Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394...
[safe/jmp/linux-2.6] / drivers / net / ne.c
index 874d291..b8e2923 100644 (file)
@@ -64,6 +64,25 @@ static const char version2[] =
 
 /* Do we support clones that don't adhere to 14,15 of the SAprom ? */
 #define SUPPORT_NE_BAD_CLONES
+/* 0xbad = bad sig or no reset ack */
+#define BAD 0xbad
+
+#define MAX_NE_CARDS   4       /* Max number of NE cards per module */
+static struct platform_device *pdev_ne[MAX_NE_CARDS];
+static int io[MAX_NE_CARDS];
+static int irq[MAX_NE_CARDS];
+static int bad[MAX_NE_CARDS];
+
+#ifdef MODULE
+module_param_array(io, int, NULL, 0);
+module_param_array(irq, int, NULL, 0);
+module_param_array(bad, int, NULL, 0);
+MODULE_PARM_DESC(io, "I/O base address(es),required");
+MODULE_PARM_DESC(irq, "IRQ number(s)");
+MODULE_PARM_DESC(bad, "Accept card(s) with bad signatures");
+MODULE_DESCRIPTION("NE1000/NE2000 ISA/PnP Ethernet driver");
+MODULE_LICENSE("GPL");
+#endif /* MODULE */
 
 /* Do we perform extra sanity checks on stuff ? */
 /* #define NE_SANITY_CHECK */
@@ -74,6 +93,10 @@ static const char version2[] =
 /* Do we have a non std. amount of memory? (in units of 256 byte pages) */
 /* #define PACKETBUF_MEMSIZE   0x40 */
 
+/* This is set up so that no ISA autoprobe takes place. We can't guarantee
+that the ne2k probe is the last 8390 based probe to take place (as it
+is at boot) and so the probe will get confused by any other 8390 cards.
+ISA device autoprobes on a running machine are not recommended anyway. */
 #if !defined(MODULE) && (defined(CONFIG_ISA) || defined(CONFIG_M32R))
 /* Do we need a portlist for the ISA auto-probe ? */
 #define NEEDS_PORTLIST
@@ -118,8 +141,8 @@ bad_clone_list[] __initdata = {
     {"E-LAN100", "E-LAN200", {0x00, 0x00, 0x5d}}, /* Broken ne1000 clones */
     {"PCM-4823", "PCM-4823", {0x00, 0xc0, 0x6c}}, /* Broken Advantech MoBo */
     {"REALTEK", "RTL8019", {0x00, 0x00, 0xe8}}, /* no-name with Realtek chip */
-#if defined(CONFIG_TOSHIBA_RBTX4927) || defined(CONFIG_TOSHIBA_RBTX4938)
-    {"RBHMA4X00-RTL8019", "RBHMA4X00/RTL8019", {0x00, 0x60, 0x0a}},  /* Toshiba built-in */
+#ifdef CONFIG_MACH_TX49XX
+    {"RBHMA4X00-RTL8019", "RBHMA4X00-RTL8019", {0x00, 0x60, 0x0a}},  /* Toshiba built-in */
 #endif
     {"LCS-8834", "LCS-8836", {0x04, 0x04, 0x37}}, /* ShinyNet (SET) */
     {NULL,}
@@ -142,7 +165,7 @@ bad_clone_list[] __initdata = {
 #if defined(CONFIG_PLAT_MAPPI)
 #  define DCR_VAL 0x4b
 #elif defined(CONFIG_PLAT_OAKS32R)  || \
-   defined(CONFIG_TOSHIBA_RBTX4927) || defined(CONFIG_TOSHIBA_RBTX4938)
+   defined(CONFIG_MACH_TX49XX)
 #  define DCR_VAL 0x48         /* 8-bit mode */
 #else
 #  define DCR_VAL 0x49
@@ -151,9 +174,6 @@ bad_clone_list[] __initdata = {
 static int ne_probe1(struct net_device *dev, unsigned long ioaddr);
 static int ne_probe_isapnp(struct net_device *dev);
 
-static int ne_open(struct net_device *dev);
-static int ne_close(struct net_device *dev);
-
 static void ne_reset_8390(struct net_device *dev);
 static void ne_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr,
                          int ring_page);
@@ -192,8 +212,13 @@ static int __init do_ne_probe(struct net_device *dev)
 #endif
 
        /* First check any supplied i/o locations. User knows best. <cough> */
-       if (base_addr > 0x1ff)  /* Check a single specified location. */
-               return ne_probe1(dev, base_addr);
+       if (base_addr > 0x1ff) {        /* Check a single specified location. */
+               int ret = ne_probe1(dev, base_addr);
+               if (ret)
+                       printk(KERN_WARNING "ne.c: No NE*000 card found at "
+                               "i/o = %#lx\n", base_addr);
+               return ret;
+       }
        else if (base_addr != 0)        /* Don't probe at all. */
                return -ENXIO;
 
@@ -214,28 +239,6 @@ static int __init do_ne_probe(struct net_device *dev)
        return -ENODEV;
 }
 
-#ifndef MODULE
-struct net_device * __init ne_probe(int unit)
-{
-       struct net_device *dev = alloc_ei_netdev();
-       int err;
-
-       if (!dev)
-               return ERR_PTR(-ENOMEM);
-
-       sprintf(dev->name, "eth%d", unit);
-       netdev_boot_setup_check(dev);
-
-       err = do_ne_probe(dev);
-       if (err)
-               goto out;
-       return dev;
-out:
-       free_netdev(dev);
-       return ERR_PTR(err);
-}
-#endif
-
 static int __init ne_probe_isapnp(struct net_device *dev)
 {
        int i;
@@ -291,7 +294,6 @@ static int __init ne_probe1(struct net_device *dev, unsigned long ioaddr)
        int neX000, ctron, copam, bad_card;
        int reg0, ret;
        static unsigned version_printed;
-       DECLARE_MAC_BUF(mac);
 
        if (!request_region(ioaddr, NE_IO_EXTENT, DRV_NAME))
                return -EBUSY;
@@ -319,7 +321,7 @@ static int __init ne_probe1(struct net_device *dev, unsigned long ioaddr)
        }
 
        if (ei_debug  &&  version_printed++ == 0)
-               printk(KERN_INFO "%s" KERN_INFO "%s", version1, version2);
+               printk(KERN_INFO "%s%s", version1, version2);
 
        printk(KERN_INFO "NE*000 ethercard probe at %#3lx:", ioaddr);
 
@@ -329,7 +331,7 @@ static int __init ne_probe1(struct net_device *dev, unsigned long ioaddr)
           with an otherwise unused dev->mem_end value of "0xBAD" will
           cause the driver to skip these parts of the probe. */
 
-       bad_card = ((dev->base_addr != 0) && (dev->mem_end == 0xbad));
+       bad_card = ((dev->base_addr != 0) && (dev->mem_end == BAD));
 
        /* Reset card. Who knows what dain-bramaged state it was left in. */
 
@@ -355,7 +357,7 @@ static int __init ne_probe1(struct net_device *dev, unsigned long ioaddr)
        }
 
        /* Read the 16 bytes of station address PROM.
-          We must first initialize registers, similar to NS8390_init(eifdev, 0).
+          We must first initialize registers, similar to NS8390p_init(eifdev, 0).
           We can't reliably read the SAPROM address without this.
           (I learned the hard way!). */
        {
@@ -490,7 +492,7 @@ static int __init ne_probe1(struct net_device *dev, unsigned long ioaddr)
 
        /* Snarf the interrupt now.  There's no point in waiting since we cannot
           share and the board will usually be enabled. */
-       ret = request_irq(dev->irq, ei_interrupt, 0, name, dev);
+       ret = request_irq(dev->irq, eip_interrupt, 0, name, dev);
        if (ret) {
                printk (" unable to get IRQ %d (errno=%d).\n", dev->irq, ret);
                goto err_out;
@@ -511,7 +513,7 @@ static int __init ne_probe1(struct net_device *dev, unsigned long ioaddr)
        }
 #endif
 
-       printk("%s\n", print_mac(mac, dev->dev_addr));
+       printk("%pM\n", dev->dev_addr);
 
        ei_status.name = name;
        ei_status.tx_start_page = start_page;
@@ -531,12 +533,9 @@ static int __init ne_probe1(struct net_device *dev, unsigned long ioaddr)
        ei_status.block_output = &ne_block_output;
        ei_status.get_8390_hdr = &ne_get_8390_hdr;
        ei_status.priv = 0;
-       dev->open = &ne_open;
-       dev->stop = &ne_close;
-#ifdef CONFIG_NET_POLL_CONTROLLER
-       dev->poll_controller = ei_poll;
-#endif
-       NS8390_init(dev, 0);
+
+       dev->netdev_ops = &eip_netdev_ops;
+       NS8390p_init(dev, 0);
 
        ret = register_netdev(dev);
        if (ret)
@@ -552,20 +551,6 @@ err_out:
        return ret;
 }
 
-static int ne_open(struct net_device *dev)
-{
-       ei_open(dev);
-       return 0;
-}
-
-static int ne_close(struct net_device *dev)
-{
-       if (ei_debug > 1)
-               printk(KERN_DEBUG "%s: Shutting down ethercard.\n", dev->name);
-       ei_close(dev);
-       return 0;
-}
-
 /* Hard reset the card.  This used to pause for the same period that a
    8390 reset command required, but that shouldn't be necessary. */
 
@@ -794,58 +779,106 @@ retry:
                if (time_after(jiffies, dma_start + 2*HZ/100)) {                /* 20ms */
                        printk(KERN_WARNING "%s: timeout waiting for Tx RDC.\n", dev->name);
                        ne_reset_8390(dev);
-                       NS8390_init(dev,1);
+                       NS8390p_init(dev, 1);
                        break;
                }
 
        outb_p(ENISR_RDC, nic_base + EN0_ISR);  /* Ack intr. */
        ei_status.dmaing &= ~0x01;
-       return;
 }
 
 static int __init ne_drv_probe(struct platform_device *pdev)
 {
        struct net_device *dev;
+       int err, this_dev = pdev->id;
        struct resource *res;
-       int err, irq;
 
-       res = platform_get_resource(pdev, IORESOURCE_IO, 0);
-       irq = platform_get_irq(pdev, 0);
-       if (!res || irq < 0)
-               return -ENODEV;
-
-       dev = alloc_ei_netdev();
+       dev = alloc_eip_netdev();
        if (!dev)
                return -ENOMEM;
-       dev->irq = irq;
-       dev->base_addr = res->start;
+
+       /* ne.c doesn't populate resources in platform_device, but
+        * rbtx4927_ne_init and rbtx4938_ne_init do register devices
+        * with resources.
+        */
+       res = platform_get_resource(pdev, IORESOURCE_IO, 0);
+       if (res) {
+               dev->base_addr = res->start;
+               dev->irq = platform_get_irq(pdev, 0);
+       } else {
+               if (this_dev < 0 || this_dev >= MAX_NE_CARDS)
+                       return -EINVAL;
+               dev->base_addr = io[this_dev];
+               dev->irq = irq[this_dev];
+               dev->mem_end = bad[this_dev];
+       }
        err = do_ne_probe(dev);
        if (err) {
                free_netdev(dev);
                return err;
        }
        platform_set_drvdata(pdev, dev);
+
+       /* Update with any values found by probing, don't update if
+        * resources were specified.
+        */
+       if (!res) {
+               io[this_dev] = dev->base_addr;
+               irq[this_dev] = dev->irq;
+       }
        return 0;
 }
 
-static int __exit ne_drv_remove(struct platform_device *pdev)
+static int ne_drv_remove(struct platform_device *pdev)
 {
        struct net_device *dev = platform_get_drvdata(pdev);
 
-       unregister_netdev(dev);
-       free_irq(dev->irq, dev);
-       release_region(dev->base_addr, NE_IO_EXTENT);
-       free_netdev(dev);
+       if (dev) {
+               struct pnp_dev *idev = (struct pnp_dev *)ei_status.priv;
+               netif_device_detach(dev);
+               unregister_netdev(dev);
+               if (idev)
+                       pnp_device_detach(idev);
+               /* Careful ne_drv_remove can be called twice, once from
+                * the platform_driver.remove and again when the
+                * platform_device is being removed.
+                */
+               ei_status.priv = 0;
+               free_irq(dev->irq, dev);
+               release_region(dev->base_addr, NE_IO_EXTENT);
+               free_netdev(dev);
+               platform_set_drvdata(pdev, NULL);
+       }
        return 0;
 }
 
+/* Remove unused devices or all if true. */
+static void ne_loop_rm_unreg(int all)
+{
+       int this_dev;
+       struct platform_device *pdev;
+       for (this_dev = 0; this_dev < MAX_NE_CARDS; this_dev++) {
+               pdev = pdev_ne[this_dev];
+               /* No network device == unused */
+               if (pdev && (!platform_get_drvdata(pdev) || all)) {
+                       ne_drv_remove(pdev);
+                       platform_device_unregister(pdev);
+                       pdev_ne[this_dev] = NULL;
+               }
+       }
+}
+
 #ifdef CONFIG_PM
 static int ne_drv_suspend(struct platform_device *pdev, pm_message_t state)
 {
        struct net_device *dev = platform_get_drvdata(pdev);
 
-       if (netif_running(dev))
+       if (netif_running(dev)) {
+               struct pnp_dev *idev = (struct pnp_dev *)ei_status.priv;
                netif_device_detach(dev);
+               if (idev)
+                       pnp_stop_dev(idev);
+       }
        return 0;
 }
 
@@ -854,8 +887,11 @@ static int ne_drv_resume(struct platform_device *pdev)
        struct net_device *dev = platform_get_drvdata(pdev);
 
        if (netif_running(dev)) {
+               struct pnp_dev *idev = (struct pnp_dev *)ei_status.priv;
+               if (idev)
+                       pnp_start_dev(idev);
                ne_reset_8390(dev);
-               NS8390_init(dev, 1);
+               NS8390p_init(dev, 1);
                netif_device_attach(dev);
        }
        return 0;
@@ -866,7 +902,7 @@ static int ne_drv_resume(struct platform_device *pdev)
 #endif
 
 static struct platform_driver ne_driver = {
-       .remove         = __exit_p(ne_drv_remove),
+       .remove         = ne_drv_remove,
        .suspend        = ne_drv_suspend,
        .resume         = ne_drv_resume,
        .driver         = {
@@ -875,91 +911,96 @@ static struct platform_driver ne_driver = {
        },
 };
 
-static int __init ne_init(void)
+static void __init ne_add_devices(void)
 {
-       return platform_driver_probe(&ne_driver, ne_drv_probe);
-}
+       int this_dev;
+       struct platform_device *pdev;
 
-static void __exit ne_exit(void)
-{
-       platform_driver_unregister(&ne_driver);
+       for (this_dev = 0; this_dev < MAX_NE_CARDS; this_dev++) {
+               if (pdev_ne[this_dev])
+                       continue;
+               pdev = platform_device_register_simple(
+                       DRV_NAME, this_dev, NULL, 0);
+               if (IS_ERR(pdev))
+                       continue;
+               pdev_ne[this_dev] = pdev;
+       }
 }
 
 #ifdef MODULE
-#define MAX_NE_CARDS   4       /* Max number of NE cards per module */
-static struct net_device *dev_ne[MAX_NE_CARDS];
-static int io[MAX_NE_CARDS];
-static int irq[MAX_NE_CARDS];
-static int bad[MAX_NE_CARDS];  /* 0xbad = bad sig or no reset ack */
-
-module_param_array(io, int, NULL, 0);
-module_param_array(irq, int, NULL, 0);
-module_param_array(bad, int, NULL, 0);
-MODULE_PARM_DESC(io, "I/O base address(es),required");
-MODULE_PARM_DESC(irq, "IRQ number(s)");
-MODULE_PARM_DESC(bad, "Accept card(s) with bad signatures");
-MODULE_DESCRIPTION("NE1000/NE2000 ISA/PnP Ethernet driver");
-MODULE_LICENSE("GPL");
-
-/* This is set up so that no ISA autoprobe takes place. We can't guarantee
-that the ne2k probe is the last 8390 based probe to take place (as it
-is at boot) and so the probe will get confused by any other 8390 cards.
-ISA device autoprobes on a running machine are not recommended anyway. */
-
 int __init init_module(void)
 {
-       int this_dev, found = 0;
-       int plat_found = !ne_init();
-
-       for (this_dev = 0; this_dev < MAX_NE_CARDS; this_dev++) {
-               struct net_device *dev = alloc_ei_netdev();
-               if (!dev)
-                       break;
-               dev->irq = irq[this_dev];
-               dev->mem_end = bad[this_dev];
-               dev->base_addr = io[this_dev];
-               if (do_ne_probe(dev) == 0) {
-                       dev_ne[found++] = dev;
-                       continue;
-               }
-               free_netdev(dev);
-               if (found || plat_found)
-                       break;
-               if (io[this_dev] != 0)
-                       printk(KERN_WARNING "ne.c: No NE*000 card found at i/o = %#x\n", io[this_dev]);
-               else
-                       printk(KERN_NOTICE "ne.c: You must supply \"io=0xNNN\" value(s) for ISA cards.\n");
-               return -ENXIO;
+       int retval;
+       ne_add_devices();
+       retval = platform_driver_probe(&ne_driver, ne_drv_probe);
+       if (retval) {
+               if (io[0] == 0)
+                       printk(KERN_NOTICE "ne.c: You must supply \"io=0xNNN\""
+                               " value(s) for ISA cards.\n");
+               ne_loop_rm_unreg(1);
+               return retval;
        }
-       if (found || plat_found)
-               return 0;
-       return -ENODEV;
-}
 
-static void cleanup_card(struct net_device *dev)
+       /* Unregister unused platform_devices. */
+       ne_loop_rm_unreg(0);
+       return retval;
+}
+#else /* MODULE */
+static int __init ne_init(void)
 {
-       struct pnp_dev *idev = (struct pnp_dev *)ei_status.priv;
-       if (idev)
-               pnp_device_detach(idev);
-       free_irq(dev->irq, dev);
-       release_region(dev->base_addr, NE_IO_EXTENT);
+       int retval = platform_driver_probe(&ne_driver, ne_drv_probe);
+
+       /* Unregister unused platform_devices. */
+       ne_loop_rm_unreg(0);
+       return retval;
 }
+module_init(ne_init);
 
-void __exit cleanup_module(void)
+struct net_device * __init ne_probe(int unit)
 {
        int this_dev;
+       struct net_device *dev;
+
+       /* Find an empty slot, that is no net_device and zero io port. */
+       this_dev = 0;
+       while ((pdev_ne[this_dev] && platform_get_drvdata(pdev_ne[this_dev])) ||
+               io[this_dev]) {
+               if (++this_dev == MAX_NE_CARDS)
+                       return ERR_PTR(-ENOMEM);
+       }
+
+       /* Get irq, io from kernel command line */
+       dev = alloc_eip_netdev();
+       if (!dev)
+               return ERR_PTR(-ENOMEM);
+
+       sprintf(dev->name, "eth%d", unit);
+       netdev_boot_setup_check(dev);
+
+       io[this_dev] = dev->base_addr;
+       irq[this_dev] = dev->irq;
+       bad[this_dev] = dev->mem_end;
 
-       ne_exit();
+       free_netdev(dev);
+
+       ne_add_devices();
+
+       /* return the first device found */
        for (this_dev = 0; this_dev < MAX_NE_CARDS; this_dev++) {
-               struct net_device *dev = dev_ne[this_dev];
-               if (dev) {
-                       unregister_netdev(dev);
-                       cleanup_card(dev);
-                       free_netdev(dev);
+               if (pdev_ne[this_dev]) {
+                       dev = platform_get_drvdata(pdev_ne[this_dev]);
+                       if (dev)
+                               return dev;
                }
        }
+
+       return ERR_PTR(-ENODEV);
 }
-#else /* MODULE */
-module_init(ne_init);
-module_exit(ne_exit);
 #endif /* MODULE */
+
+static void __exit ne_exit(void)
+{
+       platform_driver_unregister(&ne_driver);
+       ne_loop_rm_unreg(1);
+}
+module_exit(ne_exit);