* of the original driver such as link fail-over and link management because
* those should be done at higher levels.
*
- * Copyright (C) 2004, Stephen Hemminger <shemminger@osdl.org>
+ * Copyright (C) 2004, 2005 Stephen Hemminger <shemminger@osdl.org>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
*/
#include <linux/config.h>
+#include <linux/in.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/delay.h>
#include <linux/crc32.h>
#include <linux/dma-mapping.h>
+#include <linux/mii.h>
#include <asm/irq.h>
#include "skge.h"
#define DRV_NAME "skge"
-#define DRV_VERSION "0.6"
+#define DRV_VERSION "1.3"
#define PFX DRV_NAME " "
#define DEFAULT_TX_RING_SIZE 128
#define DEFAULT_RX_RING_SIZE 512
#define MAX_TX_RING_SIZE 1024
#define MAX_RX_RING_SIZE 4096
+#define RX_COPY_THRESHOLD 128
+#define RX_BUF_SIZE 1536
#define PHY_RETRIES 1000
#define ETH_JUMBO_MTU 9000
#define TX_WATCHDOG (5 * HZ)
#define NAPI_WEIGHT 64
-#define BLINK_HZ (HZ/4)
+#define BLINK_MS 250
MODULE_DESCRIPTION("SysKonnect Gigabit Ethernet driver");
MODULE_AUTHOR("Stephen Hemminger <shemminger@osdl.org>");
{ PCI_DEVICE(PCI_VENDOR_ID_3COM, PCI_DEVICE_ID_3COM_3C940B) },
{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, PCI_DEVICE_ID_SYSKONNECT_GE) },
{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, PCI_DEVICE_ID_SYSKONNECT_YU) },
- { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9E00) }, /* SK-9Exx */
{ PCI_DEVICE(PCI_VENDOR_ID_DLINK, PCI_DEVICE_ID_DLINK_DGE510T), },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4320) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5005) }, /* Belkin */
{ PCI_DEVICE(PCI_VENDOR_ID_CNET, PCI_DEVICE_ID_CNET_GIGACARD) },
- { PCI_DEVICE(PCI_VENDOR_ID_LINKSYS, PCI_DEVICE_ID_LINKSYS_EG1032) },
{ PCI_DEVICE(PCI_VENDOR_ID_LINKSYS, PCI_DEVICE_ID_LINKSYS_EG1064) },
+ { PCI_VENDOR_ID_LINKSYS, 0x1032, PCI_ANY_ID, 0x0015, },
{ 0 }
};
MODULE_DEVICE_TABLE(pci, skge_id_table);
static int skge_up(struct net_device *dev);
static int skge_down(struct net_device *dev);
+static void skge_phy_reset(struct skge_port *skge);
static void skge_tx_clean(struct skge_port *skge);
-static void xm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val);
-static void gm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val);
+static int xm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val);
+static int gm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val);
static void genesis_get_stats(struct skge_port *skge, u64 *data);
static void yukon_get_stats(struct skge_port *skge, u64 *data);
static void yukon_init(struct skge_hw *hw, int port);
-static void yukon_reset(struct skge_hw *hw, int port);
static void genesis_mac_init(struct skge_hw *hw, int port);
-static void genesis_reset(struct skge_hw *hw, int port);
static void genesis_link_up(struct skge_port *skge);
/* Avoid conditionals by using array */
static const u32 txirqmask[] = { IS_XA1_F, IS_XA2_F };
static const u32 portirqmask[] = { IS_PORT_1, IS_PORT_2 };
-/* Don't need to look at whole 16K.
- * last interesting register is descriptor poll timer.
- */
-#define SKGE_REGS_LEN (29*128)
-
static int skge_get_regs_len(struct net_device *dev)
{
- return SKGE_REGS_LEN;
+ return 0x4000;
}
/*
- * Returns copy of control register region
- * I/O region is divided into banks and certain regions are unreadable
+ * Returns copy of whole control register region
+ * Note: skip RAM address register because accessing it will
+ * cause bus hangs!
*/
static void skge_get_regs(struct net_device *dev, struct ethtool_regs *regs,
void *p)
{
const struct skge_port *skge = netdev_priv(dev);
- unsigned long offs;
const void __iomem *io = skge->hw->regs;
- static const unsigned long bankmap
- = (1<<0) | (1<<2) | (1<<8) | (1<<9)
- | (1<<12) | (1<<13) | (1<<14) | (1<<15) | (1<<16)
- | (1<<17) | (1<<20) | (1<<21) | (1<<22) | (1<<23)
- | (1<<24) | (1<<25) | (1<<26) | (1<<27) | (1<<28);
regs->version = 1;
- for (offs = 0; offs < regs->len; offs += 128) {
- u32 len = min_t(u32, 128, regs->len - offs);
+ memset(p, 0, regs->len);
+ memcpy_fromio(p, io, B3_RAM_ADDR);
- if (bankmap & (1<<(offs/128)))
- memcpy_fromio(p + offs, io + offs, len);
- else
- memset(p + offs, 0, len);
- }
+ memcpy_fromio(p + B3_RI_WTO_R1, io + B3_RI_WTO_R1,
+ regs->len - B3_RI_WTO_R1);
}
-/* Wake on Lan only supported on Yukon chps with rev 1 or above */
+/* Wake on Lan only supported on Yukon chips with rev 1 or above */
static int wol_supported(const struct skge_hw *hw)
{
return !((hw->chip_id == CHIP_ID_GENESIS ||
return 0;
}
-/* Determine supported/adverised modes based on hardware.
- * Note: ethtoool ADVERTISED_xxx == SUPPORTED_xxx
+/* Determine supported/advertised modes based on hardware.
+ * Note: ethtool ADVERTISED_xxx == SUPPORTED_xxx
*/
static u32 skge_supported_modes(const struct skge_hw *hw)
{
u32 supported;
- if (iscopper(hw)) {
+ if (hw->copper) {
supported = SUPPORTED_10baseT_Half
| SUPPORTED_10baseT_Full
| SUPPORTED_100baseT_Half
ecmd->transceiver = XCVR_INTERNAL;
ecmd->supported = skge_supported_modes(hw);
- if (iscopper(hw)) {
+ if (hw->copper) {
ecmd->port = PORT_TP;
ecmd->phy_address = hw->phy_addr;
} else
} else {
u32 setting;
- switch(ecmd->speed) {
+ switch (ecmd->speed) {
case SPEED_1000:
if (ecmd->duplex == DUPLEX_FULL)
setting = SUPPORTED_1000baseT_Full;
skge->autoneg = ecmd->autoneg;
skge->advertising = ecmd->advertising;
- if (netif_running(dev)) {
- skge_down(dev);
- skge_up(dev);
- }
+ if (netif_running(dev))
+ skge_phy_reset(skge);
+
return (0);
}
struct ethtool_ringparam *p)
{
struct skge_port *skge = netdev_priv(dev);
+ int err;
if (p->rx_pending == 0 || p->rx_pending > MAX_RX_RING_SIZE ||
p->tx_pending == 0 || p->tx_pending > MAX_TX_RING_SIZE)
if (netif_running(dev)) {
skge_down(dev);
- skge_up(dev);
+ err = skge_up(dev);
+ if (err)
+ dev_close(dev);
}
return 0;
static int skge_nway_reset(struct net_device *dev)
{
struct skge_port *skge = netdev_priv(dev);
- struct skge_hw *hw = skge->hw;
- int port = skge->port;
if (skge->autoneg != AUTONEG_ENABLE || !netif_running(dev))
return -EINVAL;
- spin_lock_bh(&hw->phy_lock);
- if (hw->chip_id == CHIP_ID_GENESIS) {
- genesis_reset(hw, port);
- genesis_mac_init(hw, port);
- } else {
- yukon_reset(hw, port);
- yukon_init(hw, port);
- }
- spin_unlock_bh(&hw->phy_lock);
+ skge_phy_reset(skge);
return 0;
}
else
skge->flow_control = FLOW_MODE_NONE;
- if (netif_running(dev)) {
- skge_down(dev);
- skge_up(dev);
- }
+ if (netif_running(dev))
+ skge_phy_reset(skge);
return 0;
}
return 78215; /* or: 78.125 MHz */
}
-/* Chip hz to microseconds */
+/* Chip HZ to microseconds */
static inline u32 skge_clk2usec(const struct skge_hw *hw, u32 ticks)
{
return (ticks * 1000) / hwkhz(hw);
}
-/* Microseconds to chip hz */
+/* Microseconds to chip HZ */
static inline u32 skge_usecs2clk(const struct skge_hw *hw, u32 usec)
{
return hwkhz(hw) * usec / 1000;
return 0;
}
-static void skge_led_on(struct skge_hw *hw, int port)
+enum led_mode { LED_MODE_OFF, LED_MODE_ON, LED_MODE_TST };
+static void skge_led(struct skge_port *skge, enum led_mode mode)
{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+
+ spin_lock_bh(&hw->phy_lock);
if (hw->chip_id == CHIP_ID_GENESIS) {
- skge_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_ON);
- skge_write8(hw, B0_LED, LED_STAT_ON);
+ switch (mode) {
+ case LED_MODE_OFF:
+ xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, PHY_B_PEC_LED_OFF);
+ skge_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_OFF);
+ skge_write32(hw, SK_REG(port, RX_LED_VAL), 0);
+ skge_write8(hw, SK_REG(port, RX_LED_CTRL), LED_T_OFF);
+ break;
- skge_write8(hw, SK_REG(port, RX_LED_TST), LED_T_ON);
- skge_write32(hw, SK_REG(port, RX_LED_VAL), 100);
- skge_write8(hw, SK_REG(port, RX_LED_CTRL), LED_START);
+ case LED_MODE_ON:
+ skge_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_ON);
+ skge_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_LINKSYNC_ON);
- /* For Broadcom Phy only */
- xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, PHY_B_PEC_LED_ON);
- } else {
- gm_phy_write(hw, port, PHY_MARV_LED_CTRL, 0);
- gm_phy_write(hw, port, PHY_MARV_LED_OVER,
- PHY_M_LED_MO_DUP(MO_LED_ON) |
- PHY_M_LED_MO_10(MO_LED_ON) |
- PHY_M_LED_MO_100(MO_LED_ON) |
- PHY_M_LED_MO_1000(MO_LED_ON) |
- PHY_M_LED_MO_RX(MO_LED_ON));
- }
-}
+ skge_write8(hw, SK_REG(port, RX_LED_CTRL), LED_START);
+ skge_write8(hw, SK_REG(port, TX_LED_CTRL), LED_START);
-static void skge_led_off(struct skge_hw *hw, int port)
-{
- if (hw->chip_id == CHIP_ID_GENESIS) {
- skge_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_OFF);
- skge_write8(hw, B0_LED, LED_STAT_OFF);
+ break;
- skge_write32(hw, SK_REG(port, RX_LED_VAL), 0);
- skge_write8(hw, SK_REG(port, RX_LED_CTRL), LED_T_OFF);
+ case LED_MODE_TST:
+ skge_write8(hw, SK_REG(port, RX_LED_TST), LED_T_ON);
+ skge_write32(hw, SK_REG(port, RX_LED_VAL), 100);
+ skge_write8(hw, SK_REG(port, RX_LED_CTRL), LED_START);
- /* Broadcom only */
- xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, PHY_B_PEC_LED_OFF);
+ xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, PHY_B_PEC_LED_ON);
+ break;
+ }
} else {
- gm_phy_write(hw, port, PHY_MARV_LED_CTRL, 0);
- gm_phy_write(hw, port, PHY_MARV_LED_OVER,
- PHY_M_LED_MO_DUP(MO_LED_OFF) |
- PHY_M_LED_MO_10(MO_LED_OFF) |
- PHY_M_LED_MO_100(MO_LED_OFF) |
- PHY_M_LED_MO_1000(MO_LED_OFF) |
- PHY_M_LED_MO_RX(MO_LED_OFF));
+ switch (mode) {
+ case LED_MODE_OFF:
+ gm_phy_write(hw, port, PHY_MARV_LED_CTRL, 0);
+ gm_phy_write(hw, port, PHY_MARV_LED_OVER,
+ PHY_M_LED_MO_DUP(MO_LED_OFF) |
+ PHY_M_LED_MO_10(MO_LED_OFF) |
+ PHY_M_LED_MO_100(MO_LED_OFF) |
+ PHY_M_LED_MO_1000(MO_LED_OFF) |
+ PHY_M_LED_MO_RX(MO_LED_OFF));
+ break;
+ case LED_MODE_ON:
+ gm_phy_write(hw, port, PHY_MARV_LED_CTRL,
+ PHY_M_LED_PULS_DUR(PULS_170MS) |
+ PHY_M_LED_BLINK_RT(BLINK_84MS) |
+ PHY_M_LEDC_TX_CTRL |
+ PHY_M_LEDC_DP_CTRL);
+
+ gm_phy_write(hw, port, PHY_MARV_LED_OVER,
+ PHY_M_LED_MO_RX(MO_LED_OFF) |
+ (skge->speed == SPEED_100 ?
+ PHY_M_LED_MO_100(MO_LED_ON) : 0));
+ break;
+ case LED_MODE_TST:
+ gm_phy_write(hw, port, PHY_MARV_LED_CTRL, 0);
+ gm_phy_write(hw, port, PHY_MARV_LED_OVER,
+ PHY_M_LED_MO_DUP(MO_LED_ON) |
+ PHY_M_LED_MO_10(MO_LED_ON) |
+ PHY_M_LED_MO_100(MO_LED_ON) |
+ PHY_M_LED_MO_1000(MO_LED_ON) |
+ PHY_M_LED_MO_RX(MO_LED_ON));
+ }
}
-}
-
-static void skge_blink_timer(unsigned long data)
-{
- struct skge_port *skge = (struct skge_port *) data;
- struct skge_hw *hw = skge->hw;
- unsigned long flags;
-
- spin_lock_irqsave(&hw->phy_lock, flags);
- if (skge->blink_on)
- skge_led_on(hw, skge->port);
- else
- skge_led_off(hw, skge->port);
- spin_unlock_irqrestore(&hw->phy_lock, flags);
-
- skge->blink_on = !skge->blink_on;
- mod_timer(&skge->led_blink, jiffies + BLINK_HZ);
+ spin_unlock_bh(&hw->phy_lock);
}
/* blink LED's for finding board */
static int skge_phys_id(struct net_device *dev, u32 data)
{
struct skge_port *skge = netdev_priv(dev);
+ unsigned long ms;
+ enum led_mode mode = LED_MODE_TST;
if (!data || data > (u32)(MAX_SCHEDULE_TIMEOUT / HZ))
- data = (u32)(MAX_SCHEDULE_TIMEOUT / HZ);
+ ms = jiffies_to_msecs(MAX_SCHEDULE_TIMEOUT / HZ) * 1000;
+ else
+ ms = data * 1000;
- /* start blinking */
- skge->blink_on = 1;
- mod_timer(&skge->led_blink, jiffies+1);
+ while (ms > 0) {
+ skge_led(skge, mode);
+ mode ^= LED_MODE_TST;
- msleep_interruptible(data * 1000);
- del_timer_sync(&skge->led_blink);
+ if (msleep_interruptible(BLINK_MS))
+ break;
+ ms -= BLINK_MS;
+ }
- skge_led_off(skge->hw, skge->port);
+ /* back to regular LED state */
+ skge_led(skge, netif_running(dev) ? LED_MODE_ON : LED_MODE_OFF);
return 0;
}
.phys_id = skge_phys_id,
.get_stats_count = skge_get_stats_count,
.get_ethtool_stats = skge_get_ethtool_stats,
+ .get_perm_addr = ethtool_op_get_perm_addr,
};
/*
for (i = 0, e = ring->start, d = vaddr; i < ring->count; i++, e++, d++) {
e->desc = d;
+ e->skb = NULL;
if (i == ring->count - 1) {
e->next = ring->start;
d->next_offset = base;
return 0;
}
-/* Setup buffer for receiving */
-static inline int skge_rx_alloc(struct skge_port *skge,
- struct skge_element *e)
+/* Allocate and setup a new buffer for receiving */
+static void skge_rx_setup(struct skge_port *skge, struct skge_element *e,
+ struct sk_buff *skb, unsigned int bufsize)
{
- unsigned long bufsize = skge->netdev->mtu + ETH_HLEN; /* VLAN? */
struct skge_rx_desc *rd = e->desc;
- struct sk_buff *skb;
u64 map;
- skb = dev_alloc_skb(bufsize + NET_IP_ALIGN);
- if (unlikely(!skb)) {
- printk(KERN_DEBUG PFX "%s: out of memory for receive\n",
- skge->netdev->name);
- return -ENOMEM;
- }
-
- skb->dev = skge->netdev;
- skb_reserve(skb, NET_IP_ALIGN);
-
map = pci_map_single(skge->hw->pdev, skb->data, bufsize,
PCI_DMA_FROMDEVICE);
rd->control = BMU_OWN | BMU_STF | BMU_IRQ_EOF | BMU_TCP_CHECK | bufsize;
pci_unmap_addr_set(e, mapaddr, map);
pci_unmap_len_set(e, maplen, bufsize);
- return 0;
}
-/* Free all unused buffers in receive ring, assumes receiver stopped */
+/* Resume receiving using existing skb,
+ * Note: DMA address is not changed by chip.
+ * MTU not changed while receiver active.
+ */
+static void skge_rx_reuse(struct skge_element *e, unsigned int size)
+{
+ struct skge_rx_desc *rd = e->desc;
+
+ rd->csum2 = 0;
+ rd->csum2_start = ETH_HLEN;
+
+ wmb();
+
+ rd->control = BMU_OWN | BMU_STF | BMU_IRQ_EOF | BMU_TCP_CHECK | size;
+}
+
+
+/* Free all buffers in receive ring, assumes receiver stopped */
static void skge_rx_clean(struct skge_port *skge)
{
struct skge_hw *hw = skge->hw;
struct skge_ring *ring = &skge->rx_ring;
struct skge_element *e;
- for (e = ring->to_clean; e != ring->to_use; e = e->next) {
+ e = ring->start;
+ do {
struct skge_rx_desc *rd = e->desc;
rd->control = 0;
-
- pci_unmap_single(hw->pdev,
- pci_unmap_addr(e, mapaddr),
- pci_unmap_len(e, maplen),
- PCI_DMA_FROMDEVICE);
- dev_kfree_skb(e->skb);
- e->skb = NULL;
- }
- ring->to_clean = e;
+ if (e->skb) {
+ pci_unmap_single(hw->pdev,
+ pci_unmap_addr(e, mapaddr),
+ pci_unmap_len(e, maplen),
+ PCI_DMA_FROMDEVICE);
+ dev_kfree_skb(e->skb);
+ e->skb = NULL;
+ }
+ } while ((e = e->next) != ring->start);
}
+
/* Allocate buffers for receive ring
- * For receive: to_use is refill location
- * to_clean is next received frame.
- *
- * if (to_use == to_clean)
- * then ring all frames in ring need buffers
- * if (to_use->next == to_clean)
- * then ring all frames in ring have buffers
+ * For receive: to_clean is next received frame.
*/
static int skge_rx_fill(struct skge_port *skge)
{
struct skge_ring *ring = &skge->rx_ring;
struct skge_element *e;
- int ret = 0;
- for (e = ring->to_use; e->next != ring->to_clean; e = e->next) {
- if (skge_rx_alloc(skge, e)) {
- ret = 1;
- break;
- }
+ e = ring->start;
+ do {
+ struct sk_buff *skb;
- }
- ring->to_use = e;
+ skb = dev_alloc_skb(skge->rx_buf_size + NET_IP_ALIGN);
+ if (!skb)
+ return -ENOMEM;
- return ret;
+ skb_reserve(skb, NET_IP_ALIGN);
+ skge_rx_setup(skge, e, skb, skge->rx_buf_size);
+ } while ( (e = e->next) != ring->start);
+
+ ring->to_clean = ring->start;
+ return 0;
}
static void skge_link_up(struct skge_port *skge)
{
+ skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG),
+ LED_BLK_OFF|LED_SYNC_OFF|LED_ON);
+
netif_carrier_on(skge->netdev);
if (skge->tx_avail > MAX_SKB_FRAGS + 1)
netif_wake_queue(skge->netdev);
static void skge_link_down(struct skge_port *skge)
{
+ skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG), LED_OFF);
netif_carrier_off(skge->netdev);
netif_stop_queue(skge->netdev);
printk(KERN_INFO PFX "%s: Link is down.\n", skge->netdev->name);
}
-static u16 xm_phy_read(struct skge_hw *hw, int port, u16 reg)
+static int __xm_phy_read(struct skge_hw *hw, int port, u16 reg, u16 *val)
{
int i;
- u16 v;
xm_write16(hw, port, XM_PHY_ADDR, reg | hw->phy_addr);
- v = xm_read16(hw, port, XM_PHY_DATA);
+ xm_read16(hw, port, XM_PHY_DATA);
/* Need to wait for external PHY */
for (i = 0; i < PHY_RETRIES; i++) {
udelay(1);
- if (xm_read16(hw, port, XM_MMU_CMD)
- & XM_MMU_PHY_RDY)
+ if (xm_read16(hw, port, XM_MMU_CMD) & XM_MMU_PHY_RDY)
goto ready;
}
- printk(KERN_WARNING PFX "%s: phy read timed out\n",
- hw->dev[port]->name);
- return 0;
+ return -ETIMEDOUT;
ready:
- v = xm_read16(hw, port, XM_PHY_DATA);
+ *val = xm_read16(hw, port, XM_PHY_DATA);
+ return 0;
+}
+
+static u16 xm_phy_read(struct skge_hw *hw, int port, u16 reg)
+{
+ u16 v = 0;
+ if (__xm_phy_read(hw, port, reg, &v))
+ printk(KERN_WARNING PFX "%s: phy read timed out\n",
+ hw->dev[port]->name);
return v;
}
-static void xm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val)
+static int xm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val)
{
int i;
goto ready;
udelay(1);
}
- printk(KERN_WARNING PFX "%s: phy write failed to come ready\n",
- hw->dev[port]->name);
-
+ return -EIO;
ready:
xm_write16(hw, port, XM_PHY_DATA, val);
- for (i = 0; i < PHY_RETRIES; i++) {
- udelay(1);
- if (!(xm_read16(hw, port, XM_MMU_CMD) & XM_MMU_PHY_BUSY))
- return;
- }
- printk(KERN_WARNING PFX "%s: phy write timed out\n",
- hw->dev[port]->name);
+ return 0;
}
static void genesis_init(struct skge_hw *hw)
{
const u8 zero[8] = { 0 };
+ skge_write8(hw, SK_REG(port, GMAC_IRQ_MSK), 0);
+
/* reset the statistics module */
xm_write32(hw, port, XM_GP_PORT, XM_GP_RES_STAT);
xm_write16(hw, port, XM_IMSK, 0xffff); /* disable XMAC IRQs */
(void) xm_phy_read(hw, port, PHY_BCOM_STAT);
status = xm_phy_read(hw, port, PHY_BCOM_STAT);
- pr_debug("bcom_check_link status=0x%x\n", status);
-
if ((status & PHY_ST_LSYNC) == 0) {
u16 cmd = xm_read16(hw, port, XM_MMU_CMD);
cmd &= ~(XM_MMU_ENA_RX | XM_MMU_ENA_TX);
}
/* Check Duplex mismatch */
- switch(aux & PHY_B_AS_AN_RES_MSK) {
+ switch (aux & PHY_B_AS_AN_RES_MSK) {
case PHY_B_RES_1000FD:
skge->duplex = DUPLEX_FULL;
break;
{ 0x17, 0x0013 }, { 0x15, 0x0A04 }, { 0x18, 0x0420 },
};
- pr_debug("bcom_phy_init\n");
-
/* read Id from external PHY (all have the same address) */
id1 = xm_phy_read(hw, port, PHY_XMAC_ID1);
r |= XM_MMU_NO_PRE;
xm_write16(hw, port, XM_MMU_CMD,r);
- switch(id1) {
+ switch (id1) {
case PHY_BCOM_ID1_C0:
/*
* Workaround BCOM Errata for the C0 type.
xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, ext);
xm_phy_write(hw, port, PHY_BCOM_CTRL, ctl);
- /* Use link status change interrrupt */
+ /* Use link status change interrupt */
xm_phy_write(hw, port, PHY_BCOM_INT_MASK, PHY_B_DEF_MSK);
bcom_check_link(hw, port);
xm_write16(hw, port, XM_STAT_CMD,
XM_SC_CLR_RXC | XM_SC_CLR_TXC);
- /* initialize Rx, Tx and Link LED */
- skge_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_ON);
- skge_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_LINKSYNC_ON);
-
- skge_write8(hw, SK_REG(port, RX_LED_CTRL), LED_START);
- skge_write8(hw, SK_REG(port, TX_LED_CTRL), LED_START);
-
/* Unreset the XMAC. */
skge_write16(hw, SK_REG(port, TX_MFF_CTRL1), MFF_CLR_MAC_RST);
* namely for the 1000baseTX cards that use the XMAC's
* GMII mode.
*/
- spin_lock_bh(&hw->phy_lock);
/* Take external Phy out of reset */
r = skge_read32(hw, B2_GP_IO);
if (port == 0)
skge_write32(hw, B2_GP_IO, r);
skge_read32(hw, B2_GP_IO);
- spin_unlock_bh(&hw->phy_lock);
- /* Enable GMII interfac */
+ /* Enable GMII interface */
xm_write16(hw, port, XM_HW_CFG, XM_HW_GMII_MD);
bcom_phy_init(skge, jumbo);
* that jumbo frames larger than 8192 bytes will be
* truncated. Disabling all bad frame filtering causes
* the RX FIFO to operate in streaming mode, in which
- * case the XMAC will start transfering frames out of the
+ * case the XMAC will start transferring frames out of the
* RX FIFO as soon as the FIFO threshold is reached.
*/
xm_write32(hw, port, XM_MODE, XM_DEF_MODE);
int port = skge->port;
u32 reg;
+ genesis_reset(hw, port);
+
/* Clear Tx packet arbiter timeout IRQ */
skge_write16(hw, B3_PA_CTRL,
port == 0 ? PA_CLR_TO_TX1 : PA_CLR_TO_TX2);
/*
- * If the transfer stucks at the MAC the STOP command will not
+ * If the transfer sticks at the MAC the STOP command will not
* terminate if we don't flush the XMAC's transmit FIFO !
*/
xm_write32(hw, port, XM_MODE,
}
}
-static void gm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val)
-{
- int i;
-
- gma_write16(hw, port, GM_SMI_DATA, val);
- gma_write16(hw, port, GM_SMI_CTRL,
- GM_SMI_CT_PHY_AD(hw->phy_addr) | GM_SMI_CT_REG_AD(reg));
- for (i = 0; i < PHY_RETRIES; i++) {
- udelay(1);
-
- if (!(gma_read16(hw, port, GM_SMI_CTRL) & GM_SMI_CT_BUSY))
- break;
- }
-}
-
-static u16 gm_phy_read(struct skge_hw *hw, int port, u16 reg)
-{
- int i;
-
- gma_write16(hw, port, GM_SMI_CTRL,
- GM_SMI_CT_PHY_AD(hw->phy_addr)
- | GM_SMI_CT_REG_AD(reg) | GM_SMI_CT_OP_RD);
-
- for (i = 0; i < PHY_RETRIES; i++) {
- udelay(1);
- if (gma_read16(hw, port, GM_SMI_CTRL) & GM_SMI_CT_RD_VAL)
- goto ready;
- }
-
- printk(KERN_WARNING PFX "%s: phy read timeout\n",
- hw->dev[port]->name);
- return 0;
- ready:
- return gma_read16(hw, port, GM_SMI_DATA);
-}
-
static void genesis_link_up(struct skge_port *skge)
{
struct skge_hw *hw = skge->hw;
u16 cmd;
u32 mode, msk;
- pr_debug("genesis_link_up\n");
cmd = xm_read16(hw, port, XM_MMU_CMD);
/*
}
-/* Marvell Phy Initailization */
+static int gm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val)
+{
+ int i;
+
+ gma_write16(hw, port, GM_SMI_DATA, val);
+ gma_write16(hw, port, GM_SMI_CTRL,
+ GM_SMI_CT_PHY_AD(hw->phy_addr) | GM_SMI_CT_REG_AD(reg));
+ for (i = 0; i < PHY_RETRIES; i++) {
+ udelay(1);
+
+ if (!(gma_read16(hw, port, GM_SMI_CTRL) & GM_SMI_CT_BUSY))
+ return 0;
+ }
+
+ printk(KERN_WARNING PFX "%s: phy write timeout\n",
+ hw->dev[port]->name);
+ return -EIO;
+}
+
+static int __gm_phy_read(struct skge_hw *hw, int port, u16 reg, u16 *val)
+{
+ int i;
+
+ gma_write16(hw, port, GM_SMI_CTRL,
+ GM_SMI_CT_PHY_AD(hw->phy_addr)
+ | GM_SMI_CT_REG_AD(reg) | GM_SMI_CT_OP_RD);
+
+ for (i = 0; i < PHY_RETRIES; i++) {
+ udelay(1);
+ if (gma_read16(hw, port, GM_SMI_CTRL) & GM_SMI_CT_RD_VAL)
+ goto ready;
+ }
+
+ return -ETIMEDOUT;
+ ready:
+ *val = gma_read16(hw, port, GM_SMI_DATA);
+ return 0;
+}
+
+static u16 gm_phy_read(struct skge_hw *hw, int port, u16 reg)
+{
+ u16 v = 0;
+ if (__gm_phy_read(hw, port, reg, &v))
+ printk(KERN_WARNING PFX "%s: phy read timeout\n",
+ hw->dev[port]->name);
+ return v;
+}
+
+/* Marvell Phy Initialization */
static void yukon_init(struct skge_hw *hw, int port)
{
struct skge_port *skge = netdev_priv(hw->dev[port]);
u16 ctrl, ct1000, adv;
- u16 ledctrl, ledover;
- pr_debug("yukon_init\n");
if (skge->autoneg == AUTONEG_ENABLE) {
u16 ectrl = gm_phy_read(hw, port, PHY_MARV_EXT_CTRL);
adv = PHY_AN_CSMA;
if (skge->autoneg == AUTONEG_ENABLE) {
- if (iscopper(hw)) {
+ if (hw->copper) {
if (skge->advertising & ADVERTISED_1000baseT_Full)
ct1000 |= PHY_M_1000C_AFD;
if (skge->advertising & ADVERTISED_1000baseT_Half)
gm_phy_write(hw, port, PHY_MARV_AUNE_ADV, adv);
gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
- /* Setup Phy LED's */
- ledctrl = PHY_M_LED_PULS_DUR(PULS_170MS);
- ledover = 0;
-
- ledctrl |= PHY_M_LED_BLINK_RT(BLINK_84MS) | PHY_M_LEDC_TX_CTRL;
-
- /* turn off the Rx LED (LED_RX) */
- ledover |= PHY_M_LED_MO_RX(MO_LED_OFF);
-
- /* disable blink mode (LED_DUPLEX) on collisions */
- ctrl |= PHY_M_LEDC_DP_CTRL;
- gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
-
- if (skge->autoneg == AUTONEG_DISABLE || skge->speed == SPEED_100) {
- /* turn on 100 Mbps LED (LED_LINK100) */
- ledover |= PHY_M_LED_MO_100(MO_LED_ON);
- }
-
- if (ledover)
- gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover);
-
/* Enable phy interrupt on autonegotiation complete (or link up) */
if (skge->autoneg == AUTONEG_ENABLE)
- gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_AN_COMPL);
+ gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_AN_MSK);
else
- gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK);
+ gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_DEF_MSK);
}
static void yukon_reset(struct skge_hw *hw, int port)
| GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA);
}
+/* Apparently, early versions of Yukon-Lite had wrong chip_id? */
+static int is_yukon_lite_a0(struct skge_hw *hw)
+{
+ u32 reg;
+ int ret;
+
+ if (hw->chip_id != CHIP_ID_YUKON)
+ return 0;
+
+ reg = skge_read32(hw, B2_FAR);
+ skge_write8(hw, B2_FAR + 3, 0xff);
+ ret = (skge_read8(hw, B2_FAR + 3) != 0);
+ skge_write32(hw, B2_FAR, reg);
+ return ret;
+}
+
static void yukon_mac_init(struct skge_hw *hw, int port)
{
struct skge_port *skge = netdev_priv(hw->dev[port]);
/* WA code for COMA mode -- set PHY reset */
if (hw->chip_id == CHIP_ID_YUKON_LITE &&
- hw->chip_rev == CHIP_REV_YU_LITE_A3)
- skge_write32(hw, B2_GP_IO,
- (skge_read32(hw, B2_GP_IO) | GP_DIR_9 | GP_IO_9));
+ hw->chip_rev >= CHIP_REV_YU_LITE_A3) {
+ reg = skge_read32(hw, B2_GP_IO);
+ reg |= GP_DIR_9 | GP_IO_9;
+ skge_write32(hw, B2_GP_IO, reg);
+ }
/* hard reset */
skge_write32(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET);
/* WA code for COMA mode -- clear PHY reset */
if (hw->chip_id == CHIP_ID_YUKON_LITE &&
- hw->chip_rev == CHIP_REV_YU_LITE_A3)
- skge_write32(hw, B2_GP_IO,
- (skge_read32(hw, B2_GP_IO) | GP_DIR_9)
- & ~GP_IO_9);
+ hw->chip_rev >= CHIP_REV_YU_LITE_A3) {
+ reg = skge_read32(hw, B2_GP_IO);
+ reg |= GP_DIR_9;
+ reg &= ~GP_IO_9;
+ skge_write32(hw, B2_GP_IO, reg);
+ }
/* Set hardware config mode */
reg = GPC_INT_POL_HI | GPC_DIS_FC | GPC_DIS_SLEEP |
GPC_ENA_XC | GPC_ANEG_ADV_ALL_M | GPC_ENA_PAUSE;
- reg |= iscopper(hw) ? GPC_HWCFG_GMII_COP : GPC_HWCFG_GMII_FIB;
+ reg |= hw->copper ? GPC_HWCFG_GMII_COP : GPC_HWCFG_GMII_FIB;
/* Clear GMC reset */
skge_write32(hw, SK_REG(port, GPHY_CTRL), reg | GPC_RST_SET);
}
gma_write16(hw, port, GM_GP_CTRL, reg);
- skge_read16(hw, GMAC_IRQ_SRC);
+ skge_read16(hw, SK_REG(port, GMAC_IRQ_SRC));
- spin_lock_bh(&hw->phy_lock);
yukon_init(hw, port);
- spin_unlock_bh(&hw->phy_lock);
/* MIB clear */
reg = gma_read16(hw, port, GM_PHY_ADDR);
/* Configure Rx MAC FIFO */
skge_write16(hw, SK_REG(port, RX_GMF_FL_MSK), RX_FF_FL_DEF_MSK);
reg = GMF_OPER_ON | GMF_RX_F_FL_ON;
- if (hw->chip_id == CHIP_ID_YUKON_LITE &&
- hw->chip_rev == CHIP_REV_YU_LITE_A3)
+
+ /* disable Rx GMAC FIFO Flush for YUKON-Lite Rev. A0 only */
+ if (is_yukon_lite_a0(hw))
reg &= ~GMF_RX_F_FL_ON;
+
skge_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_CLR);
skge_write16(hw, SK_REG(port, RX_GMF_CTRL_T), reg);
- skge_write16(hw, SK_REG(port, RX_GMF_FL_THR), RX_GMF_FL_THR_DEF);
+ /*
+ * because Pause Packet Truncation in GMAC is not working
+ * we have to increase the Flush Threshold to 64 bytes
+ * in order to flush pause packets in Rx FIFO on Yukon-1
+ */
+ skge_write16(hw, SK_REG(port, RX_GMF_FL_THR), RX_GMF_FL_THR_DEF+1);
/* Configure Tx MAC FIFO */
skge_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_CLR);
skge_write16(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_OPER_ON);
}
+/* Go into power down mode */
+static void yukon_suspend(struct skge_hw *hw, int port)
+{
+ u16 ctrl;
+
+ ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
+ ctrl |= PHY_M_PC_POL_R_DIS;
+ gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
+
+ ctrl = gm_phy_read(hw, port, PHY_MARV_CTRL);
+ ctrl |= PHY_CT_RESET;
+ gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
+
+ /* switch IEEE compatible power down mode on */
+ ctrl = gm_phy_read(hw, port, PHY_MARV_CTRL);
+ ctrl |= PHY_CT_PDOWN;
+ gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
+}
+
static void yukon_stop(struct skge_port *skge)
{
struct skge_hw *hw = skge->hw;
int port = skge->port;
- if (hw->chip_id == CHIP_ID_YUKON_LITE &&
- hw->chip_rev == CHIP_REV_YU_LITE_A3) {
- skge_write32(hw, B2_GP_IO,
- skge_read32(hw, B2_GP_IO) | GP_DIR_9 | GP_IO_9);
- }
+ skge_write8(hw, SK_REG(port, GMAC_IRQ_MSK), 0);
+ yukon_reset(hw, port);
gma_write16(hw, port, GM_GP_CTRL,
gma_read16(hw, port, GM_GP_CTRL)
- & ~(GM_GPCR_RX_ENA|GM_GPCR_RX_ENA));
+ & ~(GM_GPCR_TX_ENA|GM_GPCR_RX_ENA));
gma_read16(hw, port, GM_GP_CTRL);
+ yukon_suspend(hw, port);
+
/* set GPHY Control reset */
- gma_write32(hw, port, GPHY_CTRL, GPC_RST_SET);
- gma_write32(hw, port, GMAC_CTRL, GMC_RST_SET);
+ skge_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET);
+ skge_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_SET);
}
static void yukon_get_stats(struct skge_port *skge, u64 *data)
if (status & GM_IS_RX_FF_OR) {
++skge->net_stats.rx_fifo_errors;
- gma_write8(hw, port, RX_GMF_CTRL_T, GMF_CLI_RX_FO);
+ skge_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_CLI_RX_FO);
}
+
if (status & GM_IS_TX_FF_UR) {
++skge->net_stats.tx_fifo_errors;
- gma_write8(hw, port, TX_GMF_CTRL_T, GMF_CLI_TX_FU);
+ skge_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_CLI_TX_FU);
}
}
int port = skge->port;
u16 reg;
- pr_debug("yukon_link_up\n");
-
/* Enable Transmit FIFO Underrun */
- skge_write8(hw, GMAC_IRQ_MSK, GMAC_DEF_MSK);
+ skge_write8(hw, SK_REG(port, GMAC_IRQ_MSK), GMAC_DEF_MSK);
reg = gma_read16(hw, port, GM_GP_CTRL);
if (skge->duplex == DUPLEX_FULL || skge->autoneg == AUTONEG_ENABLE)
reg |= GM_GPCR_RX_ENA | GM_GPCR_TX_ENA;
gma_write16(hw, port, GM_GP_CTRL, reg);
- gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK);
+ gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_DEF_MSK);
skge_link_up(skge);
}
{
struct skge_hw *hw = skge->hw;
int port = skge->port;
+ u16 ctrl;
- pr_debug("yukon_link_down\n");
gm_phy_write(hw, port, PHY_MARV_INT_MASK, 0);
- gm_phy_write(hw, port, GM_GP_CTRL,
- gm_phy_read(hw, port, GM_GP_CTRL)
- & ~(GM_GPCR_RX_ENA | GM_GPCR_TX_ENA));
+
+ ctrl = gma_read16(hw, port, GM_GP_CTRL);
+ ctrl &= ~(GM_GPCR_RX_ENA | GM_GPCR_TX_ENA);
+ gma_write16(hw, port, GM_GP_CTRL, ctrl);
if (skge->flow_control == FLOW_MODE_REM_SEND) {
/* restore Asymmetric Pause bit */
/* XXX restart autonegotiation? */
}
+static void skge_phy_reset(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+
+ netif_stop_queue(skge->netdev);
+ netif_carrier_off(skge->netdev);
+
+ spin_lock_bh(&hw->phy_lock);
+ if (hw->chip_id == CHIP_ID_GENESIS) {
+ genesis_reset(hw, port);
+ genesis_mac_init(hw, port);
+ } else {
+ yukon_reset(hw, port);
+ yukon_init(hw, port);
+ }
+ spin_unlock_bh(&hw->phy_lock);
+}
+
+/* Basic MII support */
+static int skge_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
+{
+ struct mii_ioctl_data *data = if_mii(ifr);
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ int err = -EOPNOTSUPP;
+
+ if (!netif_running(dev))
+ return -ENODEV; /* Phy still in reset */
+
+ switch(cmd) {
+ case SIOCGMIIPHY:
+ data->phy_id = hw->phy_addr;
+
+ /* fallthru */
+ case SIOCGMIIREG: {
+ u16 val = 0;
+ spin_lock_bh(&hw->phy_lock);
+ if (hw->chip_id == CHIP_ID_GENESIS)
+ err = __xm_phy_read(hw, skge->port, data->reg_num & 0x1f, &val);
+ else
+ err = __gm_phy_read(hw, skge->port, data->reg_num & 0x1f, &val);
+ spin_unlock_bh(&hw->phy_lock);
+ data->val_out = val;
+ break;
+ }
+
+ case SIOCSMIIREG:
+ if (!capable(CAP_NET_ADMIN))
+ return -EPERM;
+
+ spin_lock_bh(&hw->phy_lock);
+ if (hw->chip_id == CHIP_ID_GENESIS)
+ err = xm_phy_write(hw, skge->port, data->reg_num & 0x1f,
+ data->val_in);
+ else
+ err = gm_phy_write(hw, skge->port, data->reg_num & 0x1f,
+ data->val_in);
+ spin_unlock_bh(&hw->phy_lock);
+ break;
+ }
+ return err;
+}
+
static void skge_ramset(struct skge_hw *hw, u16 q, u32 start, size_t len)
{
u32 end;
if (netif_msg_ifup(skge))
printk(KERN_INFO PFX "%s: enabling interface\n", dev->name);
+ if (dev->mtu > RX_BUF_SIZE)
+ skge->rx_buf_size = dev->mtu + ETH_HLEN + NET_IP_ALIGN;
+ else
+ skge->rx_buf_size = RX_BUF_SIZE;
+
+
rx_size = skge->rx_ring.count * sizeof(struct skge_rx_desc);
tx_size = skge->tx_ring.count * sizeof(struct skge_tx_desc);
skge->mem_size = tx_size + rx_size;
if ((err = skge_ring_alloc(&skge->rx_ring, skge->mem, skge->dma)))
goto free_pci_mem;
- if (skge_rx_fill(skge))
+ err = skge_rx_fill(skge);
+ if (err)
goto free_rx_ring;
if ((err = skge_ring_alloc(&skge->tx_ring, skge->mem + rx_size,
hw->intr_mask |= portirqmask[port];
skge_write32(hw, B0_IMSK, hw->intr_mask);
- /* Initialze MAC */
+ /* Initialize MAC */
+ spin_lock_bh(&hw->phy_lock);
if (hw->chip_id == CHIP_ID_GENESIS)
genesis_mac_init(hw, port);
else
yukon_mac_init(hw, port);
+ spin_unlock_bh(&hw->phy_lock);
/* Configure RAMbuffers */
chunk = hw->ram_size / ((hw->ports + 1)*2);
/* Start receiver BMU */
wmb();
skge_write8(hw, Q_ADDR(rxqaddr[port], Q_CSR), CSR_START | CSR_IRQ_CL_F);
+ skge_led(skge, LED_MODE_ON);
- pr_debug("skge_up completed\n");
return 0;
free_rx_ring:
kfree(skge->rx_ring.start);
free_pci_mem:
pci_free_consistent(hw->pdev, skge->mem_size, skge->mem, skge->dma);
+ skge->mem = NULL;
return err;
}
struct skge_hw *hw = skge->hw;
int port = skge->port;
+ if (skge->mem == NULL)
+ return 0;
+
if (netif_msg_ifdown(skge))
printk(KERN_INFO PFX "%s: disabling interface\n", dev->name);
netif_stop_queue(dev);
- del_timer_sync(&skge->led_blink);
+ skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG), LED_OFF);
+ if (hw->chip_id == CHIP_ID_GENESIS)
+ genesis_stop(skge);
+ else
+ yukon_stop(skge);
+
+ hw->intr_mask &= ~portirqmask[skge->port];
+ skge_write32(hw, B0_IMSK, hw->intr_mask);
/* Stop transmitter */
skge_write8(hw, Q_ADDR(txqaddr[port], Q_CSR), CSR_STOP);
skge_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL),
RB_RST_SET|RB_DIS_OP_MD);
- if (hw->chip_id == CHIP_ID_GENESIS)
- genesis_stop(skge);
- else
- yukon_stop(skge);
/* Disable Force Sync bit and Enable Alloc bit */
skge_write8(hw, SK_REG(port, TXA_CTRL),
if (hw->chip_id == CHIP_ID_GENESIS) {
skge_write8(hw, SK_REG(port, TX_MFF_CTRL2), MFF_RST_SET);
skge_write8(hw, SK_REG(port, RX_MFF_CTRL2), MFF_RST_SET);
- skge_write8(hw, SK_REG(port, TX_LED_CTRL), LED_STOP);
- skge_write8(hw, SK_REG(port, RX_LED_CTRL), LED_STOP);
} else {
skge_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET);
skge_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_SET);
}
- /* turn off led's */
- skge_write16(hw, B0_LED, LED_STAT_OFF);
+ skge_led(skge, LED_MODE_OFF);
skge_tx_clean(skge);
skge_rx_clean(skge);
kfree(skge->rx_ring.start);
kfree(skge->tx_ring.start);
pci_free_consistent(hw->pdev, skge->mem_size, skge->mem, skge->dma);
+ skge->mem = NULL;
return 0;
}
}
if (unlikely(skge->tx_avail < skb_shinfo(skb)->nr_frags +1)) {
- netif_stop_queue(dev);
- spin_unlock_irqrestore(&skge->tx_lock, flags);
+ if (!netif_queue_stopped(dev)) {
+ netif_stop_queue(dev);
- printk(KERN_WARNING PFX "%s: ring full when queue awake!\n",
- dev->name);
+ printk(KERN_WARNING PFX "%s: ring full when queue awake!\n",
+ dev->name);
+ }
+ spin_unlock_irqrestore(&skge->tx_lock, flags);
return NETDEV_TX_BUSY;
}
td->dma_hi = map >> 32;
if (skb->ip_summed == CHECKSUM_HW) {
- const struct iphdr *ip
- = (const struct iphdr *) (skb->data + ETH_HLEN);
int offset = skb->h.raw - skb->data;
/* This seems backwards, but it is what the sk98lin
* does. Looks like hardware is wrong?
*/
- if (ip->protocol == IPPROTO_UDP
+ if (skb->h.ipiph->protocol == IPPROTO_UDP
&& hw->chip_rev == 0 && hw->chip_id == CHIP_ID_YUKON)
control = BMU_TCP_CHECK;
else
static inline void skge_tx_free(struct skge_hw *hw, struct skge_element *e)
{
+ /* This ring element can be skb or fragment */
if (e->skb) {
pci_unmap_single(hw->pdev,
pci_unmap_addr(e, mapaddr),
static int skge_change_mtu(struct net_device *dev, int new_mtu)
{
- int err = 0;
+ int err;
if (new_mtu < ETH_ZLEN || new_mtu > ETH_JUMBO_MTU)
return -EINVAL;
+ if (!netif_running(dev)) {
+ dev->mtu = new_mtu;
+ return 0;
+ }
+
+ skge_down(dev);
+
dev->mtu = new_mtu;
- if (netif_running(dev)) {
- skge_down(dev);
- skge_up(dev);
- }
+ err = skge_up(dev);
+ if (err)
+ dev_close(dev);
return err;
}
u32 mode;
u8 filter[8];
- pr_debug("genesis_set_multicast flags=%x count=%d\n", dev->flags, dev->mc_count);
-
mode = xm_read32(hw, port, XM_MODE);
mode |= XM_MD_ENA_HASH;
if (dev->flags & IFF_PROMISC)
reg = gma_read16(hw, port, GM_RX_CTRL);
reg |= GM_RXCR_UCF_ENA;
- if (dev->flags & IFF_PROMISC) /* promiscious */
+ if (dev->flags & IFF_PROMISC) /* promiscuous */
reg &= ~(GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA);
else if (dev->flags & IFF_ALLMULTI) /* all multicast */
memset(filter, 0xff, sizeof(filter));
gma_write16(hw, port, GM_RX_CTRL, reg);
}
+static inline u16 phy_length(const struct skge_hw *hw, u32 status)
+{
+ if (hw->chip_id == CHIP_ID_GENESIS)
+ return status >> XMR_FS_LEN_SHIFT;
+ else
+ return status >> GMR_FS_LEN_SHIFT;
+}
+
static inline int bad_phy_status(const struct skge_hw *hw, u32 status)
{
if (hw->chip_id == CHIP_ID_GENESIS)
(status & GMR_FS_RX_OK) == 0;
}
-static void skge_rx_error(struct skge_port *skge, int slot,
- u32 control, u32 status)
+
+/* Get receive buffer from descriptor.
+ * Handles copy of small buffers and reallocation failures
+ */
+static inline struct sk_buff *skge_rx_get(struct skge_port *skge,
+ struct skge_element *e,
+ u32 control, u32 status, u16 csum)
{
- if (netif_msg_rx_err(skge))
- printk(KERN_DEBUG PFX "%s: rx err, slot %d control 0x%x status 0x%x\n",
- skge->netdev->name, slot, control, status);
+ struct sk_buff *skb;
+ u16 len = control & BMU_BBC;
+
+ if (unlikely(netif_msg_rx_status(skge)))
+ printk(KERN_DEBUG PFX "%s: rx slot %td status 0x%x len %d\n",
+ skge->netdev->name, e - skge->rx_ring.start,
+ status, len);
+
+ if (len > skge->rx_buf_size)
+ goto error;
+
+ if ((control & (BMU_EOF|BMU_STF)) != (BMU_STF|BMU_EOF))
+ goto error;
+
+ if (bad_phy_status(skge->hw, status))
+ goto error;
+
+ if (phy_length(skge->hw, status) != len)
+ goto error;
+
+ if (len < RX_COPY_THRESHOLD) {
+ skb = dev_alloc_skb(len + 2);
+ if (!skb)
+ goto resubmit;
+
+ skb_reserve(skb, 2);
+ pci_dma_sync_single_for_cpu(skge->hw->pdev,
+ pci_unmap_addr(e, mapaddr),
+ len, PCI_DMA_FROMDEVICE);
+ memcpy(skb->data, e->skb->data, len);
+ pci_dma_sync_single_for_device(skge->hw->pdev,
+ pci_unmap_addr(e, mapaddr),
+ len, PCI_DMA_FROMDEVICE);
+ skge_rx_reuse(e, skge->rx_buf_size);
+ } else {
+ struct sk_buff *nskb;
+ nskb = dev_alloc_skb(skge->rx_buf_size + NET_IP_ALIGN);
+ if (!nskb)
+ goto resubmit;
- if ((control & (BMU_EOF|BMU_STF)) != (BMU_STF|BMU_EOF)
- || (control & BMU_BBC) > skge->netdev->mtu + VLAN_ETH_HLEN)
- skge->net_stats.rx_length_errors++;
- else {
- if (skge->hw->chip_id == CHIP_ID_GENESIS) {
- if (status & (XMR_FS_RUNT|XMR_FS_LNG_ERR))
- skge->net_stats.rx_length_errors++;
- if (status & XMR_FS_FRA_ERR)
- skge->net_stats.rx_frame_errors++;
- if (status & XMR_FS_FCS_ERR)
- skge->net_stats.rx_crc_errors++;
- } else {
- if (status & (GMR_FS_LONG_ERR|GMR_FS_UN_SIZE))
- skge->net_stats.rx_length_errors++;
- if (status & GMR_FS_FRAGMENT)
- skge->net_stats.rx_frame_errors++;
- if (status & GMR_FS_CRC_ERR)
- skge->net_stats.rx_crc_errors++;
- }
+ pci_unmap_single(skge->hw->pdev,
+ pci_unmap_addr(e, mapaddr),
+ pci_unmap_len(e, maplen),
+ PCI_DMA_FROMDEVICE);
+ skb = e->skb;
+ prefetch(skb->data);
+ skge_rx_setup(skge, e, nskb, skge->rx_buf_size);
}
+
+ skb_put(skb, len);
+ skb->dev = skge->netdev;
+ if (skge->rx_csum) {
+ skb->csum = csum;
+ skb->ip_summed = CHECKSUM_HW;
+ }
+
+ skb->protocol = eth_type_trans(skb, skge->netdev);
+
+ return skb;
+error:
+
+ if (netif_msg_rx_err(skge))
+ printk(KERN_DEBUG PFX "%s: rx err, slot %td control 0x%x status 0x%x\n",
+ skge->netdev->name, e - skge->rx_ring.start,
+ control, status);
+
+ if (skge->hw->chip_id == CHIP_ID_GENESIS) {
+ if (status & (XMR_FS_RUNT|XMR_FS_LNG_ERR))
+ skge->net_stats.rx_length_errors++;
+ if (status & XMR_FS_FRA_ERR)
+ skge->net_stats.rx_frame_errors++;
+ if (status & XMR_FS_FCS_ERR)
+ skge->net_stats.rx_crc_errors++;
+ } else {
+ if (status & (GMR_FS_LONG_ERR|GMR_FS_UN_SIZE))
+ skge->net_stats.rx_length_errors++;
+ if (status & GMR_FS_FRAGMENT)
+ skge->net_stats.rx_frame_errors++;
+ if (status & GMR_FS_CRC_ERR)
+ skge->net_stats.rx_crc_errors++;
+ }
+
+resubmit:
+ skge_rx_reuse(e, skge->rx_buf_size);
+ return NULL;
}
+
static int skge_poll(struct net_device *dev, int *budget)
{
struct skge_port *skge = netdev_priv(dev);
struct skge_element *e;
unsigned int to_do = min(dev->quota, *budget);
unsigned int work_done = 0;
- int done;
-
- pr_debug("skge_poll\n");
- for (e = ring->to_clean; e != ring->to_use && work_done < to_do;
- e = e->next) {
+ for (e = ring->to_clean; prefetch(e->next), work_done < to_do; e = e->next) {
struct skge_rx_desc *rd = e->desc;
- struct sk_buff *skb = e->skb;
- u32 control, len, status;
+ struct sk_buff *skb;
+ u32 control;
rmb();
control = rd->control;
if (control & BMU_OWN)
break;
- len = control & BMU_BBC;
- e->skb = NULL;
-
- pci_unmap_single(hw->pdev,
- pci_unmap_addr(e, mapaddr),
- pci_unmap_len(e, maplen),
- PCI_DMA_FROMDEVICE);
-
- status = rd->status;
- if ((control & (BMU_EOF|BMU_STF)) != (BMU_STF|BMU_EOF)
- || len > dev->mtu + VLAN_ETH_HLEN
- || bad_phy_status(hw, status)) {
- skge_rx_error(skge, e - ring->start, control, status);
- dev_kfree_skb(skb);
- continue;
- }
-
- if (netif_msg_rx_status(skge))
- printk(KERN_DEBUG PFX "%s: rx slot %td status 0x%x len %d\n",
- dev->name, e - ring->start, rd->status, len);
-
- skb_put(skb, len);
- skb->protocol = eth_type_trans(skb, dev);
-
- if (skge->rx_csum) {
- skb->csum = le16_to_cpu(rd->csum2);
- skb->ip_summed = CHECKSUM_HW;
- }
-
- dev->last_rx = jiffies;
- netif_receive_skb(skb);
+ skb = skge_rx_get(skge, e, control, rd->status,
+ le16_to_cpu(rd->csum2));
+ if (likely(skb)) {
+ dev->last_rx = jiffies;
+ netif_receive_skb(skb);
- ++work_done;
+ ++work_done;
+ } else
+ skge_rx_reuse(e, skge->rx_buf_size);
}
ring->to_clean = e;
- *budget -= work_done;
- dev->quota -= work_done;
- done = work_done < to_do;
-
- if (skge_rx_fill(skge))
- done = 0;
-
/* restart receiver */
wmb();
skge_write8(hw, Q_ADDR(rxqaddr[skge->port], Q_CSR),
CSR_START | CSR_IRQ_CL_F);
- if (done) {
- local_irq_disable();
- __netif_rx_complete(dev);
- hw->intr_mask |= portirqmask[skge->port];
- skge_write32(hw, B0_IMSK, hw->intr_mask);
- local_irq_enable();
- }
+ *budget -= work_done;
+ dev->quota -= work_done;
+
+ if (work_done >= to_do)
+ return 1; /* not done */
- return !done;
+ netif_rx_complete(dev);
+ hw->intr_mask |= portirqmask[skge->port];
+ skge_write32(hw, B0_IMSK, hw->intr_mask);
+ skge_read32(hw, B0_IMSK);
+
+ return 0;
}
static inline void skge_tx_intr(struct net_device *dev)
struct skge_element *e;
spin_lock(&skge->tx_lock);
- for (e = ring->to_clean; e != ring->to_use; e = e->next) {
+ for (e = ring->to_clean; prefetch(e->next), e != ring->to_use; e = e->next) {
struct skge_tx_desc *td = e->desc;
u32 control;
spin_unlock(&skge->tx_lock);
}
+/* Parity errors seem to happen when Genesis is connected to a switch
+ * with no other ports present. Heartbeat error??
+ */
static void skge_mac_parity(struct skge_hw *hw, int port)
{
- printk(KERN_ERR PFX "%s: mac data parity error\n",
- hw->dev[port] ? hw->dev[port]->name
- : (port == 0 ? "(port A)": "(port B"));
+ struct net_device *dev = hw->dev[port];
+
+ if (dev) {
+ struct skge_port *skge = netdev_priv(dev);
+ ++skge->net_stats.tx_heartbeat_errors;
+ }
if (hw->chip_id == CHIP_ID_GENESIS)
skge_write16(hw, SK_REG(port, TX_MFF_CTRL1),
if (hw->chip_id == CHIP_ID_GENESIS) {
/* clear xmac errors */
if (hwstatus & (IS_NO_STAT_M1|IS_NO_TIST_M1))
- skge_write16(hw, SK_REG(0, RX_MFF_CTRL1), MFF_CLR_INSTAT);
+ skge_write16(hw, RX_MFF_CTRL1, MFF_CLR_INSTAT);
if (hwstatus & (IS_NO_STAT_M2|IS_NO_TIST_M2))
- skge_write16(hw, SK_REG(0, RX_MFF_CTRL2), MFF_CLR_INSTAT);
+ skge_write16(hw, RX_MFF_CTRL2, MFF_CLR_INSTAT);
} else {
/* Timestamp (unused) overflow */
if (hwstatus & IS_IRQ_TIST_OV)
skge_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ);
-
- if (hwstatus & IS_IRQ_SENSOR) {
- /* no sensors on 32-bit Yukon */
- if (!(skge_read16(hw, B0_CTST) & CS_BUS_SLOT_SZ)) {
- printk(KERN_ERR PFX "ignoring bogus sensor interrups\n");
- skge_write32(hw, B0_HWE_IMSK,
- IS_ERR_MSK & ~IS_IRQ_SENSOR);
- } else
- printk(KERN_WARNING PFX "sensor interrupt\n");
- }
-
-
}
if (hwstatus & IS_RAM_RD_PAR) {
skge_pci_clear(hw);
+ /* if error still set then just ignore it */
hwstatus = skge_read32(hw, B0_HWE_ISRC);
if (hwstatus & IS_IRQ_STAT) {
- printk(KERN_WARNING PFX "IRQ status %x: still set ignoring hardware errors\n",
+ pr_debug("IRQ status %x: still set ignoring hardware errors\n",
hwstatus);
hw->intr_mask &= ~IS_HW_ERR;
}
}
/*
- * Interrrupt from PHY are handled in tasklet (soft irq)
+ * Interrupt from PHY are handled in tasklet (soft irq)
* because accessing phy registers requires spin wait which might
* cause excess interrupt latency.
*/
local_irq_enable();
}
+static inline void skge_wakeup(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+
+ prefetch(skge->rx_ring.to_clean);
+ netif_rx_schedule(dev);
+}
+
static irqreturn_t skge_intr(int irq, void *dev_id, struct pt_regs *regs)
{
struct skge_hw *hw = dev_id;
status &= hw->intr_mask;
if (status & IS_R1_F) {
hw->intr_mask &= ~IS_R1_F;
- netif_rx_schedule(hw->dev[0]);
+ skge_wakeup(hw->dev[0]);
}
if (status & IS_R2_F) {
hw->intr_mask &= ~IS_R2_F;
- netif_rx_schedule(hw->dev[1]);
+ skge_wakeup(hw->dev[1]);
}
if (status & IS_XA1_F)
if (status & IS_XA2_F)
skge_tx_intr(hw->dev[1]);
+ if (status & IS_PA_TO_RX1) {
+ struct skge_port *skge = netdev_priv(hw->dev[0]);
+ ++skge->net_stats.rx_over_errors;
+ skge_write16(hw, B3_PA_CTRL, PA_CLR_TO_RX1);
+ }
+
+ if (status & IS_PA_TO_RX2) {
+ struct skge_port *skge = netdev_priv(hw->dev[1]);
+ ++skge->net_stats.rx_over_errors;
+ skge_write16(hw, B3_PA_CTRL, PA_CLR_TO_RX2);
+ }
+
+ if (status & IS_PA_TO_TX1)
+ skge_write16(hw, B3_PA_CTRL, PA_CLR_TO_TX1);
+
+ if (status & IS_PA_TO_TX2)
+ skge_write16(hw, B3_PA_CTRL, PA_CLR_TO_TX2);
+
if (status & IS_MAC1)
skge_mac_intr(hw, 0);
static int skge_set_mac_address(struct net_device *dev, void *p)
{
struct skge_port *skge = netdev_priv(dev);
- struct sockaddr *addr = p;
- int err = 0;
+ struct skge_hw *hw = skge->hw;
+ unsigned port = skge->port;
+ const struct sockaddr *addr = p;
if (!is_valid_ether_addr(addr->sa_data))
return -EADDRNOTAVAIL;
- skge_down(dev);
+ spin_lock_bh(&hw->phy_lock);
memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN);
- memcpy_toio(skge->hw->regs + B2_MAC_1 + skge->port*8,
+ memcpy_toio(hw->regs + B2_MAC_1 + port*8,
dev->dev_addr, ETH_ALEN);
- memcpy_toio(skge->hw->regs + B2_MAC_2 + skge->port*8,
+ memcpy_toio(hw->regs + B2_MAC_2 + port*8,
dev->dev_addr, ETH_ALEN);
- if (dev->flags & IFF_UP)
- err = skge_up(dev);
- return err;
+
+ if (hw->chip_id == CHIP_ID_GENESIS)
+ xm_outaddr(hw, port, XM_SA, dev->dev_addr);
+ else {
+ gma_set_addr(hw, port, GM_SRC_ADDR_1L, dev->dev_addr);
+ gma_set_addr(hw, port, GM_SRC_ADDR_2L, dev->dev_addr);
+ }
+ spin_unlock_bh(&hw->phy_lock);
+
+ return 0;
}
static const struct {
*/
static int skge_reset(struct skge_hw *hw)
{
+ u32 reg;
u16 ctst;
- u8 t8, mac_cfg;
+ u8 t8, mac_cfg, pmd_type, phy_type;
int i;
ctst = skge_read16(hw, B0_CTST);
ctst & (CS_CLK_RUN_HOT|CS_CLK_RUN_RST|CS_CLK_RUN_ENA));
hw->chip_id = skge_read8(hw, B2_CHIP_ID);
- hw->phy_type = skge_read8(hw, B2_E_1) & 0xf;
- hw->pmd_type = skge_read8(hw, B2_PMD_TYP);
+ phy_type = skge_read8(hw, B2_E_1) & 0xf;
+ pmd_type = skge_read8(hw, B2_PMD_TYP);
+ hw->copper = (pmd_type == 'T' || pmd_type == '1');
switch (hw->chip_id) {
case CHIP_ID_GENESIS:
- switch (hw->phy_type) {
+ switch (phy_type) {
case SK_PHY_BCOM:
hw->phy_addr = PHY_ADDR_BCOM;
break;
default:
printk(KERN_ERR PFX "%s: unsupported phy type 0x%x\n",
- pci_name(hw->pdev), hw->phy_type);
+ pci_name(hw->pdev), phy_type);
return -EOPNOTSUPP;
}
break;
case CHIP_ID_YUKON:
case CHIP_ID_YUKON_LITE:
case CHIP_ID_YUKON_LP:
- if (hw->phy_type < SK_PHY_MARV_COPPER && hw->pmd_type != 'S')
- hw->phy_type = SK_PHY_MARV_COPPER;
+ if (phy_type < SK_PHY_MARV_COPPER && pmd_type != 'S')
+ hw->copper = 1;
hw->phy_addr = PHY_ADDR_MARV;
- if (!iscopper(hw))
- hw->phy_type = SK_PHY_MARV_FIBER;
-
break;
default:
else
hw->ram_size = t8 * 4096;
+ hw->intr_mask = IS_HW_ERR | IS_EXT_REG;
if (hw->chip_id == CHIP_ID_GENESIS)
genesis_init(hw);
else {
/* switch power to VCC (WA for VAUX problem) */
skge_write8(hw, B0_POWER_CTRL,
PC_VAUX_ENA | PC_VCC_ENA | PC_VAUX_OFF | PC_VCC_ON);
+
+ /* avoid boards with stuck Hardware error bits */
+ if ((skge_read32(hw, B0_ISRC) & IS_HW_ERR) &&
+ (skge_read32(hw, B0_HWE_ISRC) & IS_IRQ_SENSOR)) {
+ printk(KERN_WARNING PFX "stuck hardware sensor bit\n");
+ hw->intr_mask &= ~IS_HW_ERR;
+ }
+
+ /* Clear PHY COMA */
+ skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
+ pci_read_config_dword(hw->pdev, PCI_DEV_REG1, ®);
+ reg &= ~PCI_PHY_COMA;
+ pci_write_config_dword(hw->pdev, PCI_DEV_REG1, reg);
+ skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
+
+
for (i = 0; i < hw->ports; i++) {
skge_write16(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_SET);
skge_write16(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_CLR);
skge_write32(hw, B2_IRQM_INI, skge_usecs2clk(hw, 100));
skge_write32(hw, B2_IRQM_CTRL, TIM_START);
- hw->intr_mask = IS_HW_ERR | IS_EXT_REG;
skge_write32(hw, B0_IMSK, hw->intr_mask);
- if (hw->chip_id != CHIP_ID_GENESIS)
- skge_write8(hw, GMAC_IRQ_MSK, 0);
-
spin_lock_bh(&hw->phy_lock);
for (i = 0; i < hw->ports; i++) {
if (hw->chip_id == CHIP_ID_GENESIS)
SET_NETDEV_DEV(dev, &hw->pdev->dev);
dev->open = skge_up;
dev->stop = skge_down;
+ dev->do_ioctl = skge_ioctl;
dev->hard_start_xmit = skge_xmit_frame;
dev->get_stats = skge_get_stats;
if (hw->chip_id == CHIP_ID_GENESIS)
spin_lock_init(&skge->tx_lock);
- init_timer(&skge->led_blink);
- skge->led_blink.function = skge_blink_timer;
- skge->led_blink.data = (unsigned long) skge;
-
if (hw->chip_id != CHIP_ID_GENESIS) {
dev->features |= NETIF_F_IP_CSUM | NETIF_F_SG;
skge->rx_csum = 1;
/* read the mac address */
memcpy_fromio(dev->dev_addr, hw->regs + B2_MAC_1 + port*8, ETH_ALEN);
+ memcpy(dev->perm_addr, dev->dev_addr, dev->addr_len);
/* device is off until link detection */
netif_carrier_off(dev);
}
#ifdef __BIG_ENDIAN
- /* byte swap decriptors in hardware */
+ /* byte swap descriptors in hardware */
{
u32 reg;
#endif
err = -ENOMEM;
- hw = kmalloc(sizeof(*hw), GFP_KERNEL);
+ hw = kzalloc(sizeof(*hw), GFP_KERNEL);
if (!hw) {
printk(KERN_ERR PFX "%s: cannot allocate hardware struct\n",
pci_name(pdev));
goto err_out_free_regions;
}
- memset(hw, 0, sizeof(*hw));
hw->pdev = pdev;
spin_lock_init(&hw->phy_lock);
tasklet_init(&hw->ext_tasklet, skge_extirq, (unsigned long) hw);
if (err)
goto err_out_free_irq;
- printk(KERN_INFO PFX "addr 0x%lx irq %d chip %s rev %d\n",
+ printk(KERN_INFO PFX DRV_VERSION " addr 0x%lx irq %d chip %s rev %d\n",
pci_resource_start(pdev, 0), pdev->irq,
skge_board_name(hw), hw->chip_rev);
dev0 = hw->dev[0];
unregister_netdev(dev0);
+ skge_write32(hw, B0_IMSK, 0);
+ skge_write16(hw, B0_LED, LED_STAT_OFF);
+ skge_pci_clear(hw);
+ skge_write8(hw, B0_CTST, CS_RST_SET);
+
tasklet_kill(&hw->ext_tasklet);
free_irq(pdev->irq, hw);
if (dev1)
free_netdev(dev1);
free_netdev(dev0);
- skge_write16(hw, B0_LED, LED_STAT_OFF);
+
iounmap(hw->regs);
kfree(hw);
pci_set_drvdata(pdev, NULL);
}
#ifdef CONFIG_PM
-static int skge_suspend(struct pci_dev *pdev, u32 state)
+static int skge_suspend(struct pci_dev *pdev, pm_message_t state)
{
struct skge_hw *hw = pci_get_drvdata(pdev);
int i, wol = 0;
struct skge_port *skge = netdev_priv(dev);
if (netif_running(dev)) {
netif_carrier_off(dev);
- skge_down(dev);
+ if (skge->wol)
+ netif_stop_queue(dev);
+ else
+ skge_down(dev);
}
netif_device_detach(dev);
wol |= skge->wol;
}
pci_save_state(pdev);
- pci_enable_wake(pdev, state, wol);
+ pci_enable_wake(pdev, pci_choose_state(pdev, state), wol);
pci_disable_device(pdev);
pci_set_power_state(pdev, pci_choose_state(pdev, state));
struct net_device *dev = hw->dev[i];
if (dev) {
netif_device_attach(dev);
- if (netif_running(dev))
- skge_up(dev);
+ if (netif_running(dev) && skge_up(dev))
+ dev_close(dev);
}
}
return 0;
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff