AS_PAUSE_MSK:
+ skge->flow_status = FLOW_STAT_SYMMETRIC;
+ break;
+ case PHY_B_AS_PRR:
+ skge->flow_status = FLOW_STAT_REM_SEND;
+ break;
+ case PHY_B_AS_PRT:
+ skge->flow_status = FLOW_STAT_LOC_SEND;
+ break;
+ default:
+ skge->flow_status = FLOW_STAT_NONE;
+ }
+ skge->speed = SPEED_1000;
}
+
+ if (!netif_carrier_ok(dev))
+ genesis_link_up(skge);
}
/* Broadcom 5400 only supports giagabit! SysKonnect did not put an additional
* Phy on for 100 or 10Mbit operation
*/
-static void bcom_phy_init(struct skge_port *skge, int jumbo)
+static void bcom_phy_init(struct skge_port *skge)
{
struct skge_hw *hw = skge->hw;
int port = skge->port;
phy_pause_map[skge->flow_control] | PHY_AN_CSMA);
/* Handle Jumbo frames */
- if (jumbo) {
+ if (hw->dev[port]->mtu > ETH_DATA_LEN) {
xm_phy_write(hw, port, PHY_BCOM_AUX_CTRL,
PHY_B_AC_TX_TST | PHY_B_AC_LONG_PACK);
/* Use link status change interrupt */
xm_phy_write(hw, port, PHY_BCOM_INT_MASK, PHY_B_DEF_MSK);
+}
+
+static void xm_phy_init(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ u16 ctrl = 0;
+
+ if (skge->autoneg == AUTONEG_ENABLE) {
+ if (skge->advertising & ADVERTISED_1000baseT_Half)
+ ctrl |= PHY_X_AN_HD;
+ if (skge->advertising & ADVERTISED_1000baseT_Full)
+ ctrl |= PHY_X_AN_FD;
+
+ ctrl |= fiber_pause_map[skge->flow_control];
+
+ xm_phy_write(hw, port, PHY_XMAC_AUNE_ADV, ctrl);
+
+ /* Restart Auto-negotiation */
+ ctrl = PHY_CT_ANE | PHY_CT_RE_CFG;
+ } else {
+ /* Set DuplexMode in Config register */
+ if (skge->duplex == DUPLEX_FULL)
+ ctrl |= PHY_CT_DUP_MD;
+ /*
+ * Do NOT enable Auto-negotiation here. This would hold
+ * the link down because no IDLEs are transmitted
+ */
+ }
+
+ xm_phy_write(hw, port, PHY_XMAC_CTRL, ctrl);
+
+ /* Poll PHY for status changes */
+ schedule_delayed_work(&skge->link_thread, LINK_HZ);
+}
+
+static void xm_check_link(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ u16 status;
+
+ /* read twice because of latch */
+ (void) xm_phy_read(hw, port, PHY_XMAC_STAT);
+ status = xm_phy_read(hw, port, PHY_XMAC_STAT);
+
+ if ((status & PHY_ST_LSYNC) == 0) {
+ xm_link_down(hw, port);
+ return;
+ }
+
+ if (skge->autoneg == AUTONEG_ENABLE) {
+ u16 lpa, res;
+
+ if (!(status & PHY_ST_AN_OVER))
+ return;
+
+ lpa = xm_phy_read(hw, port, PHY_XMAC_AUNE_LP);
+ if (lpa & PHY_B_AN_RF) {
+ printk(KERN_NOTICE PFX "%s: remote fault\n",
+ dev->name);
+ return;
+ }
+
+ res = xm_phy_read(hw, port, PHY_XMAC_RES_ABI);
- bcom_check_link(hw, port);
+ /* Check Duplex mismatch */
+ switch (res & (PHY_X_RS_HD | PHY_X_RS_FD)) {
+ case PHY_X_RS_FD:
+ skge->duplex = DUPLEX_FULL;
+ break;
+ case PHY_X_RS_HD:
+ skge->duplex = DUPLEX_HALF;
+ break;
+ default:
+ printk(KERN_NOTICE PFX "%s: duplex mismatch\n",
+ dev->name);
+ return;
+ }
+
+ /* We are using IEEE 802.3z/D5.0 Table 37-4 */
+ if ((skge->flow_control == FLOW_MODE_SYMMETRIC ||
+ skge->flow_control == FLOW_MODE_SYM_OR_REM) &&
+ (lpa & PHY_X_P_SYM_MD))
+ skge->flow_status = FLOW_STAT_SYMMETRIC;
+ else if (skge->flow_control == FLOW_MODE_SYM_OR_REM &&
+ (lpa & PHY_X_RS_PAUSE) == PHY_X_P_ASYM_MD)
+ /* Enable PAUSE receive, disable PAUSE transmit */
+ skge->flow_status = FLOW_STAT_REM_SEND;
+ else if (skge->flow_control == FLOW_MODE_LOC_SEND &&
+ (lpa & PHY_X_RS_PAUSE) == PHY_X_P_BOTH_MD)
+ /* Disable PAUSE receive, enable PAUSE transmit */
+ skge->flow_status = FLOW_STAT_LOC_SEND;
+ else
+ skge->flow_status = FLOW_STAT_NONE;
+
+ skge->speed = SPEED_1000;
+ }
+
+ if (!netif_carrier_ok(dev))
+ genesis_link_up(skge);
+}
+
+/* Poll to check for link coming up.
+ * Since internal PHY is wired to a level triggered pin, can't
+ * get an interrupt when carrier is detected.
+ */
+static void xm_link_timer(struct work_struct *work)
+{
+ struct skge_port *skge =
+ container_of(work, struct skge_port, link_thread.work);
+ struct net_device *dev = skge->netdev;
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+
+ if (!netif_running(dev))
+ return;
+
+ if (netif_carrier_ok(dev)) {
+ xm_read16(hw, port, XM_ISRC);
+ if (!(xm_read16(hw, port, XM_ISRC) & XM_IS_INP_ASS))
+ goto nochange;
+ } else {
+ if (xm_read32(hw, port, XM_GP_PORT) & XM_GP_INP_ASS)
+ goto nochange;
+ xm_read16(hw, port, XM_ISRC);
+ if (xm_read16(hw, port, XM_ISRC) & XM_IS_INP_ASS)
+ goto nochange;
+ }
+
+ mutex_lock(&hw->phy_mutex);
+ xm_check_link(dev);
+ mutex_unlock(&hw->phy_mutex);
+
+nochange:
+ if (netif_running(dev))
+ schedule_delayed_work(&skge->link_thread, LINK_HZ);
}
static void genesis_mac_init(struct skge_hw *hw, int port)
* namely for the 1000baseTX cards that use the XMAC's
* GMII mode.
*/
- /* Take external Phy out of reset */
- r = skge_read32(hw, B2_GP_IO);
- if (port == 0)
- r |= GP_DIR_0|GP_IO_0;
- else
- r |= GP_DIR_2|GP_IO_2;
+ if (hw->phy_type != SK_PHY_XMAC) {
+ /* Take external Phy out of reset */
+ r = skge_read32(hw, B2_GP_IO);
+ if (port == 0)
+ r |= GP_DIR_0|GP_IO_0;
+ else
+ r |= GP_DIR_2|GP_IO_2;
- skge_write32(hw, B2_GP_IO, r);
+ skge_write32(hw, B2_GP_IO, r);
+ /* Enable GMII interface */
+ xm_write16(hw, port, XM_HW_CFG, XM_HW_GMII_MD);
+ }
- /* Enable GMII interface */
- xm_write16(hw, port, XM_HW_CFG, XM_HW_GMII_MD);
- bcom_phy_init(skge, jumbo);
+ switch(hw->phy_type) {
+ case SK_PHY_XMAC:
+ xm_phy_init(skge);
+ break;
+ case SK_PHY_BCOM:
+ bcom_phy_init(skge);
+ bcom_check_link(hw, port);
+ }
/* Set Station Address */
xm_outaddr(hw, port, XM_SA, dev->dev_addr);
skge_write16(hw, SK_REG(port, TX_MFF_CTRL1), MFF_SET_MAC_RST);
/* For external PHYs there must be special handling */
- reg = skge_read32(hw, B2_GP_IO);
- if (port == 0) {
- reg |= GP_DIR_0;
- reg &= ~GP_IO_0;
- } else {
- reg |= GP_DIR_2;
- reg &= ~GP_IO_2;
+ if (hw->phy_type != SK_PHY_XMAC) {
+ reg = skge_read32(hw, B2_GP_IO);
+ if (port == 0) {
+ reg |= GP_DIR_0;
+ reg &= ~GP_IO_0;
+ } else {
+ reg |= GP_DIR_2;
+ reg &= ~GP_IO_2;
+ }
+ skge_write32(hw, B2_GP_IO, reg);
+ skge_read32(hw, B2_GP_IO);
}
- skge_write32(hw, B2_GP_IO, reg);
- skge_read32(hw, B2_GP_IO);
xm_write16(hw, port, XM_MMU_CMD,
xm_read16(hw, port, XM_MMU_CMD)
printk(KERN_DEBUG PFX "%s: mac interrupt status 0x%x\n",
skge->netdev->name, status);
+ if (hw->phy_type == SK_PHY_XMAC &&
+ (status & (XM_IS_INP_ASS | XM_IS_LIPA_RC)))
+ xm_link_down(hw, port);
+
if (status & XM_IS_TXF_UR) {
xm_write32(hw, port, XM_MODE, XM_MD_FTF);
++skge->net_stats.tx_fifo_errors;
{
struct skge_hw *hw = skge->hw;
int port = skge->port;
- u16 cmd;
- u32 mode, msk;
+ u16 cmd, msk;
+ u32 mode;
cmd = xm_read16(hw, port, XM_MMU_CMD);
* enabling pause frame reception is required for 1000BT
* because the XMAC is not reset if the link is going down
*/
- if (skge->flow_control == FLOW_MODE_NONE ||
- skge->flow_control == FLOW_MODE_LOC_SEND)
+ if (skge->flow_status == FLOW_STAT_NONE ||
+ skge->flow_status == FLOW_STAT_LOC_SEND)
/* Disable Pause Frame Reception */
cmd |= XM_MMU_IGN_PF;
else
xm_write16(hw, port, XM_MMU_CMD, cmd);
mode = xm_read32(hw, port, XM_MODE);
- if (skge->flow_control == FLOW_MODE_SYMMETRIC ||
- skge->flow_control == FLOW_MODE_LOC_SEND) {
+ if (skge->flow_status== FLOW_STAT_SYMMETRIC ||
+ skge->flow_status == FLOW_STAT_LOC_SEND) {
/*
* Configure Pause Frame Generation
* Use internal and external Pause Frame Generation.
}
xm_write32(hw, port, XM_MODE, mode);
-
msk = XM_DEF_MSK;
- /* disable GP0 interrupt bit for external Phy */
- msk |= XM_IS_INP_ASS;
+ if (hw->phy_type != SK_PHY_XMAC)
+ msk |= XM_IS_INP_ASS; /* disable GP0 interrupt bit */
xm_write16(hw, port, XM_IMSK, msk);
xm_read16(hw, port, XM_ISRC);
/* get MMU Command Reg. */
cmd = xm_read16(hw, port, XM_MMU_CMD);
- if (skge->duplex == DUPLEX_FULL)
+ if (hw->phy_type != SK_PHY_XMAC && skge->duplex == DUPLEX_FULL)
cmd |= XM_MMU_GMII_FD;
/*
* Workaround BCOM Errata (#10523) for all BCom Phys
* Enable Power Management after link up
*/
- xm_phy_write(hw, port, PHY_BCOM_AUX_CTRL,
- xm_phy_read(hw, port, PHY_BCOM_AUX_CTRL)
- & ~PHY_B_AC_DIS_PM);
- xm_phy_write(hw, port, PHY_BCOM_INT_MASK, PHY_B_DEF_MSK);
+ if (hw->phy_type == SK_PHY_BCOM) {
+ xm_phy_write(hw, port, PHY_BCOM_AUX_CTRL,
+ xm_phy_read(hw, port, PHY_BCOM_AUX_CTRL)
+ & ~PHY_B_AC_DIS_PM);
+ xm_phy_write(hw, port, PHY_BCOM_INT_MASK, PHY_B_DEF_MSK);
+ }
/* enable Rx/Tx */
xm_write16(hw, port, XM_MMU_CMD,
adv |= PHY_M_AN_10_FD;
if (skge->advertising & ADVERTISED_10baseT_Half)
adv |= PHY_M_AN_10_HD;
- } else /* special defines for FIBER (88E1011S only) */
- adv |= PHY_M_AN_1000X_AHD | PHY_M_AN_1000X_AFD;
- /* Set Flow-control capabilities */
- adv |= phy_pause_map[skge->flow_control];
+ /* Set Flow-control capabilities */
+ adv |= phy_pause_map[skge->flow_control];
+ } else {
+ if (skge->advertising & ADVERTISED_1000baseT_Full)
+ adv |= PHY_M_AN_1000X_AFD;
+ if (skge->advertising & ADVERTISED_1000baseT_Half)
+ adv |= PHY_M_AN_1000X_AHD;
+
+ adv |= fiber_pause_map[skge->flow_control];
+ }
/* Restart Auto-negotiation */
ctrl |= PHY_CT_ANE | PHY_CT_RE_CFG;
case FLOW_MODE_LOC_SEND:
/* disable Rx flow-control */
reg |= GM_GPCR_FC_RX_DIS | GM_GPCR_AU_FCT_DIS;
+ break;
+ case FLOW_MODE_SYMMETRIC:
+ case FLOW_MODE_SYM_OR_REM:
+ /* enable Tx & Rx flow-control */
+ break;
}
gma_write16(hw, port, GM_GP_CTRL, reg);
int port = skge->port;
u16 ctrl;
- gm_phy_write(hw, port, PHY_MARV_INT_MASK, 0);
-
ctrl = gma_read16(hw, port, GM_GP_CTRL);
ctrl &= ~(GM_GPCR_RX_ENA | GM_GPCR_TX_ENA);
gma_write16(hw, port, GM_GP_CTRL, ctrl);
- if (skge->flow_control == FLOW_MODE_REM_SEND) {
+ if (skge->flow_status == FLOW_STAT_REM_SEND) {
+ ctrl = gm_phy_read(hw, port, PHY_MARV_AUNE_ADV);
+ ctrl |= PHY_M_AN_ASP;
/* restore Asymmetric Pause bit */
- gm_phy_write(hw, port, PHY_MARV_AUNE_ADV,
- gm_phy_read(hw, port,
- PHY_MARV_AUNE_ADV)
- | PHY_M_AN_ASP);
-
+ gm_phy_write(hw, port, PHY_MARV_AUNE_ADV, ctrl);
}
- yukon_reset(hw, port);
skge_link_down(skge);
yukon_init(hw, port);
/* We are using IEEE 802.3z/D5.0 Table 37-4 */
switch (phystat & PHY_M_PS_PAUSE_MSK) {
case PHY_M_PS_PAUSE_MSK:
- skge->flow_control = FLOW_MODE_SYMMETRIC;
+ skge->flow_status = FLOW_STAT_SYMMETRIC;
break;
case PHY_M_PS_RX_P_EN:
- skge->flow_control = FLOW_MODE_REM_SEND;
+ skge->flow_status = FLOW_STAT_REM_SEND;
break;
case PHY_M_PS_TX_P_EN:
- skge->flow_control = FLOW_MODE_LOC_SEND;
+ skge->flow_status = FLOW_STAT_LOC_SEND;
break;
default:
- skge->flow_control = FLOW_MODE_NONE;
+ skge->flow_status = FLOW_STAT_NONE;
}
- if (skge->flow_control == FLOW_MODE_NONE ||
+ if (skge->flow_status == FLOW_STAT_NONE ||
(skge->speed < SPEED_1000 && skge->duplex == DUPLEX_HALF))
skge_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
else
{
struct skge_hw *hw = skge->hw;
int port = skge->port;
+ struct net_device *dev = hw->dev[port];
netif_stop_queue(skge->netdev);
netif_carrier_off(skge->netdev);
yukon_init(hw, port);
}
mutex_unlock(&hw->phy_mutex);
+
+ dev->set_multicast_list(dev);
}
/* Basic MII support */
size_t rx_size, tx_size;
int err;
+ if (!is_valid_ether_addr(dev->dev_addr))
+ return -EINVAL;
+
if (netif_msg_ifup(skge))
printk(KERN_INFO PFX "%s: enabling interface\n", dev->name);
BUG_ON(skge->dma & 7);
if ((u64)skge->dma >> 32 != ((u64) skge->dma + skge->mem_size) >> 32) {
- printk(KERN_ERR PFX "pci_alloc_consistent region crosses 4G boundary\n");
+ dev_err(&hw->pdev->dev, "pci_alloc_consistent region crosses 4G boundary\n");
err = -EINVAL;
goto free_pci_mem;
}
if (err)
goto free_pci_mem;
- err = skge_rx_fill(skge);
+ err = skge_rx_fill(dev);
if (err)
goto free_rx_ring;
printk(KERN_INFO PFX "%s: disabling interface\n", dev->name);
netif_stop_queue(dev);
+ if (hw->chip_id == CHIP_ID_GENESIS && hw->phy_type == SK_PHY_XMAC)
+ cancel_delayed_work(&skge->link_thread);
skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG), LED_OFF);
if (hw->chip_id == CHIP_ID_GENESIS)
skge_led(skge, LED_MODE_OFF);
netif_poll_disable(dev);
- skge_tx_clean(skge);
+ skge_tx_clean(dev);
skge_rx_clean(skge);
kfree(skge->rx_ring.start);
int i;
u32 control, len;
u64 map;
- unsigned long flags;
if (skb_padto(skb, ETH_ZLEN))
return NETDEV_TX_OK;
- if (!spin_trylock_irqsave(&skge->tx_lock, flags))
- /* Collision - tell upper layer to requeue */
- return NETDEV_TX_LOCKED;
-
- if (unlikely(skge_avail(&skge->tx_ring) < skb_shinfo(skb)->nr_frags + 1)) {
- if (!netif_queue_stopped(dev)) {
- netif_stop_queue(dev);
-
- printk(KERN_WARNING PFX "%s: ring full when queue awake!\n",
- dev->name);
- }
- spin_unlock_irqrestore(&skge->tx_lock, flags);
+ if (unlikely(skge_avail(&skge->tx_ring) < skb_shinfo(skb)->nr_frags + 1))
return NETDEV_TX_BUSY;
- }
e = skge->tx_ring.to_use;
td = e->desc;
td->dma_lo = map;
td->dma_hi = map >> 32;
- if (skb->ip_summed == CHECKSUM_HW) {
+ if (skb->ip_summed == CHECKSUM_PARTIAL) {
int offset = skb->h.raw - skb->data;
/* This seems backwards, but it is what the sk98lin
td->csum_offs = 0;
td->csum_start = offset;
- td->csum_write = offset + skb->csum;
+ td->csum_write = offset + skb->csum_offset;
} else
control = BMU_CHECK;
netif_stop_queue(dev);
}
- spin_unlock_irqrestore(&skge->tx_lock, flags);
-
dev->trans_start = jiffies;
return NETDEV_TX_OK;
printk(KERN_DEBUG PFX "%s: tx done slot %td\n",
skge->netdev->name, e - skge->tx_ring.start);
- dev_kfree_skb_any(e->skb);
+ dev_kfree_skb(e->skb);
}
e->skb = NULL;
}
/* Free all buffers in transmit ring */
-static void skge_tx_clean(struct skge_port *skge)
+static void skge_tx_clean(struct net_device *dev)
{
+ struct skge_port *skge = netdev_priv(dev);
struct skge_element *e;
- unsigned long flags;
- spin_lock_irqsave(&skge->tx_lock, flags);
+ netif_tx_lock_bh(dev);
for (e = skge->tx_ring.to_clean; e != skge->tx_ring.to_use; e = e->next) {
struct skge_tx_desc *td = e->desc;
skge_tx_free(skge, e, td->control);
}
skge->tx_ring.to_clean = e;
- netif_wake_queue(skge->netdev);
- spin_unlock_irqrestore(&skge->tx_lock, flags);
+ netif_wake_queue(dev);
+ netif_tx_unlock_bh(dev);
}
static void skge_tx_timeout(struct net_device *dev)
printk(KERN_DEBUG PFX "%s: tx timeout\n", dev->name);
skge_write8(skge->hw, Q_ADDR(txqaddr[skge->port], Q_CSR), CSR_STOP);
- skge_tx_clean(skge);
+ skge_tx_clean(dev);
}
static int skge_change_mtu(struct net_device *dev, int new_mtu)
return err;
}
+static const u8 pause_mc_addr[ETH_ALEN] = { 0x1, 0x80, 0xc2, 0x0, 0x0, 0x1 };
+
+static void genesis_add_filter(u8 filter[8], const u8 *addr)
+{
+ u32 crc, bit;
+
+ crc = ether_crc_le(ETH_ALEN, addr);
+ bit = ~crc & 0x3f;
+ filter[bit/8] |= 1 << (bit%8);
+}
+
static void genesis_set_multicast(struct net_device *dev)
{
struct skge_port *skge = netdev_priv(dev);
memset(filter, 0xff, sizeof(filter));
else {
memset(filter, 0, sizeof(filter));
- for (i = 0; list && i < count; i++, list = list->next) {
- u32 crc, bit;
- crc = ether_crc_le(ETH_ALEN, list->dmi_addr);
- bit = ~crc & 0x3f;
- filter[bit/8] |= 1 << (bit%8);
- }
+
+ if (skge->flow_status == FLOW_STAT_REM_SEND
+ || skge->flow_status == FLOW_STAT_SYMMETRIC)
+ genesis_add_filter(filter, pause_mc_addr);
+
+ for (i = 0; list && i < count; i++, list = list->next)
+ genesis_add_filter(filter, list->dmi_addr);
}
xm_write32(hw, port, XM_MODE, mode);
xm_outhash(hw, port, XM_HSM, filter);
}
+static void yukon_add_filter(u8 filter[8], const u8 *addr)
+{
+ u32 bit = ether_crc(ETH_ALEN, addr) & 0x3f;
+ filter[bit/8] |= 1 << (bit%8);
+}
+
static void yukon_set_multicast(struct net_device *dev)
{
struct skge_port *skge = netdev_priv(dev);
struct skge_hw *hw = skge->hw;
int port = skge->port;
struct dev_mc_list *list = dev->mc_list;
+ int rx_pause = (skge->flow_status == FLOW_STAT_REM_SEND
+ || skge->flow_status == FLOW_STAT_SYMMETRIC);
u16 reg;
u8 filter[8];
reg &= ~(GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA);
else if (dev->flags & IFF_ALLMULTI) /* all multicast */
memset(filter, 0xff, sizeof(filter));
- else if (dev->mc_count == 0) /* no multicast */
+ else if (dev->mc_count == 0 && !rx_pause)/* no multicast */
reg &= ~GM_RXCR_MCF_ENA;
else {
int i;
reg |= GM_RXCR_MCF_ENA;
- for (i = 0; list && i < dev->mc_count; i++, list = list->next) {
- u32 bit = ether_crc(ETH_ALEN, list->dmi_addr) & 0x3f;
- filter[bit/8] |= 1 << (bit%8);
- }
+ if (rx_pause)
+ yukon_add_filter(filter, pause_mc_addr);
+
+ for (i = 0; list && i < dev->mc_count; i++, list = list->next)
+ yukon_add_filter(filter, list->dmi_addr);
}
/* Get receive buffer from descriptor.
* Handles copy of small buffers and reallocation failures
*/
-static inline struct sk_buff *skge_rx_get(struct skge_port *skge,
- struct skge_element *e,
- u32 control, u32 status, u16 csum)
+static struct sk_buff *skge_rx_get(struct net_device *dev,
+ struct skge_element *e,
+ u32 control, u32 status, u16 csum)
{
+ struct skge_port *skge = netdev_priv(dev);
struct sk_buff *skb;
u16 len = control & BMU_BBC;
if (unlikely(netif_msg_rx_status(skge)))
printk(KERN_DEBUG PFX "%s: rx slot %td status 0x%x len %d\n",
- skge->netdev->name, e - skge->rx_ring.start,
+ dev->name, e - skge->rx_ring.start,
status, len);
if (len > skge->rx_buf_size)
goto error;
if (len < RX_COPY_THRESHOLD) {
- skb = alloc_skb(len + 2, GFP_ATOMIC);
+ skb = netdev_alloc_skb(dev, len + 2);
if (!skb)
goto resubmit;
skge_rx_reuse(e, skge->rx_buf_size);
} else {
struct sk_buff *nskb;
- nskb = alloc_skb(skge->rx_buf_size + NET_IP_ALIGN, GFP_ATOMIC);
+ nskb = netdev_alloc_skb(dev, skge->rx_buf_size + NET_IP_ALIGN);
if (!nskb)
goto resubmit;
}
skb_put(skb, len);
- skb->dev = skge->netdev;
if (skge->rx_csum) {
skb->csum = csum;
- skb->ip_summed = CHECKSUM_HW;
+ skb->ip_summed = CHECKSUM_COMPLETE;
}
- skb->protocol = eth_type_trans(skb, skge->netdev);
+ skb->protocol = eth_type_trans(skb, dev);
return skb;
error:
if (netif_msg_rx_err(skge))
printk(KERN_DEBUG PFX "%s: rx err, slot %td control 0x%x status 0x%x\n",
- skge->netdev->name, e - skge->rx_ring.start,
+ dev->name, e - skge->rx_ring.start,
control, status);
if (skge->hw->chip_id == CHIP_ID_GENESIS) {
}
/* Free all buffers in Tx ring which are no longer owned by device */
-static void skge_txirq(struct net_device *dev)
+static void skge_tx_done(struct net_device *dev)
{
struct skge_port *skge = netdev_priv(dev);
struct skge_ring *ring = &skge->tx_ring;
struct skge_element *e;
- rmb();
+ skge_write8(skge->hw, Q_ADDR(txqaddr[skge->port], Q_CSR), CSR_IRQ_CL_F);
- spin_lock(&skge->tx_lock);
+ netif_tx_lock(dev);
for (e = ring->to_clean; e != ring->to_use; e = e->next) {
struct skge_tx_desc *td = e->desc;
}
skge->tx_ring.to_clean = e;
- if (netif_queue_stopped(skge->netdev)
- && skge_avail(&skge->tx_ring) > TX_LOW_WATER)
- netif_wake_queue(skge->netdev);
+ if (skge_avail(&skge->tx_ring) > TX_LOW_WATER)
+ netif_wake_queue(dev);
- spin_unlock(&skge->tx_lock);
+ netif_tx_unlock(dev);
}
static int skge_poll(struct net_device *dev, int *budget)
struct skge_hw *hw = skge->hw;
struct skge_ring *ring = &skge->rx_ring;
struct skge_element *e;
+ unsigned long flags;
int to_do = min(dev->quota, *budget);
int work_done = 0;
+ skge_tx_done(dev);
+
+ skge_write8(hw, Q_ADDR(rxqaddr[skge->port], Q_CSR), CSR_IRQ_CL_F);
+
for (e = ring->to_clean; prefetch(e->next), work_done < to_do; e = e->next) {
struct skge_rx_desc *rd = e->desc;
struct sk_buff *skb;
if (control & BMU_OWN)
break;
- skb = skge_rx_get(skge, e, control, rd->status, rd->csum2);
+ skb = skge_rx_get(dev, e, control, rd->status, rd->csum2);
if (likely(skb)) {
dev->last_rx = jiffies;
netif_receive_skb(skb);
if (work_done >= to_do)
return 1; /* not done */
- netif_rx_complete(dev);
-
- spin_lock_irq(&hw->hw_lock);
- hw->intr_mask |= rxirqmask[skge->port];
+ spin_lock_irqsave(&hw->hw_lock, flags);
+ __netif_rx_complete(dev);
+ hw->intr_mask |= irqmask[skge->port];
skge_write32(hw, B0_IMSK, hw->intr_mask);
- mmiowb();
- spin_unlock_irq(&hw->hw_lock);
+ skge_read32(hw, B0_IMSK);
+ spin_unlock_irqrestore(&hw->hw_lock, flags);
return 0;
}
/* Handle device specific framing and timeout interrupts */
static void skge_error_irq(struct skge_hw *hw)
{
+ struct pci_dev *pdev = hw->pdev;
u32 hwstatus = skge_read32(hw, B0_HWE_ISRC);
if (hw->chip_id == CHIP_ID_GENESIS) {
}
if (hwstatus & IS_RAM_RD_PAR) {
- printk(KERN_ERR PFX "Ram read data parity error\n");
+ dev_err(&pdev->dev, "Ram read data parity error\n");
skge_write16(hw, B3_RI_CTRL, RI_CLR_RD_PERR);
}
if (hwstatus & IS_RAM_WR_PAR) {
- printk(KERN_ERR PFX "Ram write data parity error\n");
+ dev_err(&pdev->dev, "Ram write data parity error\n");
skge_write16(hw, B3_RI_CTRL, RI_CLR_WR_PERR);
}
skge_mac_parity(hw, 1);
if (hwstatus & IS_R1_PAR_ERR) {
- printk(KERN_ERR PFX "%s: receive queue parity error\n",
- hw->dev[0]->name);
+ dev_err(&pdev->dev, "%s: receive queue parity error\n",
+ hw->dev[0]->name);
skge_write32(hw, B0_R1_CSR, CSR_IRQ_CL_P);
}
if (hwstatus & IS_R2_PAR_ERR) {
- printk(KERN_ERR PFX "%s: receive queue parity error\n",
- hw->dev[1]->name);
+ dev_err(&pdev->dev, "%s: receive queue parity error\n",
+ hw->dev[1]->name);
skge_write32(hw, B0_R2_CSR, CSR_IRQ_CL_P);
}
if (hwstatus & (IS_IRQ_MST_ERR|IS_IRQ_STAT)) {
u16 pci_status, pci_cmd;
- pci_read_config_word(hw->pdev, PCI_COMMAND, &pci_cmd);
- pci_read_config_word(hw->pdev, PCI_STATUS, &pci_status);
+ pci_read_config_word(pdev, PCI_COMMAND, &pci_cmd);
+ pci_read_config_word(pdev, PCI_STATUS, &pci_status);
- printk(KERN_ERR PFX "%s: PCI error cmd=%#x status=%#x\n",
- pci_name(hw->pdev), pci_cmd, pci_status);
+ dev_err(&pdev->dev, "PCI error cmd=%#x status=%#x\n",
+ pci_cmd, pci_status);
/* Write the error bits back to clear them. */
pci_status &= PCI_STATUS_ERROR_BITS;
skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
- pci_write_config_word(hw->pdev, PCI_COMMAND,
+ pci_write_config_word(pdev, PCI_COMMAND,
pci_cmd | PCI_COMMAND_SERR | PCI_COMMAND_PARITY);
- pci_write_config_word(hw->pdev, PCI_STATUS, pci_status);
+ pci_write_config_word(pdev, PCI_STATUS, pci_status);
skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
/* if error still set then just ignore it */
hwstatus = skge_read32(hw, B0_HWE_ISRC);
if (hwstatus & IS_IRQ_STAT) {
- printk(KERN_INFO PFX "unable to clear error (so ignoring them)\n");
+ dev_warn(&hw->pdev->dev, "unable to clear error (so ignoring them)\n");
hw->intr_mask &= ~IS_HW_ERR;
}
}
* because accessing phy registers requires spin wait which might
* cause excess interrupt latency.
*/
-static void skge_extirq(void *arg)
+static void skge_extirq(struct work_struct *work)
{
- struct skge_hw *hw = arg;
+ struct skge_hw *hw = container_of(work, struct skge_hw, phy_work);
int port;
mutex_lock(&hw->phy_mutex);
if (netif_running(dev)) {
if (hw->chip_id != CHIP_ID_GENESIS)
yukon_phy_intr(skge);
- else
+ else if (hw->phy_type == SK_PHY_BCOM)
bcom_phy_intr(skge);
}
}
spin_lock_irq(&hw->hw_lock);
hw->intr_mask |= IS_EXT_REG;
skge_write32(hw, B0_IMSK, hw->intr_mask);
+ skge_read32(hw, B0_IMSK);
spin_unlock_irq(&hw->hw_lock);
}
-static irqreturn_t skge_intr(int irq, void *dev_id, struct pt_regs *regs)
+static irqreturn_t skge_intr(int irq, void *dev_id)
{
struct skge_hw *hw = dev_id;
u32 status;
+ int handled = 0;
+ spin_lock(&hw->hw_lock);
/* Reading this register masks IRQ */
status = skge_read32(hw, B0_SP_ISRC);
- if (status == 0)
- return IRQ_NONE;
+ if (status == 0 || status == ~0)
+ goto out;
- spin_lock(&hw->hw_lock);
+ handled = 1;
status &= hw->intr_mask;
if (status & IS_EXT_REG) {
hw->intr_mask &= ~IS_EXT_REG;
schedule_work(&hw->phy_work);
}
- if (status & IS_XA1_F) {
- skge_write8(hw, Q_ADDR(Q_XA1, Q_CSR), CSR_IRQ_CL_F);
- skge_txirq(hw->dev[0]);
- }
-
- if (status & IS_R1_F) {
- skge_write8(hw, Q_ADDR(Q_R1, Q_CSR), CSR_IRQ_CL_F);
- hw->intr_mask &= ~IS_R1_F;
+ if (status & (IS_XA1_F|IS_R1_F)) {
+ hw->intr_mask &= ~(IS_XA1_F|IS_R1_F);
netif_rx_schedule(hw->dev[0]);
}
skge_mac_intr(hw, 0);
if (hw->dev[1]) {
- if (status & IS_XA2_F) {
- skge_write8(hw, Q_ADDR(Q_XA2, Q_CSR), CSR_IRQ_CL_F);
- skge_txirq(hw->dev[1]);
- }
-
- if (status & IS_R2_F) {
- skge_write8(hw, Q_ADDR(Q_R2, Q_CSR), CSR_IRQ_CL_F);
- hw->intr_mask &= ~IS_R2_F;
+ if (status & (IS_XA2_F|IS_R2_F)) {
+ hw->intr_mask &= ~(IS_XA2_F|IS_R2_F);
netif_rx_schedule(hw->dev[1]);
}
skge_error_irq(hw);
skge_write32(hw, B0_IMSK, hw->intr_mask);
+ skge_read32(hw, B0_IMSK);
+out:
spin_unlock(&hw->hw_lock);
- return IRQ_HANDLED;
+ return IRQ_RETVAL(handled);
}
#ifdef CONFIG_NET_POLL_CONTROLLER
struct skge_port *skge = netdev_priv(dev);
disable_irq(dev->irq);
- skge_intr(dev->irq, skge->hw, NULL);
+ skge_intr(dev->irq, skge->hw);
enable_irq(dev->irq);
}
#endif
{
u32 reg;
u16 ctst, pci_status;
- u8 t8, mac_cfg, pmd_type, phy_type;
+ u8 t8, mac_cfg, pmd_type;
int i;
ctst = skge_read16(hw, B0_CTST);
ctst & (CS_CLK_RUN_HOT|CS_CLK_RUN_RST|CS_CLK_RUN_ENA));
hw->chip_id = skge_read8(hw, B2_CHIP_ID);
- phy_type = skge_read8(hw, B2_E_1) & 0xf;
+ hw->phy_type = skge_read8(hw, B2_E_1) & 0xf;
pmd_type = skge_read8(hw, B2_PMD_TYP);
hw->copper = (pmd_type == 'T' || pmd_type == '1');
switch (hw->chip_id) {
case CHIP_ID_GENESIS:
- switch (phy_type) {
+ switch (hw->phy_type) {
+ case SK_PHY_XMAC:
+ hw->phy_addr = PHY_ADDR_XMAC;
+ break;
case SK_PHY_BCOM:
hw->phy_addr = PHY_ADDR_BCOM;
break;
default:
- printk(KERN_ERR PFX "%s: unsupported phy type 0x%x\n",
- pci_name(hw->pdev), phy_type);
+ dev_err(&hw->pdev->dev, "unsupported phy type 0x%x\n",
+ hw->phy_type);
return -EOPNOTSUPP;
}
break;
case CHIP_ID_YUKON:
case CHIP_ID_YUKON_LITE:
case CHIP_ID_YUKON_LP:
- if (phy_type < SK_PHY_MARV_COPPER && pmd_type != 'S')
+ if (hw->phy_type < SK_PHY_MARV_COPPER && pmd_type != 'S')
hw->copper = 1;
hw->phy_addr = PHY_ADDR_MARV;
break;
default:
- printk(KERN_ERR PFX "%s: unsupported chip type 0x%x\n",
- pci_name(hw->pdev), hw->chip_id);
+ dev_err(&hw->pdev->dev, "unsupported chip type 0x%x\n",
+ hw->chip_id);
return -EOPNOTSUPP;
}
else
hw->ram_size = t8 * 4096;
- hw->intr_mask = IS_HW_ERR | IS_EXT_REG | IS_PORT_1;
+ hw->intr_mask = IS_HW_ERR | IS_PORT_1;
if (hw->ports > 1)
hw->intr_mask |= IS_PORT_2;
+ if (!(hw->chip_id == CHIP_ID_GENESIS && hw->phy_type == SK_PHY_XMAC))
+ hw->intr_mask |= IS_EXT_REG;
+
if (hw->chip_id == CHIP_ID_GENESIS)
genesis_init(hw);
else {
/* avoid boards with stuck Hardware error bits */
if ((skge_read32(hw, B0_ISRC) & IS_HW_ERR) &&
(skge_read32(hw, B0_HWE_ISRC) & IS_IRQ_SENSOR)) {
- printk(KERN_WARNING PFX "stuck hardware sensor bit\n");
+ dev_warn(&hw->pdev->dev, "stuck hardware sensor bit\n");
hw->intr_mask &= ~IS_HW_ERR;
}
struct net_device *dev = alloc_etherdev(sizeof(*skge));
if (!dev) {
- printk(KERN_ERR "skge etherdev alloc failed");
+ dev_err(&hw->pdev->dev, "etherdev alloc failed\n");
return NULL;
}
dev->poll_controller = skge_netpoll;
#endif
dev->irq = hw->pdev->irq;
- dev->features = NETIF_F_LLTX;
+
if (highmem)
dev->features |= NETIF_F_HIGHDMA;
/* Auto speed and flow control */
skge->autoneg = AUTONEG_ENABLE;
- skge->flow_control = FLOW_MODE_SYMMETRIC;
+ skge->flow_control = FLOW_MODE_SYM_OR_REM;
skge->duplex = -1;
skge->speed = -1;
skge->advertising = skge_supported_modes(hw);
+ skge->wol = pci_wake_enabled(hw->pdev) ? wol_supported(hw) : 0;
hw->dev[port] = dev;
skge->port = port;
- spin_lock_init(&skge->tx_lock);
+ /* Only used for Genesis XMAC */
+ INIT_DELAYED_WORK(&skge->link_thread, xm_link_timer);
if (hw->chip_id != CHIP_ID_GENESIS) {
dev->features |= NETIF_F_IP_CSUM | NETIF_F_SG;
err = pci_enable_device(pdev);
if (err) {
- printk(KERN_ERR PFX "%s cannot enable PCI device\n",
- pci_name(pdev));
+ dev_err(&pdev->dev, "cannot enable PCI device\n");
goto err_out;
}
err = pci_request_regions(pdev, DRV_NAME);
if (err) {
- printk(KERN_ERR PFX "%s cannot obtain PCI resources\n",
- pci_name(pdev));
+ dev_err(&pdev->dev, "cannot obtain PCI resources\n");
goto err_out_disable_pdev;
}
}
if (err) {
- printk(KERN_ERR PFX "%s no usable DMA configuration\n",
- pci_name(pdev));
+ dev_err(&pdev->dev, "no usable DMA configuration\n");
goto err_out_free_regions;
}
err = -ENOMEM;
hw = kzalloc(sizeof(*hw), GFP_KERNEL);
if (!hw) {
- printk(KERN_ERR PFX "%s: cannot allocate hardware struct\n",
- pci_name(pdev));
+ dev_err(&pdev->dev, "cannot allocate hardware struct\n");
goto err_out_free_regions;
}
hw->pdev = pdev;
mutex_init(&hw->phy_mutex);
- INIT_WORK(&hw->phy_work, skge_extirq, hw);
+ INIT_WORK(&hw->phy_work, skge_extirq);
spin_lock_init(&hw->hw_lock);
hw->regs = ioremap_nocache(pci_resource_start(pdev, 0), 0x4000);
if (!hw->regs) {
- printk(KERN_ERR PFX "%s: cannot map device registers\n",
- pci_name(pdev));
+ dev_err(&pdev->dev, "cannot map device registers\n");
goto err_out_free_hw;
}
- err = request_irq(pdev->irq, skge_intr, IRQF_SHARED, DRV_NAME, hw);
- if (err) {
- printk(KERN_ERR PFX "%s: cannot assign irq %d\n",
- pci_name(pdev), pdev->irq);
- goto err_out_iounmap;
- }
- pci_set_drvdata(pdev, hw);
-
err = skge_reset(hw);
if (err)
- goto err_out_free_irq;
+ goto err_out_iounmap;
printk(KERN_INFO PFX DRV_VERSION " addr 0x%llx irq %d chip %s rev %d\n",
(unsigned long long)pci_resource_start(pdev, 0), pdev->irq,
skge_board_name(hw), hw->chip_rev);
- if ((dev = skge_devinit(hw, 0, using_dac)) == NULL)
+ dev = skge_devinit(hw, 0, using_dac);
+ if (!dev)
goto err_out_led_off;
- if (!is_valid_ether_addr(dev->dev_addr)) {
- printk(KERN_ERR PFX "%s: bad (zero?) ethernet address in rom\n",
- pci_name(pdev));
- err = -EIO;
- goto err_out_free_netdev;
- }
-
+ /* Some motherboards are broken and has zero in ROM. */
+ if (!is_valid_ether_addr(dev->dev_addr))
+ dev_warn(&pdev->dev, "bad (zero?) ethernet address in rom\n");
err = register_netdev(dev);
if (err) {
- printk(KERN_ERR PFX "%s: cannot register net device\n",
- pci_name(pdev));
+ dev_err(&pdev->dev, "cannot register net device\n");
goto err_out_free_netdev;
}
+ err = request_irq(pdev->irq, skge_intr, IRQF_SHARED, dev->name, hw);
+ if (err) {
+ dev_err(&pdev->dev, "%s: cannot assign irq %d\n",
+ dev->name, pdev->irq);
+ goto err_out_unregister;
+ }
skge_show_addr(dev);
if (hw->ports > 1 && (dev1 = skge_devinit(hw, 1, using_dac))) {
skge_show_addr(dev1);
else {
/* Failure to register second port need not be fatal */
- printk(KERN_WARNING PFX "register of second port failed\n");
+ dev_warn(&pdev->dev, "register of second port failed\n");
hw->dev[1] = NULL;
free_netdev(dev1);
}
}
+ pci_set_drvdata(pdev, hw);
return 0;
+err_out_unregister:
+ unregister_netdev(dev);
err_out_free_netdev:
free_netdev(dev);
err_out_led_off:
skge_write16(hw, B0_LED, LED_STAT_OFF);
-err_out_free_irq:
- free_irq(pdev->irq, hw);
err_out_iounmap:
iounmap(hw->regs);
err_out_free_hw:
if (!hw)
return;
+ flush_scheduled_work();
+
if ((dev1 = hw->dev[1]))
unregister_netdev(dev1);
dev0 = hw->dev[0];
spin_lock_irq(&hw->hw_lock);
hw->intr_mask = 0;
skge_write32(hw, B0_IMSK, 0);
+ skge_read32(hw, B0_IMSK);
spin_unlock_irq(&hw->hw_lock);
skge_write16(hw, B0_LED, LED_STAT_OFF);
skge_write8(hw, B0_CTST, CS_RST_SET);
- flush_scheduled_work();
-
free_irq(pdev->irq, hw);
pci_release_regions(pdev);
pci_disable_device(pdev);
}
#ifdef CONFIG_PM
+static int vaux_avail(struct pci_dev *pdev)
+{
+ int pm_cap;
+
+ pm_cap = pci_find_capability(pdev, PCI_CAP_ID_PM);
+ if (pm_cap) {
+ u16 ctl;
+ pci_read_config_word(pdev, pm_cap + PCI_PM_PMC, &ctl);
+ if (ctl & PCI_PM_CAP_AUX_POWER)
+ return 1;
+ }
+ return 0;
+}
+
+
static int skge_suspend(struct pci_dev *pdev, pm_message_t state)
{
struct skge_hw *hw = pci_get_drvdata(pdev);
- int i, wol = 0;
+ int i, err, wol = 0;
+
+ err = pci_save_state(pdev);
+ if (err)
+ return err;
- pci_save_state(pdev);
for (i = 0; i < hw->ports; i++) {
struct net_device *dev = hw->dev[i];
+ struct skge_port *skge = netdev_priv(dev);
- if (netif_running(dev)) {
- struct skge_port *skge = netdev_priv(dev);
+ if (netif_running(dev))
+ skge_down(dev);
+ if (skge->wol)
+ skge_wol_init(skge);
- netif_carrier_off(dev);
- if (skge->wol)
- netif_stop_queue(dev);
- else
- skge_down(dev);
- wol |= skge->wol;
- }
- netif_device_detach(dev);
+ wol |= skge->wol;
}
+ if (wol && vaux_avail(pdev))
+ skge_write8(hw, B0_POWER_CTRL,
+ PC_VAUX_ENA | PC_VCC_ENA | PC_VAUX_ON | PC_VCC_OFF);
+
skge_write32(hw, B0_IMSK, 0);
pci_enable_wake(pdev, pci_choose_state(pdev, state), wol);
pci_set_power_state(pdev, pci_choose_state(pdev, state));
struct skge_hw *hw = pci_get_drvdata(pdev);
int i, err;
- pci_set_power_state(pdev, PCI_D0);
- pci_restore_state(pdev);
+ err = pci_set_power_state(pdev, PCI_D0);
+ if (err)
+ goto out;
+
+ err = pci_restore_state(pdev);
+ if (err)
+ goto out;
+
pci_enable_wake(pdev, PCI_D0, 0);
err = skge_reset(hw);
for (i = 0; i < hw->ports; i++) {
struct net_device *dev = hw->dev[i];
- netif_device_attach(dev);
if (netif_running(dev)) {
err = skge_up(dev);
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff