* of the original driver such as link fail-over and link management because
* those should be done at higher levels.
*
- * Copyright (C) 2004, Stephen Hemminger <shemminger@osdl.org>
+ * Copyright (C) 2004, 2005 Stephen Hemminger <shemminger@osdl.org>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
+ * the Free Software Foundation; either version 2 of the License.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
-#include <linux/config.h>
+#include <linux/in.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/delay.h>
#include <linux/crc32.h>
#include <linux/dma-mapping.h>
+#include <linux/debugfs.h>
+#include <linux/seq_file.h>
+#include <linux/mii.h>
#include <asm/irq.h>
#include "skge.h"
#define DRV_NAME "skge"
-#define DRV_VERSION "0.6"
+#define DRV_VERSION "1.13"
#define PFX DRV_NAME " "
#define DEFAULT_TX_RING_SIZE 128
#define DEFAULT_RX_RING_SIZE 512
#define MAX_TX_RING_SIZE 1024
+#define TX_LOW_WATER (MAX_SKB_FRAGS + 1)
#define MAX_RX_RING_SIZE 4096
+#define RX_COPY_THRESHOLD 128
+#define RX_BUF_SIZE 1536
#define PHY_RETRIES 1000
#define ETH_JUMBO_MTU 9000
#define TX_WATCHDOG (5 * HZ)
#define NAPI_WEIGHT 64
-#define BLINK_HZ (HZ/4)
-#define LINK_POLL_HZ (HZ/10)
+#define BLINK_MS 250
+#define LINK_HZ HZ
+
+#define SKGE_EEPROM_MAGIC 0x9933aabb
+
MODULE_DESCRIPTION("SysKonnect Gigabit Ethernet driver");
-MODULE_AUTHOR("Stephen Hemminger <shemminger@osdl.org>");
+MODULE_AUTHOR("Stephen Hemminger <shemminger@linux-foundation.org>");
MODULE_LICENSE("GPL");
MODULE_VERSION(DRV_VERSION);
{ PCI_DEVICE(PCI_VENDOR_ID_3COM, PCI_DEVICE_ID_3COM_3C940B) },
{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, PCI_DEVICE_ID_SYSKONNECT_GE) },
{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, PCI_DEVICE_ID_SYSKONNECT_YU) },
- { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9E00) }, /* SK-9Exx */
- { PCI_DEVICE(PCI_VENDOR_ID_DLINK, PCI_DEVICE_ID_DLINK_DGE510T), },
+ { PCI_DEVICE(PCI_VENDOR_ID_DLINK, PCI_DEVICE_ID_DLINK_DGE510T) },
+ { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4b01) }, /* DGE-530T */
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4320) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5005) }, /* Belkin */
{ PCI_DEVICE(PCI_VENDOR_ID_CNET, PCI_DEVICE_ID_CNET_GIGACARD) },
- { PCI_DEVICE(PCI_VENDOR_ID_LINKSYS, PCI_DEVICE_ID_LINKSYS_EG1032) },
{ PCI_DEVICE(PCI_VENDOR_ID_LINKSYS, PCI_DEVICE_ID_LINKSYS_EG1064) },
+ { PCI_VENDOR_ID_LINKSYS, 0x1032, PCI_ANY_ID, 0x0015 },
{ 0 }
};
MODULE_DEVICE_TABLE(pci, skge_id_table);
static int skge_up(struct net_device *dev);
static int skge_down(struct net_device *dev);
-static void skge_tx_clean(struct skge_port *skge);
-static void xm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val);
-static void gm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val);
+static void skge_phy_reset(struct skge_port *skge);
+static void skge_tx_clean(struct net_device *dev);
+static int xm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val);
+static int gm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val);
static void genesis_get_stats(struct skge_port *skge, u64 *data);
static void yukon_get_stats(struct skge_port *skge, u64 *data);
static void yukon_init(struct skge_hw *hw, int port);
-static void yukon_reset(struct skge_hw *hw, int port);
static void genesis_mac_init(struct skge_hw *hw, int port);
-static void genesis_reset(struct skge_hw *hw, int port);
+static void genesis_link_up(struct skge_port *skge);
+static void skge_set_multicast(struct net_device *dev);
+/* Avoid conditionals by using array */
static const int txqaddr[] = { Q_XA1, Q_XA2 };
static const int rxqaddr[] = { Q_R1, Q_R2 };
static const u32 rxirqmask[] = { IS_R1_F, IS_R2_F };
static const u32 txirqmask[] = { IS_XA1_F, IS_XA2_F };
-
-/* Don't need to look at whole 16K.
- * last interesting register is descriptor poll timer.
- */
-#define SKGE_REGS_LEN (29*128)
+static const u32 napimask[] = { IS_R1_F|IS_XA1_F, IS_R2_F|IS_XA2_F };
+static const u32 portmask[] = { IS_PORT_1, IS_PORT_2 };
static int skge_get_regs_len(struct net_device *dev)
{
- return SKGE_REGS_LEN;
+ return 0x4000;
}
/*
- * Returns copy of control register region
- * I/O region is divided into banks and certain regions are unreadable
+ * Returns copy of whole control register region
+ * Note: skip RAM address register because accessing it will
+ * cause bus hangs!
*/
static void skge_get_regs(struct net_device *dev, struct ethtool_regs *regs,
void *p)
{
const struct skge_port *skge = netdev_priv(dev);
- unsigned long offs;
const void __iomem *io = skge->hw->regs;
- static const unsigned long bankmap
- = (1<<0) | (1<<2) | (1<<8) | (1<<9)
- | (1<<12) | (1<<13) | (1<<14) | (1<<15) | (1<<16)
- | (1<<17) | (1<<20) | (1<<21) | (1<<22) | (1<<23)
- | (1<<24) | (1<<25) | (1<<26) | (1<<27) | (1<<28);
regs->version = 1;
- for (offs = 0; offs < regs->len; offs += 128) {
- u32 len = min_t(u32, 128, regs->len - offs);
+ memset(p, 0, regs->len);
+ memcpy_fromio(p, io, B3_RAM_ADDR);
- if (bankmap & (1<<(offs/128)))
- memcpy_fromio(p + offs, io + offs, len);
- else
- memset(p + offs, 0, len);
- }
+ memcpy_fromio(p + B3_RI_WTO_R1, io + B3_RI_WTO_R1,
+ regs->len - B3_RI_WTO_R1);
+}
+
+/* Wake on Lan only supported on Yukon chips with rev 1 or above */
+static u32 wol_supported(const struct skge_hw *hw)
+{
+ if (hw->chip_id == CHIP_ID_GENESIS)
+ return 0;
+
+ if (hw->chip_id == CHIP_ID_YUKON && hw->chip_rev == 0)
+ return 0;
+
+ return WAKE_MAGIC | WAKE_PHY;
}
-/* Wake on Lan only supported on Yukon chps with rev 1 or above */
-static int wol_supported(const struct skge_hw *hw)
+static void skge_wol_init(struct skge_port *skge)
{
- return !((hw->chip_id == CHIP_ID_GENESIS ||
- (hw->chip_id == CHIP_ID_YUKON && hw->chip_rev == 0)));
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ u16 ctrl;
+
+ skge_write16(hw, B0_CTST, CS_RST_CLR);
+ skge_write16(hw, SK_REG(port, GMAC_LINK_CTRL), GMLC_RST_CLR);
+
+ /* Turn on Vaux */
+ skge_write8(hw, B0_POWER_CTRL,
+ PC_VAUX_ENA | PC_VCC_ENA | PC_VAUX_ON | PC_VCC_OFF);
+
+ /* WA code for COMA mode -- clear PHY reset */
+ if (hw->chip_id == CHIP_ID_YUKON_LITE &&
+ hw->chip_rev >= CHIP_REV_YU_LITE_A3) {
+ u32 reg = skge_read32(hw, B2_GP_IO);
+ reg |= GP_DIR_9;
+ reg &= ~GP_IO_9;
+ skge_write32(hw, B2_GP_IO, reg);
+ }
+
+ skge_write32(hw, SK_REG(port, GPHY_CTRL),
+ GPC_DIS_SLEEP |
+ GPC_HWCFG_M_3 | GPC_HWCFG_M_2 | GPC_HWCFG_M_1 | GPC_HWCFG_M_0 |
+ GPC_ANEG_1 | GPC_RST_SET);
+
+ skge_write32(hw, SK_REG(port, GPHY_CTRL),
+ GPC_DIS_SLEEP |
+ GPC_HWCFG_M_3 | GPC_HWCFG_M_2 | GPC_HWCFG_M_1 | GPC_HWCFG_M_0 |
+ GPC_ANEG_1 | GPC_RST_CLR);
+
+ skge_write32(hw, SK_REG(port, GMAC_CTRL), GMC_RST_CLR);
+
+ /* Force to 10/100 skge_reset will re-enable on resume */
+ gm_phy_write(hw, port, PHY_MARV_AUNE_ADV,
+ PHY_AN_100FULL | PHY_AN_100HALF |
+ PHY_AN_10FULL | PHY_AN_10HALF| PHY_AN_CSMA);
+ /* no 1000 HD/FD */
+ gm_phy_write(hw, port, PHY_MARV_1000T_CTRL, 0);
+ gm_phy_write(hw, port, PHY_MARV_CTRL,
+ PHY_CT_RESET | PHY_CT_SPS_LSB | PHY_CT_ANE |
+ PHY_CT_RE_CFG | PHY_CT_DUP_MD);
+
+
+ /* Set GMAC to no flow control and auto update for speed/duplex */
+ gma_write16(hw, port, GM_GP_CTRL,
+ GM_GPCR_FC_TX_DIS|GM_GPCR_TX_ENA|GM_GPCR_RX_ENA|
+ GM_GPCR_DUP_FULL|GM_GPCR_FC_RX_DIS|GM_GPCR_AU_FCT_DIS);
+
+ /* Set WOL address */
+ memcpy_toio(hw->regs + WOL_REGS(port, WOL_MAC_ADDR),
+ skge->netdev->dev_addr, ETH_ALEN);
+
+ /* Turn on appropriate WOL control bits */
+ skge_write16(hw, WOL_REGS(port, WOL_CTRL_STAT), WOL_CTL_CLEAR_RESULT);
+ ctrl = 0;
+ if (skge->wol & WAKE_PHY)
+ ctrl |= WOL_CTL_ENA_PME_ON_LINK_CHG|WOL_CTL_ENA_LINK_CHG_UNIT;
+ else
+ ctrl |= WOL_CTL_DIS_PME_ON_LINK_CHG|WOL_CTL_DIS_LINK_CHG_UNIT;
+
+ if (skge->wol & WAKE_MAGIC)
+ ctrl |= WOL_CTL_ENA_PME_ON_MAGIC_PKT|WOL_CTL_ENA_MAGIC_PKT_UNIT;
+ else
+ ctrl |= WOL_CTL_DIS_PME_ON_MAGIC_PKT|WOL_CTL_DIS_MAGIC_PKT_UNIT;;
+
+ ctrl |= WOL_CTL_DIS_PME_ON_PATTERN|WOL_CTL_DIS_PATTERN_UNIT;
+ skge_write16(hw, WOL_REGS(port, WOL_CTRL_STAT), ctrl);
+
+ /* block receiver */
+ skge_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET);
}
static void skge_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
{
struct skge_port *skge = netdev_priv(dev);
- wol->supported = wol_supported(skge->hw) ? WAKE_MAGIC : 0;
- wol->wolopts = skge->wol ? WAKE_MAGIC : 0;
+ wol->supported = wol_supported(skge->hw);
+ wol->wolopts = skge->wol;
}
static int skge_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
struct skge_port *skge = netdev_priv(dev);
struct skge_hw *hw = skge->hw;
- if (wol->wolopts != WAKE_MAGIC && wol->wolopts != 0)
+ if ((wol->wolopts & ~wol_supported(hw))
+ || !device_can_wakeup(&hw->pdev->dev))
return -EOPNOTSUPP;
- if (wol->wolopts == WAKE_MAGIC && !wol_supported(hw))
- return -EOPNOTSUPP;
+ skge->wol = wol->wolopts;
- skge->wol = wol->wolopts == WAKE_MAGIC;
+ device_set_wakeup_enable(&hw->pdev->dev, skge->wol);
- if (skge->wol) {
- memcpy_toio(hw->regs + WOL_MAC_ADDR, dev->dev_addr, ETH_ALEN);
+ return 0;
+}
+
+/* Determine supported/advertised modes based on hardware.
+ * Note: ethtool ADVERTISED_xxx == SUPPORTED_xxx
+ */
+static u32 skge_supported_modes(const struct skge_hw *hw)
+{
+ u32 supported;
+
+ if (hw->copper) {
+ supported = SUPPORTED_10baseT_Half
+ | SUPPORTED_10baseT_Full
+ | SUPPORTED_100baseT_Half
+ | SUPPORTED_100baseT_Full
+ | SUPPORTED_1000baseT_Half
+ | SUPPORTED_1000baseT_Full
+ | SUPPORTED_Autoneg| SUPPORTED_TP;
+
+ if (hw->chip_id == CHIP_ID_GENESIS)
+ supported &= ~(SUPPORTED_10baseT_Half
+ | SUPPORTED_10baseT_Full
+ | SUPPORTED_100baseT_Half
+ | SUPPORTED_100baseT_Full);
- skge_write16(hw, WOL_CTRL_STAT,
- WOL_CTL_ENA_PME_ON_MAGIC_PKT |
- WOL_CTL_ENA_MAGIC_PKT_UNIT);
+ else if (hw->chip_id == CHIP_ID_YUKON)
+ supported &= ~SUPPORTED_1000baseT_Half;
} else
- skge_write16(hw, WOL_CTRL_STAT, WOL_CTL_DEFAULT);
+ supported = SUPPORTED_1000baseT_Full | SUPPORTED_1000baseT_Half
+ | SUPPORTED_FIBRE | SUPPORTED_Autoneg;
- return 0;
+ return supported;
}
-
static int skge_get_settings(struct net_device *dev,
struct ethtool_cmd *ecmd)
{
struct skge_hw *hw = skge->hw;
ecmd->transceiver = XCVR_INTERNAL;
+ ecmd->supported = skge_supported_modes(hw);
- if (iscopper(hw)) {
- if (hw->chip_id == CHIP_ID_GENESIS)
- ecmd->supported = SUPPORTED_1000baseT_Full
- | SUPPORTED_1000baseT_Half
- | SUPPORTED_Autoneg | SUPPORTED_TP;
- else {
- ecmd->supported = SUPPORTED_10baseT_Half
- | SUPPORTED_10baseT_Full
- | SUPPORTED_100baseT_Half
- | SUPPORTED_100baseT_Full
- | SUPPORTED_1000baseT_Half
- | SUPPORTED_1000baseT_Full
- | SUPPORTED_Autoneg| SUPPORTED_TP;
-
- if (hw->chip_id == CHIP_ID_YUKON)
- ecmd->supported &= ~SUPPORTED_1000baseT_Half;
-
- else if (hw->chip_id == CHIP_ID_YUKON_FE)
- ecmd->supported &= ~(SUPPORTED_1000baseT_Half
- | SUPPORTED_1000baseT_Full);
- }
-
+ if (hw->copper) {
ecmd->port = PORT_TP;
ecmd->phy_address = hw->phy_addr;
- } else {
- ecmd->supported = SUPPORTED_1000baseT_Full
- | SUPPORTED_FIBRE
- | SUPPORTED_Autoneg;
-
+ } else
ecmd->port = PORT_FIBRE;
- }
ecmd->advertising = skge->advertising;
ecmd->autoneg = skge->autoneg;
return 0;
}
-static u32 skge_modes(const struct skge_hw *hw)
-{
- u32 modes = ADVERTISED_Autoneg
- | ADVERTISED_1000baseT_Full | ADVERTISED_1000baseT_Half
- | ADVERTISED_100baseT_Full | ADVERTISED_100baseT_Half
- | ADVERTISED_10baseT_Full | ADVERTISED_10baseT_Half;
-
- if (iscopper(hw)) {
- modes |= ADVERTISED_TP;
- switch (hw->chip_id) {
- case CHIP_ID_GENESIS:
- modes &= ~(ADVERTISED_100baseT_Full
- | ADVERTISED_100baseT_Half
- | ADVERTISED_10baseT_Full
- | ADVERTISED_10baseT_Half);
- break;
-
- case CHIP_ID_YUKON:
- modes &= ~ADVERTISED_1000baseT_Half;
- break;
-
- case CHIP_ID_YUKON_FE:
- modes &= ~(ADVERTISED_1000baseT_Half|ADVERTISED_1000baseT_Full);
- break;
- }
- } else {
- modes |= ADVERTISED_FIBRE;
- modes &= ~ADVERTISED_1000baseT_Half;
- }
- return modes;
-}
-
static int skge_set_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
{
struct skge_port *skge = netdev_priv(dev);
const struct skge_hw *hw = skge->hw;
+ u32 supported = skge_supported_modes(hw);
+ int err = 0;
if (ecmd->autoneg == AUTONEG_ENABLE) {
- if (ecmd->advertising & skge_modes(hw))
- return -EINVAL;
+ ecmd->advertising = supported;
+ skge->duplex = -1;
+ skge->speed = -1;
} else {
+ u32 setting;
+
switch (ecmd->speed) {
case SPEED_1000:
- if (hw->chip_id == CHIP_ID_YUKON_FE)
+ if (ecmd->duplex == DUPLEX_FULL)
+ setting = SUPPORTED_1000baseT_Full;
+ else if (ecmd->duplex == DUPLEX_HALF)
+ setting = SUPPORTED_1000baseT_Half;
+ else
return -EINVAL;
break;
case SPEED_100:
+ if (ecmd->duplex == DUPLEX_FULL)
+ setting = SUPPORTED_100baseT_Full;
+ else if (ecmd->duplex == DUPLEX_HALF)
+ setting = SUPPORTED_100baseT_Half;
+ else
+ return -EINVAL;
+ break;
+
case SPEED_10:
- if (iscopper(hw) || hw->chip_id == CHIP_ID_GENESIS)
+ if (ecmd->duplex == DUPLEX_FULL)
+ setting = SUPPORTED_10baseT_Full;
+ else if (ecmd->duplex == DUPLEX_HALF)
+ setting = SUPPORTED_10baseT_Half;
+ else
return -EINVAL;
break;
default:
return -EINVAL;
}
+
+ if ((setting & supported) == 0)
+ return -EINVAL;
+
+ skge->speed = ecmd->speed;
+ skge->duplex = ecmd->duplex;
}
skge->autoneg = ecmd->autoneg;
- skge->speed = ecmd->speed;
- skge->duplex = ecmd->duplex;
skge->advertising = ecmd->advertising;
if (netif_running(dev)) {
skge_down(dev);
- skge_up(dev);
+ err = skge_up(dev);
+ if (err) {
+ dev_close(dev);
+ return err;
+ }
}
+
return (0);
}
{ "rx_fcs_error", XM_RXF_FCS_ERR, GM_RXF_FCS_ERR },
};
-static int skge_get_stats_count(struct net_device *dev)
+static int skge_get_sset_count(struct net_device *dev, int sset)
{
- return ARRAY_SIZE(skge_stats);
+ switch (sset) {
+ case ETH_SS_STATS:
+ return ARRAY_SIZE(skge_stats);
+ default:
+ return -EOPNOTSUPP;
+ }
}
static void skge_get_ethtool_stats(struct net_device *dev,
else
yukon_get_stats(skge, data);
- skge->net_stats.tx_bytes = data[0];
- skge->net_stats.rx_bytes = data[1];
- skge->net_stats.tx_packets = data[2] + data[4] + data[6];
- skge->net_stats.rx_packets = data[3] + data[5] + data[7];
- skge->net_stats.multicast = data[5] + data[7];
- skge->net_stats.collisions = data[10];
- skge->net_stats.tx_aborted_errors = data[12];
+ dev->stats.tx_bytes = data[0];
+ dev->stats.rx_bytes = data[1];
+ dev->stats.tx_packets = data[2] + data[4] + data[6];
+ dev->stats.rx_packets = data[3] + data[5] + data[7];
+ dev->stats.multicast = data[3] + data[5];
+ dev->stats.collisions = data[10];
+ dev->stats.tx_aborted_errors = data[12];
- return &skge->net_stats;
+ return &dev->stats;
}
static void skge_get_strings(struct net_device *dev, u32 stringset, u8 *data)
struct ethtool_ringparam *p)
{
struct skge_port *skge = netdev_priv(dev);
+ int err = 0;
if (p->rx_pending == 0 || p->rx_pending > MAX_RX_RING_SIZE ||
- p->tx_pending == 0 || p->tx_pending > MAX_TX_RING_SIZE)
+ p->tx_pending < TX_LOW_WATER || p->tx_pending > MAX_TX_RING_SIZE)
return -EINVAL;
skge->rx_ring.count = p->rx_pending;
if (netif_running(dev)) {
skge_down(dev);
- skge_up(dev);
+ err = skge_up(dev);
+ if (err)
+ dev_close(dev);
}
- return 0;
+ return err;
}
static u32 skge_get_msglevel(struct net_device *netdev)
static int skge_nway_reset(struct net_device *dev)
{
struct skge_port *skge = netdev_priv(dev);
- struct skge_hw *hw = skge->hw;
- int port = skge->port;
if (skge->autoneg != AUTONEG_ENABLE || !netif_running(dev))
return -EINVAL;
- spin_lock_bh(&hw->phy_lock);
- if (hw->chip_id == CHIP_ID_GENESIS) {
- genesis_reset(hw, port);
- genesis_mac_init(hw, port);
- } else {
- yukon_reset(hw, port);
- yukon_init(hw, port);
- }
- spin_unlock_bh(&hw->phy_lock);
+ skge_phy_reset(skge);
return 0;
}
{
struct skge_port *skge = netdev_priv(dev);
- ecmd->tx_pause = (skge->flow_control == FLOW_MODE_LOC_SEND)
- || (skge->flow_control == FLOW_MODE_SYMMETRIC);
- ecmd->rx_pause = (skge->flow_control == FLOW_MODE_REM_SEND)
- || (skge->flow_control == FLOW_MODE_SYMMETRIC);
+ ecmd->rx_pause = (skge->flow_control == FLOW_MODE_SYMMETRIC)
+ || (skge->flow_control == FLOW_MODE_SYM_OR_REM);
+ ecmd->tx_pause = ecmd->rx_pause || (skge->flow_control == FLOW_MODE_LOC_SEND);
- ecmd->autoneg = skge->autoneg;
+ ecmd->autoneg = ecmd->rx_pause || ecmd->tx_pause;
}
static int skge_set_pauseparam(struct net_device *dev,
struct ethtool_pauseparam *ecmd)
{
struct skge_port *skge = netdev_priv(dev);
+ struct ethtool_pauseparam old;
+ int err = 0;
- skge->autoneg = ecmd->autoneg;
- if (ecmd->rx_pause && ecmd->tx_pause)
- skge->flow_control = FLOW_MODE_SYMMETRIC;
- else if (ecmd->rx_pause && !ecmd->tx_pause)
- skge->flow_control = FLOW_MODE_REM_SEND;
- else if (!ecmd->rx_pause && ecmd->tx_pause)
- skge->flow_control = FLOW_MODE_LOC_SEND;
- else
- skge->flow_control = FLOW_MODE_NONE;
+ skge_get_pauseparam(dev, &old);
+
+ if (ecmd->autoneg != old.autoneg)
+ skge->flow_control = ecmd->autoneg ? FLOW_MODE_NONE : FLOW_MODE_SYMMETRIC;
+ else {
+ if (ecmd->rx_pause && ecmd->tx_pause)
+ skge->flow_control = FLOW_MODE_SYMMETRIC;
+ else if (ecmd->rx_pause && !ecmd->tx_pause)
+ skge->flow_control = FLOW_MODE_SYM_OR_REM;
+ else if (!ecmd->rx_pause && ecmd->tx_pause)
+ skge->flow_control = FLOW_MODE_LOC_SEND;
+ else
+ skge->flow_control = FLOW_MODE_NONE;
+ }
if (netif_running(dev)) {
skge_down(dev);
- skge_up(dev);
+ err = skge_up(dev);
+ if (err) {
+ dev_close(dev);
+ return err;
+ }
}
+
return 0;
}
/* Chip internal frequency for clock calculations */
static inline u32 hwkhz(const struct skge_hw *hw)
{
- if (hw->chip_id == CHIP_ID_GENESIS)
- return 53215; /* or: 53.125 MHz */
- else if (hw->chip_id == CHIP_ID_YUKON_EC)
- return 125000; /* or: 125.000 MHz */
- else
- return 78215; /* or: 78.125 MHz */
+ return (hw->chip_id == CHIP_ID_GENESIS) ? 53125 : 78125;
}
-/* Chip hz to microseconds */
+/* Chip HZ to microseconds */
static inline u32 skge_clk2usec(const struct skge_hw *hw, u32 ticks)
{
return (ticks * 1000) / hwkhz(hw);
}
-/* Microseconds to chip hz */
+/* Microseconds to chip HZ */
static inline u32 skge_usecs2clk(const struct skge_hw *hw, u32 usec)
{
return hwkhz(hw) * usec / 1000;
return 0;
}
-static void skge_led_on(struct skge_hw *hw, int port)
+enum led_mode { LED_MODE_OFF, LED_MODE_ON, LED_MODE_TST };
+static void skge_led(struct skge_port *skge, enum led_mode mode)
{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+
+ spin_lock_bh(&hw->phy_lock);
if (hw->chip_id == CHIP_ID_GENESIS) {
- skge_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_ON);
- skge_write8(hw, B0_LED, LED_STAT_ON);
+ switch (mode) {
+ case LED_MODE_OFF:
+ if (hw->phy_type == SK_PHY_BCOM)
+ xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, PHY_B_PEC_LED_OFF);
+ else {
+ skge_write32(hw, SK_REG(port, TX_LED_VAL), 0);
+ skge_write8(hw, SK_REG(port, TX_LED_CTRL), LED_T_OFF);
+ }
+ skge_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_OFF);
+ skge_write32(hw, SK_REG(port, RX_LED_VAL), 0);
+ skge_write8(hw, SK_REG(port, RX_LED_CTRL), LED_T_OFF);
+ break;
- skge_write8(hw, SK_REG(port, RX_LED_TST), LED_T_ON);
- skge_write32(hw, SK_REG(port, RX_LED_VAL), 100);
- skge_write8(hw, SK_REG(port, RX_LED_CTRL), LED_START);
+ case LED_MODE_ON:
+ skge_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_ON);
+ skge_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_LINKSYNC_ON);
- switch (hw->phy_type) {
- case SK_PHY_BCOM:
- xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL,
- PHY_B_PEC_LED_ON);
- break;
- case SK_PHY_LONE:
- xm_phy_write(hw, port, PHY_LONE_LED_CFG,
- 0x0800);
- break;
- default:
- skge_write8(hw, SK_REG(port, TX_LED_TST), LED_T_ON);
- skge_write32(hw, SK_REG(port, TX_LED_VAL), 100);
+ skge_write8(hw, SK_REG(port, RX_LED_CTRL), LED_START);
skge_write8(hw, SK_REG(port, TX_LED_CTRL), LED_START);
+
+ break;
+
+ case LED_MODE_TST:
+ skge_write8(hw, SK_REG(port, RX_LED_TST), LED_T_ON);
+ skge_write32(hw, SK_REG(port, RX_LED_VAL), 100);
+ skge_write8(hw, SK_REG(port, RX_LED_CTRL), LED_START);
+
+ if (hw->phy_type == SK_PHY_BCOM)
+ xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, PHY_B_PEC_LED_ON);
+ else {
+ skge_write8(hw, SK_REG(port, TX_LED_TST), LED_T_ON);
+ skge_write32(hw, SK_REG(port, TX_LED_VAL), 100);
+ skge_write8(hw, SK_REG(port, TX_LED_CTRL), LED_START);
+ }
+
}
} else {
- gm_phy_write(hw, port, PHY_MARV_LED_CTRL, 0);
- gm_phy_write(hw, port, PHY_MARV_LED_OVER,
- PHY_M_LED_MO_DUP(MO_LED_ON) |
- PHY_M_LED_MO_10(MO_LED_ON) |
- PHY_M_LED_MO_100(MO_LED_ON) |
- PHY_M_LED_MO_1000(MO_LED_ON) |
- PHY_M_LED_MO_RX(MO_LED_ON));
+ switch (mode) {
+ case LED_MODE_OFF:
+ gm_phy_write(hw, port, PHY_MARV_LED_CTRL, 0);
+ gm_phy_write(hw, port, PHY_MARV_LED_OVER,
+ PHY_M_LED_MO_DUP(MO_LED_OFF) |
+ PHY_M_LED_MO_10(MO_LED_OFF) |
+ PHY_M_LED_MO_100(MO_LED_OFF) |
+ PHY_M_LED_MO_1000(MO_LED_OFF) |
+ PHY_M_LED_MO_RX(MO_LED_OFF));
+ break;
+ case LED_MODE_ON:
+ gm_phy_write(hw, port, PHY_MARV_LED_CTRL,
+ PHY_M_LED_PULS_DUR(PULS_170MS) |
+ PHY_M_LED_BLINK_RT(BLINK_84MS) |
+ PHY_M_LEDC_TX_CTRL |
+ PHY_M_LEDC_DP_CTRL);
+
+ gm_phy_write(hw, port, PHY_MARV_LED_OVER,
+ PHY_M_LED_MO_RX(MO_LED_OFF) |
+ (skge->speed == SPEED_100 ?
+ PHY_M_LED_MO_100(MO_LED_ON) : 0));
+ break;
+ case LED_MODE_TST:
+ gm_phy_write(hw, port, PHY_MARV_LED_CTRL, 0);
+ gm_phy_write(hw, port, PHY_MARV_LED_OVER,
+ PHY_M_LED_MO_DUP(MO_LED_ON) |
+ PHY_M_LED_MO_10(MO_LED_ON) |
+ PHY_M_LED_MO_100(MO_LED_ON) |
+ PHY_M_LED_MO_1000(MO_LED_ON) |
+ PHY_M_LED_MO_RX(MO_LED_ON));
+ }
}
+ spin_unlock_bh(&hw->phy_lock);
}
-static void skge_led_off(struct skge_hw *hw, int port)
+/* blink LED's for finding board */
+static int skge_phys_id(struct net_device *dev, u32 data)
{
- if (hw->chip_id == CHIP_ID_GENESIS) {
- skge_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_OFF);
- skge_write8(hw, B0_LED, LED_STAT_OFF);
+ struct skge_port *skge = netdev_priv(dev);
+ unsigned long ms;
+ enum led_mode mode = LED_MODE_TST;
- skge_write32(hw, SK_REG(port, RX_LED_VAL), 0);
- skge_write8(hw, SK_REG(port, RX_LED_CTRL), LED_T_OFF);
+ if (!data || data > (u32)(MAX_SCHEDULE_TIMEOUT / HZ))
+ ms = jiffies_to_msecs(MAX_SCHEDULE_TIMEOUT / HZ) * 1000;
+ else
+ ms = data * 1000;
- switch (hw->phy_type) {
- case SK_PHY_BCOM:
- xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL,
- PHY_B_PEC_LED_OFF);
- break;
- case SK_PHY_LONE:
- xm_phy_write(hw, port, PHY_LONE_LED_CFG,
- PHY_L_LC_LEDT);
+ while (ms > 0) {
+ skge_led(skge, mode);
+ mode ^= LED_MODE_TST;
+
+ if (msleep_interruptible(BLINK_MS))
break;
- default:
- skge_write32(hw, SK_REG(port, TX_LED_VAL), 0);
- skge_write8(hw, SK_REG(port, TX_LED_CTRL), LED_T_OFF);
- }
- } else {
- gm_phy_write(hw, port, PHY_MARV_LED_CTRL, 0);
- gm_phy_write(hw, port, PHY_MARV_LED_OVER,
- PHY_M_LED_MO_DUP(MO_LED_OFF) |
- PHY_M_LED_MO_10(MO_LED_OFF) |
- PHY_M_LED_MO_100(MO_LED_OFF) |
- PHY_M_LED_MO_1000(MO_LED_OFF) |
- PHY_M_LED_MO_RX(MO_LED_OFF));
+ ms -= BLINK_MS;
}
+
+ /* back to regular LED state */
+ skge_led(skge, netif_running(dev) ? LED_MODE_ON : LED_MODE_OFF);
+
+ return 0;
}
-static void skge_blink_timer(unsigned long data)
+static int skge_get_eeprom_len(struct net_device *dev)
{
- struct skge_port *skge = (struct skge_port *) data;
- struct skge_hw *hw = skge->hw;
- unsigned long flags;
+ struct skge_port *skge = netdev_priv(dev);
+ u32 reg2;
- spin_lock_irqsave(&hw->phy_lock, flags);
- if (skge->blink_on)
- skge_led_on(hw, skge->port);
- else
- skge_led_off(hw, skge->port);
- spin_unlock_irqrestore(&hw->phy_lock, flags);
+ pci_read_config_dword(skge->hw->pdev, PCI_DEV_REG2, ®2);
+ return 1 << ( ((reg2 & PCI_VPD_ROM_SZ) >> 14) + 8);
+}
- skge->blink_on = !skge->blink_on;
- mod_timer(&skge->led_blink, jiffies + BLINK_HZ);
+static u32 skge_vpd_read(struct pci_dev *pdev, int cap, u16 offset)
+{
+ u32 val;
+
+ pci_write_config_word(pdev, cap + PCI_VPD_ADDR, offset);
+
+ do {
+ pci_read_config_word(pdev, cap + PCI_VPD_ADDR, &offset);
+ } while (!(offset & PCI_VPD_ADDR_F));
+
+ pci_read_config_dword(pdev, cap + PCI_VPD_DATA, &val);
+ return val;
}
-/* blink LED's for finding board */
-static int skge_phys_id(struct net_device *dev, u32 data)
+static void skge_vpd_write(struct pci_dev *pdev, int cap, u16 offset, u32 val)
+{
+ pci_write_config_dword(pdev, cap + PCI_VPD_DATA, val);
+ pci_write_config_word(pdev, cap + PCI_VPD_ADDR,
+ offset | PCI_VPD_ADDR_F);
+
+ do {
+ pci_read_config_word(pdev, cap + PCI_VPD_ADDR, &offset);
+ } while (offset & PCI_VPD_ADDR_F);
+}
+
+static int skge_get_eeprom(struct net_device *dev, struct ethtool_eeprom *eeprom,
+ u8 *data)
{
struct skge_port *skge = netdev_priv(dev);
+ struct pci_dev *pdev = skge->hw->pdev;
+ int cap = pci_find_capability(pdev, PCI_CAP_ID_VPD);
+ int length = eeprom->len;
+ u16 offset = eeprom->offset;
- if (!data || data > (u32)(MAX_SCHEDULE_TIMEOUT / HZ))
- data = (u32)(MAX_SCHEDULE_TIMEOUT / HZ);
+ if (!cap)
+ return -EINVAL;
+
+ eeprom->magic = SKGE_EEPROM_MAGIC;
+
+ while (length > 0) {
+ u32 val = skge_vpd_read(pdev, cap, offset);
+ int n = min_t(int, length, sizeof(val));
+
+ memcpy(data, &val, n);
+ length -= n;
+ data += n;
+ offset += n;
+ }
+ return 0;
+}
+
+static int skge_set_eeprom(struct net_device *dev, struct ethtool_eeprom *eeprom,
+ u8 *data)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct pci_dev *pdev = skge->hw->pdev;
+ int cap = pci_find_capability(pdev, PCI_CAP_ID_VPD);
+ int length = eeprom->len;
+ u16 offset = eeprom->offset;
+
+ if (!cap)
+ return -EINVAL;
+
+ if (eeprom->magic != SKGE_EEPROM_MAGIC)
+ return -EINVAL;
- /* start blinking */
- skge->blink_on = 1;
- mod_timer(&skge->led_blink, jiffies+1);
+ while (length > 0) {
+ u32 val;
+ int n = min_t(int, length, sizeof(val));
- msleep_interruptible(data * 1000);
- del_timer_sync(&skge->led_blink);
+ if (n < sizeof(val))
+ val = skge_vpd_read(pdev, cap, offset);
+ memcpy(&val, data, n);
- skge_led_off(skge->hw, skge->port);
+ skge_vpd_write(pdev, cap, offset, val);
+ length -= n;
+ data += n;
+ offset += n;
+ }
return 0;
}
-static struct ethtool_ops skge_ethtool_ops = {
+static const struct ethtool_ops skge_ethtool_ops = {
.get_settings = skge_get_settings,
.set_settings = skge_set_settings,
.get_drvinfo = skge_get_drvinfo,
.set_msglevel = skge_set_msglevel,
.nway_reset = skge_nway_reset,
.get_link = ethtool_op_get_link,
+ .get_eeprom_len = skge_get_eeprom_len,
+ .get_eeprom = skge_get_eeprom,
+ .set_eeprom = skge_set_eeprom,
.get_ringparam = skge_get_ring_param,
.set_ringparam = skge_set_ring_param,
.get_pauseparam = skge_get_pauseparam,
.set_pauseparam = skge_set_pauseparam,
.get_coalesce = skge_get_coalesce,
.set_coalesce = skge_set_coalesce,
- .get_sg = ethtool_op_get_sg,
.set_sg = skge_set_sg,
- .get_tx_csum = ethtool_op_get_tx_csum,
.set_tx_csum = skge_set_tx_csum,
.get_rx_csum = skge_get_rx_csum,
.set_rx_csum = skge_set_rx_csum,
.get_strings = skge_get_strings,
.phys_id = skge_phys_id,
- .get_stats_count = skge_get_stats_count,
+ .get_sset_count = skge_get_sset_count,
.get_ethtool_stats = skge_get_ethtool_stats,
};
* Allocate ring elements and chain them together
* One-to-one association of board descriptors with ring elements
*/
-static int skge_ring_alloc(struct skge_ring *ring, void *vaddr, u64 base)
+static int skge_ring_alloc(struct skge_ring *ring, void *vaddr, u32 base)
{
struct skge_tx_desc *d;
struct skge_element *e;
int i;
- ring->start = kmalloc(sizeof(*e)*ring->count, GFP_KERNEL);
+ ring->start = kcalloc(ring->count, sizeof(*e), GFP_KERNEL);
if (!ring->start)
return -ENOMEM;
return 0;
}
-/* Setup buffer for receiving */
-static inline int skge_rx_alloc(struct skge_port *skge,
- struct skge_element *e)
+/* Allocate and setup a new buffer for receiving */
+static void skge_rx_setup(struct skge_port *skge, struct skge_element *e,
+ struct sk_buff *skb, unsigned int bufsize)
{
- unsigned long bufsize = skge->netdev->mtu + ETH_HLEN; /* VLAN? */
struct skge_rx_desc *rd = e->desc;
- struct sk_buff *skb;
u64 map;
- skb = dev_alloc_skb(bufsize + NET_IP_ALIGN);
- if (unlikely(!skb)) {
- printk(KERN_DEBUG PFX "%s: out of memory for receive\n",
- skge->netdev->name);
- return -ENOMEM;
- }
-
- skb->dev = skge->netdev;
- skb_reserve(skb, NET_IP_ALIGN);
-
map = pci_map_single(skge->hw->pdev, skb->data, bufsize,
PCI_DMA_FROMDEVICE);
rd->control = BMU_OWN | BMU_STF | BMU_IRQ_EOF | BMU_TCP_CHECK | bufsize;
pci_unmap_addr_set(e, mapaddr, map);
pci_unmap_len_set(e, maplen, bufsize);
- return 0;
}
-/* Free all unused buffers in receive ring, assumes receiver stopped */
+/* Resume receiving using existing skb,
+ * Note: DMA address is not changed by chip.
+ * MTU not changed while receiver active.
+ */
+static inline void skge_rx_reuse(struct skge_element *e, unsigned int size)
+{
+ struct skge_rx_desc *rd = e->desc;
+
+ rd->csum2 = 0;
+ rd->csum2_start = ETH_HLEN;
+
+ wmb();
+
+ rd->control = BMU_OWN | BMU_STF | BMU_IRQ_EOF | BMU_TCP_CHECK | size;
+}
+
+
+/* Free all buffers in receive ring, assumes receiver stopped */
static void skge_rx_clean(struct skge_port *skge)
{
struct skge_hw *hw = skge->hw;
struct skge_ring *ring = &skge->rx_ring;
struct skge_element *e;
- for (e = ring->to_clean; e != ring->to_use; e = e->next) {
+ e = ring->start;
+ do {
struct skge_rx_desc *rd = e->desc;
rd->control = 0;
-
- pci_unmap_single(hw->pdev,
- pci_unmap_addr(e, mapaddr),
- pci_unmap_len(e, maplen),
- PCI_DMA_FROMDEVICE);
- dev_kfree_skb(e->skb);
- e->skb = NULL;
- }
- ring->to_clean = e;
+ if (e->skb) {
+ pci_unmap_single(hw->pdev,
+ pci_unmap_addr(e, mapaddr),
+ pci_unmap_len(e, maplen),
+ PCI_DMA_FROMDEVICE);
+ dev_kfree_skb(e->skb);
+ e->skb = NULL;
+ }
+ } while ((e = e->next) != ring->start);
}
+
/* Allocate buffers for receive ring
- * For receive: to_use is refill location
- * to_clean is next received frame.
- *
- * if (to_use == to_clean)
- * then ring all frames in ring need buffers
- * if (to_use->next == to_clean)
- * then ring all frames in ring have buffers
+ * For receive: to_clean is next received frame.
*/
-static int skge_rx_fill(struct skge_port *skge)
+static int skge_rx_fill(struct net_device *dev)
{
+ struct skge_port *skge = netdev_priv(dev);
struct skge_ring *ring = &skge->rx_ring;
struct skge_element *e;
- int ret = 0;
- for (e = ring->to_use; e->next != ring->to_clean; e = e->next) {
- if (skge_rx_alloc(skge, e)) {
- ret = 1;
- break;
- }
+ e = ring->start;
+ do {
+ struct sk_buff *skb;
- }
- ring->to_use = e;
+ skb = __netdev_alloc_skb(dev, skge->rx_buf_size + NET_IP_ALIGN,
+ GFP_KERNEL);
+ if (!skb)
+ return -ENOMEM;
- return ret;
+ skb_reserve(skb, NET_IP_ALIGN);
+ skge_rx_setup(skge, e, skb, skge->rx_buf_size);
+ } while ( (e = e->next) != ring->start);
+
+ ring->to_clean = ring->start;
+ return 0;
+}
+
+static const char *skge_pause(enum pause_status status)
+{
+ switch(status) {
+ case FLOW_STAT_NONE:
+ return "none";
+ case FLOW_STAT_REM_SEND:
+ return "rx only";
+ case FLOW_STAT_LOC_SEND:
+ return "tx_only";
+ case FLOW_STAT_SYMMETRIC: /* Both station may send PAUSE */
+ return "both";
+ default:
+ return "indeterminated";
+ }
}
+
static void skge_link_up(struct skge_port *skge)
{
+ skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG),
+ LED_BLK_OFF|LED_SYNC_OFF|LED_ON);
+
netif_carrier_on(skge->netdev);
- if (skge->tx_avail > MAX_SKB_FRAGS + 1)
- netif_wake_queue(skge->netdev);
+ netif_wake_queue(skge->netdev);
- if (netif_msg_link(skge))
+ if (netif_msg_link(skge)) {
printk(KERN_INFO PFX
"%s: Link is up at %d Mbps, %s duplex, flow control %s\n",
skge->netdev->name, skge->speed,
skge->duplex == DUPLEX_FULL ? "full" : "half",
- (skge->flow_control == FLOW_MODE_NONE) ? "none" :
- (skge->flow_control == FLOW_MODE_LOC_SEND) ? "tx only" :
- (skge->flow_control == FLOW_MODE_REM_SEND) ? "rx only" :
- (skge->flow_control == FLOW_MODE_SYMMETRIC) ? "tx and rx" :
- "unknown");
+ skge_pause(skge->flow_status));
+ }
}
static void skge_link_down(struct skge_port *skge)
{
+ skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG), LED_OFF);
netif_carrier_off(skge->netdev);
netif_stop_queue(skge->netdev);
printk(KERN_INFO PFX "%s: Link is down.\n", skge->netdev->name);
}
-static u16 xm_phy_read(struct skge_hw *hw, int port, u16 reg)
-{
- int i;
- u16 v;
- xm_write16(hw, port, XM_PHY_ADDR, reg | hw->phy_addr);
- v = xm_read16(hw, port, XM_PHY_DATA);
- if (hw->phy_type != SK_PHY_XMAC) {
- for (i = 0; i < PHY_RETRIES; i++) {
- udelay(1);
- if (xm_read16(hw, port, XM_MMU_CMD)
- & XM_MMU_PHY_RDY)
- goto ready;
- }
+static void xm_link_down(struct skge_hw *hw, int port)
+{
+ struct net_device *dev = hw->dev[port];
+ struct skge_port *skge = netdev_priv(dev);
- printk(KERN_WARNING PFX "%s: phy read timed out\n",
- hw->dev[port]->name);
- return 0;
- ready:
- v = xm_read16(hw, port, XM_PHY_DATA);
- }
+ xm_write16(hw, port, XM_IMSK, XM_IMSK_DISABLE);
- return v;
+ if (netif_carrier_ok(dev))
+ skge_link_down(skge);
}
-static void xm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val)
+static int __xm_phy_read(struct skge_hw *hw, int port, u16 reg, u16 *val)
{
int i;
xm_write16(hw, port, XM_PHY_ADDR, reg | hw->phy_addr);
- for (i = 0; i < PHY_RETRIES; i++) {
- if (!(xm_read16(hw, port, XM_MMU_CMD) & XM_MMU_PHY_BUSY))
- goto ready;
- cpu_relax();
- }
- printk(KERN_WARNING PFX "%s: phy write failed to come ready\n",
- hw->dev[port]->name);
+ *val = xm_read16(hw, port, XM_PHY_DATA);
+ if (hw->phy_type == SK_PHY_XMAC)
+ goto ready;
- ready:
- xm_write16(hw, port, XM_PHY_DATA, val);
for (i = 0; i < PHY_RETRIES; i++) {
+ if (xm_read16(hw, port, XM_MMU_CMD) & XM_MMU_PHY_RDY)
+ goto ready;
udelay(1);
- if (!(xm_read16(hw, port, XM_MMU_CMD) & XM_MMU_PHY_BUSY))
- return;
}
- printk(KERN_WARNING PFX "%s: phy write timed out\n",
- hw->dev[port]->name);
+
+ return -ETIMEDOUT;
+ ready:
+ *val = xm_read16(hw, port, XM_PHY_DATA);
+
+ return 0;
+}
+
+static u16 xm_phy_read(struct skge_hw *hw, int port, u16 reg)
+{
+ u16 v = 0;
+ if (__xm_phy_read(hw, port, reg, &v))
+ printk(KERN_WARNING PFX "%s: phy read timed out\n",
+ hw->dev[port]->name);
+ return v;
+}
+
+static int xm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val)
+{
+ int i;
+
+ xm_write16(hw, port, XM_PHY_ADDR, reg | hw->phy_addr);
+ for (i = 0; i < PHY_RETRIES; i++) {
+ if (!(xm_read16(hw, port, XM_MMU_CMD) & XM_MMU_PHY_BUSY))
+ goto ready;
+ udelay(1);
+ }
+ return -EIO;
+
+ ready:
+ xm_write16(hw, port, XM_PHY_DATA, val);
+ for (i = 0; i < PHY_RETRIES; i++) {
+ if (!(xm_read16(hw, port, XM_MMU_CMD) & XM_MMU_PHY_BUSY))
+ return 0;
+ udelay(1);
+ }
+ return -ETIMEDOUT;
}
static void genesis_init(struct skge_hw *hw)
static void genesis_reset(struct skge_hw *hw, int port)
{
- int i;
- u64 zero = 0;
+ const u8 zero[8] = { 0 };
+ u32 reg;
+
+ skge_write8(hw, SK_REG(port, GMAC_IRQ_MSK), 0);
/* reset the statistics module */
xm_write32(hw, port, XM_GP_PORT, XM_GP_RES_STAT);
- xm_write16(hw, port, XM_IMSK, 0xffff); /* disable XMAC IRQs */
+ xm_write16(hw, port, XM_IMSK, XM_IMSK_DISABLE);
xm_write32(hw, port, XM_MODE, 0); /* clear Mode Reg */
xm_write16(hw, port, XM_TX_CMD, 0); /* reset TX CMD Reg */
xm_write16(hw, port, XM_RX_CMD, 0); /* reset RX CMD Reg */
- /* disable all PHY IRQs */
- if (hw->phy_type == SK_PHY_BCOM)
+ /* disable Broadcom PHY IRQ */
+ if (hw->phy_type == SK_PHY_BCOM)
xm_write16(hw, port, PHY_BCOM_INT_MASK, 0xffff);
- xm_outhash(hw, port, XM_HSM, (u8 *) &zero);
- for (i = 0; i < 15; i++)
- xm_outaddr(hw, port, XM_EXM(i), (u8 *) &zero);
- xm_outhash(hw, port, XM_SRC_CHK, (u8 *) &zero);
+ xm_outhash(hw, port, XM_HSM, zero);
+
+ /* Flush TX and RX fifo */
+ reg = xm_read32(hw, port, XM_MODE);
+ xm_write32(hw, port, XM_MODE, reg | XM_MD_FTF);
+ xm_write32(hw, port, XM_MODE, reg | XM_MD_FRF);
}
-static void genesis_mac_init(struct skge_hw *hw, int port)
+/* Convert mode to MII values */
+static const u16 phy_pause_map[] = {
+ [FLOW_MODE_NONE] = 0,
+ [FLOW_MODE_LOC_SEND] = PHY_AN_PAUSE_ASYM,
+ [FLOW_MODE_SYMMETRIC] = PHY_AN_PAUSE_CAP,
+ [FLOW_MODE_SYM_OR_REM] = PHY_AN_PAUSE_CAP | PHY_AN_PAUSE_ASYM,
+};
+
+/* special defines for FIBER (88E1011S only) */
+static const u16 fiber_pause_map[] = {
+ [FLOW_MODE_NONE] = PHY_X_P_NO_PAUSE,
+ [FLOW_MODE_LOC_SEND] = PHY_X_P_ASYM_MD,
+ [FLOW_MODE_SYMMETRIC] = PHY_X_P_SYM_MD,
+ [FLOW_MODE_SYM_OR_REM] = PHY_X_P_BOTH_MD,
+};
+
+
+/* Check status of Broadcom phy link */
+static void bcom_check_link(struct skge_hw *hw, int port)
{
- struct skge_port *skge = netdev_priv(hw->dev[port]);
+ struct net_device *dev = hw->dev[port];
+ struct skge_port *skge = netdev_priv(dev);
+ u16 status;
+
+ /* read twice because of latch */
+ xm_phy_read(hw, port, PHY_BCOM_STAT);
+ status = xm_phy_read(hw, port, PHY_BCOM_STAT);
+
+ if ((status & PHY_ST_LSYNC) == 0) {
+ xm_link_down(hw, port);
+ return;
+ }
+
+ if (skge->autoneg == AUTONEG_ENABLE) {
+ u16 lpa, aux;
+
+ if (!(status & PHY_ST_AN_OVER))
+ return;
+
+ lpa = xm_phy_read(hw, port, PHY_XMAC_AUNE_LP);
+ if (lpa & PHY_B_AN_RF) {
+ printk(KERN_NOTICE PFX "%s: remote fault\n",
+ dev->name);
+ return;
+ }
+
+ aux = xm_phy_read(hw, port, PHY_BCOM_AUX_STAT);
+
+ /* Check Duplex mismatch */
+ switch (aux & PHY_B_AS_AN_RES_MSK) {
+ case PHY_B_RES_1000FD:
+ skge->duplex = DUPLEX_FULL;
+ break;
+ case PHY_B_RES_1000HD:
+ skge->duplex = DUPLEX_HALF;
+ break;
+ default:
+ printk(KERN_NOTICE PFX "%s: duplex mismatch\n",
+ dev->name);
+ return;
+ }
+
+ /* We are using IEEE 802.3z/D5.0 Table 37-4 */
+ switch (aux & PHY_B_AS_PAUSE_MSK) {
+ case PHY_B_AS_PAUSE_MSK:
+ skge->flow_status = FLOW_STAT_SYMMETRIC;
+ break;
+ case PHY_B_AS_PRR:
+ skge->flow_status = FLOW_STAT_REM_SEND;
+ break;
+ case PHY_B_AS_PRT:
+ skge->flow_status = FLOW_STAT_LOC_SEND;
+ break;
+ default:
+ skge->flow_status = FLOW_STAT_NONE;
+ }
+ skge->speed = SPEED_1000;
+ }
+
+ if (!netif_carrier_ok(dev))
+ genesis_link_up(skge);
+}
+
+/* Broadcom 5400 only supports giagabit! SysKonnect did not put an additional
+ * Phy on for 100 or 10Mbit operation
+ */
+static void bcom_phy_init(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
int i;
- u32 r;
- u16 id1;
- u16 ctrl1, ctrl2, ctrl3, ctrl4, ctrl5;
+ u16 id1, r, ext, ctl;
/* magic workaround patterns for Broadcom */
static const struct {
{ 0x17, 0x0013 }, { 0x15, 0x0A04 }, { 0x18, 0x0420 },
};
+ /* read Id from external PHY (all have the same address) */
+ id1 = xm_phy_read(hw, port, PHY_XMAC_ID1);
+
+ /* Optimize MDIO transfer by suppressing preamble. */
+ r = xm_read16(hw, port, XM_MMU_CMD);
+ r |= XM_MMU_NO_PRE;
+ xm_write16(hw, port, XM_MMU_CMD,r);
+
+ switch (id1) {
+ case PHY_BCOM_ID1_C0:
+ /*
+ * Workaround BCOM Errata for the C0 type.
+ * Write magic patterns to reserved registers.
+ */
+ for (i = 0; i < ARRAY_SIZE(C0hack); i++)
+ xm_phy_write(hw, port,
+ C0hack[i].reg, C0hack[i].val);
+
+ break;
+ case PHY_BCOM_ID1_A1:
+ /*
+ * Workaround BCOM Errata for the A1 type.
+ * Write magic patterns to reserved registers.
+ */
+ for (i = 0; i < ARRAY_SIZE(A1hack); i++)
+ xm_phy_write(hw, port,
+ A1hack[i].reg, A1hack[i].val);
+ break;
+ }
+
+ /*
+ * Workaround BCOM Errata (#10523) for all BCom PHYs.
+ * Disable Power Management after reset.
+ */
+ r = xm_phy_read(hw, port, PHY_BCOM_AUX_CTRL);
+ r |= PHY_B_AC_DIS_PM;
+ xm_phy_write(hw, port, PHY_BCOM_AUX_CTRL, r);
+
+ /* Dummy read */
+ xm_read16(hw, port, XM_ISRC);
+
+ ext = PHY_B_PEC_EN_LTR; /* enable tx led */
+ ctl = PHY_CT_SP1000; /* always 1000mbit */
+
+ if (skge->autoneg == AUTONEG_ENABLE) {
+ /*
+ * Workaround BCOM Errata #1 for the C5 type.
+ * 1000Base-T Link Acquisition Failure in Slave Mode
+ * Set Repeater/DTE bit 10 of the 1000Base-T Control Register
+ */
+ u16 adv = PHY_B_1000C_RD;
+ if (skge->advertising & ADVERTISED_1000baseT_Half)
+ adv |= PHY_B_1000C_AHD;
+ if (skge->advertising & ADVERTISED_1000baseT_Full)
+ adv |= PHY_B_1000C_AFD;
+ xm_phy_write(hw, port, PHY_BCOM_1000T_CTRL, adv);
+
+ ctl |= PHY_CT_ANE | PHY_CT_RE_CFG;
+ } else {
+ if (skge->duplex == DUPLEX_FULL)
+ ctl |= PHY_CT_DUP_MD;
+ /* Force to slave */
+ xm_phy_write(hw, port, PHY_BCOM_1000T_CTRL, PHY_B_1000C_MSE);
+ }
+
+ /* Set autonegotiation pause parameters */
+ xm_phy_write(hw, port, PHY_BCOM_AUNE_ADV,
+ phy_pause_map[skge->flow_control] | PHY_AN_CSMA);
+
+ /* Handle Jumbo frames */
+ if (hw->dev[port]->mtu > ETH_DATA_LEN) {
+ xm_phy_write(hw, port, PHY_BCOM_AUX_CTRL,
+ PHY_B_AC_TX_TST | PHY_B_AC_LONG_PACK);
+
+ ext |= PHY_B_PEC_HIGH_LA;
+
+ }
+
+ xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, ext);
+ xm_phy_write(hw, port, PHY_BCOM_CTRL, ctl);
+
+ /* Use link status change interrupt */
+ xm_phy_write(hw, port, PHY_BCOM_INT_MASK, PHY_B_DEF_MSK);
+}
+
+static void xm_phy_init(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ u16 ctrl = 0;
+
+ if (skge->autoneg == AUTONEG_ENABLE) {
+ if (skge->advertising & ADVERTISED_1000baseT_Half)
+ ctrl |= PHY_X_AN_HD;
+ if (skge->advertising & ADVERTISED_1000baseT_Full)
+ ctrl |= PHY_X_AN_FD;
+
+ ctrl |= fiber_pause_map[skge->flow_control];
+
+ xm_phy_write(hw, port, PHY_XMAC_AUNE_ADV, ctrl);
+
+ /* Restart Auto-negotiation */
+ ctrl = PHY_CT_ANE | PHY_CT_RE_CFG;
+ } else {
+ /* Set DuplexMode in Config register */
+ if (skge->duplex == DUPLEX_FULL)
+ ctrl |= PHY_CT_DUP_MD;
+ /*
+ * Do NOT enable Auto-negotiation here. This would hold
+ * the link down because no IDLEs are transmitted
+ */
+ }
+
+ xm_phy_write(hw, port, PHY_XMAC_CTRL, ctrl);
+
+ /* Poll PHY for status changes */
+ mod_timer(&skge->link_timer, jiffies + LINK_HZ);
+}
+
+static int xm_check_link(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ u16 status;
+
+ /* read twice because of latch */
+ xm_phy_read(hw, port, PHY_XMAC_STAT);
+ status = xm_phy_read(hw, port, PHY_XMAC_STAT);
+
+ if ((status & PHY_ST_LSYNC) == 0) {
+ xm_link_down(hw, port);
+ return 0;
+ }
+
+ if (skge->autoneg == AUTONEG_ENABLE) {
+ u16 lpa, res;
+
+ if (!(status & PHY_ST_AN_OVER))
+ return 0;
+
+ lpa = xm_phy_read(hw, port, PHY_XMAC_AUNE_LP);
+ if (lpa & PHY_B_AN_RF) {
+ printk(KERN_NOTICE PFX "%s: remote fault\n",
+ dev->name);
+ return 0;
+ }
+
+ res = xm_phy_read(hw, port, PHY_XMAC_RES_ABI);
+
+ /* Check Duplex mismatch */
+ switch (res & (PHY_X_RS_HD | PHY_X_RS_FD)) {
+ case PHY_X_RS_FD:
+ skge->duplex = DUPLEX_FULL;
+ break;
+ case PHY_X_RS_HD:
+ skge->duplex = DUPLEX_HALF;
+ break;
+ default:
+ printk(KERN_NOTICE PFX "%s: duplex mismatch\n",
+ dev->name);
+ return 0;
+ }
+
+ /* We are using IEEE 802.3z/D5.0 Table 37-4 */
+ if ((skge->flow_control == FLOW_MODE_SYMMETRIC ||
+ skge->flow_control == FLOW_MODE_SYM_OR_REM) &&
+ (lpa & PHY_X_P_SYM_MD))
+ skge->flow_status = FLOW_STAT_SYMMETRIC;
+ else if (skge->flow_control == FLOW_MODE_SYM_OR_REM &&
+ (lpa & PHY_X_RS_PAUSE) == PHY_X_P_ASYM_MD)
+ /* Enable PAUSE receive, disable PAUSE transmit */
+ skge->flow_status = FLOW_STAT_REM_SEND;
+ else if (skge->flow_control == FLOW_MODE_LOC_SEND &&
+ (lpa & PHY_X_RS_PAUSE) == PHY_X_P_BOTH_MD)
+ /* Disable PAUSE receive, enable PAUSE transmit */
+ skge->flow_status = FLOW_STAT_LOC_SEND;
+ else
+ skge->flow_status = FLOW_STAT_NONE;
+
+ skge->speed = SPEED_1000;
+ }
+
+ if (!netif_carrier_ok(dev))
+ genesis_link_up(skge);
+ return 1;
+}
+
+/* Poll to check for link coming up.
+ *
+ * Since internal PHY is wired to a level triggered pin, can't
+ * get an interrupt when carrier is detected, need to poll for
+ * link coming up.
+ */
+static void xm_link_timer(unsigned long arg)
+{
+ struct skge_port *skge = (struct skge_port *) arg;
+ struct net_device *dev = skge->netdev;
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ int i;
+ unsigned long flags;
+
+ if (!netif_running(dev))
+ return;
+
+ spin_lock_irqsave(&hw->phy_lock, flags);
+
+ /*
+ * Verify that the link by checking GPIO register three times.
+ * This pin has the signal from the link_sync pin connected to it.
+ */
+ for (i = 0; i < 3; i++) {
+ if (xm_read16(hw, port, XM_GP_PORT) & XM_GP_INP_ASS)
+ goto link_down;
+ }
+
+ /* Re-enable interrupt to detect link down */
+ if (xm_check_link(dev)) {
+ u16 msk = xm_read16(hw, port, XM_IMSK);
+ msk &= ~XM_IS_INP_ASS;
+ xm_write16(hw, port, XM_IMSK, msk);
+ xm_read16(hw, port, XM_ISRC);
+ } else {
+link_down:
+ mod_timer(&skge->link_timer,
+ round_jiffies(jiffies + LINK_HZ));
+ }
+ spin_unlock_irqrestore(&hw->phy_lock, flags);
+}
+
+static void genesis_mac_init(struct skge_hw *hw, int port)
+{
+ struct net_device *dev = hw->dev[port];
+ struct skge_port *skge = netdev_priv(dev);
+ int jumbo = hw->dev[port]->mtu > ETH_DATA_LEN;
+ int i;
+ u32 r;
+ const u8 zero[6] = { 0 };
- /* initialize Rx, Tx and Link LED */
- skge_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_ON);
- skge_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_LINKSYNC_ON);
+ for (i = 0; i < 10; i++) {
+ skge_write16(hw, SK_REG(port, TX_MFF_CTRL1),
+ MFF_SET_MAC_RST);
+ if (skge_read16(hw, SK_REG(port, TX_MFF_CTRL1)) & MFF_SET_MAC_RST)
+ goto reset_ok;
+ udelay(1);
+ }
- skge_write8(hw, SK_REG(port, RX_LED_CTRL), LED_START);
- skge_write8(hw, SK_REG(port, TX_LED_CTRL), LED_START);
+ printk(KERN_WARNING PFX "%s: genesis reset failed\n", dev->name);
+ reset_ok:
/* Unreset the XMAC. */
skge_write16(hw, SK_REG(port, TX_MFF_CTRL1), MFF_CLR_MAC_RST);
* namely for the 1000baseTX cards that use the XMAC's
* GMII mode.
*/
- spin_lock_bh(&hw->phy_lock);
if (hw->phy_type != SK_PHY_XMAC) {
- /* Take PHY out of reset. */
+ /* Take external Phy out of reset */
r = skge_read32(hw, B2_GP_IO);
if (port == 0)
r |= GP_DIR_0|GP_IO_0;
r |= GP_DIR_2|GP_IO_2;
skge_write32(hw, B2_GP_IO, r);
- skge_read32(hw, B2_GP_IO);
- /* Enable GMII mode on the XMAC. */
+ /* Enable GMII interface */
xm_write16(hw, port, XM_HW_CFG, XM_HW_GMII_MD);
+ }
- id1 = xm_phy_read(hw, port, PHY_XMAC_ID1);
-
- /* Optimize MDIO transfer by suppressing preamble. */
- xm_write16(hw, port, XM_MMU_CMD,
- xm_read16(hw, port, XM_MMU_CMD)
- | XM_MMU_NO_PRE);
-
- if (id1 == PHY_BCOM_ID1_C0) {
- /*
- * Workaround BCOM Errata for the C0 type.
- * Write magic patterns to reserved registers.
- */
- for (i = 0; i < ARRAY_SIZE(C0hack); i++)
- xm_phy_write(hw, port,
- C0hack[i].reg, C0hack[i].val);
-
- } else if (id1 == PHY_BCOM_ID1_A1) {
- /*
- * Workaround BCOM Errata for the A1 type.
- * Write magic patterns to reserved registers.
- */
- for (i = 0; i < ARRAY_SIZE(A1hack); i++)
- xm_phy_write(hw, port,
- A1hack[i].reg, A1hack[i].val);
- }
- /*
- * Workaround BCOM Errata (#10523) for all BCom PHYs.
- * Disable Power Management after reset.
- */
- r = xm_phy_read(hw, port, PHY_BCOM_AUX_CTRL);
- xm_phy_write(hw, port, PHY_BCOM_AUX_CTRL, r | PHY_B_AC_DIS_PM);
+ switch(hw->phy_type) {
+ case SK_PHY_XMAC:
+ xm_phy_init(skge);
+ break;
+ case SK_PHY_BCOM:
+ bcom_phy_init(skge);
+ bcom_check_link(hw, port);
}
- /* Dummy read */
- xm_read16(hw, port, XM_ISRC);
+ /* Set Station Address */
+ xm_outaddr(hw, port, XM_SA, dev->dev_addr);
+
+ /* We don't use match addresses so clear */
+ for (i = 1; i < 16; i++)
+ xm_outaddr(hw, port, XM_EXM(i), zero);
+
+ /* Clear MIB counters */
+ xm_write16(hw, port, XM_STAT_CMD,
+ XM_SC_CLR_RXC | XM_SC_CLR_TXC);
+ /* Clear two times according to Errata #3 */
+ xm_write16(hw, port, XM_STAT_CMD,
+ XM_SC_CLR_RXC | XM_SC_CLR_TXC);
- r = xm_read32(hw, port, XM_MODE);
- xm_write32(hw, port, XM_MODE, r|XM_MD_CSA);
+ /* configure Rx High Water Mark (XM_RX_HI_WM) */
+ xm_write16(hw, port, XM_RX_HI_WM, 1450);
/* We don't need the FCS appended to the packet. */
- r = xm_read16(hw, port, XM_RX_CMD);
- xm_write16(hw, port, XM_RX_CMD, r | XM_RX_STRIP_FCS);
+ r = XM_RX_LENERR_OK | XM_RX_STRIP_FCS;
+ if (jumbo)
+ r |= XM_RX_BIG_PK_OK;
+
+ if (skge->duplex == DUPLEX_HALF) {
+ /*
+ * If in manual half duplex mode the other side might be in
+ * full duplex mode, so ignore if a carrier extension is not seen
+ * on frames received
+ */
+ r |= XM_RX_DIS_CEXT;
+ }
+ xm_write16(hw, port, XM_RX_CMD, r);
/* We want short frames padded to 60 bytes. */
- r = xm_read16(hw, port, XM_TX_CMD);
- xm_write16(hw, port, XM_TX_CMD, r | XM_TX_AUTO_PAD);
+ xm_write16(hw, port, XM_TX_CMD, XM_TX_AUTO_PAD);
+
+ /* Increase threshold for jumbo frames on dual port */
+ if (hw->ports > 1 && jumbo)
+ xm_write16(hw, port, XM_TX_THR, 1020);
+ else
+ xm_write16(hw, port, XM_TX_THR, 512);
/*
* Enable the reception of all error frames. This is is
* that jumbo frames larger than 8192 bytes will be
* truncated. Disabling all bad frame filtering causes
* the RX FIFO to operate in streaming mode, in which
- * case the XMAC will start transfering frames out of the
+ * case the XMAC will start transferring frames out of the
* RX FIFO as soon as the FIFO threshold is reached.
*/
- r = xm_read32(hw, port, XM_MODE);
- xm_write32(hw, port, XM_MODE,
- XM_MD_RX_CRCE|XM_MD_RX_LONG|XM_MD_RX_RUNT|
- XM_MD_RX_ERR|XM_MD_RX_IRLE);
+ xm_write32(hw, port, XM_MODE, XM_DEF_MODE);
+
- xm_outaddr(hw, port, XM_SA, hw->dev[port]->dev_addr);
- xm_outaddr(hw, port, XM_EXM(0), hw->dev[port]->dev_addr);
+ /*
+ * Initialize the Receive Counter Event Mask (XM_RX_EV_MSK)
+ * - Enable all bits excepting 'Octets Rx OK Low CntOv'
+ * and 'Octets Rx OK Hi Cnt Ov'.
+ */
+ xm_write32(hw, port, XM_RX_EV_MSK, XMR_DEF_MSK);
/*
- * Bump up the transmit threshold. This helps hold off transmit
- * underruns when we're blasting traffic from both ports at once.
+ * Initialize the Transmit Counter Event Mask (XM_TX_EV_MSK)
+ * - Enable all bits excepting 'Octets Tx OK Low CntOv'
+ * and 'Octets Tx OK Hi Cnt Ov'.
*/
- xm_write16(hw, port, XM_TX_THR, 512);
+ xm_write32(hw, port, XM_TX_EV_MSK, XMT_DEF_MSK);
/* Configure MAC arbiter */
skge_write16(hw, B3_MA_TO_CTRL, MA_RST_CLR);
skge_write16(hw, SK_REG(port, TX_MFF_CTRL1), MFF_TX_CTRL_DEF);
skge_write8(hw, SK_REG(port, TX_MFF_CTRL2), MFF_ENA_OP_MD);
- if (hw->dev[port]->mtu > ETH_DATA_LEN) {
+ if (jumbo) {
/* Enable frame flushing if jumbo frames used */
skge_write16(hw, SK_REG(port,RX_MFF_CTRL1), MFF_ENA_FLUSH);
} else {
/* enable timeout timers if normal frames */
skge_write16(hw, B3_PA_CTRL,
- port == 0 ? PA_ENA_TO_TX1 : PA_ENA_TO_TX2);
+ (port == 0) ? PA_ENA_TO_TX1 : PA_ENA_TO_TX2);
}
-
-
- r = xm_read16(hw, port, XM_RX_CMD);
- if (hw->dev[port]->mtu > ETH_DATA_LEN)
- xm_write16(hw, port, XM_RX_CMD, r | XM_RX_BIG_PK_OK);
- else
- xm_write16(hw, port, XM_RX_CMD, r & ~(XM_RX_BIG_PK_OK));
-
- switch (hw->phy_type) {
- case SK_PHY_XMAC:
- if (skge->autoneg == AUTONEG_ENABLE) {
- ctrl1 = PHY_X_AN_FD | PHY_X_AN_HD;
-
- switch (skge->flow_control) {
- case FLOW_MODE_NONE:
- ctrl1 |= PHY_X_P_NO_PAUSE;
- break;
- case FLOW_MODE_LOC_SEND:
- ctrl1 |= PHY_X_P_ASYM_MD;
- break;
- case FLOW_MODE_SYMMETRIC:
- ctrl1 |= PHY_X_P_SYM_MD;
- break;
- case FLOW_MODE_REM_SEND:
- ctrl1 |= PHY_X_P_BOTH_MD;
- break;
- }
-
- xm_phy_write(hw, port, PHY_XMAC_AUNE_ADV, ctrl1);
- ctrl2 = PHY_CT_ANE | PHY_CT_RE_CFG;
- } else {
- ctrl2 = 0;
- if (skge->duplex == DUPLEX_FULL)
- ctrl2 |= PHY_CT_DUP_MD;
- }
-
- xm_phy_write(hw, port, PHY_XMAC_CTRL, ctrl2);
- break;
-
- case SK_PHY_BCOM:
- ctrl1 = PHY_CT_SP1000;
- ctrl2 = 0;
- ctrl3 = PHY_SEL_TYPE;
- ctrl4 = PHY_B_PEC_EN_LTR;
- ctrl5 = PHY_B_AC_TX_TST;
-
- if (skge->autoneg == AUTONEG_ENABLE) {
- /*
- * Workaround BCOM Errata #1 for the C5 type.
- * 1000Base-T Link Acquisition Failure in Slave Mode
- * Set Repeater/DTE bit 10 of the 1000Base-T Control Register
- */
- ctrl2 |= PHY_B_1000C_RD;
- if (skge->advertising & ADVERTISED_1000baseT_Half)
- ctrl2 |= PHY_B_1000C_AHD;
- if (skge->advertising & ADVERTISED_1000baseT_Full)
- ctrl2 |= PHY_B_1000C_AFD;
-
- /* Set Flow-control capabilities */
- switch (skge->flow_control) {
- case FLOW_MODE_NONE:
- ctrl3 |= PHY_B_P_NO_PAUSE;
- break;
- case FLOW_MODE_LOC_SEND:
- ctrl3 |= PHY_B_P_ASYM_MD;
- break;
- case FLOW_MODE_SYMMETRIC:
- ctrl3 |= PHY_B_P_SYM_MD;
- break;
- case FLOW_MODE_REM_SEND:
- ctrl3 |= PHY_B_P_BOTH_MD;
- break;
- }
-
- /* Restart Auto-negotiation */
- ctrl1 |= PHY_CT_ANE | PHY_CT_RE_CFG;
- } else {
- if (skge->duplex == DUPLEX_FULL)
- ctrl1 |= PHY_CT_DUP_MD;
-
- ctrl2 |= PHY_B_1000C_MSE; /* set it to Slave */
- }
-
- xm_phy_write(hw, port, PHY_BCOM_1000T_CTRL, ctrl2);
- xm_phy_write(hw, port, PHY_BCOM_AUNE_ADV, ctrl3);
-
- if (skge->netdev->mtu > ETH_DATA_LEN) {
- ctrl4 |= PHY_B_PEC_HIGH_LA;
- ctrl5 |= PHY_B_AC_LONG_PACK;
-
- xm_phy_write(hw, port,PHY_BCOM_AUX_CTRL, ctrl5);
- }
-
- xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, ctrl4);
- xm_phy_write(hw, port, PHY_BCOM_CTRL, ctrl1);
- break;
- }
- spin_unlock_bh(&hw->phy_lock);
-
- /* Clear MIB counters */
- xm_write16(hw, port, XM_STAT_CMD,
- XM_SC_CLR_RXC | XM_SC_CLR_TXC);
- /* Clear two times according to Errata #3 */
- xm_write16(hw, port, XM_STAT_CMD,
- XM_SC_CLR_RXC | XM_SC_CLR_TXC);
-
- /* Start polling for link status */
- mod_timer(&skge->link_check, jiffies + LINK_POLL_HZ);
}
static void genesis_stop(struct skge_port *skge)
{
struct skge_hw *hw = skge->hw;
int port = skge->port;
+ unsigned retries = 1000;
+ u16 cmd;
+
+ /* Disable Tx and Rx */
+ cmd = xm_read16(hw, port, XM_MMU_CMD);
+ cmd &= ~(XM_MMU_ENA_RX | XM_MMU_ENA_TX);
+ xm_write16(hw, port, XM_MMU_CMD, cmd);
+
+ genesis_reset(hw, port);
/* Clear Tx packet arbiter timeout IRQ */
skge_write16(hw, B3_PA_CTRL,
port == 0 ? PA_CLR_TO_TX1 : PA_CLR_TO_TX2);
- /*
- * If the transfer stucks at the MAC the STOP command will not
- * terminate if we don't flush the XMAC's transmit FIFO !
- */
- xm_write32(hw, port, XM_MODE,
- xm_read32(hw, port, XM_MODE)|XM_MD_FTF);
-
-
/* Reset the MAC */
- skge_write16(hw, SK_REG(port, TX_MFF_CTRL1), MFF_SET_MAC_RST);
+ skge_write16(hw, SK_REG(port, TX_MFF_CTRL1), MFF_CLR_MAC_RST);
+ do {
+ skge_write16(hw, SK_REG(port, TX_MFF_CTRL1), MFF_SET_MAC_RST);
+ if (!(skge_read16(hw, SK_REG(port, TX_MFF_CTRL1)) & MFF_SET_MAC_RST))
+ break;
+ } while (--retries > 0);
/* For external PHYs there must be special handling */
if (hw->phy_type != SK_PHY_XMAC) {
u32 reg = skge_read32(hw, B2_GP_IO);
-
if (port == 0) {
reg |= GP_DIR_0;
reg &= ~GP_IO_0;
static void genesis_mac_intr(struct skge_hw *hw, int port)
{
- struct skge_port *skge = netdev_priv(hw->dev[port]);
+ struct net_device *dev = hw->dev[port];
+ struct skge_port *skge = netdev_priv(dev);
u16 status = xm_read16(hw, port, XM_ISRC);
- pr_debug("genesis_intr status %x\n", status);
- if (hw->phy_type == SK_PHY_XMAC) {
- /* LInk down, start polling for state change */
- if (status & XM_IS_INP_ASS) {
- xm_write16(hw, port, XM_IMSK,
- xm_read16(hw, port, XM_IMSK) | XM_IS_INP_ASS);
- mod_timer(&skge->link_check, jiffies + LINK_POLL_HZ);
- }
- else if (status & XM_IS_AND)
- mod_timer(&skge->link_check, jiffies + LINK_POLL_HZ);
+ if (netif_msg_intr(skge))
+ printk(KERN_DEBUG PFX "%s: mac interrupt status 0x%x\n",
+ dev->name, status);
+
+ if (hw->phy_type == SK_PHY_XMAC && (status & XM_IS_INP_ASS)) {
+ xm_link_down(hw, port);
+ mod_timer(&skge->link_timer, jiffies + 1);
}
if (status & XM_IS_TXF_UR) {
xm_write32(hw, port, XM_MODE, XM_MD_FTF);
- ++skge->net_stats.tx_fifo_errors;
- }
- if (status & XM_IS_RXF_OV) {
- xm_write32(hw, port, XM_MODE, XM_MD_FRF);
- ++skge->net_stats.rx_fifo_errors;
+ ++dev->stats.tx_fifo_errors;
}
}
-static void gm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val)
-{
- int i;
-
- gma_write16(hw, port, GM_SMI_DATA, val);
- gma_write16(hw, port, GM_SMI_CTRL,
- GM_SMI_CT_PHY_AD(hw->phy_addr) | GM_SMI_CT_REG_AD(reg));
- for (i = 0; i < PHY_RETRIES; i++) {
- udelay(1);
-
- if (!(gma_read16(hw, port, GM_SMI_CTRL) & GM_SMI_CT_BUSY))
- break;
- }
-}
-
-static u16 gm_phy_read(struct skge_hw *hw, int port, u16 reg)
-{
- int i;
-
- gma_write16(hw, port, GM_SMI_CTRL,
- GM_SMI_CT_PHY_AD(hw->phy_addr)
- | GM_SMI_CT_REG_AD(reg) | GM_SMI_CT_OP_RD);
-
- for (i = 0; i < PHY_RETRIES; i++) {
- udelay(1);
- if (gma_read16(hw, port, GM_SMI_CTRL) & GM_SMI_CT_RD_VAL)
- goto ready;
- }
-
- printk(KERN_WARNING PFX "%s: phy read timeout\n",
- hw->dev[port]->name);
- return 0;
- ready:
- return gma_read16(hw, port, GM_SMI_DATA);
-}
-
-static void genesis_link_down(struct skge_port *skge)
-{
- struct skge_hw *hw = skge->hw;
- int port = skge->port;
-
- pr_debug("genesis_link_down\n");
-
- xm_write16(hw, port, XM_MMU_CMD,
- xm_read16(hw, port, XM_MMU_CMD)
- & ~(XM_MMU_ENA_RX | XM_MMU_ENA_TX));
-
- /* dummy read to ensure writing */
- (void) xm_read16(hw, port, XM_MMU_CMD);
-
- skge_link_down(skge);
-}
-
static void genesis_link_up(struct skge_port *skge)
{
struct skge_hw *hw = skge->hw;
int port = skge->port;
- u16 cmd;
- u32 mode, msk;
+ u16 cmd, msk;
+ u32 mode;
- pr_debug("genesis_link_up\n");
cmd = xm_read16(hw, port, XM_MMU_CMD);
/*
* enabling pause frame reception is required for 1000BT
* because the XMAC is not reset if the link is going down
*/
- if (skge->flow_control == FLOW_MODE_NONE ||
- skge->flow_control == FLOW_MODE_LOC_SEND)
+ if (skge->flow_status == FLOW_STAT_NONE ||
+ skge->flow_status == FLOW_STAT_LOC_SEND)
+ /* Disable Pause Frame Reception */
cmd |= XM_MMU_IGN_PF;
else
/* Enable Pause Frame Reception */
xm_write16(hw, port, XM_MMU_CMD, cmd);
mode = xm_read32(hw, port, XM_MODE);
- if (skge->flow_control == FLOW_MODE_SYMMETRIC ||
- skge->flow_control == FLOW_MODE_LOC_SEND) {
+ if (skge->flow_status== FLOW_STAT_SYMMETRIC ||
+ skge->flow_status == FLOW_STAT_LOC_SEND) {
/*
* Configure Pause Frame Generation
* Use internal and external Pause Frame Generation.
xm_write32(hw, port, XM_MODE, mode);
- msk = XM_DEF_MSK;
- if (hw->phy_type != SK_PHY_XMAC)
- msk |= XM_IS_INP_ASS; /* disable GP0 interrupt bit */
-
+ /* Turn on detection of Tx underrun */
+ msk = xm_read16(hw, port, XM_IMSK);
+ msk &= ~XM_IS_TXF_UR;
xm_write16(hw, port, XM_IMSK, msk);
+
xm_read16(hw, port, XM_ISRC);
/* get MMU Command Reg. */
if (hw->phy_type != SK_PHY_XMAC && skge->duplex == DUPLEX_FULL)
cmd |= XM_MMU_GMII_FD;
+ /*
+ * Workaround BCOM Errata (#10523) for all BCom Phys
+ * Enable Power Management after link up
+ */
if (hw->phy_type == SK_PHY_BCOM) {
- /*
- * Workaround BCOM Errata (#10523) for all BCom Phys
- * Enable Power Management after link up
- */
xm_phy_write(hw, port, PHY_BCOM_AUX_CTRL,
- xm_phy_read(hw, port, PHY_BCOM_AUX_CTRL)
- & ~PHY_B_AC_DIS_PM);
- xm_phy_write(hw, port, PHY_BCOM_INT_MASK,
- PHY_B_DEF_MSK);
+ xm_phy_read(hw, port, PHY_BCOM_AUX_CTRL)
+ & ~PHY_B_AC_DIS_PM);
+ xm_phy_write(hw, port, PHY_BCOM_INT_MASK, PHY_B_DEF_MSK);
}
/* enable Rx/Tx */
}
-static void genesis_bcom_intr(struct skge_port *skge)
+static inline void bcom_phy_intr(struct skge_port *skge)
{
struct skge_hw *hw = skge->hw;
int port = skge->port;
- u16 stat = xm_phy_read(hw, port, PHY_BCOM_INT_STAT);
+ u16 isrc;
- pr_debug("genesis_bcom intr stat=%x\n", stat);
+ isrc = xm_phy_read(hw, port, PHY_BCOM_INT_STAT);
+ if (netif_msg_intr(skge))
+ printk(KERN_DEBUG PFX "%s: phy interrupt status 0x%x\n",
+ skge->netdev->name, isrc);
+
+ if (isrc & PHY_B_IS_PSE)
+ printk(KERN_ERR PFX "%s: uncorrectable pair swap error\n",
+ hw->dev[port]->name);
/* Workaround BCom Errata:
* enable and disable loopback mode if "NO HCD" occurs.
*/
- if (stat & PHY_B_IS_NO_HDCL) {
+ if (isrc & PHY_B_IS_NO_HDCL) {
u16 ctrl = xm_phy_read(hw, port, PHY_BCOM_CTRL);
xm_phy_write(hw, port, PHY_BCOM_CTRL,
ctrl | PHY_CT_LOOP);
ctrl & ~PHY_CT_LOOP);
}
- stat = xm_phy_read(hw, port, PHY_BCOM_STAT);
- if (stat & (PHY_B_IS_AN_PR | PHY_B_IS_LST_CHANGE)) {
- u16 aux = xm_phy_read(hw, port, PHY_BCOM_AUX_STAT);
- if ( !(aux & PHY_B_AS_LS) && netif_carrier_ok(skge->netdev))
- genesis_link_down(skge);
-
- else if (stat & PHY_B_IS_LST_CHANGE) {
- if (aux & PHY_B_AS_AN_C) {
- switch (aux & PHY_B_AS_AN_RES_MSK) {
- case PHY_B_RES_1000FD:
- skge->duplex = DUPLEX_FULL;
- break;
- case PHY_B_RES_1000HD:
- skge->duplex = DUPLEX_HALF;
- break;
- }
-
- switch (aux & PHY_B_AS_PAUSE_MSK) {
- case PHY_B_AS_PAUSE_MSK:
- skge->flow_control = FLOW_MODE_SYMMETRIC;
- break;
- case PHY_B_AS_PRR:
- skge->flow_control = FLOW_MODE_REM_SEND;
- break;
- case PHY_B_AS_PRT:
- skge->flow_control = FLOW_MODE_LOC_SEND;
- break;
- default:
- skge->flow_control = FLOW_MODE_NONE;
- }
- skge->speed = SPEED_1000;
- }
- genesis_link_up(skge);
- }
- else
- mod_timer(&skge->link_check, jiffies + LINK_POLL_HZ);
+ if (isrc & (PHY_B_IS_AN_PR | PHY_B_IS_LST_CHANGE))
+ bcom_check_link(hw, port);
+
+}
+
+static int gm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val)
+{
+ int i;
+
+ gma_write16(hw, port, GM_SMI_DATA, val);
+ gma_write16(hw, port, GM_SMI_CTRL,
+ GM_SMI_CT_PHY_AD(hw->phy_addr) | GM_SMI_CT_REG_AD(reg));
+ for (i = 0; i < PHY_RETRIES; i++) {
+ udelay(1);
+
+ if (!(gma_read16(hw, port, GM_SMI_CTRL) & GM_SMI_CT_BUSY))
+ return 0;
+ }
+
+ printk(KERN_WARNING PFX "%s: phy write timeout\n",
+ hw->dev[port]->name);
+ return -EIO;
+}
+
+static int __gm_phy_read(struct skge_hw *hw, int port, u16 reg, u16 *val)
+{
+ int i;
+
+ gma_write16(hw, port, GM_SMI_CTRL,
+ GM_SMI_CT_PHY_AD(hw->phy_addr)
+ | GM_SMI_CT_REG_AD(reg) | GM_SMI_CT_OP_RD);
+
+ for (i = 0; i < PHY_RETRIES; i++) {
+ udelay(1);
+ if (gma_read16(hw, port, GM_SMI_CTRL) & GM_SMI_CT_RD_VAL)
+ goto ready;
}
+
+ return -ETIMEDOUT;
+ ready:
+ *val = gma_read16(hw, port, GM_SMI_DATA);
+ return 0;
}
-/* Perodic poll of phy status to check for link transistion */
-static void skge_link_timer(unsigned long __arg)
+static u16 gm_phy_read(struct skge_hw *hw, int port, u16 reg)
{
- struct skge_port *skge = (struct skge_port *) __arg;
- struct skge_hw *hw = skge->hw;
- int port = skge->port;
-
- if (hw->chip_id != CHIP_ID_GENESIS || !netif_running(skge->netdev))
- return;
-
- spin_lock_bh(&hw->phy_lock);
- if (hw->phy_type == SK_PHY_BCOM)
- genesis_bcom_intr(skge);
- else {
- int i;
- for (i = 0; i < 3; i++)
- if (xm_read16(hw, port, XM_ISRC) & XM_IS_INP_ASS)
- break;
-
- if (i == 3)
- mod_timer(&skge->link_check, jiffies + LINK_POLL_HZ);
- else
- genesis_link_up(skge);
- }
- spin_unlock_bh(&hw->phy_lock);
+ u16 v = 0;
+ if (__gm_phy_read(hw, port, reg, &v))
+ printk(KERN_WARNING PFX "%s: phy read timeout\n",
+ hw->dev[port]->name);
+ return v;
}
-/* Marvell Phy Initailization */
+/* Marvell Phy Initialization */
static void yukon_init(struct skge_hw *hw, int port)
{
struct skge_port *skge = netdev_priv(hw->dev[port]);
u16 ctrl, ct1000, adv;
- u16 ledctrl, ledover;
- pr_debug("yukon_init\n");
if (skge->autoneg == AUTONEG_ENABLE) {
u16 ectrl = gm_phy_read(hw, port, PHY_MARV_EXT_CTRL);
PHY_M_EC_MAC_S_MSK);
ectrl |= PHY_M_EC_MAC_S(MAC_TX_CLK_25_MHZ);
- /* on PHY 88E1111 there is a change for downshift control */
- if (hw->chip_id == CHIP_ID_YUKON_EC)
- ectrl |= PHY_M_EC_M_DSC_2(0) | PHY_M_EC_DOWN_S_ENA;
- else
- ectrl |= PHY_M_EC_M_DSC(0) | PHY_M_EC_S_DSC(1);
+ ectrl |= PHY_M_EC_M_DSC(0) | PHY_M_EC_S_DSC(1);
gm_phy_write(hw, port, PHY_MARV_EXT_CTRL, ectrl);
}
ctrl = 0;
ct1000 = 0;
- adv = PHY_SEL_TYPE;
+ adv = PHY_AN_CSMA;
if (skge->autoneg == AUTONEG_ENABLE) {
- if (iscopper(hw)) {
+ if (hw->copper) {
if (skge->advertising & ADVERTISED_1000baseT_Full)
ct1000 |= PHY_M_1000C_AFD;
if (skge->advertising & ADVERTISED_1000baseT_Half)
adv |= PHY_M_AN_10_HD;
/* Set Flow-control capabilities */
- switch (skge->flow_control) {
- case FLOW_MODE_NONE:
- adv |= PHY_B_P_NO_PAUSE;
- break;
- case FLOW_MODE_LOC_SEND:
- adv |= PHY_B_P_ASYM_MD;
- break;
- case FLOW_MODE_SYMMETRIC:
- adv |= PHY_B_P_SYM_MD;
- break;
- case FLOW_MODE_REM_SEND:
- adv |= PHY_B_P_BOTH_MD;
- break;
- }
- } else { /* special defines for FIBER (88E1011S only) */
- adv |= PHY_M_AN_1000X_AHD | PHY_M_AN_1000X_AFD;
+ adv |= phy_pause_map[skge->flow_control];
+ } else {
+ if (skge->advertising & ADVERTISED_1000baseT_Full)
+ adv |= PHY_M_AN_1000X_AFD;
+ if (skge->advertising & ADVERTISED_1000baseT_Half)
+ adv |= PHY_M_AN_1000X_AHD;
- /* Set Flow-control capabilities */
- switch (skge->flow_control) {
- case FLOW_MODE_NONE:
- adv |= PHY_M_P_NO_PAUSE_X;
- break;
- case FLOW_MODE_LOC_SEND:
- adv |= PHY_M_P_ASYM_MD_X;
- break;
- case FLOW_MODE_SYMMETRIC:
- adv |= PHY_M_P_SYM_MD_X;
- break;
- case FLOW_MODE_REM_SEND:
- adv |= PHY_M_P_BOTH_MD_X;
- break;
- }
+ adv |= fiber_pause_map[skge->flow_control];
}
+
/* Restart Auto-negotiation */
ctrl |= PHY_CT_ANE | PHY_CT_RE_CFG;
} else {
ctrl |= PHY_CT_RESET;
}
- if (hw->chip_id != CHIP_ID_YUKON_FE)
- gm_phy_write(hw, port, PHY_MARV_1000T_CTRL, ct1000);
+ gm_phy_write(hw, port, PHY_MARV_1000T_CTRL, ct1000);
gm_phy_write(hw, port, PHY_MARV_AUNE_ADV, adv);
gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
- /* Setup Phy LED's */
- ledctrl = PHY_M_LED_PULS_DUR(PULS_170MS);
- ledover = 0;
-
- if (hw->chip_id == CHIP_ID_YUKON_FE) {
- /* on 88E3082 these bits are at 11..9 (shifted left) */
- ledctrl |= PHY_M_LED_BLINK_RT(BLINK_84MS) << 1;
-
- gm_phy_write(hw, port, PHY_MARV_FE_LED_PAR,
- ((gm_phy_read(hw, port, PHY_MARV_FE_LED_PAR)
-
- & ~PHY_M_FELP_LED1_MSK)
- | PHY_M_FELP_LED1_CTRL(LED_PAR_CTRL_ACT_BL)));
- } else {
- /* set Tx LED (LED_TX) to blink mode on Rx OR Tx activity */
- ledctrl |= PHY_M_LED_BLINK_RT(BLINK_84MS) | PHY_M_LEDC_TX_CTRL;
-
- /* turn off the Rx LED (LED_RX) */
- ledover |= PHY_M_LED_MO_RX(MO_LED_OFF);
- }
-
- /* disable blink mode (LED_DUPLEX) on collisions */
- ctrl |= PHY_M_LEDC_DP_CTRL;
- gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
-
- if (skge->autoneg == AUTONEG_DISABLE || skge->speed == SPEED_100) {
- /* turn on 100 Mbps LED (LED_LINK100) */
- ledover |= PHY_M_LED_MO_100(MO_LED_ON);
- }
-
- if (ledover)
- gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover);
-
/* Enable phy interrupt on autonegotiation complete (or link up) */
if (skge->autoneg == AUTONEG_ENABLE)
- gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_AN_COMPL);
+ gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_AN_MSK);
else
- gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK);
+ gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_DEF_MSK);
}
static void yukon_reset(struct skge_hw *hw, int port)
| GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA);
}
+/* Apparently, early versions of Yukon-Lite had wrong chip_id? */
+static int is_yukon_lite_a0(struct skge_hw *hw)
+{
+ u32 reg;
+ int ret;
+
+ if (hw->chip_id != CHIP_ID_YUKON)
+ return 0;
+
+ reg = skge_read32(hw, B2_FAR);
+ skge_write8(hw, B2_FAR + 3, 0xff);
+ ret = (skge_read8(hw, B2_FAR + 3) != 0);
+ skge_write32(hw, B2_FAR, reg);
+ return ret;
+}
+
static void yukon_mac_init(struct skge_hw *hw, int port)
{
struct skge_port *skge = netdev_priv(hw->dev[port]);
/* WA code for COMA mode -- set PHY reset */
if (hw->chip_id == CHIP_ID_YUKON_LITE &&
- hw->chip_rev == CHIP_REV_YU_LITE_A3)
- skge_write32(hw, B2_GP_IO,
- (skge_read32(hw, B2_GP_IO) | GP_DIR_9 | GP_IO_9));
+ hw->chip_rev >= CHIP_REV_YU_LITE_A3) {
+ reg = skge_read32(hw, B2_GP_IO);
+ reg |= GP_DIR_9 | GP_IO_9;
+ skge_write32(hw, B2_GP_IO, reg);
+ }
/* hard reset */
skge_write32(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET);
/* WA code for COMA mode -- clear PHY reset */
if (hw->chip_id == CHIP_ID_YUKON_LITE &&
- hw->chip_rev == CHIP_REV_YU_LITE_A3)
- skge_write32(hw, B2_GP_IO,
- (skge_read32(hw, B2_GP_IO) | GP_DIR_9)
- & ~GP_IO_9);
+ hw->chip_rev >= CHIP_REV_YU_LITE_A3) {
+ reg = skge_read32(hw, B2_GP_IO);
+ reg |= GP_DIR_9;
+ reg &= ~GP_IO_9;
+ skge_write32(hw, B2_GP_IO, reg);
+ }
/* Set hardware config mode */
reg = GPC_INT_POL_HI | GPC_DIS_FC | GPC_DIS_SLEEP |
GPC_ENA_XC | GPC_ANEG_ADV_ALL_M | GPC_ENA_PAUSE;
- reg |= iscopper(hw) ? GPC_HWCFG_GMII_COP : GPC_HWCFG_GMII_FIB;
+ reg |= hw->copper ? GPC_HWCFG_GMII_COP : GPC_HWCFG_GMII_FIB;
/* Clear GMC reset */
skge_write32(hw, SK_REG(port, GPHY_CTRL), reg | GPC_RST_SET);
skge_write32(hw, SK_REG(port, GPHY_CTRL), reg | GPC_RST_CLR);
skge_write32(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON | GMC_RST_CLR);
+
if (skge->autoneg == AUTONEG_DISABLE) {
reg = GM_GPCR_AU_ALL_DIS;
gma_write16(hw, port, GM_GP_CTRL,
switch (skge->speed) {
case SPEED_1000:
+ reg &= ~GM_GPCR_SPEED_100;
reg |= GM_GPCR_SPEED_1000;
- /* fallthru */
+ break;
case SPEED_100:
+ reg &= ~GM_GPCR_SPEED_1000;
reg |= GM_GPCR_SPEED_100;
+ break;
+ case SPEED_10:
+ reg &= ~(GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100);
+ break;
}
if (skge->duplex == DUPLEX_FULL)
reg |= GM_GPCR_DUP_FULL;
} else
reg = GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100 | GM_GPCR_DUP_FULL;
+
switch (skge->flow_control) {
case FLOW_MODE_NONE:
skge_write32(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
case FLOW_MODE_LOC_SEND:
/* disable Rx flow-control */
reg |= GM_GPCR_FC_RX_DIS | GM_GPCR_AU_FCT_DIS;
+ break;
+ case FLOW_MODE_SYMMETRIC:
+ case FLOW_MODE_SYM_OR_REM:
+ /* enable Tx & Rx flow-control */
+ break;
}
gma_write16(hw, port, GM_GP_CTRL, reg);
- skge_read16(hw, GMAC_IRQ_SRC);
+ skge_read16(hw, SK_REG(port, GMAC_IRQ_SRC));
- spin_lock_bh(&hw->phy_lock);
yukon_init(hw, port);
- spin_unlock_bh(&hw->phy_lock);
/* MIB clear */
reg = gma_read16(hw, port, GM_PHY_ADDR);
TX_JAM_IPG_VAL(TX_JAM_IPG_DEF) |
TX_IPG_JAM_DATA(TX_IPG_JAM_DEF));
- /* serial mode register */
- reg = GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF);
- if (hw->dev[port]->mtu > 1500)
+ /* configure the Serial Mode Register */
+ reg = DATA_BLIND_VAL(DATA_BLIND_DEF)
+ | GM_SMOD_VLAN_ENA
+ | IPG_DATA_VAL(IPG_DATA_DEF);
+
+ if (hw->dev[port]->mtu > ETH_DATA_LEN)
reg |= GM_SMOD_JUMBO_ENA;
gma_write16(hw, port, GM_SERIAL_MODE, reg);
/* Configure Rx MAC FIFO */
skge_write16(hw, SK_REG(port, RX_GMF_FL_MSK), RX_FF_FL_DEF_MSK);
reg = GMF_OPER_ON | GMF_RX_F_FL_ON;
- if (hw->chip_id == CHIP_ID_YUKON_LITE &&
- hw->chip_rev == CHIP_REV_YU_LITE_A3)
+
+ /* disable Rx GMAC FIFO Flush for YUKON-Lite Rev. A0 only */
+ if (is_yukon_lite_a0(hw))
reg &= ~GMF_RX_F_FL_ON;
+
skge_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_CLR);
skge_write16(hw, SK_REG(port, RX_GMF_CTRL_T), reg);
- skge_write16(hw, SK_REG(port, RX_GMF_FL_THR), RX_GMF_FL_THR_DEF);
+ /*
+ * because Pause Packet Truncation in GMAC is not working
+ * we have to increase the Flush Threshold to 64 bytes
+ * in order to flush pause packets in Rx FIFO on Yukon-1
+ */
+ skge_write16(hw, SK_REG(port, RX_GMF_FL_THR), RX_GMF_FL_THR_DEF+1);
/* Configure Tx MAC FIFO */
skge_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_CLR);
skge_write16(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_OPER_ON);
}
+/* Go into power down mode */
+static void yukon_suspend(struct skge_hw *hw, int port)
+{
+ u16 ctrl;
+
+ ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
+ ctrl |= PHY_M_PC_POL_R_DIS;
+ gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
+
+ ctrl = gm_phy_read(hw, port, PHY_MARV_CTRL);
+ ctrl |= PHY_CT_RESET;
+ gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
+
+ /* switch IEEE compatible power down mode on */
+ ctrl = gm_phy_read(hw, port, PHY_MARV_CTRL);
+ ctrl |= PHY_CT_PDOWN;
+ gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
+}
+
static void yukon_stop(struct skge_port *skge)
{
struct skge_hw *hw = skge->hw;
int port = skge->port;
- if (hw->chip_id == CHIP_ID_YUKON_LITE &&
- hw->chip_rev == CHIP_REV_YU_LITE_A3) {
- skge_write32(hw, B2_GP_IO,
- skge_read32(hw, B2_GP_IO) | GP_DIR_9 | GP_IO_9);
- }
+ skge_write8(hw, SK_REG(port, GMAC_IRQ_MSK), 0);
+ yukon_reset(hw, port);
gma_write16(hw, port, GM_GP_CTRL,
gma_read16(hw, port, GM_GP_CTRL)
- & ~(GM_GPCR_RX_ENA|GM_GPCR_RX_ENA));
+ & ~(GM_GPCR_TX_ENA|GM_GPCR_RX_ENA));
gma_read16(hw, port, GM_GP_CTRL);
+ yukon_suspend(hw, port);
+
/* set GPHY Control reset */
- gma_write32(hw, port, GPHY_CTRL, GPC_RST_SET);
- gma_write32(hw, port, GMAC_CTRL, GMC_RST_SET);
+ skge_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET);
+ skge_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_SET);
}
static void yukon_get_stats(struct skge_port *skge, u64 *data)
static void yukon_mac_intr(struct skge_hw *hw, int port)
{
- struct skge_port *skge = netdev_priv(hw->dev[port]);
+ struct net_device *dev = hw->dev[port];
+ struct skge_port *skge = netdev_priv(dev);
u8 status = skge_read8(hw, SK_REG(port, GMAC_IRQ_SRC));
- pr_debug("yukon_intr status %x\n", status);
+ if (netif_msg_intr(skge))
+ printk(KERN_DEBUG PFX "%s: mac interrupt status 0x%x\n",
+ dev->name, status);
+
if (status & GM_IS_RX_FF_OR) {
- ++skge->net_stats.rx_fifo_errors;
- gma_write8(hw, port, RX_GMF_CTRL_T, GMF_CLI_RX_FO);
+ ++dev->stats.rx_fifo_errors;
+ skge_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_CLI_RX_FO);
}
+
if (status & GM_IS_TX_FF_UR) {
- ++skge->net_stats.tx_fifo_errors;
- gma_write8(hw, port, TX_GMF_CTRL_T, GMF_CLI_TX_FU);
+ ++dev->stats.tx_fifo_errors;
+ skge_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_CLI_TX_FU);
}
}
static u16 yukon_speed(const struct skge_hw *hw, u16 aux)
{
- if (hw->chip_id == CHIP_ID_YUKON_FE)
- return (aux & PHY_M_PS_SPEED_100) ? SPEED_100 : SPEED_10;
-
switch (aux & PHY_M_PS_SPEED_MSK) {
case PHY_M_PS_SPEED_1000:
return SPEED_1000;
int port = skge->port;
u16 reg;
- pr_debug("yukon_link_up\n");
-
/* Enable Transmit FIFO Underrun */
- skge_write8(hw, GMAC_IRQ_MSK, GMAC_DEF_MSK);
+ skge_write8(hw, SK_REG(port, GMAC_IRQ_MSK), GMAC_DEF_MSK);
reg = gma_read16(hw, port, GM_GP_CTRL);
if (skge->duplex == DUPLEX_FULL || skge->autoneg == AUTONEG_ENABLE)
reg |= GM_GPCR_RX_ENA | GM_GPCR_TX_ENA;
gma_write16(hw, port, GM_GP_CTRL, reg);
- gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK);
+ gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_DEF_MSK);
skge_link_up(skge);
}
{
struct skge_hw *hw = skge->hw;
int port = skge->port;
+ u16 ctrl;
- pr_debug("yukon_link_down\n");
- gm_phy_write(hw, port, PHY_MARV_INT_MASK, 0);
- gm_phy_write(hw, port, GM_GP_CTRL,
- gm_phy_read(hw, port, GM_GP_CTRL)
- & ~(GM_GPCR_RX_ENA | GM_GPCR_TX_ENA));
+ ctrl = gma_read16(hw, port, GM_GP_CTRL);
+ ctrl &= ~(GM_GPCR_RX_ENA | GM_GPCR_TX_ENA);
+ gma_write16(hw, port, GM_GP_CTRL, ctrl);
- if (hw->chip_id != CHIP_ID_YUKON_FE &&
- skge->flow_control == FLOW_MODE_REM_SEND) {
+ if (skge->flow_status == FLOW_STAT_REM_SEND) {
+ ctrl = gm_phy_read(hw, port, PHY_MARV_AUNE_ADV);
+ ctrl |= PHY_M_AN_ASP;
/* restore Asymmetric Pause bit */
- gm_phy_write(hw, port, PHY_MARV_AUNE_ADV,
- gm_phy_read(hw, port,
- PHY_MARV_AUNE_ADV)
- | PHY_M_AN_ASP);
-
+ gm_phy_write(hw, port, PHY_MARV_AUNE_ADV, ctrl);
}
- yukon_reset(hw, port);
skge_link_down(skge);
yukon_init(hw, port);
istatus = gm_phy_read(hw, port, PHY_MARV_INT_STAT);
phystat = gm_phy_read(hw, port, PHY_MARV_PHY_STAT);
- pr_debug("yukon phy intr istat=%x phy_stat=%x\n", istatus, phystat);
+
+ if (netif_msg_intr(skge))
+ printk(KERN_DEBUG PFX "%s: phy interrupt status 0x%x 0x%x\n",
+ skge->netdev->name, istatus, phystat);
if (istatus & PHY_M_IS_AN_COMPL) {
if (gm_phy_read(hw, port, PHY_MARV_AUNE_LP)
goto failed;
}
- if (!(hw->chip_id == CHIP_ID_YUKON_FE || hw->chip_id == CHIP_ID_YUKON_EC)
- && (gm_phy_read(hw, port, PHY_MARV_1000T_STAT)
- & PHY_B_1000S_MSF)) {
+ if (gm_phy_read(hw, port, PHY_MARV_1000T_STAT) & PHY_B_1000S_MSF) {
reason = "master/slave fault";
goto failed;
}
? DUPLEX_FULL : DUPLEX_HALF;
skge->speed = yukon_speed(hw, phystat);
- /* Tx & Rx Pause Enabled bits are at 9..8 */
- if (hw->chip_id == CHIP_ID_YUKON_XL)
- phystat >>= 6;
-
/* We are using IEEE 802.3z/D5.0 Table 37-4 */
switch (phystat & PHY_M_PS_PAUSE_MSK) {
case PHY_M_PS_PAUSE_MSK:
- skge->flow_control = FLOW_MODE_SYMMETRIC;
+ skge->flow_status = FLOW_STAT_SYMMETRIC;
break;
case PHY_M_PS_RX_P_EN:
- skge->flow_control = FLOW_MODE_REM_SEND;
+ skge->flow_status = FLOW_STAT_REM_SEND;
break;
case PHY_M_PS_TX_P_EN:
- skge->flow_control = FLOW_MODE_LOC_SEND;
+ skge->flow_status = FLOW_STAT_LOC_SEND;
break;
default:
- skge->flow_control = FLOW_MODE_NONE;
+ skge->flow_status = FLOW_STAT_NONE;
}
- if (skge->flow_control == FLOW_MODE_NONE ||
+ if (skge->flow_status == FLOW_STAT_NONE ||
(skge->speed < SPEED_1000 && skge->duplex == DUPLEX_HALF))
skge_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
else
/* XXX restart autonegotiation? */
}
+static void skge_phy_reset(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ struct net_device *dev = hw->dev[port];
+
+ netif_stop_queue(skge->netdev);
+ netif_carrier_off(skge->netdev);
+
+ spin_lock_bh(&hw->phy_lock);
+ if (hw->chip_id == CHIP_ID_GENESIS) {
+ genesis_reset(hw, port);
+ genesis_mac_init(hw, port);
+ } else {
+ yukon_reset(hw, port);
+ yukon_init(hw, port);
+ }
+ spin_unlock_bh(&hw->phy_lock);
+
+ skge_set_multicast(dev);
+}
+
+/* Basic MII support */
+static int skge_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
+{
+ struct mii_ioctl_data *data = if_mii(ifr);
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ int err = -EOPNOTSUPP;
+
+ if (!netif_running(dev))
+ return -ENODEV; /* Phy still in reset */
+
+ switch(cmd) {
+ case SIOCGMIIPHY:
+ data->phy_id = hw->phy_addr;
+
+ /* fallthru */
+ case SIOCGMIIREG: {
+ u16 val = 0;
+ spin_lock_bh(&hw->phy_lock);
+ if (hw->chip_id == CHIP_ID_GENESIS)
+ err = __xm_phy_read(hw, skge->port, data->reg_num & 0x1f, &val);
+ else
+ err = __gm_phy_read(hw, skge->port, data->reg_num & 0x1f, &val);
+ spin_unlock_bh(&hw->phy_lock);
+ data->val_out = val;
+ break;
+ }
+
+ case SIOCSMIIREG:
+ if (!capable(CAP_NET_ADMIN))
+ return -EPERM;
+
+ spin_lock_bh(&hw->phy_lock);
+ if (hw->chip_id == CHIP_ID_GENESIS)
+ err = xm_phy_write(hw, skge->port, data->reg_num & 0x1f,
+ data->val_in);
+ else
+ err = gm_phy_write(hw, skge->port, data->reg_num & 0x1f,
+ data->val_in);
+ spin_unlock_bh(&hw->phy_lock);
+ break;
+ }
+ return err;
+}
+
static void skge_ramset(struct skge_hw *hw, u16 q, u32 start, size_t len)
{
u32 end;
size_t rx_size, tx_size;
int err;
+ if (!is_valid_ether_addr(dev->dev_addr))
+ return -EINVAL;
+
if (netif_msg_ifup(skge))
printk(KERN_INFO PFX "%s: enabling interface\n", dev->name);
+ if (dev->mtu > RX_BUF_SIZE)
+ skge->rx_buf_size = dev->mtu + ETH_HLEN;
+ else
+ skge->rx_buf_size = RX_BUF_SIZE;
+
+
rx_size = skge->rx_ring.count * sizeof(struct skge_rx_desc);
tx_size = skge->tx_ring.count * sizeof(struct skge_tx_desc);
skge->mem_size = tx_size + rx_size;
if (!skge->mem)
return -ENOMEM;
+ BUG_ON(skge->dma & 7);
+
+ if ((u64)skge->dma >> 32 != ((u64) skge->dma + skge->mem_size) >> 32) {
+ dev_err(&hw->pdev->dev, "pci_alloc_consistent region crosses 4G boundary\n");
+ err = -EINVAL;
+ goto free_pci_mem;
+ }
+
memset(skge->mem, 0, skge->mem_size);
- if ((err = skge_ring_alloc(&skge->rx_ring, skge->mem, skge->dma)))
+ err = skge_ring_alloc(&skge->rx_ring, skge->mem, skge->dma);
+ if (err)
goto free_pci_mem;
- if (skge_rx_fill(skge))
+ err = skge_rx_fill(dev);
+ if (err)
goto free_rx_ring;
- if ((err = skge_ring_alloc(&skge->tx_ring, skge->mem + rx_size,
- skge->dma + rx_size)))
+ err = skge_ring_alloc(&skge->tx_ring, skge->mem + rx_size,
+ skge->dma + rx_size);
+ if (err)
goto free_rx_ring;
- skge->tx_avail = skge->tx_ring.count - 1;
-
- /* Initialze MAC */
+ /* Initialize MAC */
+ spin_lock_bh(&hw->phy_lock);
if (hw->chip_id == CHIP_ID_GENESIS)
genesis_mac_init(hw, port);
else
yukon_mac_init(hw, port);
+ spin_unlock_bh(&hw->phy_lock);
- /* Configure RAMbuffers */
- chunk = hw->ram_size / ((hw->ports + 1)*2);
+ /* Configure RAMbuffers - equally between ports and tx/rx */
+ chunk = (hw->ram_size - hw->ram_offset) / (hw->ports * 2);
ram_addr = hw->ram_offset + 2 * chunk * port;
skge_ramset(hw, rxqaddr[port], ram_addr, chunk);
/* Start receiver BMU */
wmb();
skge_write8(hw, Q_ADDR(rxqaddr[port], Q_CSR), CSR_START | CSR_IRQ_CL_F);
+ skge_led(skge, LED_MODE_ON);
+
+ spin_lock_irq(&hw->hw_lock);
+ hw->intr_mask |= portmask[port];
+ skge_write32(hw, B0_IMSK, hw->intr_mask);
+ spin_unlock_irq(&hw->hw_lock);
- pr_debug("skge_up completed\n");
+ napi_enable(&skge->napi);
return 0;
free_rx_ring:
kfree(skge->rx_ring.start);
free_pci_mem:
pci_free_consistent(hw->pdev, skge->mem_size, skge->mem, skge->dma);
+ skge->mem = NULL;
return err;
}
+/* stop receiver */
+static void skge_rx_stop(struct skge_hw *hw, int port)
+{
+ skge_write8(hw, Q_ADDR(rxqaddr[port], Q_CSR), CSR_STOP);
+ skge_write32(hw, RB_ADDR(port ? Q_R2 : Q_R1, RB_CTRL),
+ RB_RST_SET|RB_DIS_OP_MD);
+ skge_write32(hw, Q_ADDR(rxqaddr[port], Q_CSR), CSR_SET_RESET);
+}
+
static int skge_down(struct net_device *dev)
{
struct skge_port *skge = netdev_priv(dev);
struct skge_hw *hw = skge->hw;
int port = skge->port;
+ if (skge->mem == NULL)
+ return 0;
+
if (netif_msg_ifdown(skge))
printk(KERN_INFO PFX "%s: disabling interface\n", dev->name);
- netif_stop_queue(dev);
+ netif_tx_disable(dev);
- del_timer_sync(&skge->led_blink);
- del_timer_sync(&skge->link_check);
+ if (hw->chip_id == CHIP_ID_GENESIS && hw->phy_type == SK_PHY_XMAC)
+ del_timer_sync(&skge->link_timer);
- /* Stop transmitter */
- skge_write8(hw, Q_ADDR(txqaddr[port], Q_CSR), CSR_STOP);
- skge_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL),
- RB_RST_SET|RB_DIS_OP_MD);
+ napi_disable(&skge->napi);
+ netif_carrier_off(dev);
+
+ spin_lock_irq(&hw->hw_lock);
+ hw->intr_mask &= ~portmask[port];
+ skge_write32(hw, B0_IMSK, hw->intr_mask);
+ spin_unlock_irq(&hw->hw_lock);
+ skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG), LED_OFF);
if (hw->chip_id == CHIP_ID_GENESIS)
genesis_stop(skge);
else
yukon_stop(skge);
+ /* Stop transmitter */
+ skge_write8(hw, Q_ADDR(txqaddr[port], Q_CSR), CSR_STOP);
+ skge_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL),
+ RB_RST_SET|RB_DIS_OP_MD);
+
+
/* Disable Force Sync bit and Enable Alloc bit */
skge_write8(hw, SK_REG(port, TXA_CTRL),
TXA_DIS_FSYNC | TXA_DIS_ALLOC | TXA_STOP_RC);
/* Reset the RAM Buffer async Tx queue */
skge_write8(hw, RB_ADDR(port == 0 ? Q_XA1 : Q_XA2, RB_CTRL), RB_RST_SET);
- /* stop receiver */
- skge_write8(hw, Q_ADDR(rxqaddr[port], Q_CSR), CSR_STOP);
- skge_write32(hw, RB_ADDR(port ? Q_R2 : Q_R1, RB_CTRL),
- RB_RST_SET|RB_DIS_OP_MD);
- skge_write32(hw, Q_ADDR(rxqaddr[port], Q_CSR), CSR_SET_RESET);
+
+ skge_rx_stop(hw, port);
if (hw->chip_id == CHIP_ID_GENESIS) {
skge_write8(hw, SK_REG(port, TX_MFF_CTRL2), MFF_RST_SET);
skge_write8(hw, SK_REG(port, RX_MFF_CTRL2), MFF_RST_SET);
- skge_write8(hw, SK_REG(port, TX_LED_CTRL), LED_STOP);
- skge_write8(hw, SK_REG(port, RX_LED_CTRL), LED_STOP);
} else {
skge_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET);
skge_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_SET);
}
- /* turn off led's */
- skge_write16(hw, B0_LED, LED_STAT_OFF);
+ skge_led(skge, LED_MODE_OFF);
+
+ netif_tx_lock_bh(dev);
+ skge_tx_clean(dev);
+ netif_tx_unlock_bh(dev);
- skge_tx_clean(skge);
skge_rx_clean(skge);
kfree(skge->rx_ring.start);
kfree(skge->tx_ring.start);
pci_free_consistent(hw->pdev, skge->mem_size, skge->mem, skge->dma);
+ skge->mem = NULL;
return 0;
}
+static inline int skge_avail(const struct skge_ring *ring)
+{
+ smp_mb();
+ return ((ring->to_clean > ring->to_use) ? 0 : ring->count)
+ + (ring->to_clean - ring->to_use) - 1;
+}
+
static int skge_xmit_frame(struct sk_buff *skb, struct net_device *dev)
{
struct skge_port *skge = netdev_priv(dev);
struct skge_hw *hw = skge->hw;
- struct skge_ring *ring = &skge->tx_ring;
struct skge_element *e;
struct skge_tx_desc *td;
int i;
u32 control, len;
u64 map;
- unsigned long flags;
- skb = skb_padto(skb, ETH_ZLEN);
- if (!skb)
+ if (skb_padto(skb, ETH_ZLEN))
return NETDEV_TX_OK;
- local_irq_save(flags);
- if (!spin_trylock(&skge->tx_lock)) {
- /* Collision - tell upper layer to requeue */
- local_irq_restore(flags);
- return NETDEV_TX_LOCKED;
- }
-
- if (unlikely(skge->tx_avail < skb_shinfo(skb)->nr_frags +1)) {
- netif_stop_queue(dev);
- spin_unlock_irqrestore(&skge->tx_lock, flags);
-
- printk(KERN_WARNING PFX "%s: ring full when queue awake!\n",
- dev->name);
+ if (unlikely(skge_avail(&skge->tx_ring) < skb_shinfo(skb)->nr_frags + 1))
return NETDEV_TX_BUSY;
- }
- e = ring->to_use;
+ e = skge->tx_ring.to_use;
td = e->desc;
+ BUG_ON(td->control & BMU_OWN);
e->skb = skb;
len = skb_headlen(skb);
map = pci_map_single(hw->pdev, skb->data, len, PCI_DMA_TODEVICE);
td->dma_lo = map;
td->dma_hi = map >> 32;
- if (skb->ip_summed == CHECKSUM_HW) {
- const struct iphdr *ip
- = (const struct iphdr *) (skb->data + ETH_HLEN);
- int offset = skb->h.raw - skb->data;
+ if (skb->ip_summed == CHECKSUM_PARTIAL) {
+ const int offset = skb_transport_offset(skb);
/* This seems backwards, but it is what the sk98lin
* does. Looks like hardware is wrong?
*/
- if (ip->protocol == IPPROTO_UDP
+ if (ipip_hdr(skb)->protocol == IPPROTO_UDP
&& hw->chip_rev == 0 && hw->chip_id == CHIP_ID_YUKON)
control = BMU_TCP_CHECK;
else
td->csum_offs = 0;
td->csum_start = offset;
- td->csum_write = offset + skb->csum;
+ td->csum_write = offset + skb->csum_offset;
} else
control = BMU_CHECK;
frag->size, PCI_DMA_TODEVICE);
e = e->next;
- e->skb = NULL;
+ e->skb = skb;
tf = e->desc;
+ BUG_ON(tf->control & BMU_OWN);
+
tf->dma_lo = map;
tf->dma_hi = (u64) map >> 32;
pci_unmap_addr_set(e, mapaddr, map);
skge_write8(hw, Q_ADDR(txqaddr[skge->port], Q_CSR), CSR_START);
- if (netif_msg_tx_queued(skge))
+ if (unlikely(netif_msg_tx_queued(skge)))
printk(KERN_DEBUG "%s: tx queued, slot %td, len %d\n",
- dev->name, e - ring->start, skb->len);
+ dev->name, e - skge->tx_ring.start, skb->len);
+
+ skge->tx_ring.to_use = e->next;
+ smp_wmb();
- ring->to_use = e->next;
- skge->tx_avail -= skb_shinfo(skb)->nr_frags + 1;
- if (skge->tx_avail <= MAX_SKB_FRAGS + 1) {
+ if (skge_avail(&skge->tx_ring) <= TX_LOW_WATER) {
pr_debug("%s: transmit queue full\n", dev->name);
netif_stop_queue(dev);
}
- dev->trans_start = jiffies;
- spin_unlock_irqrestore(&skge->tx_lock, flags);
-
return NETDEV_TX_OK;
}
-static inline void skge_tx_free(struct skge_hw *hw, struct skge_element *e)
+
+/* Free resources associated with this reing element */
+static void skge_tx_free(struct skge_port *skge, struct skge_element *e,
+ u32 control)
{
- if (e->skb) {
- pci_unmap_single(hw->pdev,
- pci_unmap_addr(e, mapaddr),
- pci_unmap_len(e, maplen),
- PCI_DMA_TODEVICE);
- dev_kfree_skb_any(e->skb);
- e->skb = NULL;
- } else {
- pci_unmap_page(hw->pdev,
- pci_unmap_addr(e, mapaddr),
+ struct pci_dev *pdev = skge->hw->pdev;
+
+ /* skb header vs. fragment */
+ if (control & BMU_STF)
+ pci_unmap_single(pdev, pci_unmap_addr(e, mapaddr),
+ pci_unmap_len(e, maplen),
+ PCI_DMA_TODEVICE);
+ else
+ pci_unmap_page(pdev, pci_unmap_addr(e, mapaddr),
pci_unmap_len(e, maplen),
PCI_DMA_TODEVICE);
+
+ if (control & BMU_EOF) {
+ if (unlikely(netif_msg_tx_done(skge)))
+ printk(KERN_DEBUG PFX "%s: tx done slot %td\n",
+ skge->netdev->name, e - skge->tx_ring.start);
+
+ dev_kfree_skb(e->skb);
}
}
-static void skge_tx_clean(struct skge_port *skge)
+/* Free all buffers in transmit ring */
+static void skge_tx_clean(struct net_device *dev)
{
- struct skge_ring *ring = &skge->tx_ring;
+ struct skge_port *skge = netdev_priv(dev);
struct skge_element *e;
- unsigned long flags;
- spin_lock_irqsave(&skge->tx_lock, flags);
- for (e = ring->to_clean; e != ring->to_use; e = e->next) {
- ++skge->tx_avail;
- skge_tx_free(skge->hw, e);
+ for (e = skge->tx_ring.to_clean; e != skge->tx_ring.to_use; e = e->next) {
+ struct skge_tx_desc *td = e->desc;
+ skge_tx_free(skge, e, td->control);
+ td->control = 0;
}
- ring->to_clean = e;
- spin_unlock_irqrestore(&skge->tx_lock, flags);
+
+ skge->tx_ring.to_clean = e;
}
static void skge_tx_timeout(struct net_device *dev)
printk(KERN_DEBUG PFX "%s: tx timeout\n", dev->name);
skge_write8(skge->hw, Q_ADDR(txqaddr[skge->port], Q_CSR), CSR_STOP);
- skge_tx_clean(skge);
+ skge_tx_clean(dev);
+ netif_wake_queue(dev);
}
static int skge_change_mtu(struct net_device *dev, int new_mtu)
{
- int err = 0;
+ int err;
if (new_mtu < ETH_ZLEN || new_mtu > ETH_JUMBO_MTU)
return -EINVAL;
+ if (!netif_running(dev)) {
+ dev->mtu = new_mtu;
+ return 0;
+ }
+
+ skge_down(dev);
+
dev->mtu = new_mtu;
- if (netif_running(dev)) {
- skge_down(dev);
- skge_up(dev);
- }
+ err = skge_up(dev);
+ if (err)
+ dev_close(dev);
return err;
}
+static const u8 pause_mc_addr[ETH_ALEN] = { 0x1, 0x80, 0xc2, 0x0, 0x0, 0x1 };
+
+static void genesis_add_filter(u8 filter[8], const u8 *addr)
+{
+ u32 crc, bit;
+
+ crc = ether_crc_le(ETH_ALEN, addr);
+ bit = ~crc & 0x3f;
+ filter[bit/8] |= 1 << (bit%8);
+}
+
static void genesis_set_multicast(struct net_device *dev)
{
struct skge_port *skge = netdev_priv(dev);
memset(filter, 0xff, sizeof(filter));
else {
memset(filter, 0, sizeof(filter));
- for (i = 0; list && i < count; i++, list = list->next) {
- u32 crc = crc32_le(~0, list->dmi_addr, ETH_ALEN);
- u8 bit = 63 - (crc & 63);
- filter[bit/8] |= 1 << (bit%8);
- }
+ if (skge->flow_status == FLOW_STAT_REM_SEND
+ || skge->flow_status == FLOW_STAT_SYMMETRIC)
+ genesis_add_filter(filter, pause_mc_addr);
+
+ for (i = 0; list && i < count; i++, list = list->next)
+ genesis_add_filter(filter, list->dmi_addr);
}
+ xm_write32(hw, port, XM_MODE, mode);
xm_outhash(hw, port, XM_HSM, filter);
+}
- xm_write32(hw, port, XM_MODE, mode);
+static void yukon_add_filter(u8 filter[8], const u8 *addr)
+{
+ u32 bit = ether_crc(ETH_ALEN, addr) & 0x3f;
+ filter[bit/8] |= 1 << (bit%8);
}
static void yukon_set_multicast(struct net_device *dev)
struct skge_hw *hw = skge->hw;
int port = skge->port;
struct dev_mc_list *list = dev->mc_list;
+ int rx_pause = (skge->flow_status == FLOW_STAT_REM_SEND
+ || skge->flow_status == FLOW_STAT_SYMMETRIC);
u16 reg;
u8 filter[8];
reg = gma_read16(hw, port, GM_RX_CTRL);
reg |= GM_RXCR_UCF_ENA;
- if (dev->flags & IFF_PROMISC) /* promiscious */
+ if (dev->flags & IFF_PROMISC) /* promiscuous */
reg &= ~(GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA);
else if (dev->flags & IFF_ALLMULTI) /* all multicast */
memset(filter, 0xff, sizeof(filter));
- else if (dev->mc_count == 0) /* no multicast */
+ else if (dev->mc_count == 0 && !rx_pause)/* no multicast */
reg &= ~GM_RXCR_MCF_ENA;
else {
int i;
reg |= GM_RXCR_MCF_ENA;
- for (i = 0; list && i < dev->mc_count; i++, list = list->next) {
- u32 bit = ether_crc(ETH_ALEN, list->dmi_addr) & 0x3f;
- filter[bit/8] |= 1 << (bit%8);
- }
+ if (rx_pause)
+ yukon_add_filter(filter, pause_mc_addr);
+
+ for (i = 0; list && i < dev->mc_count; i++, list = list->next)
+ yukon_add_filter(filter, list->dmi_addr);
}
gma_write16(hw, port, GM_RX_CTRL, reg);
}
+static inline u16 phy_length(const struct skge_hw *hw, u32 status)
+{
+ if (hw->chip_id == CHIP_ID_GENESIS)
+ return status >> XMR_FS_LEN_SHIFT;
+ else
+ return status >> GMR_FS_LEN_SHIFT;
+}
+
static inline int bad_phy_status(const struct skge_hw *hw, u32 status)
{
if (hw->chip_id == CHIP_ID_GENESIS)
(status & GMR_FS_RX_OK) == 0;
}
-static void skge_rx_error(struct skge_port *skge, int slot,
- u32 control, u32 status)
-{
- if (netif_msg_rx_err(skge))
- printk(KERN_DEBUG PFX "%s: rx err, slot %d control 0x%x status 0x%x\n",
- skge->netdev->name, slot, control, status);
-
- if ((control & (BMU_EOF|BMU_STF)) != (BMU_STF|BMU_EOF)
- || (control & BMU_BBC) > skge->netdev->mtu + VLAN_ETH_HLEN)
- skge->net_stats.rx_length_errors++;
- else {
- if (skge->hw->chip_id == CHIP_ID_GENESIS) {
- if (status & (XMR_FS_RUNT|XMR_FS_LNG_ERR))
- skge->net_stats.rx_length_errors++;
- if (status & XMR_FS_FRA_ERR)
- skge->net_stats.rx_frame_errors++;
- if (status & XMR_FS_FCS_ERR)
- skge->net_stats.rx_crc_errors++;
- } else {
- if (status & (GMR_FS_LONG_ERR|GMR_FS_UN_SIZE))
- skge->net_stats.rx_length_errors++;
- if (status & GMR_FS_FRAGMENT)
- skge->net_stats.rx_frame_errors++;
- if (status & GMR_FS_CRC_ERR)
- skge->net_stats.rx_crc_errors++;
- }
- }
-}
-
-static int skge_poll(struct net_device *dev, int *budget)
+static void skge_set_multicast(struct net_device *dev)
{
struct skge_port *skge = netdev_priv(dev);
struct skge_hw *hw = skge->hw;
- struct skge_ring *ring = &skge->rx_ring;
- struct skge_element *e;
- unsigned int to_do = min(dev->quota, *budget);
- unsigned int work_done = 0;
- int done;
- static const u32 irqmask[] = { IS_PORT_1, IS_PORT_2 };
- for (e = ring->to_clean; e != ring->to_use && work_done < to_do;
- e = e->next) {
- struct skge_rx_desc *rd = e->desc;
- struct sk_buff *skb = e->skb;
- u32 control, len, status;
+ if (hw->chip_id == CHIP_ID_GENESIS)
+ genesis_set_multicast(dev);
+ else
+ yukon_set_multicast(dev);
+
+}
- rmb();
- control = rd->control;
- if (control & BMU_OWN)
- break;
- len = control & BMU_BBC;
- e->skb = NULL;
+/* Get receive buffer from descriptor.
+ * Handles copy of small buffers and reallocation failures
+ */
+static struct sk_buff *skge_rx_get(struct net_device *dev,
+ struct skge_element *e,
+ u32 control, u32 status, u16 csum)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct sk_buff *skb;
+ u16 len = control & BMU_BBC;
+
+ if (unlikely(netif_msg_rx_status(skge)))
+ printk(KERN_DEBUG PFX "%s: rx slot %td status 0x%x len %d\n",
+ dev->name, e - skge->rx_ring.start,
+ status, len);
+
+ if (len > skge->rx_buf_size)
+ goto error;
+
+ if ((control & (BMU_EOF|BMU_STF)) != (BMU_STF|BMU_EOF))
+ goto error;
+
+ if (bad_phy_status(skge->hw, status))
+ goto error;
+
+ if (phy_length(skge->hw, status) != len)
+ goto error;
+
+ if (len < RX_COPY_THRESHOLD) {
+ skb = netdev_alloc_skb(dev, len + 2);
+ if (!skb)
+ goto resubmit;
+
+ skb_reserve(skb, 2);
+ pci_dma_sync_single_for_cpu(skge->hw->pdev,
+ pci_unmap_addr(e, mapaddr),
+ len, PCI_DMA_FROMDEVICE);
+ skb_copy_from_linear_data(e->skb, skb->data, len);
+ pci_dma_sync_single_for_device(skge->hw->pdev,
+ pci_unmap_addr(e, mapaddr),
+ len, PCI_DMA_FROMDEVICE);
+ skge_rx_reuse(e, skge->rx_buf_size);
+ } else {
+ struct sk_buff *nskb;
+ nskb = netdev_alloc_skb(dev, skge->rx_buf_size + NET_IP_ALIGN);
+ if (!nskb)
+ goto resubmit;
- pci_unmap_single(hw->pdev,
+ skb_reserve(nskb, NET_IP_ALIGN);
+ pci_unmap_single(skge->hw->pdev,
pci_unmap_addr(e, mapaddr),
pci_unmap_len(e, maplen),
PCI_DMA_FROMDEVICE);
+ skb = e->skb;
+ prefetch(skb->data);
+ skge_rx_setup(skge, e, nskb, skge->rx_buf_size);
+ }
- status = rd->status;
- if ((control & (BMU_EOF|BMU_STF)) != (BMU_STF|BMU_EOF)
- || len > dev->mtu + VLAN_ETH_HLEN
- || bad_phy_status(hw, status)) {
- skge_rx_error(skge, e - ring->start, control, status);
- dev_kfree_skb(skb);
- continue;
- }
+ skb_put(skb, len);
+ if (skge->rx_csum) {
+ skb->csum = csum;
+ skb->ip_summed = CHECKSUM_COMPLETE;
+ }
- if (netif_msg_rx_status(skge))
- printk(KERN_DEBUG PFX "%s: rx slot %td status 0x%x len %d\n",
- dev->name, e - ring->start, rd->status, len);
+ skb->protocol = eth_type_trans(skb, dev);
- skb_put(skb, len);
- skb->protocol = eth_type_trans(skb, dev);
+ return skb;
+error:
- if (skge->rx_csum) {
- skb->csum = le16_to_cpu(rd->csum2);
- skb->ip_summed = CHECKSUM_HW;
- }
+ if (netif_msg_rx_err(skge))
+ printk(KERN_DEBUG PFX "%s: rx err, slot %td control 0x%x status 0x%x\n",
+ dev->name, e - skge->rx_ring.start,
+ control, status);
+
+ if (skge->hw->chip_id == CHIP_ID_GENESIS) {
+ if (status & (XMR_FS_RUNT|XMR_FS_LNG_ERR))
+ dev->stats.rx_length_errors++;
+ if (status & XMR_FS_FRA_ERR)
+ dev->stats.rx_frame_errors++;
+ if (status & XMR_FS_FCS_ERR)
+ dev->stats.rx_crc_errors++;
+ } else {
+ if (status & (GMR_FS_LONG_ERR|GMR_FS_UN_SIZE))
+ dev->stats.rx_length_errors++;
+ if (status & GMR_FS_FRAGMENT)
+ dev->stats.rx_frame_errors++;
+ if (status & GMR_FS_CRC_ERR)
+ dev->stats.rx_crc_errors++;
+ }
- dev->last_rx = jiffies;
- netif_receive_skb(skb);
+resubmit:
+ skge_rx_reuse(e, skge->rx_buf_size);
+ return NULL;
+}
- ++work_done;
- }
- ring->to_clean = e;
+/* Free all buffers in Tx ring which are no longer owned by device */
+static void skge_tx_done(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_ring *ring = &skge->tx_ring;
+ struct skge_element *e;
- *budget -= work_done;
- dev->quota -= work_done;
- done = work_done < to_do;
+ skge_write8(skge->hw, Q_ADDR(txqaddr[skge->port], Q_CSR), CSR_IRQ_CL_F);
- if (skge_rx_fill(skge))
- done = 0;
+ for (e = ring->to_clean; e != ring->to_use; e = e->next) {
+ u32 control = ((const struct skge_tx_desc *) e->desc)->control;
- /* restart receiver */
- wmb();
- skge_write8(hw, Q_ADDR(rxqaddr[skge->port], Q_CSR),
- CSR_START | CSR_IRQ_CL_F);
+ if (control & BMU_OWN)
+ break;
- if (done) {
- local_irq_disable();
- hw->intr_mask |= irqmask[skge->port];
- /* Order is important since data can get interrupted */
- skge_write32(hw, B0_IMSK, hw->intr_mask);
- __netif_rx_complete(dev);
- local_irq_enable();
+ skge_tx_free(skge, e, control);
}
+ skge->tx_ring.to_clean = e;
+
+ /* Can run lockless until we need to synchronize to restart queue. */
+ smp_mb();
- return !done;
+ if (unlikely(netif_queue_stopped(dev) &&
+ skge_avail(&skge->tx_ring) > TX_LOW_WATER)) {
+ netif_tx_lock(dev);
+ if (unlikely(netif_queue_stopped(dev) &&
+ skge_avail(&skge->tx_ring) > TX_LOW_WATER)) {
+ netif_wake_queue(dev);
+
+ }
+ netif_tx_unlock(dev);
+ }
}
-static inline void skge_tx_intr(struct net_device *dev)
+static int skge_poll(struct napi_struct *napi, int to_do)
{
- struct skge_port *skge = netdev_priv(dev);
+ struct skge_port *skge = container_of(napi, struct skge_port, napi);
+ struct net_device *dev = skge->netdev;
struct skge_hw *hw = skge->hw;
- struct skge_ring *ring = &skge->tx_ring;
+ struct skge_ring *ring = &skge->rx_ring;
struct skge_element *e;
+ int work_done = 0;
- spin_lock(&skge->tx_lock);
- for (e = ring->to_clean; e != ring->to_use; e = e->next) {
- struct skge_tx_desc *td = e->desc;
+ skge_tx_done(dev);
+
+ skge_write8(hw, Q_ADDR(rxqaddr[skge->port], Q_CSR), CSR_IRQ_CL_F);
+
+ for (e = ring->to_clean; prefetch(e->next), work_done < to_do; e = e->next) {
+ struct skge_rx_desc *rd = e->desc;
+ struct sk_buff *skb;
u32 control;
rmb();
- control = td->control;
+ control = rd->control;
if (control & BMU_OWN)
break;
- if (unlikely(netif_msg_tx_done(skge)))
- printk(KERN_DEBUG PFX "%s: tx done slot %td status 0x%x\n",
- dev->name, e - ring->start, td->status);
+ skb = skge_rx_get(dev, e, control, rd->status, rd->csum2);
+ if (likely(skb)) {
+ netif_receive_skb(skb);
- skge_tx_free(hw, e);
- e->skb = NULL;
- ++skge->tx_avail;
+ ++work_done;
+ }
}
ring->to_clean = e;
- skge_write8(hw, Q_ADDR(txqaddr[skge->port], Q_CSR), CSR_IRQ_CL_F);
- if (skge->tx_avail > MAX_SKB_FRAGS + 1)
- netif_wake_queue(dev);
+ /* restart receiver */
+ wmb();
+ skge_write8(hw, Q_ADDR(rxqaddr[skge->port], Q_CSR), CSR_START);
+
+ if (work_done < to_do) {
+ unsigned long flags;
+
+ spin_lock_irqsave(&hw->hw_lock, flags);
+ __napi_complete(napi);
+ hw->intr_mask |= napimask[skge->port];
+ skge_write32(hw, B0_IMSK, hw->intr_mask);
+ skge_read32(hw, B0_IMSK);
+ spin_unlock_irqrestore(&hw->hw_lock, flags);
+ }
- spin_unlock(&skge->tx_lock);
+ return work_done;
}
+/* Parity errors seem to happen when Genesis is connected to a switch
+ * with no other ports present. Heartbeat error??
+ */
static void skge_mac_parity(struct skge_hw *hw, int port)
{
- printk(KERN_ERR PFX "%s: mac data parity error\n",
- hw->dev[port] ? hw->dev[port]->name
- : (port == 0 ? "(port A)": "(port B"));
+ struct net_device *dev = hw->dev[port];
+
+ ++dev->stats.tx_heartbeat_errors;
if (hw->chip_id == CHIP_ID_GENESIS)
skge_write16(hw, SK_REG(port, TX_MFF_CTRL1),
? GMF_CLI_TX_FC : GMF_CLI_TX_PE);
}
-static void skge_pci_clear(struct skge_hw *hw)
-{
- u16 status;
-
- pci_read_config_word(hw->pdev, PCI_STATUS, &status);
- skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
- pci_write_config_word(hw->pdev, PCI_STATUS,
- status | PCI_STATUS_ERROR_BITS);
- skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
-}
-
static void skge_mac_intr(struct skge_hw *hw, int port)
{
if (hw->chip_id == CHIP_ID_GENESIS)
/* Handle device specific framing and timeout interrupts */
static void skge_error_irq(struct skge_hw *hw)
{
+ struct pci_dev *pdev = hw->pdev;
u32 hwstatus = skge_read32(hw, B0_HWE_ISRC);
if (hw->chip_id == CHIP_ID_GENESIS) {
/* clear xmac errors */
if (hwstatus & (IS_NO_STAT_M1|IS_NO_TIST_M1))
- skge_write16(hw, SK_REG(0, RX_MFF_CTRL1), MFF_CLR_INSTAT);
+ skge_write16(hw, RX_MFF_CTRL1, MFF_CLR_INSTAT);
if (hwstatus & (IS_NO_STAT_M2|IS_NO_TIST_M2))
- skge_write16(hw, SK_REG(0, RX_MFF_CTRL2), MFF_CLR_INSTAT);
+ skge_write16(hw, RX_MFF_CTRL2, MFF_CLR_INSTAT);
} else {
/* Timestamp (unused) overflow */
if (hwstatus & IS_IRQ_TIST_OV)
skge_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ);
-
- if (hwstatus & IS_IRQ_SENSOR) {
- /* no sensors on 32-bit Yukon */
- if (!(skge_read16(hw, B0_CTST) & CS_BUS_SLOT_SZ)) {
- printk(KERN_ERR PFX "ignoring bogus sensor interrups\n");
- skge_write32(hw, B0_HWE_IMSK,
- IS_ERR_MSK & ~IS_IRQ_SENSOR);
- } else
- printk(KERN_WARNING PFX "sensor interrupt\n");
- }
-
-
}
if (hwstatus & IS_RAM_RD_PAR) {
- printk(KERN_ERR PFX "Ram read data parity error\n");
+ dev_err(&pdev->dev, "Ram read data parity error\n");
skge_write16(hw, B3_RI_CTRL, RI_CLR_RD_PERR);
}
if (hwstatus & IS_RAM_WR_PAR) {
- printk(KERN_ERR PFX "Ram write data parity error\n");
+ dev_err(&pdev->dev, "Ram write data parity error\n");
skge_write16(hw, B3_RI_CTRL, RI_CLR_WR_PERR);
}
if (hwstatus & IS_M2_PAR_ERR)
skge_mac_parity(hw, 1);
- if (hwstatus & IS_R1_PAR_ERR)
+ if (hwstatus & IS_R1_PAR_ERR) {
+ dev_err(&pdev->dev, "%s: receive queue parity error\n",
+ hw->dev[0]->name);
skge_write32(hw, B0_R1_CSR, CSR_IRQ_CL_P);
+ }
- if (hwstatus & IS_R2_PAR_ERR)
+ if (hwstatus & IS_R2_PAR_ERR) {
+ dev_err(&pdev->dev, "%s: receive queue parity error\n",
+ hw->dev[1]->name);
skge_write32(hw, B0_R2_CSR, CSR_IRQ_CL_P);
+ }
if (hwstatus & (IS_IRQ_MST_ERR|IS_IRQ_STAT)) {
- printk(KERN_ERR PFX "hardware error detected (status 0x%x)\n",
- hwstatus);
+ u16 pci_status, pci_cmd;
- skge_pci_clear(hw);
+ pci_read_config_word(pdev, PCI_COMMAND, &pci_cmd);
+ pci_read_config_word(pdev, PCI_STATUS, &pci_status);
+ dev_err(&pdev->dev, "PCI error cmd=%#x status=%#x\n",
+ pci_cmd, pci_status);
+
+ /* Write the error bits back to clear them. */
+ pci_status &= PCI_STATUS_ERROR_BITS;
+ skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
+ pci_write_config_word(pdev, PCI_COMMAND,
+ pci_cmd | PCI_COMMAND_SERR | PCI_COMMAND_PARITY);
+ pci_write_config_word(pdev, PCI_STATUS, pci_status);
+ skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
+
+ /* if error still set then just ignore it */
hwstatus = skge_read32(hw, B0_HWE_ISRC);
if (hwstatus & IS_IRQ_STAT) {
- printk(KERN_WARNING PFX "IRQ status %x: still set ignoring hardware errors\n",
- hwstatus);
+ dev_warn(&hw->pdev->dev, "unable to clear error (so ignoring them)\n");
hw->intr_mask &= ~IS_HW_ERR;
}
}
}
/*
- * Interrrupt from PHY are handled in tasklet (soft irq)
+ * Interrupt from PHY are handled in tasklet (softirq)
* because accessing phy registers requires spin wait which might
* cause excess interrupt latency.
*/
-static void skge_extirq(unsigned long data)
+static void skge_extirq(unsigned long arg)
{
- struct skge_hw *hw = (struct skge_hw *) data;
+ struct skge_hw *hw = (struct skge_hw *) arg;
int port;
- spin_lock(&hw->phy_lock);
- for (port = 0; port < 2; port++) {
+ for (port = 0; port < hw->ports; port++) {
struct net_device *dev = hw->dev[port];
- if (dev && netif_running(dev)) {
+ if (netif_running(dev)) {
struct skge_port *skge = netdev_priv(dev);
+ spin_lock(&hw->phy_lock);
if (hw->chip_id != CHIP_ID_GENESIS)
yukon_phy_intr(skge);
else if (hw->phy_type == SK_PHY_BCOM)
- genesis_bcom_intr(skge);
+ bcom_phy_intr(skge);
+ spin_unlock(&hw->phy_lock);
}
}
- spin_unlock(&hw->phy_lock);
- local_irq_disable();
+ spin_lock_irq(&hw->hw_lock);
hw->intr_mask |= IS_EXT_REG;
skge_write32(hw, B0_IMSK, hw->intr_mask);
- local_irq_enable();
+ skge_read32(hw, B0_IMSK);
+ spin_unlock_irq(&hw->hw_lock);
}
-static irqreturn_t skge_intr(int irq, void *dev_id, struct pt_regs *regs)
+static irqreturn_t skge_intr(int irq, void *dev_id)
{
struct skge_hw *hw = dev_id;
- u32 status = skge_read32(hw, B0_SP_ISRC);
+ u32 status;
+ int handled = 0;
- if (status == 0 || status == ~0) /* hotplug or shared irq */
- return IRQ_NONE;
+ spin_lock(&hw->hw_lock);
+ /* Reading this register masks IRQ */
+ status = skge_read32(hw, B0_SP_ISRC);
+ if (status == 0 || status == ~0)
+ goto out;
+ handled = 1;
status &= hw->intr_mask;
-
- if ((status & IS_R1_F) && netif_rx_schedule_prep(hw->dev[0])) {
- status &= ~IS_R1_F;
- hw->intr_mask &= ~IS_R1_F;
- skge_write32(hw, B0_IMSK, hw->intr_mask);
- __netif_rx_schedule(hw->dev[0]);
+ if (status & IS_EXT_REG) {
+ hw->intr_mask &= ~IS_EXT_REG;
+ tasklet_schedule(&hw->phy_task);
}
- if ((status & IS_R2_F) && netif_rx_schedule_prep(hw->dev[1])) {
- status &= ~IS_R2_F;
- hw->intr_mask &= ~IS_R2_F;
- skge_write32(hw, B0_IMSK, hw->intr_mask);
- __netif_rx_schedule(hw->dev[1]);
+ if (status & (IS_XA1_F|IS_R1_F)) {
+ struct skge_port *skge = netdev_priv(hw->dev[0]);
+ hw->intr_mask &= ~(IS_XA1_F|IS_R1_F);
+ napi_schedule(&skge->napi);
}
- if (status & IS_XA1_F)
- skge_tx_intr(hw->dev[0]);
+ if (status & IS_PA_TO_TX1)
+ skge_write16(hw, B3_PA_CTRL, PA_CLR_TO_TX1);
+
+ if (status & IS_PA_TO_RX1) {
+ ++hw->dev[0]->stats.rx_over_errors;
+ skge_write16(hw, B3_PA_CTRL, PA_CLR_TO_RX1);
+ }
- if (status & IS_XA2_F)
- skge_tx_intr(hw->dev[1]);
if (status & IS_MAC1)
skge_mac_intr(hw, 0);
- if (status & IS_MAC2)
- skge_mac_intr(hw, 1);
+ if (hw->dev[1]) {
+ struct skge_port *skge = netdev_priv(hw->dev[1]);
- if (status & IS_HW_ERR)
- skge_error_irq(hw);
+ if (status & (IS_XA2_F|IS_R2_F)) {
+ hw->intr_mask &= ~(IS_XA2_F|IS_R2_F);
+ napi_schedule(&skge->napi);
+ }
- if (status & IS_EXT_REG) {
- hw->intr_mask &= ~IS_EXT_REG;
- tasklet_schedule(&hw->ext_tasklet);
+ if (status & IS_PA_TO_RX2) {
+ ++hw->dev[1]->stats.rx_over_errors;
+ skge_write16(hw, B3_PA_CTRL, PA_CLR_TO_RX2);
+ }
+
+ if (status & IS_PA_TO_TX2)
+ skge_write16(hw, B3_PA_CTRL, PA_CLR_TO_TX2);
+
+ if (status & IS_MAC2)
+ skge_mac_intr(hw, 1);
}
- if (status)
- skge_write32(hw, B0_IMSK, hw->intr_mask);
+ if (status & IS_HW_ERR)
+ skge_error_irq(hw);
- return IRQ_HANDLED;
+ skge_write32(hw, B0_IMSK, hw->intr_mask);
+ skge_read32(hw, B0_IMSK);
+out:
+ spin_unlock(&hw->hw_lock);
+
+ return IRQ_RETVAL(handled);
}
#ifdef CONFIG_NET_POLL_CONTROLLER
struct skge_port *skge = netdev_priv(dev);
disable_irq(dev->irq);
- skge_intr(dev->irq, skge->hw, NULL);
+ skge_intr(dev->irq, skge->hw);
enable_irq(dev->irq);
}
#endif
static int skge_set_mac_address(struct net_device *dev, void *p)
{
struct skge_port *skge = netdev_priv(dev);
- struct sockaddr *addr = p;
- int err = 0;
+ struct skge_hw *hw = skge->hw;
+ unsigned port = skge->port;
+ const struct sockaddr *addr = p;
+ u16 ctrl;
if (!is_valid_ether_addr(addr->sa_data))
return -EADDRNOTAVAIL;
- skge_down(dev);
memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN);
- memcpy_toio(skge->hw->regs + B2_MAC_1 + skge->port*8,
- dev->dev_addr, ETH_ALEN);
- memcpy_toio(skge->hw->regs + B2_MAC_2 + skge->port*8,
- dev->dev_addr, ETH_ALEN);
- if (dev->flags & IFF_UP)
- err = skge_up(dev);
- return err;
+
+ if (!netif_running(dev)) {
+ memcpy_toio(hw->regs + B2_MAC_1 + port*8, dev->dev_addr, ETH_ALEN);
+ memcpy_toio(hw->regs + B2_MAC_2 + port*8, dev->dev_addr, ETH_ALEN);
+ } else {
+ /* disable Rx */
+ spin_lock_bh(&hw->phy_lock);
+ ctrl = gma_read16(hw, port, GM_GP_CTRL);
+ gma_write16(hw, port, GM_GP_CTRL, ctrl & ~GM_GPCR_RX_ENA);
+
+ memcpy_toio(hw->regs + B2_MAC_1 + port*8, dev->dev_addr, ETH_ALEN);
+ memcpy_toio(hw->regs + B2_MAC_2 + port*8, dev->dev_addr, ETH_ALEN);
+
+ if (hw->chip_id == CHIP_ID_GENESIS)
+ xm_outaddr(hw, port, XM_SA, dev->dev_addr);
+ else {
+ gma_set_addr(hw, port, GM_SRC_ADDR_1L, dev->dev_addr);
+ gma_set_addr(hw, port, GM_SRC_ADDR_2L, dev->dev_addr);
+ }
+
+ gma_write16(hw, port, GM_GP_CTRL, ctrl);
+ spin_unlock_bh(&hw->phy_lock);
+ }
+
+ return 0;
}
static const struct {
{ CHIP_ID_YUKON, "Yukon" },
{ CHIP_ID_YUKON_LITE, "Yukon-Lite"},
{ CHIP_ID_YUKON_LP, "Yukon-LP"},
- { CHIP_ID_YUKON_XL, "Yukon-2 XL"},
- { CHIP_ID_YUKON_EC, "YUKON-2 EC"},
- { CHIP_ID_YUKON_FE, "YUKON-2 FE"},
};
static const char *skge_board_name(const struct skge_hw *hw)
*/
static int skge_reset(struct skge_hw *hw)
{
- u16 ctst;
- u8 t8, mac_cfg;
+ u32 reg;
+ u16 ctst, pci_status;
+ u8 t8, mac_cfg, pmd_type;
int i;
ctst = skge_read16(hw, B0_CTST);
skge_write8(hw, B0_CTST, CS_RST_CLR);
/* clear PCI errors, if any */
- skge_pci_clear(hw);
+ skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
+ skge_write8(hw, B2_TST_CTRL2, 0);
+ pci_read_config_word(hw->pdev, PCI_STATUS, &pci_status);
+ pci_write_config_word(hw->pdev, PCI_STATUS,
+ pci_status | PCI_STATUS_ERROR_BITS);
+ skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
skge_write8(hw, B0_CTST, CS_MRST_CLR);
/* restore CLK_RUN bits (for Yukon-Lite) */
hw->chip_id = skge_read8(hw, B2_CHIP_ID);
hw->phy_type = skge_read8(hw, B2_E_1) & 0xf;
- hw->pmd_type = skge_read8(hw, B2_PMD_TYP);
+ pmd_type = skge_read8(hw, B2_PMD_TYP);
+ hw->copper = (pmd_type == 'T' || pmd_type == '1');
switch (hw->chip_id) {
case CHIP_ID_GENESIS:
hw->phy_addr = PHY_ADDR_BCOM;
break;
default:
- printk(KERN_ERR PFX "%s: unsupported phy type 0x%x\n",
- pci_name(hw->pdev), hw->phy_type);
+ dev_err(&hw->pdev->dev, "unsupported phy type 0x%x\n",
+ hw->phy_type);
return -EOPNOTSUPP;
}
break;
case CHIP_ID_YUKON:
case CHIP_ID_YUKON_LITE:
case CHIP_ID_YUKON_LP:
- if (hw->phy_type < SK_PHY_MARV_COPPER && hw->pmd_type != 'S')
- hw->phy_type = SK_PHY_MARV_COPPER;
+ if (hw->phy_type < SK_PHY_MARV_COPPER && pmd_type != 'S')
+ hw->copper = 1;
hw->phy_addr = PHY_ADDR_MARV;
- if (!iscopper(hw))
- hw->phy_type = SK_PHY_MARV_FIBER;
-
break;
default:
- printk(KERN_ERR PFX "%s: unsupported chip type 0x%x\n",
- pci_name(hw->pdev), hw->chip_id);
+ dev_err(&hw->pdev->dev, "unsupported chip type 0x%x\n",
+ hw->chip_id);
return -EOPNOTSUPP;
}
else
hw->ram_size = t8 * 4096;
+ hw->intr_mask = IS_HW_ERR;
+
+ /* Use PHY IRQ for all but fiber based Genesis board */
+ if (!(hw->chip_id == CHIP_ID_GENESIS && hw->phy_type == SK_PHY_XMAC))
+ hw->intr_mask |= IS_EXT_REG;
+
if (hw->chip_id == CHIP_ID_GENESIS)
genesis_init(hw);
else {
/* switch power to VCC (WA for VAUX problem) */
skge_write8(hw, B0_POWER_CTRL,
PC_VAUX_ENA | PC_VCC_ENA | PC_VAUX_OFF | PC_VCC_ON);
+
+ /* avoid boards with stuck Hardware error bits */
+ if ((skge_read32(hw, B0_ISRC) & IS_HW_ERR) &&
+ (skge_read32(hw, B0_HWE_ISRC) & IS_IRQ_SENSOR)) {
+ dev_warn(&hw->pdev->dev, "stuck hardware sensor bit\n");
+ hw->intr_mask &= ~IS_HW_ERR;
+ }
+
+ /* Clear PHY COMA */
+ skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
+ pci_read_config_dword(hw->pdev, PCI_DEV_REG1, ®);
+ reg &= ~PCI_PHY_COMA;
+ pci_write_config_dword(hw->pdev, PCI_DEV_REG1, reg);
+ skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
+
+
for (i = 0; i < hw->ports; i++) {
skge_write16(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_SET);
skge_write16(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_CLR);
skge_write32(hw, B2_IRQM_INI, skge_usecs2clk(hw, 100));
skge_write32(hw, B2_IRQM_CTRL, TIM_START);
- hw->intr_mask = IS_HW_ERR | IS_EXT_REG | IS_PORT_1;
- if (hw->ports > 1)
- hw->intr_mask |= IS_PORT_2;
skge_write32(hw, B0_IMSK, hw->intr_mask);
- if (hw->chip_id != CHIP_ID_GENESIS)
- skge_write8(hw, GMAC_IRQ_MSK, 0);
-
- spin_lock_bh(&hw->phy_lock);
for (i = 0; i < hw->ports; i++) {
if (hw->chip_id == CHIP_ID_GENESIS)
genesis_reset(hw, i);
else
yukon_reset(hw, i);
}
- spin_unlock_bh(&hw->phy_lock);
return 0;
}
+
+#ifdef CONFIG_SKGE_DEBUG
+
+static struct dentry *skge_debug;
+
+static int skge_debug_show(struct seq_file *seq, void *v)
+{
+ struct net_device *dev = seq->private;
+ const struct skge_port *skge = netdev_priv(dev);
+ const struct skge_hw *hw = skge->hw;
+ const struct skge_element *e;
+
+ if (!netif_running(dev))
+ return -ENETDOWN;
+
+ seq_printf(seq, "IRQ src=%x mask=%x\n", skge_read32(hw, B0_ISRC),
+ skge_read32(hw, B0_IMSK));
+
+ seq_printf(seq, "Tx Ring: (%d)\n", skge_avail(&skge->tx_ring));
+ for (e = skge->tx_ring.to_clean; e != skge->tx_ring.to_use; e = e->next) {
+ const struct skge_tx_desc *t = e->desc;
+ seq_printf(seq, "%#x dma=%#x%08x %#x csum=%#x/%x/%x\n",
+ t->control, t->dma_hi, t->dma_lo, t->status,
+ t->csum_offs, t->csum_write, t->csum_start);
+ }
+
+ seq_printf(seq, "\nRx Ring: \n");
+ for (e = skge->rx_ring.to_clean; ; e = e->next) {
+ const struct skge_rx_desc *r = e->desc;
+
+ if (r->control & BMU_OWN)
+ break;
+
+ seq_printf(seq, "%#x dma=%#x%08x %#x %#x csum=%#x/%x\n",
+ r->control, r->dma_hi, r->dma_lo, r->status,
+ r->timestamp, r->csum1, r->csum1_start);
+ }
+
+ return 0;
+}
+
+static int skge_debug_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, skge_debug_show, inode->i_private);
+}
+
+static const struct file_operations skge_debug_fops = {
+ .owner = THIS_MODULE,
+ .open = skge_debug_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
+/*
+ * Use network device events to create/remove/rename
+ * debugfs file entries
+ */
+static int skge_device_event(struct notifier_block *unused,
+ unsigned long event, void *ptr)
+{
+ struct net_device *dev = ptr;
+ struct skge_port *skge;
+ struct dentry *d;
+
+ if (dev->netdev_ops->ndo_open != &skge_up || !skge_debug)
+ goto done;
+
+ skge = netdev_priv(dev);
+ switch(event) {
+ case NETDEV_CHANGENAME:
+ if (skge->debugfs) {
+ d = debugfs_rename(skge_debug, skge->debugfs,
+ skge_debug, dev->name);
+ if (d)
+ skge->debugfs = d;
+ else {
+ pr_info(PFX "%s: rename failed\n", dev->name);
+ debugfs_remove(skge->debugfs);
+ }
+ }
+ break;
+
+ case NETDEV_GOING_DOWN:
+ if (skge->debugfs) {
+ debugfs_remove(skge->debugfs);
+ skge->debugfs = NULL;
+ }
+ break;
+
+ case NETDEV_UP:
+ d = debugfs_create_file(dev->name, S_IRUGO,
+ skge_debug, dev,
+ &skge_debug_fops);
+ if (!d || IS_ERR(d))
+ pr_info(PFX "%s: debugfs create failed\n",
+ dev->name);
+ else
+ skge->debugfs = d;
+ break;
+ }
+
+done:
+ return NOTIFY_DONE;
+}
+
+static struct notifier_block skge_notifier = {
+ .notifier_call = skge_device_event,
+};
+
+
+static __init void skge_debug_init(void)
+{
+ struct dentry *ent;
+
+ ent = debugfs_create_dir("skge", NULL);
+ if (!ent || IS_ERR(ent)) {
+ pr_info(PFX "debugfs create directory failed\n");
+ return;
+ }
+
+ skge_debug = ent;
+ register_netdevice_notifier(&skge_notifier);
+}
+
+static __exit void skge_debug_cleanup(void)
+{
+ if (skge_debug) {
+ unregister_netdevice_notifier(&skge_notifier);
+ debugfs_remove(skge_debug);
+ skge_debug = NULL;
+ }
+}
+
+#else
+#define skge_debug_init()
+#define skge_debug_cleanup()
+#endif
+
+static const struct net_device_ops skge_netdev_ops = {
+ .ndo_open = skge_up,
+ .ndo_stop = skge_down,
+ .ndo_start_xmit = skge_xmit_frame,
+ .ndo_do_ioctl = skge_ioctl,
+ .ndo_get_stats = skge_get_stats,
+ .ndo_tx_timeout = skge_tx_timeout,
+ .ndo_change_mtu = skge_change_mtu,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_set_multicast_list = skge_set_multicast,
+ .ndo_set_mac_address = skge_set_mac_address,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ .ndo_poll_controller = skge_netpoll,
+#endif
+};
+
+
/* Initialize network device */
static struct net_device *skge_devinit(struct skge_hw *hw, int port,
int highmem)
struct net_device *dev = alloc_etherdev(sizeof(*skge));
if (!dev) {
- printk(KERN_ERR "skge etherdev alloc failed");
+ dev_err(&hw->pdev->dev, "etherdev alloc failed\n");
return NULL;
}
- SET_MODULE_OWNER(dev);
SET_NETDEV_DEV(dev, &hw->pdev->dev);
- dev->open = skge_up;
- dev->stop = skge_down;
- dev->hard_start_xmit = skge_xmit_frame;
- dev->get_stats = skge_get_stats;
- if (hw->chip_id == CHIP_ID_GENESIS)
- dev->set_multicast_list = genesis_set_multicast;
- else
- dev->set_multicast_list = yukon_set_multicast;
-
- dev->set_mac_address = skge_set_mac_address;
- dev->change_mtu = skge_change_mtu;
- SET_ETHTOOL_OPS(dev, &skge_ethtool_ops);
- dev->tx_timeout = skge_tx_timeout;
+ dev->netdev_ops = &skge_netdev_ops;
+ dev->ethtool_ops = &skge_ethtool_ops;
dev->watchdog_timeo = TX_WATCHDOG;
- dev->poll = skge_poll;
- dev->weight = NAPI_WEIGHT;
-#ifdef CONFIG_NET_POLL_CONTROLLER
- dev->poll_controller = skge_netpoll;
-#endif
dev->irq = hw->pdev->irq;
- dev->features = NETIF_F_LLTX;
+
if (highmem)
dev->features |= NETIF_F_HIGHDMA;
skge = netdev_priv(dev);
+ netif_napi_add(dev, &skge->napi, skge_poll, NAPI_WEIGHT);
skge->netdev = dev;
skge->hw = hw;
skge->msg_enable = netif_msg_init(debug, default_msg);
+
skge->tx_ring.count = DEFAULT_TX_RING_SIZE;
skge->rx_ring.count = DEFAULT_RX_RING_SIZE;
/* Auto speed and flow control */
skge->autoneg = AUTONEG_ENABLE;
- skge->flow_control = FLOW_MODE_SYMMETRIC;
+ skge->flow_control = FLOW_MODE_SYM_OR_REM;
skge->duplex = -1;
skge->speed = -1;
- skge->advertising = skge_modes(hw);
+ skge->advertising = skge_supported_modes(hw);
+
+ if (device_may_wakeup(&hw->pdev->dev))
+ skge->wol = wol_supported(hw) & WAKE_MAGIC;
hw->dev[port] = dev;
skge->port = port;
- spin_lock_init(&skge->tx_lock);
-
- init_timer(&skge->link_check);
- skge->link_check.function = skge_link_timer;
- skge->link_check.data = (unsigned long) skge;
-
- init_timer(&skge->led_blink);
- skge->led_blink.function = skge_blink_timer;
- skge->led_blink.data = (unsigned long) skge;
+ /* Only used for Genesis XMAC */
+ setup_timer(&skge->link_timer, xm_link_timer, (unsigned long) skge);
if (hw->chip_id != CHIP_ID_GENESIS) {
dev->features |= NETIF_F_IP_CSUM | NETIF_F_SG;
/* read the mac address */
memcpy_fromio(dev->dev_addr, hw->regs + B2_MAC_1 + port*8, ETH_ALEN);
+ memcpy(dev->perm_addr, dev->dev_addr, dev->addr_len);
/* device is off until link detection */
netif_carrier_off(dev);
const struct skge_port *skge = netdev_priv(dev);
if (netif_msg_probe(skge))
- printk(KERN_INFO PFX "%s: addr %02x:%02x:%02x:%02x:%02x:%02x\n",
- dev->name,
- dev->dev_addr[0], dev->dev_addr[1], dev->dev_addr[2],
- dev->dev_addr[3], dev->dev_addr[4], dev->dev_addr[5]);
+ printk(KERN_INFO PFX "%s: addr %pM\n",
+ dev->name, dev->dev_addr);
}
static int __devinit skge_probe(struct pci_dev *pdev,
struct skge_hw *hw;
int err, using_dac = 0;
- if ((err = pci_enable_device(pdev))) {
- printk(KERN_ERR PFX "%s cannot enable PCI device\n",
- pci_name(pdev));
+ err = pci_enable_device(pdev);
+ if (err) {
+ dev_err(&pdev->dev, "cannot enable PCI device\n");
goto err_out;
}
- if ((err = pci_request_regions(pdev, DRV_NAME))) {
- printk(KERN_ERR PFX "%s cannot obtain PCI resources\n",
- pci_name(pdev));
+ err = pci_request_regions(pdev, DRV_NAME);
+ if (err) {
+ dev_err(&pdev->dev, "cannot obtain PCI resources\n");
goto err_out_disable_pdev;
}
pci_set_master(pdev);
- if (!(err = pci_set_dma_mask(pdev, DMA_64BIT_MASK)))
+ if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) {
using_dac = 1;
- else if (!(err = pci_set_dma_mask(pdev, DMA_32BIT_MASK))) {
- printk(KERN_ERR PFX "%s no usable DMA configuration\n",
- pci_name(pdev));
+ err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
+ } else if (!(err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32)))) {
+ using_dac = 0;
+ err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+ }
+
+ if (err) {
+ dev_err(&pdev->dev, "no usable DMA configuration\n");
goto err_out_free_regions;
}
#ifdef __BIG_ENDIAN
- /* byte swap decriptors in hardware */
+ /* byte swap descriptors in hardware */
{
u32 reg;
#endif
err = -ENOMEM;
- hw = kmalloc(sizeof(*hw), GFP_KERNEL);
+ hw = kzalloc(sizeof(*hw), GFP_KERNEL);
if (!hw) {
- printk(KERN_ERR PFX "%s: cannot allocate hardware struct\n",
- pci_name(pdev));
+ dev_err(&pdev->dev, "cannot allocate hardware struct\n");
goto err_out_free_regions;
}
- memset(hw, 0, sizeof(*hw));
hw->pdev = pdev;
+ spin_lock_init(&hw->hw_lock);
spin_lock_init(&hw->phy_lock);
- tasklet_init(&hw->ext_tasklet, skge_extirq, (unsigned long) hw);
+ tasklet_init(&hw->phy_task, &skge_extirq, (unsigned long) hw);
hw->regs = ioremap_nocache(pci_resource_start(pdev, 0), 0x4000);
if (!hw->regs) {
- printk(KERN_ERR PFX "%s: cannot map device registers\n",
- pci_name(pdev));
+ dev_err(&pdev->dev, "cannot map device registers\n");
goto err_out_free_hw;
}
- if ((err = request_irq(pdev->irq, skge_intr, SA_SHIRQ, DRV_NAME, hw))) {
- printk(KERN_ERR PFX "%s: cannot assign irq %d\n",
- pci_name(pdev), pdev->irq);
- goto err_out_iounmap;
- }
- pci_set_drvdata(pdev, hw);
-
err = skge_reset(hw);
if (err)
- goto err_out_free_irq;
+ goto err_out_iounmap;
- printk(KERN_INFO PFX "addr 0x%lx irq %d chip %s rev %d\n",
- pci_resource_start(pdev, 0), pdev->irq,
+ printk(KERN_INFO PFX DRV_VERSION " addr 0x%llx irq %d chip %s rev %d\n",
+ (unsigned long long)pci_resource_start(pdev, 0), pdev->irq,
skge_board_name(hw), hw->chip_rev);
- if ((dev = skge_devinit(hw, 0, using_dac)) == NULL)
+ dev = skge_devinit(hw, 0, using_dac);
+ if (!dev)
goto err_out_led_off;
- if ((err = register_netdev(dev))) {
- printk(KERN_ERR PFX "%s: cannot register net device\n",
- pci_name(pdev));
+ /* Some motherboards are broken and has zero in ROM. */
+ if (!is_valid_ether_addr(dev->dev_addr))
+ dev_warn(&pdev->dev, "bad (zero?) ethernet address in rom\n");
+
+ err = register_netdev(dev);
+ if (err) {
+ dev_err(&pdev->dev, "cannot register net device\n");
goto err_out_free_netdev;
}
+ err = request_irq(pdev->irq, skge_intr, IRQF_SHARED, dev->name, hw);
+ if (err) {
+ dev_err(&pdev->dev, "%s: cannot assign irq %d\n",
+ dev->name, pdev->irq);
+ goto err_out_unregister;
+ }
skge_show_addr(dev);
if (hw->ports > 1 && (dev1 = skge_devinit(hw, 1, using_dac))) {
skge_show_addr(dev1);
else {
/* Failure to register second port need not be fatal */
- printk(KERN_WARNING PFX "register of second port failed\n");
+ dev_warn(&pdev->dev, "register of second port failed\n");
hw->dev[1] = NULL;
free_netdev(dev1);
}
}
+ pci_set_drvdata(pdev, hw);
return 0;
+err_out_unregister:
+ unregister_netdev(dev);
err_out_free_netdev:
free_netdev(dev);
err_out_led_off:
skge_write16(hw, B0_LED, LED_STAT_OFF);
-err_out_free_irq:
- free_irq(pdev->irq, hw);
err_out_iounmap:
iounmap(hw->regs);
err_out_free_hw:
if (!hw)
return;
+ flush_scheduled_work();
+
if ((dev1 = hw->dev[1]))
unregister_netdev(dev1);
dev0 = hw->dev[0];
unregister_netdev(dev0);
- tasklet_kill(&hw->ext_tasklet);
+ tasklet_disable(&hw->phy_task);
+
+ spin_lock_irq(&hw->hw_lock);
+ hw->intr_mask = 0;
+ skge_write32(hw, B0_IMSK, 0);
+ skge_read32(hw, B0_IMSK);
+ spin_unlock_irq(&hw->hw_lock);
+
+ skge_write16(hw, B0_LED, LED_STAT_OFF);
+ skge_write8(hw, B0_CTST, CS_RST_SET);
free_irq(pdev->irq, hw);
pci_release_regions(pdev);
if (dev1)
free_netdev(dev1);
free_netdev(dev0);
- skge_write16(hw, B0_LED, LED_STAT_OFF);
+
iounmap(hw->regs);
kfree(hw);
pci_set_drvdata(pdev, NULL);
}
#ifdef CONFIG_PM
-static int skge_suspend(struct pci_dev *pdev, u32 state)
+static int skge_suspend(struct pci_dev *pdev, pm_message_t state)
{
struct skge_hw *hw = pci_get_drvdata(pdev);
- int i, wol = 0;
+ int i, err, wol = 0;
+
+ if (!hw)
+ return 0;
+
+ err = pci_save_state(pdev);
+ if (err)
+ return err;
- for (i = 0; i < 2; i++) {
+ for (i = 0; i < hw->ports; i++) {
struct net_device *dev = hw->dev[i];
+ struct skge_port *skge = netdev_priv(dev);
- if (dev) {
- struct skge_port *skge = netdev_priv(dev);
- if (netif_running(dev)) {
- netif_carrier_off(dev);
- skge_down(dev);
- }
- netif_device_detach(dev);
- wol |= skge->wol;
- }
+ if (netif_running(dev))
+ skge_down(dev);
+ if (skge->wol)
+ skge_wol_init(skge);
+
+ wol |= skge->wol;
}
- pci_save_state(pdev);
- pci_enable_wake(pdev, state, wol);
- pci_disable_device(pdev);
- pci_set_power_state(pdev, pci_choose_state(pdev, state));
+ skge_write32(hw, B0_IMSK, 0);
+
+ pci_prepare_to_sleep(pdev);
return 0;
}
static int skge_resume(struct pci_dev *pdev)
{
struct skge_hw *hw = pci_get_drvdata(pdev);
- int i;
+ int i, err;
+
+ if (!hw)
+ return 0;
- pci_set_power_state(pdev, PCI_D0);
- pci_restore_state(pdev);
- pci_enable_wake(pdev, PCI_D0, 0);
+ err = pci_back_from_sleep(pdev);
+ if (err)
+ goto out;
+
+ err = pci_restore_state(pdev);
+ if (err)
+ goto out;
- skge_reset(hw);
+ err = skge_reset(hw);
+ if (err)
+ goto out;
- for (i = 0; i < 2; i++) {
+ for (i = 0; i < hw->ports; i++) {
struct net_device *dev = hw->dev[i];
- if (dev) {
- netif_device_attach(dev);
- if (netif_running(dev))
- skge_up(dev);
+
+ if (netif_running(dev)) {
+ err = skge_up(dev);
+
+ if (err) {
+ printk(KERN_ERR PFX "%s: could not up: %d\n",
+ dev->name, err);
+ dev_close(dev);
+ goto out;
+ }
}
}
- return 0;
+out:
+ return err;
}
#endif
+static void skge_shutdown(struct pci_dev *pdev)
+{
+ struct skge_hw *hw = pci_get_drvdata(pdev);
+ int i, wol = 0;
+
+ if (!hw)
+ return;
+
+ for (i = 0; i < hw->ports; i++) {
+ struct net_device *dev = hw->dev[i];
+ struct skge_port *skge = netdev_priv(dev);
+
+ if (skge->wol)
+ skge_wol_init(skge);
+ wol |= skge->wol;
+ }
+
+ if (pci_enable_wake(pdev, PCI_D3cold, wol))
+ pci_enable_wake(pdev, PCI_D3hot, wol);
+
+ pci_disable_device(pdev);
+ pci_set_power_state(pdev, PCI_D3hot);
+
+}
+
static struct pci_driver skge_driver = {
.name = DRV_NAME,
.id_table = skge_id_table,
.suspend = skge_suspend,
.resume = skge_resume,
#endif
+ .shutdown = skge_shutdown,
};
static int __init skge_init_module(void)
{
- return pci_module_init(&skge_driver);
+ skge_debug_init();
+ return pci_register_driver(&skge_driver);
}
static void __exit skge_cleanup_module(void)
{
pci_unregister_driver(&skge_driver);
+ skge_debug_cleanup();
}
module_init(skge_init_module);
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff