#include <linux/delay.h>
#include <linux/ethtool.h>
#include <linux/netdevice.h>
-#include <../drivers/net/8390.h>
+#include <linux/log2.h>
+#include "../8390.h"
#include <pcmcia/cs_types.h>
#include <pcmcia/cs.h>
static int pcnet_open(struct net_device *dev);
static int pcnet_close(struct net_device *dev);
static int ei_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
-static struct ethtool_ops netdev_ethtool_ops;
-static irqreturn_t ei_irq_wrapper(int irq, void *dev_id, struct pt_regs *regs);
+static const struct ethtool_ops netdev_ethtool_ops;
+static irqreturn_t ei_irq_wrapper(int irq, void *dev_id);
static void ei_watchdog(u_long arg);
static void pcnet_reset_8390(struct net_device *dev);
static int set_config(struct net_device *dev, struct ifmap *map);
{ /* PCMCIA Technology OEM */ 0x01c8, 0x00, 0xa0, 0x0c, 0 }
};
-#define NR_INFO (sizeof(hw_info)/sizeof(hw_info_t))
+#define NR_INFO ARRAY_SIZE(hw_info)
static hw_info_t default_info = { 0, 0, 0, 0, 0 };
static hw_info_t dl10019_info = { 0, 0, 0, 0, IS_DL10019|HAS_MII };
info->p_dev = link;
link->priv = dev;
- link->irq.Attributes = IRQ_TYPE_EXCLUSIVE;
+ link->irq.Attributes = IRQ_TYPE_DYNAMIC_SHARING;
link->irq.IRQInfo1 = IRQ_LEVEL_ID;
link->conf.Attributes = CONF_ENABLE_IRQ;
link->conf.IntType = INT_MEMORY_AND_IO;
- SET_MODULE_OWNER(dev);
dev->open = &pcnet_open;
dev->stop = &pcnet_close;
dev->set_config = &set_config;
static hw_info_t *get_prom(struct pcmcia_device *link)
{
struct net_device *dev = link->priv;
- kio_addr_t ioaddr = dev->base_addr;
+ unsigned int ioaddr = dev->base_addr;
u_char prom[32];
int i, j;
pcnet_reset_8390(dev);
mdelay(10);
- for (i = 0; i < sizeof(program_seq)/sizeof(program_seq[0]); i++)
+ for (i = 0; i < ARRAY_SIZE(program_seq); i++)
outb_p(program_seq[i].value, ioaddr + program_seq[i].offset);
for (i = 0; i < 32; i++)
static hw_info_t *get_ax88190(struct pcmcia_device *link)
{
struct net_device *dev = link->priv;
- kio_addr_t ioaddr = dev->base_addr;
+ unsigned int ioaddr = dev->base_addr;
int i, j;
/* Not much of a test, but the alternatives are messy */
tuple_t tuple;
cisparse_t parse;
int i, last_ret, last_fn, start_pg, stop_pg, cm_offset;
- int manfid = 0, prodid = 0, has_shmem = 0;
+ int has_shmem = 0;
u_short buf[64];
- hw_info_t *hw_info;
+ hw_info_t *local_hw_info;
+ DECLARE_MAC_BUF(mac);
DEBUG(0, "pcnet_config(0x%p)\n", link);
- tuple.Attributes = 0;
tuple.TupleData = (cisdata_t *)buf;
tuple.TupleDataMax = sizeof(buf);
tuple.TupleOffset = 0;
- tuple.DesiredTuple = CISTPL_CONFIG;
- CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(link, &tuple));
- CS_CHECK(GetTupleData, pcmcia_get_tuple_data(link, &tuple));
- CS_CHECK(ParseTuple, pcmcia_parse_tuple(link, &tuple, &parse));
- link->conf.ConfigBase = parse.config.base;
- link->conf.Present = parse.config.rmask[0];
-
- tuple.DesiredTuple = CISTPL_MANFID;
- tuple.Attributes = TUPLE_RETURN_COMMON;
- if ((pcmcia_get_first_tuple(link, &tuple) == CS_SUCCESS) &&
- (pcmcia_get_tuple_data(link, &tuple) == CS_SUCCESS)) {
- manfid = le16_to_cpu(buf[0]);
- prodid = le16_to_cpu(buf[1]);
- }
-
tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
tuple.Attributes = 0;
CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(link, &tuple));
link->conf.Attributes |= CONF_ENABLE_SPKR;
link->conf.Status = CCSR_AUDIO_ENA;
}
- if ((manfid == MANFID_IBM) &&
- (prodid == PRODID_IBM_HOME_AND_AWAY))
+ if ((link->manf_id == MANFID_IBM) &&
+ (link->card_id == PRODID_IBM_HOME_AND_AWAY))
link->conf.ConfigIndex |= 0x10;
CS_CHECK(RequestConfiguration, pcmcia_request_configuration(link, &link->conf));
dev->if_port = 0;
}
- hw_info = get_hwinfo(link);
- if (hw_info == NULL)
- hw_info = get_prom(link);
- if (hw_info == NULL)
- hw_info = get_dl10019(link);
- if (hw_info == NULL)
- hw_info = get_ax88190(link);
- if (hw_info == NULL)
- hw_info = get_hwired(link);
-
- if (hw_info == NULL) {
+ if ((link->conf.ConfigBase == 0x03c0)
+ && (link->manf_id == 0x149) && (link->card_id = 0xc1ab)) {
+ printk(KERN_INFO "pcnet_cs: this is an AX88190 card!\n");
+ printk(KERN_INFO "pcnet_cs: use axnet_cs instead.\n");
+ goto failed;
+ }
+
+ local_hw_info = get_hwinfo(link);
+ if (local_hw_info == NULL)
+ local_hw_info = get_prom(link);
+ if (local_hw_info == NULL)
+ local_hw_info = get_dl10019(link);
+ if (local_hw_info == NULL)
+ local_hw_info = get_ax88190(link);
+ if (local_hw_info == NULL)
+ local_hw_info = get_hwired(link);
+
+ if (local_hw_info == NULL) {
printk(KERN_NOTICE "pcnet_cs: unable to read hardware net"
" address for io base %#3lx\n", dev->base_addr);
goto failed;
}
- info->flags = hw_info->flags;
+ info->flags = local_hw_info->flags;
/* Check for user overrides */
info->flags |= (delay_output) ? DELAY_OUTPUT : 0;
- if ((manfid == MANFID_SOCKET) &&
- ((prodid == PRODID_SOCKET_LPE) ||
- (prodid == PRODID_SOCKET_LPE_CF) ||
- (prodid == PRODID_SOCKET_EIO)))
+ if ((link->manf_id == MANFID_SOCKET) &&
+ ((link->card_id == PRODID_SOCKET_LPE) ||
+ (link->card_id == PRODID_SOCKET_LPE_CF) ||
+ (link->card_id == PRODID_SOCKET_EIO)))
info->flags &= ~USE_BIG_BUF;
if (!use_big_buf)
info->flags &= ~USE_BIG_BUF;
SET_ETHTOOL_OPS(dev, &netdev_ethtool_ops);
if (info->flags & (IS_DL10019|IS_DL10022)) {
- u_char id = inb(dev->base_addr + 0x1a);
dev->do_ioctl = &ei_ioctl;
mii_phy_probe(dev);
- if ((id == 0x30) && !info->pna_phy && (info->eth_phy == 4))
- info->eth_phy = 0;
}
link->dev_node = &info->node;
printk (" mem %#5lx,", dev->mem_start);
if (info->flags & HAS_MISC_REG)
printk(" %s xcvr,", if_names[dev->if_port]);
- printk(" hw_addr ");
- for (i = 0; i < 6; i++)
- printk("%02X%s", dev->dev_addr[i], ((i<5) ? ":" : "\n"));
+ printk(" hw_addr %s\n", print_mac(mac, dev->dev_addr));
return 0;
cs_failed:
#define MDIO_DATA_READ 0x10
#define MDIO_MASK 0x0f
-static void mdio_sync(kio_addr_t addr)
+static void mdio_sync(unsigned int addr)
{
int bits, mask = inb(addr) & MDIO_MASK;
for (bits = 0; bits < 32; bits++) {
}
}
-static int mdio_read(kio_addr_t addr, int phy_id, int loc)
+static int mdio_read(unsigned int addr, int phy_id, int loc)
{
u_int cmd = (0x06<<10)|(phy_id<<5)|loc;
int i, retval = 0, mask = inb(addr) & MDIO_MASK;
return (retval>>1) & 0xffff;
}
-static void mdio_write(kio_addr_t addr, int phy_id, int loc, int value)
+static void mdio_write(unsigned int addr, int phy_id, int loc, int value)
{
u_int cmd = (0x05<<28)|(phy_id<<23)|(loc<<18)|(1<<17)|value;
int i, mask = inb(addr) & MDIO_MASK;
}
}
-static void mdio_reset(kio_addr_t addr, int phy_id)
-{
- outb_p(0x08, addr);
- outb_p(0x0c, addr);
- outb_p(0x08, addr);
- outb_p(0x0c, addr);
- outb_p(0x00, addr);
-}
-
/*======================================================================
EEPROM access routines for DL10019 and DL10022 based cards
#define DL19FDUPLX 0x0400 /* DL10019 Full duplex mode */
-static int read_eeprom(kio_addr_t ioaddr, int location)
+static int read_eeprom(unsigned int ioaddr, int location)
{
int i, retval = 0;
- kio_addr_t ee_addr = ioaddr + DLINK_EEPROM;
+ unsigned int ee_addr = ioaddr + DLINK_EEPROM;
int read_cmd = location | (EE_READ_CMD << 8);
outb(0, ee_addr);
In ASIC mode, EE_ADOT is used to output the data to the ASIC.
*/
-static void write_asic(kio_addr_t ioaddr, int location, short asic_data)
+static void write_asic(unsigned int ioaddr, int location, short asic_data)
{
int i;
- kio_addr_t ee_addr = ioaddr + DLINK_EEPROM;
+ unsigned int ee_addr = ioaddr + DLINK_EEPROM;
short dataval;
int read_cmd = location | (EE_READ_CMD << 8);
static void set_misc_reg(struct net_device *dev)
{
- kio_addr_t nic_base = dev->base_addr;
+ unsigned int nic_base = dev->base_addr;
pcnet_dev_t *info = PRIV(dev);
u_char tmp;
}
if (info->flags & IS_DL10022) {
if (info->flags & HAS_MII) {
- mdio_reset(nic_base + DLINK_GPIO, info->eth_phy);
+ /* Advertise 100F, 100H, 10F, 10H */
+ mdio_write(nic_base + DLINK_GPIO, info->eth_phy, 4, 0x01e1);
/* Restart MII autonegotiation */
mdio_write(nic_base + DLINK_GPIO, info->eth_phy, 0, 0x0000);
mdio_write(nic_base + DLINK_GPIO, info->eth_phy, 0, 0x1200);
static void mii_phy_probe(struct net_device *dev)
{
pcnet_dev_t *info = PRIV(dev);
- kio_addr_t mii_addr = dev->base_addr + DLINK_GPIO;
+ unsigned int mii_addr = dev->base_addr + DLINK_GPIO;
int i;
u_int tmp, phyid;
static int pcnet_open(struct net_device *dev)
{
+ int ret;
pcnet_dev_t *info = PRIV(dev);
struct pcmcia_device *link = info->p_dev;
+ unsigned int nic_base = dev->base_addr;
DEBUG(2, "pcnet_open('%s')\n", dev->name);
if (!pcmcia_dev_present(link))
return -ENODEV;
- link->open++;
-
set_misc_reg(dev);
- request_irq(dev->irq, ei_irq_wrapper, SA_SHIRQ, dev_info, dev);
+
+ outb_p(0xFF, nic_base + EN0_ISR); /* Clear bogus intr. */
+ ret = request_irq(dev->irq, ei_irq_wrapper, IRQF_SHARED, dev_info, dev);
+ if (ret)
+ return ret;
+
+ link->open++;
info->phy_id = info->eth_phy;
info->link_status = 0x00;
static void pcnet_reset_8390(struct net_device *dev)
{
- kio_addr_t nic_base = dev->base_addr;
+ unsigned int nic_base = dev->base_addr;
int i;
ei_status.txing = ei_status.dmaing = 0;
/*====================================================================*/
-static irqreturn_t ei_irq_wrapper(int irq, void *dev_id, struct pt_regs *regs)
+static irqreturn_t ei_irq_wrapper(int irq, void *dev_id)
{
struct net_device *dev = dev_id;
pcnet_dev_t *info;
- irqreturn_t ret = ei_interrupt(irq, dev_id, regs);
+ irqreturn_t ret = ei_interrupt(irq, dev_id);
if (ret == IRQ_HANDLED) {
info = PRIV(dev);
{
struct net_device *dev = (struct net_device *)arg;
pcnet_dev_t *info = PRIV(dev);
- kio_addr_t nic_base = dev->base_addr;
- kio_addr_t mii_addr = nic_base + DLINK_GPIO;
+ unsigned int nic_base = dev->base_addr;
+ unsigned int mii_addr = nic_base + DLINK_GPIO;
u_short link;
if (!netif_device_present(dev)) goto reschedule;
/* Check for pending interrupt with expired latency timer: with
this, we can limp along even if the interrupt is blocked */
- outb_p(E8390_NODMA+E8390_PAGE0, nic_base + E8390_CMD);
if (info->stale++ && (inb_p(nic_base + EN0_ISR) & ENISR_ALL)) {
if (!info->fast_poll)
printk(KERN_INFO "%s: interrupt(s) dropped!\n", dev->name);
- ei_irq_wrapper(dev->irq, dev, NULL);
+ ei_irq_wrapper(dev->irq, dev);
info->fast_poll = HZ;
}
if (info->fast_poll) {
strcpy(info->driver, "pcnet_cs");
}
-static struct ethtool_ops netdev_ethtool_ops = {
+static const struct ethtool_ops netdev_ethtool_ops = {
.get_drvinfo = netdev_get_drvinfo,
};
{
pcnet_dev_t *info = PRIV(dev);
u16 *data = (u16 *)&rq->ifr_ifru;
- kio_addr_t mii_addr = dev->base_addr + DLINK_GPIO;
+ unsigned int mii_addr = dev->base_addr + DLINK_GPIO;
switch (cmd) {
case SIOCGMIIPHY:
data[0] = info->phy_id;
struct e8390_pkt_hdr *hdr,
int ring_page)
{
- kio_addr_t nic_base = dev->base_addr;
+ unsigned int nic_base = dev->base_addr;
if (ei_status.dmaing) {
printk(KERN_NOTICE "%s: DMAing conflict in dma_block_input."
static void dma_block_input(struct net_device *dev, int count,
struct sk_buff *skb, int ring_offset)
{
- kio_addr_t nic_base = dev->base_addr;
+ unsigned int nic_base = dev->base_addr;
int xfer_count = count;
char *buf = skb->data;
static void dma_block_output(struct net_device *dev, int count,
const u_char *buf, const int start_page)
{
- kio_addr_t nic_base = dev->base_addr;
+ unsigned int nic_base = dev->base_addr;
pcnet_dev_t *info = PRIV(dev);
#ifdef PCMCIA_DEBUG
int retries = 0;
window_size = 32 * 1024;
/* Make sure it's a power of two. */
- while ((window_size & (window_size - 1)) != 0)
- window_size += window_size & ~(window_size - 1);
+ window_size = roundup_pow_of_two(window_size);
/* Allocate a memory window */
req.Attributes = WIN_DATA_WIDTH_16|WIN_MEMORY_TYPE_CM|WIN_ENABLE;
PCMCIA_PFC_DEVICE_PROD_ID12(0, "Grey Cell", "GCS3000", 0x2a151fac, 0x48b932ae),
PCMCIA_PFC_DEVICE_PROD_ID12(0, "Linksys", "EtherFast 10&100 + 56K PC Card (PCMLM56)", 0x0733cc81, 0xb3765033),
PCMCIA_PFC_DEVICE_PROD_ID12(0, "LINKSYS", "PCMLM336", 0xf7cb0b07, 0x7a821b58),
+ PCMCIA_PFC_DEVICE_PROD_ID12(0, "MICRO RESEARCH", "COMBO-L/M-336", 0xb2ced065, 0x3ced0555),
PCMCIA_PFC_DEVICE_PROD_ID12(0, "PCMCIAs", "ComboCard", 0xdcfe12d3, 0xcd8906cc),
PCMCIA_PFC_DEVICE_PROD_ID12(0, "PCMCIAs", "LanModem", 0xdcfe12d3, 0xc67c648f),
PCMCIA_MFC_DEVICE_PROD_ID12(0, "IBM", "Home and Away 28.8 PC Card ", 0xb569a6e5, 0x5bd4ff2c),
PCMCIA_DEVICE_MANF_CARD(0x0104, 0x0145),
PCMCIA_DEVICE_MANF_CARD(0x0149, 0x0230),
PCMCIA_DEVICE_MANF_CARD(0x0149, 0x4530),
-/* PCMCIA_DEVICE_MANF_CARD(0x0149, 0xc1ab), conflict with axnet_cs */
+ PCMCIA_DEVICE_MANF_CARD(0x0149, 0xc1ab),
PCMCIA_DEVICE_MANF_CARD(0x0186, 0x0110),
PCMCIA_DEVICE_MANF_CARD(0x01bf, 0x2328),
PCMCIA_DEVICE_MANF_CARD(0x01bf, 0x8041),
PCMCIA_DEVICE_MANF_CARD(0x0213, 0x2452),
-/* PCMCIA_DEVICE_MANF_CARD(0x021b, 0x0202), conflict with axnet_cs */
PCMCIA_DEVICE_MANF_CARD(0x026f, 0x0300),
PCMCIA_DEVICE_MANF_CARD(0x026f, 0x0307),
PCMCIA_DEVICE_MANF_CARD(0x026f, 0x030a),
PCMCIA_DEVICE_MANF_CARD(0x0274, 0x1103),
PCMCIA_DEVICE_MANF_CARD(0x0274, 0x1121),
PCMCIA_DEVICE_PROD_ID12("2408LAN", "Ethernet", 0x352fff7f, 0x00b2e941),
+ PCMCIA_DEVICE_PROD_ID1234("Socket", "CF 10/100 Ethernet Card", "Revision B", "05/11/06", 0xb38bcc2e, 0x4de88352, 0xeaca6c8d, 0x7e57c22e),
PCMCIA_DEVICE_PROD_ID123("Cardwell", "PCMCIA", "ETHERNET", 0x9533672e, 0x281f1c5d, 0x3ff7175b),
PCMCIA_DEVICE_PROD_ID123("CNet ", "CN30BC", "ETHERNET", 0x9fe55d3d, 0x85601198, 0x3ff7175b),
PCMCIA_DEVICE_PROD_ID123("Digital", "Ethernet", "Adapter", 0x9999ab35, 0x00b2e941, 0x4b0d829e),
PCMCIA_DEVICE_PROD_ID12("corega K.K.", "corega EtherII PCC-TD", 0x5261440f, 0xc49bd73d),
PCMCIA_DEVICE_PROD_ID12("Corega K.K.", "corega EtherII PCC-TD", 0xd4fdcbd8, 0xc49bd73d),
PCMCIA_DEVICE_PROD_ID12("corega K.K.", "corega Ether PCC-T", 0x5261440f, 0x6705fcaa),
+ PCMCIA_DEVICE_PROD_ID12("corega K.K.", "corega Ether PCC-TD", 0x5261440f, 0x47d5ca83),
PCMCIA_DEVICE_PROD_ID12("corega K.K.", "corega FastEther PCC-TX", 0x5261440f, 0x485e85d9),
PCMCIA_DEVICE_PROD_ID12("Corega,K.K.", "Ethernet LAN Card", 0x110d26d9, 0x9fd2f0a2),
PCMCIA_DEVICE_PROD_ID12("corega,K.K.", "Ethernet LAN Card", 0x9791a90e, 0x9fd2f0a2),
+ PCMCIA_DEVICE_PROD_ID12("corega K.K.", "(CG-LAPCCTXD)", 0x5261440f, 0x73ec0d88),
PCMCIA_DEVICE_PROD_ID12("CouplerlessPCMCIA", "100BASE", 0xee5af0ad, 0x7c2add04),
PCMCIA_DEVICE_PROD_ID12("CyQ've", "ELA-010", 0x77008979, 0x9d8d445d),
PCMCIA_DEVICE_PROD_ID12("CyQ've", "ELA-110E 10/100M LAN Card", 0x77008979, 0xfd184814),
PCMCIA_DEVICE_PROD_ID12("Laneed", "LD-CDF", 0x1b7827b2, 0xfec71e40),
PCMCIA_DEVICE_PROD_ID12("Laneed", "LD-CDL/T", 0x1b7827b2, 0x79fba4f7),
PCMCIA_DEVICE_PROD_ID12("Laneed", "LD-CDS", 0x1b7827b2, 0x931afaab),
+ PCMCIA_DEVICE_PROD_ID12("LEMEL", "LM-N89TX PRO", 0xbbefb52f, 0xd2897a97),
PCMCIA_DEVICE_PROD_ID12("Linksys", "Combo PCMCIA EthernetCard (EC2T)", 0x0733cc81, 0x32ee8c78),
PCMCIA_DEVICE_PROD_ID12("LINKSYS", "E-CARD", 0xf7cb0b07, 0x6701da11),
PCMCIA_DEVICE_PROD_ID12("Linksys", "EtherFast 10/100 Integrated PC Card (PCM100)", 0x0733cc81, 0x453c3f9d),
PCMCIA_DEVICE_PROD_ID12("Logitec", "LPM-LN100TX", 0x88fcdeda, 0x6d772737),
PCMCIA_DEVICE_PROD_ID12("Logitec", "LPM-LN100TE", 0x88fcdeda, 0x0e714bee),
PCMCIA_DEVICE_PROD_ID12("Logitec", "LPM-LN20T", 0x88fcdeda, 0x81090922),
+ PCMCIA_DEVICE_PROD_ID12("Logitec", "LPM-LN10TE", 0x88fcdeda, 0xc1e2521c),
PCMCIA_DEVICE_PROD_ID12("LONGSHINE", "PCMCIA Ethernet Card", 0xf866b0b0, 0x6f6652e0),
PCMCIA_DEVICE_PROD_ID12("MACNICA", "ME1-JEIDA", 0x20841b68, 0xaf8a3578),
PCMCIA_DEVICE_PROD_ID12("Macsense", "MPC-10", 0xd830297f, 0xd265c307),
PCMCIA_DEVICE_PROD_ID1("CyQ've 10 Base-T LAN CARD", 0x94faf360),
PCMCIA_DEVICE_PROD_ID1("EP-210 PCMCIA LAN CARD.", 0x8850b4de),
PCMCIA_DEVICE_PROD_ID1("ETHER-C16", 0x06a8514f),
- PCMCIA_DEVICE_PROD_ID1("IC-CARD", 0x60cb09a6),
PCMCIA_DEVICE_PROD_ID1("NE2000 Compatible", 0x75b8ad5a),
PCMCIA_DEVICE_PROD_ID2("EN-6200P2", 0xa996d078),
/* too generic! */
PCMCIA_DEVICE_CIS_PROD_ID12("NDC", "Ethernet", 0x01c43ae1, 0x00b2e941, "NE2K.cis"),
PCMCIA_DEVICE_CIS_PROD_ID12("PMX ", "PE-200", 0x34f3f1c8, 0x10b59f8c, "PE-200.cis"),
PCMCIA_DEVICE_CIS_PROD_ID12("TAMARACK", "Ethernet", 0xcf434fba, 0x00b2e941, "tamarack.cis"),
+ PCMCIA_DEVICE_PROD_ID12("Ethernet", "CF Size PC Card", 0x00b2e941, 0x43ac239b),
PCMCIA_DEVICE_PROD_ID123("Fast Ethernet", "CF Size PC Card", "1.0",
0xb4be14e3, 0x43ac239b, 0x0877b627),
PCMCIA_DEVICE_NULL
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff