#include <linux/interrupt.h>
#include <linux/ioport.h>
#include <linux/in.h>
-#include <linux/slab.h>
#include <linux/string.h>
#include <linux/init.h>
#include <linux/delay.h>
static int seeq8005_probe1(struct net_device *dev, int ioaddr);
static int seeq8005_open(struct net_device *dev);
static void seeq8005_timeout(struct net_device *dev);
-static int seeq8005_send_packet(struct sk_buff *skb, struct net_device *dev);
+static netdev_tx_t seeq8005_send_packet(struct sk_buff *skb,
+ struct net_device *dev);
static irqreturn_t seeq8005_interrupt(int irq, void *dev_id);
static void seeq8005_rx(struct net_device *dev);
static int seeq8005_close(struct net_device *dev);
return ERR_PTR(err);
}
+static const struct net_device_ops seeq8005_netdev_ops = {
+ .ndo_open = seeq8005_open,
+ .ndo_stop = seeq8005_close,
+ .ndo_start_xmit = seeq8005_send_packet,
+ .ndo_tx_timeout = seeq8005_timeout,
+ .ndo_set_multicast_list = set_multicast_list,
+ .ndo_change_mtu = eth_change_mtu,
+ .ndo_set_mac_address = eth_mac_addr,
+ .ndo_validate_addr = eth_validate_addr,
+};
+
/* This is the real probe routine. Linux has a history of friendly device
probes on the ISA bus. A good device probes avoids doing writes, and
verifies that the correct device exists and functions. */
int old_dmaar;
int old_rear;
int retval;
- DECLARE_MAC_BUF(mac);
if (!request_region(ioaddr, SEEQ8005_IO_EXTENT, "seeq8005"))
return -ENODEV;
/* Retrieve and print the ethernet address. */
for (i = 0; i < 6; i++)
dev->dev_addr[i] = SA_prom[i+6];
- printk("%s", print_mac(mac, dev->dev_addr));
+ printk("%pM", dev->dev_addr);
if (dev->irq == 0xff)
; /* Do nothing: a user-level program will set it. */
#if 0
{
- int irqval = request_irq(dev->irq, &seeq8005_interrupt, 0, "seeq8005", dev);
+ int irqval = request_irq(dev->irq, seeq8005_interrupt, 0, "seeq8005", dev);
if (irqval) {
printk ("%s: unable to get IRQ %d (irqval=%d).\n", dev->name,
dev->irq, irqval);
}
}
#endif
- dev->open = seeq8005_open;
- dev->stop = seeq8005_close;
- dev->hard_start_xmit = seeq8005_send_packet;
- dev->tx_timeout = seeq8005_timeout;
+ dev->netdev_ops = &seeq8005_netdev_ops;
dev->watchdog_timeo = HZ/20;
- dev->set_multicast_list = set_multicast_list;
dev->flags &= ~IFF_MULTICAST;
return 0;
struct net_local *lp = netdev_priv(dev);
{
- int irqval = request_irq(dev->irq, &seeq8005_interrupt, 0, "seeq8005", dev);
+ int irqval = request_irq(dev->irq, seeq8005_interrupt, 0, "seeq8005", dev);
if (irqval) {
printk ("%s: unable to get IRQ %d (irqval=%d).\n", dev->name,
dev->irq, irqval);
tx_done(dev) ? "IRQ conflict" : "network cable problem");
/* Try to restart the adaptor. */
seeq8005_init(dev, 1);
- dev->trans_start = jiffies;
+ dev->trans_start = jiffies; /* prevent tx timeout */
netif_wake_queue(dev);
}
-static int seeq8005_send_packet(struct sk_buff *skb, struct net_device *dev)
+static netdev_tx_t seeq8005_send_packet(struct sk_buff *skb,
+ struct net_device *dev)
{
short length = skb->len;
unsigned char *buf;
if (length < ETH_ZLEN) {
if (skb_padto(skb, ETH_ZLEN))
- return 0;
+ return NETDEV_TX_OK;
length = ETH_ZLEN;
}
buf = skb->data;
netif_stop_queue(dev);
hardware_send_packet(dev, buf, length);
- dev->trans_start = jiffies;
dev->stats.tx_bytes += length;
dev_kfree_skb (skb);
/* You might need to clean up and record Tx statistics here. */
- return 0;
+ return NETDEV_TX_OK;
}
/*
skb->protocol=eth_type_trans(skb,dev);
netif_rx(skb);
- dev->last_rx = jiffies;
dev->stats.rx_packets++;
dev->stats.rx_bytes += pkt_len;
}
/* If any worth-while packets have been received, netif_rx()
has done a mark_bh(NET_BH) for us and will work on them
when we get to the bottom-half routine. */
- return;
}
/* The inverse routine to net_open(). */
}
#endif /* MODULE */
-
-/*
- * Local variables:
- * compile-command: "gcc -D__KERNEL__ -I/usr/src/linux/net/inet -Wall -Wstrict-prototypes -O6 -m486 -c skeleton.c"
- * version-control: t
- * kept-new-versions: 5
- * tab-width: 4
- * End:
- */