/*******************************************************************************
Intel 10 Gigabit PCI Express Linux driver
- Copyright(c) 1999 - 2008 Intel Corporation.
+ Copyright(c) 1999 - 2010 Intel Corporation.
This program is free software; you can redistribute it and/or modify it
under the terms and conditions of the GNU General Public License,
#include "ixgbe_common.h"
#include "ixgbe_phy.h"
-static bool ixgbe_validate_phy_addr(struct ixgbe_hw *hw, u32 phy_addr);
+static void ixgbe_i2c_start(struct ixgbe_hw *hw);
+static void ixgbe_i2c_stop(struct ixgbe_hw *hw);
+static s32 ixgbe_clock_in_i2c_byte(struct ixgbe_hw *hw, u8 *data);
+static s32 ixgbe_clock_out_i2c_byte(struct ixgbe_hw *hw, u8 data);
+static s32 ixgbe_get_i2c_ack(struct ixgbe_hw *hw);
+static s32 ixgbe_clock_in_i2c_bit(struct ixgbe_hw *hw, bool *data);
+static s32 ixgbe_clock_out_i2c_bit(struct ixgbe_hw *hw, bool data);
+static s32 ixgbe_raise_i2c_clk(struct ixgbe_hw *hw, u32 *i2cctl);
+static void ixgbe_lower_i2c_clk(struct ixgbe_hw *hw, u32 *i2cctl);
+static s32 ixgbe_set_i2c_data(struct ixgbe_hw *hw, u32 *i2cctl, bool data);
+static bool ixgbe_get_i2c_data(u32 *i2cctl);
+static void ixgbe_i2c_bus_clear(struct ixgbe_hw *hw);
static enum ixgbe_phy_type ixgbe_get_phy_type_from_id(u32 phy_id);
static s32 ixgbe_get_phy_id(struct ixgbe_hw *hw);
if (hw->phy.type == ixgbe_phy_unknown) {
for (phy_addr = 0; phy_addr < IXGBE_MAX_PHY_ADDR; phy_addr++) {
- if (ixgbe_validate_phy_addr(hw, phy_addr)) {
- hw->phy.addr = phy_addr;
+ hw->phy.mdio.prtad = phy_addr;
+ if (mdio45_probe(&hw->phy.mdio, phy_addr) == 0) {
ixgbe_get_phy_id(hw);
hw->phy.type =
ixgbe_get_phy_type_from_id(hw->phy.id);
break;
}
}
+ /* clear value if nothing found */
+ hw->phy.mdio.prtad = 0;
} else {
status = 0;
}
}
/**
- * ixgbe_validate_phy_addr - Determines phy address is valid
- * @hw: pointer to hardware structure
- *
- **/
-static bool ixgbe_validate_phy_addr(struct ixgbe_hw *hw, u32 phy_addr)
-{
- u16 phy_id = 0;
- bool valid = false;
-
- hw->phy.addr = phy_addr;
- hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_ID_HIGH,
- IXGBE_MDIO_PMA_PMD_DEV_TYPE, &phy_id);
-
- if (phy_id != 0xFFFF && phy_id != 0x0)
- valid = true;
-
- return valid;
-}
-
-/**
* ixgbe_get_phy_id - Get the phy type
* @hw: pointer to hardware structure
*
u16 phy_id_high = 0;
u16 phy_id_low = 0;
- status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_ID_HIGH,
- IXGBE_MDIO_PMA_PMD_DEV_TYPE,
+ status = hw->phy.ops.read_reg(hw, MDIO_DEVID1, MDIO_MMD_PMAPMD,
&phy_id_high);
if (status == 0) {
hw->phy.id = (u32)(phy_id_high << 16);
- status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_ID_LOW,
- IXGBE_MDIO_PMA_PMD_DEV_TYPE,
+ status = hw->phy.ops.read_reg(hw, MDIO_DEVID2, MDIO_MMD_PMAPMD,
&phy_id_low);
hw->phy.id |= (u32)(phy_id_low & IXGBE_PHY_REVISION_MASK);
hw->phy.revision = (u32)(phy_id_low & ~IXGBE_PHY_REVISION_MASK);
enum ixgbe_phy_type phy_type;
switch (phy_id) {
+ case TN1010_PHY_ID:
+ phy_type = ixgbe_phy_tn;
+ break;
case QT2022_PHY_ID:
phy_type = ixgbe_phy_qt;
break;
+ case ATH_PHY_ID:
+ phy_type = ixgbe_phy_nl;
+ break;
default:
phy_type = ixgbe_phy_unknown;
break;
* Perform soft PHY reset to the PHY_XS.
* This will cause a soft reset to the PHY
*/
- return hw->phy.ops.write_reg(hw, IXGBE_MDIO_PHY_XS_CONTROL,
- IXGBE_MDIO_PHY_XS_DEV_TYPE,
- IXGBE_MDIO_PHY_XS_RESET);
+ return hw->phy.ops.write_reg(hw, MDIO_CTRL1, MDIO_MMD_PHYXS,
+ MDIO_CTRL1_RESET);
}
/**
/* Setup and write the address cycle command */
command = ((reg_addr << IXGBE_MSCA_NP_ADDR_SHIFT) |
(device_type << IXGBE_MSCA_DEV_TYPE_SHIFT) |
- (hw->phy.addr << IXGBE_MSCA_PHY_ADDR_SHIFT) |
+ (hw->phy.mdio.prtad << IXGBE_MSCA_PHY_ADDR_SHIFT) |
(IXGBE_MSCA_ADDR_CYCLE | IXGBE_MSCA_MDI_COMMAND));
IXGBE_WRITE_REG(hw, IXGBE_MSCA, command);
*/
command = ((reg_addr << IXGBE_MSCA_NP_ADDR_SHIFT) |
(device_type << IXGBE_MSCA_DEV_TYPE_SHIFT) |
- (hw->phy.addr << IXGBE_MSCA_PHY_ADDR_SHIFT) |
+ (hw->phy.mdio.prtad <<
+ IXGBE_MSCA_PHY_ADDR_SHIFT) |
(IXGBE_MSCA_READ | IXGBE_MSCA_MDI_COMMAND));
IXGBE_WRITE_REG(hw, IXGBE_MSCA, command);
/* Setup and write the address cycle command */
command = ((reg_addr << IXGBE_MSCA_NP_ADDR_SHIFT) |
(device_type << IXGBE_MSCA_DEV_TYPE_SHIFT) |
- (hw->phy.addr << IXGBE_MSCA_PHY_ADDR_SHIFT) |
+ (hw->phy.mdio.prtad << IXGBE_MSCA_PHY_ADDR_SHIFT) |
(IXGBE_MSCA_ADDR_CYCLE | IXGBE_MSCA_MDI_COMMAND));
IXGBE_WRITE_REG(hw, IXGBE_MSCA, command);
*/
command = ((reg_addr << IXGBE_MSCA_NP_ADDR_SHIFT) |
(device_type << IXGBE_MSCA_DEV_TYPE_SHIFT) |
- (hw->phy.addr << IXGBE_MSCA_PHY_ADDR_SHIFT) |
+ (hw->phy.mdio.prtad <<
+ IXGBE_MSCA_PHY_ADDR_SHIFT) |
(IXGBE_MSCA_WRITE | IXGBE_MSCA_MDI_COMMAND));
IXGBE_WRITE_REG(hw, IXGBE_MSCA, command);
s32 status = IXGBE_NOT_IMPLEMENTED;
u32 time_out;
u32 max_time_out = 10;
- u16 autoneg_reg = IXGBE_MII_AUTONEG_REG;
+ u16 autoneg_reg;
/*
* Set advertisement settings in PHY based on autoneg_advertised
* tnx devices cannot be "forced" to a autoneg 10G and fail. But can
* for a 1G.
*/
- hw->phy.ops.read_reg(hw, IXGBE_MII_SPEED_SELECTION_REG,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE, &autoneg_reg);
+ hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE, MDIO_MMD_AN, &autoneg_reg);
if (hw->phy.autoneg_advertised == IXGBE_LINK_SPEED_1GB_FULL)
- autoneg_reg &= 0xEFFF; /* 0 in bit 12 is 1G operation */
+ autoneg_reg &= ~MDIO_AN_10GBT_CTRL_ADV10G;
else
- autoneg_reg |= 0x1000; /* 1 in bit 12 is 10G/1G operation */
+ autoneg_reg |= MDIO_AN_10GBT_CTRL_ADV10G;
- hw->phy.ops.write_reg(hw, IXGBE_MII_SPEED_SELECTION_REG,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE, autoneg_reg);
+ hw->phy.ops.write_reg(hw, MDIO_AN_ADVERTISE, MDIO_MMD_AN, autoneg_reg);
/* Restart PHY autonegotiation and wait for completion */
- hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE, &autoneg_reg);
+ hw->phy.ops.read_reg(hw, MDIO_CTRL1, MDIO_MMD_AN, &autoneg_reg);
- autoneg_reg |= IXGBE_MII_RESTART;
+ autoneg_reg |= MDIO_AN_CTRL1_RESTART;
- hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE, autoneg_reg);
+ hw->phy.ops.write_reg(hw, MDIO_CTRL1, MDIO_MMD_AN, autoneg_reg);
/* Wait for autonegotiation to finish */
for (time_out = 0; time_out < max_time_out; time_out++) {
udelay(10);
/* Restart PHY autonegotiation and wait for completion */
- status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ status = hw->phy.ops.read_reg(hw, MDIO_STAT1, MDIO_MMD_AN,
&autoneg_reg);
- autoneg_reg &= IXGBE_MII_AUTONEG_COMPLETE;
- if (autoneg_reg == IXGBE_MII_AUTONEG_COMPLETE) {
+ autoneg_reg &= MDIO_AN_STAT1_COMPLETE;
+ if (autoneg_reg == MDIO_AN_STAT1_COMPLETE) {
status = 0;
break;
}
return 0;
}
+/**
+ * ixgbe_reset_phy_nl - Performs a PHY reset
+ * @hw: pointer to hardware structure
+ **/
+s32 ixgbe_reset_phy_nl(struct ixgbe_hw *hw)
+{
+ u16 phy_offset, control, eword, edata, block_crc;
+ bool end_data = false;
+ u16 list_offset, data_offset;
+ u16 phy_data = 0;
+ s32 ret_val = 0;
+ u32 i;
+
+ hw->phy.ops.read_reg(hw, MDIO_CTRL1, MDIO_MMD_PHYXS, &phy_data);
+
+ /* reset the PHY and poll for completion */
+ hw->phy.ops.write_reg(hw, MDIO_CTRL1, MDIO_MMD_PHYXS,
+ (phy_data | MDIO_CTRL1_RESET));
+
+ for (i = 0; i < 100; i++) {
+ hw->phy.ops.read_reg(hw, MDIO_CTRL1, MDIO_MMD_PHYXS,
+ &phy_data);
+ if ((phy_data & MDIO_CTRL1_RESET) == 0)
+ break;
+ msleep(10);
+ }
+
+ if ((phy_data & MDIO_CTRL1_RESET) != 0) {
+ hw_dbg(hw, "PHY reset did not complete.\n");
+ ret_val = IXGBE_ERR_PHY;
+ goto out;
+ }
+
+ /* Get init offsets */
+ ret_val = ixgbe_get_sfp_init_sequence_offsets(hw, &list_offset,
+ &data_offset);
+ if (ret_val != 0)
+ goto out;
+
+ ret_val = hw->eeprom.ops.read(hw, data_offset, &block_crc);
+ data_offset++;
+ while (!end_data) {
+ /*
+ * Read control word from PHY init contents offset
+ */
+ ret_val = hw->eeprom.ops.read(hw, data_offset, &eword);
+ control = (eword & IXGBE_CONTROL_MASK_NL) >>
+ IXGBE_CONTROL_SHIFT_NL;
+ edata = eword & IXGBE_DATA_MASK_NL;
+ switch (control) {
+ case IXGBE_DELAY_NL:
+ data_offset++;
+ hw_dbg(hw, "DELAY: %d MS\n", edata);
+ msleep(edata);
+ break;
+ case IXGBE_DATA_NL:
+ hw_dbg(hw, "DATA: \n");
+ data_offset++;
+ hw->eeprom.ops.read(hw, data_offset++,
+ &phy_offset);
+ for (i = 0; i < edata; i++) {
+ hw->eeprom.ops.read(hw, data_offset, &eword);
+ hw->phy.ops.write_reg(hw, phy_offset,
+ MDIO_MMD_PMAPMD, eword);
+ hw_dbg(hw, "Wrote %4.4x to %4.4x\n", eword,
+ phy_offset);
+ data_offset++;
+ phy_offset++;
+ }
+ break;
+ case IXGBE_CONTROL_NL:
+ data_offset++;
+ hw_dbg(hw, "CONTROL: \n");
+ if (edata == IXGBE_CONTROL_EOL_NL) {
+ hw_dbg(hw, "EOL\n");
+ end_data = true;
+ } else if (edata == IXGBE_CONTROL_SOL_NL) {
+ hw_dbg(hw, "SOL\n");
+ } else {
+ hw_dbg(hw, "Bad control value\n");
+ ret_val = IXGBE_ERR_PHY;
+ goto out;
+ }
+ break;
+ default:
+ hw_dbg(hw, "Bad control type\n");
+ ret_val = IXGBE_ERR_PHY;
+ goto out;
+ }
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * ixgbe_identify_sfp_module_generic - Identifies SFP module and assigns
+ * the PHY type.
+ * @hw: pointer to hardware structure
+ *
+ * Searches for and indentifies the SFP module. Assings appropriate PHY type.
+ **/
+s32 ixgbe_identify_sfp_module_generic(struct ixgbe_hw *hw)
+{
+ s32 status = IXGBE_ERR_PHY_ADDR_INVALID;
+ u32 vendor_oui = 0;
+ enum ixgbe_sfp_type stored_sfp_type = hw->phy.sfp_type;
+ u8 identifier = 0;
+ u8 comp_codes_1g = 0;
+ u8 comp_codes_10g = 0;
+ u8 oui_bytes[3] = {0, 0, 0};
+ u8 cable_tech = 0;
+ u16 enforce_sfp = 0;
+
+ if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_fiber) {
+ hw->phy.sfp_type = ixgbe_sfp_type_not_present;
+ status = IXGBE_ERR_SFP_NOT_PRESENT;
+ goto out;
+ }
+
+ status = hw->phy.ops.read_i2c_eeprom(hw, IXGBE_SFF_IDENTIFIER,
+ &identifier);
+
+ if (status == IXGBE_ERR_SFP_NOT_PRESENT || status == IXGBE_ERR_I2C) {
+ status = IXGBE_ERR_SFP_NOT_PRESENT;
+ hw->phy.sfp_type = ixgbe_sfp_type_not_present;
+ if (hw->phy.type != ixgbe_phy_nl) {
+ hw->phy.id = 0;
+ hw->phy.type = ixgbe_phy_unknown;
+ }
+ goto out;
+ }
+
+ if (identifier == IXGBE_SFF_IDENTIFIER_SFP) {
+ hw->phy.ops.read_i2c_eeprom(hw, IXGBE_SFF_1GBE_COMP_CODES,
+ &comp_codes_1g);
+ hw->phy.ops.read_i2c_eeprom(hw, IXGBE_SFF_10GBE_COMP_CODES,
+ &comp_codes_10g);
+ hw->phy.ops.read_i2c_eeprom(hw, IXGBE_SFF_CABLE_TECHNOLOGY,
+ &cable_tech);
+
+ /* ID Module
+ * =========
+ * 0 SFP_DA_CU
+ * 1 SFP_SR
+ * 2 SFP_LR
+ * 3 SFP_DA_CORE0 - 82599-specific
+ * 4 SFP_DA_CORE1 - 82599-specific
+ * 5 SFP_SR/LR_CORE0 - 82599-specific
+ * 6 SFP_SR/LR_CORE1 - 82599-specific
+ */
+ if (hw->mac.type == ixgbe_mac_82598EB) {
+ if (cable_tech & IXGBE_SFF_DA_PASSIVE_CABLE)
+ hw->phy.sfp_type = ixgbe_sfp_type_da_cu;
+ else if (comp_codes_10g & IXGBE_SFF_10GBASESR_CAPABLE)
+ hw->phy.sfp_type = ixgbe_sfp_type_sr;
+ else if (comp_codes_10g & IXGBE_SFF_10GBASELR_CAPABLE)
+ hw->phy.sfp_type = ixgbe_sfp_type_lr;
+ else
+ hw->phy.sfp_type = ixgbe_sfp_type_unknown;
+ } else if (hw->mac.type == ixgbe_mac_82599EB) {
+ if (cable_tech & IXGBE_SFF_DA_PASSIVE_CABLE)
+ if (hw->bus.lan_id == 0)
+ hw->phy.sfp_type =
+ ixgbe_sfp_type_da_cu_core0;
+ else
+ hw->phy.sfp_type =
+ ixgbe_sfp_type_da_cu_core1;
+ else if (comp_codes_10g & IXGBE_SFF_10GBASESR_CAPABLE)
+ if (hw->bus.lan_id == 0)
+ hw->phy.sfp_type =
+ ixgbe_sfp_type_srlr_core0;
+ else
+ hw->phy.sfp_type =
+ ixgbe_sfp_type_srlr_core1;
+ else if (comp_codes_10g & IXGBE_SFF_10GBASELR_CAPABLE)
+ if (hw->bus.lan_id == 0)
+ hw->phy.sfp_type =
+ ixgbe_sfp_type_srlr_core0;
+ else
+ hw->phy.sfp_type =
+ ixgbe_sfp_type_srlr_core1;
+ else
+ hw->phy.sfp_type = ixgbe_sfp_type_unknown;
+ }
+
+ if (hw->phy.sfp_type != stored_sfp_type)
+ hw->phy.sfp_setup_needed = true;
+
+ /* Determine if the SFP+ PHY is dual speed or not. */
+ hw->phy.multispeed_fiber = false;
+ if (((comp_codes_1g & IXGBE_SFF_1GBASESX_CAPABLE) &&
+ (comp_codes_10g & IXGBE_SFF_10GBASESR_CAPABLE)) ||
+ ((comp_codes_1g & IXGBE_SFF_1GBASELX_CAPABLE) &&
+ (comp_codes_10g & IXGBE_SFF_10GBASELR_CAPABLE)))
+ hw->phy.multispeed_fiber = true;
+
+ /* Determine PHY vendor */
+ if (hw->phy.type != ixgbe_phy_nl) {
+ hw->phy.id = identifier;
+ hw->phy.ops.read_i2c_eeprom(hw,
+ IXGBE_SFF_VENDOR_OUI_BYTE0,
+ &oui_bytes[0]);
+ hw->phy.ops.read_i2c_eeprom(hw,
+ IXGBE_SFF_VENDOR_OUI_BYTE1,
+ &oui_bytes[1]);
+ hw->phy.ops.read_i2c_eeprom(hw,
+ IXGBE_SFF_VENDOR_OUI_BYTE2,
+ &oui_bytes[2]);
+
+ vendor_oui =
+ ((oui_bytes[0] << IXGBE_SFF_VENDOR_OUI_BYTE0_SHIFT) |
+ (oui_bytes[1] << IXGBE_SFF_VENDOR_OUI_BYTE1_SHIFT) |
+ (oui_bytes[2] << IXGBE_SFF_VENDOR_OUI_BYTE2_SHIFT));
+
+ switch (vendor_oui) {
+ case IXGBE_SFF_VENDOR_OUI_TYCO:
+ if (cable_tech & IXGBE_SFF_DA_PASSIVE_CABLE)
+ hw->phy.type = ixgbe_phy_tw_tyco;
+ break;
+ case IXGBE_SFF_VENDOR_OUI_FTL:
+ hw->phy.type = ixgbe_phy_sfp_ftl;
+ break;
+ case IXGBE_SFF_VENDOR_OUI_AVAGO:
+ hw->phy.type = ixgbe_phy_sfp_avago;
+ break;
+ case IXGBE_SFF_VENDOR_OUI_INTEL:
+ hw->phy.type = ixgbe_phy_sfp_intel;
+ break;
+ default:
+ if (cable_tech & IXGBE_SFF_DA_PASSIVE_CABLE)
+ hw->phy.type = ixgbe_phy_tw_unknown;
+ else
+ hw->phy.type = ixgbe_phy_sfp_unknown;
+ break;
+ }
+ }
+
+ /* All passive DA cables are supported */
+ if (cable_tech & IXGBE_SFF_DA_PASSIVE_CABLE) {
+ status = 0;
+ goto out;
+ }
+
+ /* 1G SFP modules are not supported */
+ if (comp_codes_10g == 0) {
+ hw->phy.type = ixgbe_phy_sfp_unsupported;
+ status = IXGBE_ERR_SFP_NOT_SUPPORTED;
+ goto out;
+ }
+
+ /* Anything else 82598-based is supported */
+ if (hw->mac.type == ixgbe_mac_82598EB) {
+ status = 0;
+ goto out;
+ }
+
+ /* This is guaranteed to be 82599, no need to check for NULL */
+ hw->mac.ops.get_device_caps(hw, &enforce_sfp);
+ if (!(enforce_sfp & IXGBE_DEVICE_CAPS_ALLOW_ANY_SFP)) {
+ /* Make sure we're a supported PHY type */
+ if (hw->phy.type == ixgbe_phy_sfp_intel) {
+ status = 0;
+ } else {
+ hw_dbg(hw, "SFP+ module not supported\n");
+ hw->phy.type = ixgbe_phy_sfp_unsupported;
+ status = IXGBE_ERR_SFP_NOT_SUPPORTED;
+ }
+ } else {
+ status = 0;
+ }
+ }
+
+out:
+ return status;
+}
+
+/**
+ * ixgbe_get_sfp_init_sequence_offsets - Checks the MAC's EEPROM to see
+ * if it supports a given SFP+ module type, if so it returns the offsets to the
+ * phy init sequence block.
+ * @hw: pointer to hardware structure
+ * @list_offset: offset to the SFP ID list
+ * @data_offset: offset to the SFP data block
+ **/
+s32 ixgbe_get_sfp_init_sequence_offsets(struct ixgbe_hw *hw,
+ u16 *list_offset,
+ u16 *data_offset)
+{
+ u16 sfp_id;
+
+ if (hw->phy.sfp_type == ixgbe_sfp_type_unknown)
+ return IXGBE_ERR_SFP_NOT_SUPPORTED;
+
+ if (hw->phy.sfp_type == ixgbe_sfp_type_not_present)
+ return IXGBE_ERR_SFP_NOT_PRESENT;
+
+ if ((hw->device_id == IXGBE_DEV_ID_82598_SR_DUAL_PORT_EM) &&
+ (hw->phy.sfp_type == ixgbe_sfp_type_da_cu))
+ return IXGBE_ERR_SFP_NOT_SUPPORTED;
+
+ /* Read offset to PHY init contents */
+ hw->eeprom.ops.read(hw, IXGBE_PHY_INIT_OFFSET_NL, list_offset);
+
+ if ((!*list_offset) || (*list_offset == 0xFFFF))
+ return IXGBE_ERR_SFP_NO_INIT_SEQ_PRESENT;
+
+ /* Shift offset to first ID word */
+ (*list_offset)++;
+
+ /*
+ * Find the matching SFP ID in the EEPROM
+ * and program the init sequence
+ */
+ hw->eeprom.ops.read(hw, *list_offset, &sfp_id);
+
+ while (sfp_id != IXGBE_PHY_INIT_END_NL) {
+ if (sfp_id == hw->phy.sfp_type) {
+ (*list_offset)++;
+ hw->eeprom.ops.read(hw, *list_offset, data_offset);
+ if ((!*data_offset) || (*data_offset == 0xFFFF)) {
+ hw_dbg(hw, "SFP+ module not supported\n");
+ return IXGBE_ERR_SFP_NOT_SUPPORTED;
+ } else {
+ break;
+ }
+ } else {
+ (*list_offset) += 2;
+ if (hw->eeprom.ops.read(hw, *list_offset, &sfp_id))
+ return IXGBE_ERR_PHY;
+ }
+ }
+
+ if (sfp_id == IXGBE_PHY_INIT_END_NL) {
+ hw_dbg(hw, "No matching SFP+ module found\n");
+ return IXGBE_ERR_SFP_NOT_SUPPORTED;
+ }
+
+ return 0;
+}
+
+/**
+ * ixgbe_read_i2c_eeprom_generic - Reads 8 bit EEPROM word over I2C interface
+ * @hw: pointer to hardware structure
+ * @byte_offset: EEPROM byte offset to read
+ * @eeprom_data: value read
+ *
+ * Performs byte read operation to SFP module's EEPROM over I2C interface.
+ **/
+s32 ixgbe_read_i2c_eeprom_generic(struct ixgbe_hw *hw, u8 byte_offset,
+ u8 *eeprom_data)
+{
+ return hw->phy.ops.read_i2c_byte(hw, byte_offset,
+ IXGBE_I2C_EEPROM_DEV_ADDR,
+ eeprom_data);
+}
+
+/**
+ * ixgbe_write_i2c_eeprom_generic - Writes 8 bit EEPROM word over I2C interface
+ * @hw: pointer to hardware structure
+ * @byte_offset: EEPROM byte offset to write
+ * @eeprom_data: value to write
+ *
+ * Performs byte write operation to SFP module's EEPROM over I2C interface.
+ **/
+s32 ixgbe_write_i2c_eeprom_generic(struct ixgbe_hw *hw, u8 byte_offset,
+ u8 eeprom_data)
+{
+ return hw->phy.ops.write_i2c_byte(hw, byte_offset,
+ IXGBE_I2C_EEPROM_DEV_ADDR,
+ eeprom_data);
+}
+
+/**
+ * ixgbe_read_i2c_byte_generic - Reads 8 bit word over I2C
+ * @hw: pointer to hardware structure
+ * @byte_offset: byte offset to read
+ * @data: value read
+ *
+ * Performs byte read operation to SFP module's EEPROM over I2C interface at
+ * a specified deivce address.
+ **/
+s32 ixgbe_read_i2c_byte_generic(struct ixgbe_hw *hw, u8 byte_offset,
+ u8 dev_addr, u8 *data)
+{
+ s32 status = 0;
+ u32 max_retry = 1;
+ u32 retry = 0;
+ bool nack = 1;
+
+ do {
+ ixgbe_i2c_start(hw);
+
+ /* Device Address and write indication */
+ status = ixgbe_clock_out_i2c_byte(hw, dev_addr);
+ if (status != 0)
+ goto fail;
+
+ status = ixgbe_get_i2c_ack(hw);
+ if (status != 0)
+ goto fail;
+
+ status = ixgbe_clock_out_i2c_byte(hw, byte_offset);
+ if (status != 0)
+ goto fail;
+
+ status = ixgbe_get_i2c_ack(hw);
+ if (status != 0)
+ goto fail;
+
+ ixgbe_i2c_start(hw);
+
+ /* Device Address and read indication */
+ status = ixgbe_clock_out_i2c_byte(hw, (dev_addr | 0x1));
+ if (status != 0)
+ goto fail;
+
+ status = ixgbe_get_i2c_ack(hw);
+ if (status != 0)
+ goto fail;
+
+ status = ixgbe_clock_in_i2c_byte(hw, data);
+ if (status != 0)
+ goto fail;
+
+ status = ixgbe_clock_out_i2c_bit(hw, nack);
+ if (status != 0)
+ goto fail;
+
+ ixgbe_i2c_stop(hw);
+ break;
+
+fail:
+ ixgbe_i2c_bus_clear(hw);
+ retry++;
+ if (retry < max_retry)
+ hw_dbg(hw, "I2C byte read error - Retrying.\n");
+ else
+ hw_dbg(hw, "I2C byte read error.\n");
+
+ } while (retry < max_retry);
+
+ return status;
+}
+
+/**
+ * ixgbe_write_i2c_byte_generic - Writes 8 bit word over I2C
+ * @hw: pointer to hardware structure
+ * @byte_offset: byte offset to write
+ * @data: value to write
+ *
+ * Performs byte write operation to SFP module's EEPROM over I2C interface at
+ * a specified device address.
+ **/
+s32 ixgbe_write_i2c_byte_generic(struct ixgbe_hw *hw, u8 byte_offset,
+ u8 dev_addr, u8 data)
+{
+ s32 status = 0;
+ u32 max_retry = 1;
+ u32 retry = 0;
+
+ do {
+ ixgbe_i2c_start(hw);
+
+ status = ixgbe_clock_out_i2c_byte(hw, dev_addr);
+ if (status != 0)
+ goto fail;
+
+ status = ixgbe_get_i2c_ack(hw);
+ if (status != 0)
+ goto fail;
+
+ status = ixgbe_clock_out_i2c_byte(hw, byte_offset);
+ if (status != 0)
+ goto fail;
+
+ status = ixgbe_get_i2c_ack(hw);
+ if (status != 0)
+ goto fail;
+
+ status = ixgbe_clock_out_i2c_byte(hw, data);
+ if (status != 0)
+ goto fail;
+
+ status = ixgbe_get_i2c_ack(hw);
+ if (status != 0)
+ goto fail;
+
+ ixgbe_i2c_stop(hw);
+ break;
+
+fail:
+ ixgbe_i2c_bus_clear(hw);
+ retry++;
+ if (retry < max_retry)
+ hw_dbg(hw, "I2C byte write error - Retrying.\n");
+ else
+ hw_dbg(hw, "I2C byte write error.\n");
+ } while (retry < max_retry);
+
+ return status;
+}
+
+/**
+ * ixgbe_i2c_start - Sets I2C start condition
+ * @hw: pointer to hardware structure
+ *
+ * Sets I2C start condition (High -> Low on SDA while SCL is High)
+ **/
+static void ixgbe_i2c_start(struct ixgbe_hw *hw)
+{
+ u32 i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL);
+
+ /* Start condition must begin with data and clock high */
+ ixgbe_set_i2c_data(hw, &i2cctl, 1);
+ ixgbe_raise_i2c_clk(hw, &i2cctl);
+
+ /* Setup time for start condition (4.7us) */
+ udelay(IXGBE_I2C_T_SU_STA);
+
+ ixgbe_set_i2c_data(hw, &i2cctl, 0);
+
+ /* Hold time for start condition (4us) */
+ udelay(IXGBE_I2C_T_HD_STA);
+
+ ixgbe_lower_i2c_clk(hw, &i2cctl);
+
+ /* Minimum low period of clock is 4.7 us */
+ udelay(IXGBE_I2C_T_LOW);
+
+}
+
+/**
+ * ixgbe_i2c_stop - Sets I2C stop condition
+ * @hw: pointer to hardware structure
+ *
+ * Sets I2C stop condition (Low -> High on SDA while SCL is High)
+ **/
+static void ixgbe_i2c_stop(struct ixgbe_hw *hw)
+{
+ u32 i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL);
+
+ /* Stop condition must begin with data low and clock high */
+ ixgbe_set_i2c_data(hw, &i2cctl, 0);
+ ixgbe_raise_i2c_clk(hw, &i2cctl);
+
+ /* Setup time for stop condition (4us) */
+ udelay(IXGBE_I2C_T_SU_STO);
+
+ ixgbe_set_i2c_data(hw, &i2cctl, 1);
+
+ /* bus free time between stop and start (4.7us)*/
+ udelay(IXGBE_I2C_T_BUF);
+}
+
+/**
+ * ixgbe_clock_in_i2c_byte - Clocks in one byte via I2C
+ * @hw: pointer to hardware structure
+ * @data: data byte to clock in
+ *
+ * Clocks in one byte data via I2C data/clock
+ **/
+static s32 ixgbe_clock_in_i2c_byte(struct ixgbe_hw *hw, u8 *data)
+{
+ s32 status = 0;
+ s32 i;
+ bool bit = 0;
+
+ for (i = 7; i >= 0; i--) {
+ status = ixgbe_clock_in_i2c_bit(hw, &bit);
+ *data |= bit << i;
+
+ if (status != 0)
+ break;
+ }
+
+ return status;
+}
+
+/**
+ * ixgbe_clock_out_i2c_byte - Clocks out one byte via I2C
+ * @hw: pointer to hardware structure
+ * @data: data byte clocked out
+ *
+ * Clocks out one byte data via I2C data/clock
+ **/
+static s32 ixgbe_clock_out_i2c_byte(struct ixgbe_hw *hw, u8 data)
+{
+ s32 status = 0;
+ s32 i;
+ u32 i2cctl;
+ bool bit = 0;
+
+ for (i = 7; i >= 0; i--) {
+ bit = (data >> i) & 0x1;
+ status = ixgbe_clock_out_i2c_bit(hw, bit);
+
+ if (status != 0)
+ break;
+ }
+
+ /* Release SDA line (set high) */
+ i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL);
+ i2cctl |= IXGBE_I2C_DATA_OUT;
+ IXGBE_WRITE_REG(hw, IXGBE_I2CCTL, i2cctl);
+
+ return status;
+}
+
+/**
+ * ixgbe_get_i2c_ack - Polls for I2C ACK
+ * @hw: pointer to hardware structure
+ *
+ * Clocks in/out one bit via I2C data/clock
+ **/
+static s32 ixgbe_get_i2c_ack(struct ixgbe_hw *hw)
+{
+ s32 status;
+ u32 i = 0;
+ u32 i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL);
+ u32 timeout = 10;
+ bool ack = 1;
+
+ status = ixgbe_raise_i2c_clk(hw, &i2cctl);
+
+ if (status != 0)
+ goto out;
+
+ /* Minimum high period of clock is 4us */
+ udelay(IXGBE_I2C_T_HIGH);
+
+ /* Poll for ACK. Note that ACK in I2C spec is
+ * transition from 1 to 0 */
+ for (i = 0; i < timeout; i++) {
+ i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL);
+ ack = ixgbe_get_i2c_data(&i2cctl);
+
+ udelay(1);
+ if (ack == 0)
+ break;
+ }
+
+ if (ack == 1) {
+ hw_dbg(hw, "I2C ack was not received.\n");
+ status = IXGBE_ERR_I2C;
+ }
+
+ ixgbe_lower_i2c_clk(hw, &i2cctl);
+
+ /* Minimum low period of clock is 4.7 us */
+ udelay(IXGBE_I2C_T_LOW);
+
+out:
+ return status;
+}
+
+/**
+ * ixgbe_clock_in_i2c_bit - Clocks in one bit via I2C data/clock
+ * @hw: pointer to hardware structure
+ * @data: read data value
+ *
+ * Clocks in one bit via I2C data/clock
+ **/
+static s32 ixgbe_clock_in_i2c_bit(struct ixgbe_hw *hw, bool *data)
+{
+ s32 status;
+ u32 i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL);
+
+ status = ixgbe_raise_i2c_clk(hw, &i2cctl);
+
+ /* Minimum high period of clock is 4us */
+ udelay(IXGBE_I2C_T_HIGH);
+
+ i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL);
+ *data = ixgbe_get_i2c_data(&i2cctl);
+
+ ixgbe_lower_i2c_clk(hw, &i2cctl);
+
+ /* Minimum low period of clock is 4.7 us */
+ udelay(IXGBE_I2C_T_LOW);
+
+ return status;
+}
+
+/**
+ * ixgbe_clock_out_i2c_bit - Clocks in/out one bit via I2C data/clock
+ * @hw: pointer to hardware structure
+ * @data: data value to write
+ *
+ * Clocks out one bit via I2C data/clock
+ **/
+static s32 ixgbe_clock_out_i2c_bit(struct ixgbe_hw *hw, bool data)
+{
+ s32 status;
+ u32 i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL);
+
+ status = ixgbe_set_i2c_data(hw, &i2cctl, data);
+ if (status == 0) {
+ status = ixgbe_raise_i2c_clk(hw, &i2cctl);
+
+ /* Minimum high period of clock is 4us */
+ udelay(IXGBE_I2C_T_HIGH);
+
+ ixgbe_lower_i2c_clk(hw, &i2cctl);
+
+ /* Minimum low period of clock is 4.7 us.
+ * This also takes care of the data hold time.
+ */
+ udelay(IXGBE_I2C_T_LOW);
+ } else {
+ status = IXGBE_ERR_I2C;
+ hw_dbg(hw, "I2C data was not set to %X\n", data);
+ }
+
+ return status;
+}
+/**
+ * ixgbe_raise_i2c_clk - Raises the I2C SCL clock
+ * @hw: pointer to hardware structure
+ * @i2cctl: Current value of I2CCTL register
+ *
+ * Raises the I2C clock line '0'->'1'
+ **/
+static s32 ixgbe_raise_i2c_clk(struct ixgbe_hw *hw, u32 *i2cctl)
+{
+ s32 status = 0;
+
+ *i2cctl |= IXGBE_I2C_CLK_OUT;
+
+ IXGBE_WRITE_REG(hw, IXGBE_I2CCTL, *i2cctl);
+
+ /* SCL rise time (1000ns) */
+ udelay(IXGBE_I2C_T_RISE);
+
+ return status;
+}
+
+/**
+ * ixgbe_lower_i2c_clk - Lowers the I2C SCL clock
+ * @hw: pointer to hardware structure
+ * @i2cctl: Current value of I2CCTL register
+ *
+ * Lowers the I2C clock line '1'->'0'
+ **/
+static void ixgbe_lower_i2c_clk(struct ixgbe_hw *hw, u32 *i2cctl)
+{
+
+ *i2cctl &= ~IXGBE_I2C_CLK_OUT;
+
+ IXGBE_WRITE_REG(hw, IXGBE_I2CCTL, *i2cctl);
+
+ /* SCL fall time (300ns) */
+ udelay(IXGBE_I2C_T_FALL);
+}
+
+/**
+ * ixgbe_set_i2c_data - Sets the I2C data bit
+ * @hw: pointer to hardware structure
+ * @i2cctl: Current value of I2CCTL register
+ * @data: I2C data value (0 or 1) to set
+ *
+ * Sets the I2C data bit
+ **/
+static s32 ixgbe_set_i2c_data(struct ixgbe_hw *hw, u32 *i2cctl, bool data)
+{
+ s32 status = 0;
+
+ if (data)
+ *i2cctl |= IXGBE_I2C_DATA_OUT;
+ else
+ *i2cctl &= ~IXGBE_I2C_DATA_OUT;
+
+ IXGBE_WRITE_REG(hw, IXGBE_I2CCTL, *i2cctl);
+
+ /* Data rise/fall (1000ns/300ns) and set-up time (250ns) */
+ udelay(IXGBE_I2C_T_RISE + IXGBE_I2C_T_FALL + IXGBE_I2C_T_SU_DATA);
+
+ /* Verify data was set correctly */
+ *i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL);
+ if (data != ixgbe_get_i2c_data(i2cctl)) {
+ status = IXGBE_ERR_I2C;
+ hw_dbg(hw, "Error - I2C data was not set to %X.\n", data);
+ }
+
+ return status;
+}
+
+/**
+ * ixgbe_get_i2c_data - Reads the I2C SDA data bit
+ * @hw: pointer to hardware structure
+ * @i2cctl: Current value of I2CCTL register
+ *
+ * Returns the I2C data bit value
+ **/
+static bool ixgbe_get_i2c_data(u32 *i2cctl)
+{
+ bool data;
+
+ if (*i2cctl & IXGBE_I2C_DATA_IN)
+ data = 1;
+ else
+ data = 0;
+
+ return data;
+}
+
+/**
+ * ixgbe_i2c_bus_clear - Clears the I2C bus
+ * @hw: pointer to hardware structure
+ *
+ * Clears the I2C bus by sending nine clock pulses.
+ * Used when data line is stuck low.
+ **/
+static void ixgbe_i2c_bus_clear(struct ixgbe_hw *hw)
+{
+ u32 i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL);
+ u32 i;
+
+ ixgbe_set_i2c_data(hw, &i2cctl, 1);
+
+ for (i = 0; i < 9; i++) {
+ ixgbe_raise_i2c_clk(hw, &i2cctl);
+
+ /* Min high period of clock is 4us */
+ udelay(IXGBE_I2C_T_HIGH);
+
+ ixgbe_lower_i2c_clk(hw, &i2cctl);
+
+ /* Min low period of clock is 4.7us*/
+ udelay(IXGBE_I2C_T_LOW);
+ }
+
+ /* Put the i2c bus back to default state */
+ ixgbe_i2c_stop(hw);
+}
+
+/**
+ * ixgbe_check_phy_link_tnx - Determine link and speed status
+ * @hw: pointer to hardware structure
+ *
+ * Reads the VS1 register to determine if link is up and the current speed for
+ * the PHY.
+ **/
+s32 ixgbe_check_phy_link_tnx(struct ixgbe_hw *hw, ixgbe_link_speed *speed,
+ bool *link_up)
+{
+ s32 status = 0;
+ u32 time_out;
+ u32 max_time_out = 10;
+ u16 phy_link = 0;
+ u16 phy_speed = 0;
+ u16 phy_data = 0;
+
+ /* Initialize speed and link to default case */
+ *link_up = false;
+ *speed = IXGBE_LINK_SPEED_10GB_FULL;
+
+ /*
+ * Check current speed and link status of the PHY register.
+ * This is a vendor specific register and may have to
+ * be changed for other copper PHYs.
+ */
+ for (time_out = 0; time_out < max_time_out; time_out++) {
+ udelay(10);
+ status = hw->phy.ops.read_reg(hw,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_STATUS,
+ MDIO_MMD_VEND1,
+ &phy_data);
+ phy_link = phy_data &
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_LINK_STATUS;
+ phy_speed = phy_data &
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_SPEED_STATUS;
+ if (phy_link == IXGBE_MDIO_VENDOR_SPECIFIC_1_LINK_STATUS) {
+ *link_up = true;
+ if (phy_speed ==
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_SPEED_STATUS)
+ *speed = IXGBE_LINK_SPEED_1GB_FULL;
+ break;
+ }
+ }
+
+ return status;
+}
+
+/**
+ * ixgbe_get_phy_firmware_version_tnx - Gets the PHY Firmware Version
+ * @hw: pointer to hardware structure
+ * @firmware_version: pointer to the PHY Firmware Version
+ **/
+s32 ixgbe_get_phy_firmware_version_tnx(struct ixgbe_hw *hw,
+ u16 *firmware_version)
+{
+ s32 status = 0;
+
+ status = hw->phy.ops.read_reg(hw, TNX_FW_REV, MDIO_MMD_VEND1,
+ firmware_version);
+
+ return status;
+}
+
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff