/*******************************************************************************
Intel 10 Gigabit PCI Express Linux driver
- Copyright(c) 1999 - 2009 Intel Corporation.
+ Copyright(c) 1999 - 2010 Intel Corporation.
This program is free software; you can redistribute it and/or modify it
under the terms and conditions of the GNU General Public License,
static s32 ixgbe_get_copper_link_capabilities_82598(struct ixgbe_hw *hw,
ixgbe_link_speed *speed,
bool *autoneg);
-static s32 ixgbe_setup_copper_link_82598(struct ixgbe_hw *hw);
-static s32 ixgbe_setup_copper_link_speed_82598(struct ixgbe_hw *hw,
- ixgbe_link_speed speed,
- bool autoneg,
- bool autoneg_wait_to_complete);
+static s32 ixgbe_setup_copper_link_82598(struct ixgbe_hw *hw,
+ ixgbe_link_speed speed,
+ bool autoneg,
+ bool autoneg_wait_to_complete);
static s32 ixgbe_read_i2c_eeprom_82598(struct ixgbe_hw *hw, u8 byte_offset,
u8 *eeprom_data);
/**
+ * ixgbe_set_pcie_completion_timeout - set pci-e completion timeout
+ * @hw: pointer to the HW structure
+ *
+ * The defaults for 82598 should be in the range of 50us to 50ms,
+ * however the hardware default for these parts is 500us to 1ms which is less
+ * than the 10ms recommended by the pci-e spec. To address this we need to
+ * increase the value to either 10ms to 250ms for capability version 1 config,
+ * or 16ms to 55ms for version 2.
+ **/
+static void ixgbe_set_pcie_completion_timeout(struct ixgbe_hw *hw)
+{
+ struct ixgbe_adapter *adapter = hw->back;
+ u32 gcr = IXGBE_READ_REG(hw, IXGBE_GCR);
+ u16 pcie_devctl2;
+
+ /* only take action if timeout value is defaulted to 0 */
+ if (gcr & IXGBE_GCR_CMPL_TMOUT_MASK)
+ goto out;
+
+ /*
+ * if capababilities version is type 1 we can write the
+ * timeout of 10ms to 250ms through the GCR register
+ */
+ if (!(gcr & IXGBE_GCR_CAP_VER2)) {
+ gcr |= IXGBE_GCR_CMPL_TMOUT_10ms;
+ goto out;
+ }
+
+ /*
+ * for version 2 capabilities we need to write the config space
+ * directly in order to set the completion timeout value for
+ * 16ms to 55ms
+ */
+ pci_read_config_word(adapter->pdev,
+ IXGBE_PCI_DEVICE_CONTROL2, &pcie_devctl2);
+ pcie_devctl2 |= IXGBE_PCI_DEVICE_CONTROL2_16ms;
+ pci_write_config_word(adapter->pdev,
+ IXGBE_PCI_DEVICE_CONTROL2, pcie_devctl2);
+out:
+ /* disable completion timeout resend */
+ gcr &= ~IXGBE_GCR_CMPL_TMOUT_RESEND;
+ IXGBE_WRITE_REG(hw, IXGBE_GCR, gcr);
+}
+
+/**
* ixgbe_get_pcie_msix_count_82598 - Gets MSI-X vector count
* @hw: pointer to hardware structure
*
* Read PCIe configuration space, and get the MSI-X vector count from
* the capabilities table.
**/
-u16 ixgbe_get_pcie_msix_count_82598(struct ixgbe_hw *hw)
+static u16 ixgbe_get_pcie_msix_count_82598(struct ixgbe_hw *hw)
{
struct ixgbe_adapter *adapter = hw->back;
u16 msix_count;
static s32 ixgbe_get_invariants_82598(struct ixgbe_hw *hw)
{
struct ixgbe_mac_info *mac = &hw->mac;
+
+ /* Call PHY identify routine to get the phy type */
+ ixgbe_identify_phy_generic(hw);
+
+ mac->mcft_size = IXGBE_82598_MC_TBL_SIZE;
+ mac->vft_size = IXGBE_82598_VFT_TBL_SIZE;
+ mac->num_rar_entries = IXGBE_82598_RAR_ENTRIES;
+ mac->max_rx_queues = IXGBE_82598_MAX_RX_QUEUES;
+ mac->max_tx_queues = IXGBE_82598_MAX_TX_QUEUES;
+ mac->max_msix_vectors = ixgbe_get_pcie_msix_count_82598(hw);
+
+ return 0;
+}
+
+/**
+ * ixgbe_init_phy_ops_82598 - PHY/SFP specific init
+ * @hw: pointer to hardware structure
+ *
+ * Initialize any function pointers that were not able to be
+ * set during get_invariants because the PHY/SFP type was
+ * not known. Perform the SFP init if necessary.
+ *
+ **/
+static s32 ixgbe_init_phy_ops_82598(struct ixgbe_hw *hw)
+{
+ struct ixgbe_mac_info *mac = &hw->mac;
struct ixgbe_phy_info *phy = &hw->phy;
s32 ret_val = 0;
u16 list_offset, data_offset;
- /* Call PHY identify routine to get the phy type */
- ixgbe_identify_phy_generic(hw);
+ /* Identify the PHY */
+ phy->ops.identify(hw);
+
+ /* Overwrite the link function pointers if copper PHY */
+ if (mac->ops.get_media_type(hw) == ixgbe_media_type_copper) {
+ mac->ops.setup_link = &ixgbe_setup_copper_link_82598;
+ mac->ops.get_link_capabilities =
+ &ixgbe_get_copper_link_capabilities_82598;
+ }
- /* PHY Init */
- switch (phy->type) {
+ switch (hw->phy.type) {
case ixgbe_phy_tn:
phy->ops.check_link = &ixgbe_check_phy_link_tnx;
phy->ops.get_firmware_version =
/* Check to see if SFP+ module is supported */
ret_val = ixgbe_get_sfp_init_sequence_offsets(hw,
- &list_offset,
- &data_offset);
+ &list_offset,
+ &data_offset);
if (ret_val != 0) {
ret_val = IXGBE_ERR_SFP_NOT_SUPPORTED;
goto out;
break;
}
- if (mac->ops.get_media_type(hw) == ixgbe_media_type_copper) {
- mac->ops.setup_link = &ixgbe_setup_copper_link_82598;
- mac->ops.setup_link_speed =
- &ixgbe_setup_copper_link_speed_82598;
- mac->ops.get_link_capabilities =
- &ixgbe_get_copper_link_capabilities_82598;
- }
+out:
+ return ret_val;
+}
- mac->mcft_size = IXGBE_82598_MC_TBL_SIZE;
- mac->vft_size = IXGBE_82598_VFT_TBL_SIZE;
- mac->num_rar_entries = IXGBE_82598_RAR_ENTRIES;
- mac->max_rx_queues = IXGBE_82598_MAX_RX_QUEUES;
- mac->max_tx_queues = IXGBE_82598_MAX_TX_QUEUES;
- mac->max_msix_vectors = ixgbe_get_pcie_msix_count_82598(hw);
+/**
+ * ixgbe_start_hw_82598 - Prepare hardware for Tx/Rx
+ * @hw: pointer to hardware structure
+ *
+ * Starts the hardware using the generic start_hw function.
+ * Then set pcie completion timeout
+ **/
+static s32 ixgbe_start_hw_82598(struct ixgbe_hw *hw)
+{
+ s32 ret_val = 0;
+
+ ret_val = ixgbe_start_hw_generic(hw);
+
+ /* set the completion timeout for interface */
+ if (ret_val == 0)
+ ixgbe_set_pcie_completion_timeout(hw);
-out:
return ret_val;
}
bool *autoneg)
{
s32 status = 0;
- s32 autoc_reg;
-
- autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
+ u32 autoc = 0;
- if (hw->mac.link_settings_loaded) {
- autoc_reg &= ~IXGBE_AUTOC_LMS_ATTACH_TYPE;
- autoc_reg &= ~IXGBE_AUTOC_LMS_MASK;
- autoc_reg |= hw->mac.link_attach_type;
- autoc_reg |= hw->mac.link_mode_select;
- }
+ /*
+ * Determine link capabilities based on the stored value of AUTOC,
+ * which represents EEPROM defaults. If AUTOC value has not been
+ * stored, use the current register value.
+ */
+ if (hw->mac.orig_link_settings_stored)
+ autoc = hw->mac.orig_autoc;
+ else
+ autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC);
- switch (autoc_reg & IXGBE_AUTOC_LMS_MASK) {
+ switch (autoc & IXGBE_AUTOC_LMS_MASK) {
case IXGBE_AUTOC_LMS_1G_LINK_NO_AN:
*speed = IXGBE_LINK_SPEED_1GB_FULL;
*autoneg = false;
case IXGBE_AUTOC_LMS_KX4_AN:
case IXGBE_AUTOC_LMS_KX4_AN_1G_AN:
*speed = IXGBE_LINK_SPEED_UNKNOWN;
- if (autoc_reg & IXGBE_AUTOC_KX4_SUPP)
+ if (autoc & IXGBE_AUTOC_KX4_SUPP)
*speed |= IXGBE_LINK_SPEED_10GB_FULL;
- if (autoc_reg & IXGBE_AUTOC_KX_SUPP)
+ if (autoc & IXGBE_AUTOC_KX_SUPP)
*speed |= IXGBE_LINK_SPEED_1GB_FULL;
*autoneg = true;
break;
*speed = 0;
*autoneg = true;
- status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_SPEED_ABILITY,
- IXGBE_MDIO_PMA_PMD_DEV_TYPE,
+ status = hw->phy.ops.read_reg(hw, MDIO_SPEED, MDIO_MMD_PMAPMD,
&speed_ability);
if (status == 0) {
- if (speed_ability & IXGBE_MDIO_PHY_SPEED_10G)
+ if (speed_ability & MDIO_SPEED_10G)
*speed |= IXGBE_LINK_SPEED_10GB_FULL;
- if (speed_ability & IXGBE_MDIO_PHY_SPEED_1G)
+ if (speed_ability & MDIO_PMA_SPEED_1000)
*speed |= IXGBE_LINK_SPEED_1GB_FULL;
}
break;
case IXGBE_DEV_ID_82598AF_DUAL_PORT:
case IXGBE_DEV_ID_82598AF_SINGLE_PORT:
- case IXGBE_DEV_ID_82598EB_CX4:
- case IXGBE_DEV_ID_82598_CX4_DUAL_PORT:
case IXGBE_DEV_ID_82598_DA_DUAL_PORT:
case IXGBE_DEV_ID_82598_SR_DUAL_PORT_EM:
case IXGBE_DEV_ID_82598EB_XF_LR:
case IXGBE_DEV_ID_82598EB_SFP_LOM:
media_type = ixgbe_media_type_fiber;
break;
+ case IXGBE_DEV_ID_82598EB_CX4:
+ case IXGBE_DEV_ID_82598_CX4_DUAL_PORT:
+ media_type = ixgbe_media_type_cx4;
+ break;
case IXGBE_DEV_ID_82598AT:
+ case IXGBE_DEV_ID_82598AT2:
media_type = ixgbe_media_type_copper;
break;
default:
}
/**
- * ixgbe_setup_fc_82598 - Configure flow control settings
+ * ixgbe_fc_enable_82598 - Enable flow control
* @hw: pointer to hardware structure
* @packetbuf_num: packet buffer number (0-7)
*
- * Configures the flow control settings based on SW configuration. This
- * function is used for 802.3x flow control configuration only.
+ * Enable flow control according to the current settings.
**/
-static s32 ixgbe_setup_fc_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
+static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
{
- u32 frctl_reg;
+ s32 ret_val = 0;
+ u32 fctrl_reg;
u32 rmcs_reg;
+ u32 reg;
+ u32 link_speed = 0;
+ bool link_up;
+
+#ifdef CONFIG_DCB
+ if (hw->fc.requested_mode == ixgbe_fc_pfc)
+ goto out;
- if (packetbuf_num < 0 || packetbuf_num > 7) {
- hw_dbg(hw, "Invalid packet buffer number [%d], expected range is"
- " 0-7\n", packetbuf_num);
+#endif /* CONFIG_DCB */
+ /*
+ * On 82598 having Rx FC on causes resets while doing 1G
+ * so if it's on turn it off once we know link_speed. For
+ * more details see 82598 Specification update.
+ */
+ hw->mac.ops.check_link(hw, &link_speed, &link_up, false);
+ if (link_up && link_speed == IXGBE_LINK_SPEED_1GB_FULL) {
+ switch (hw->fc.requested_mode) {
+ case ixgbe_fc_full:
+ hw->fc.requested_mode = ixgbe_fc_tx_pause;
+ break;
+ case ixgbe_fc_rx_pause:
+ hw->fc.requested_mode = ixgbe_fc_none;
+ break;
+ default:
+ /* no change */
+ break;
+ }
}
- frctl_reg = IXGBE_READ_REG(hw, IXGBE_FCTRL);
- frctl_reg &= ~(IXGBE_FCTRL_RFCE | IXGBE_FCTRL_RPFCE);
+ /* Negotiate the fc mode to use */
+ ret_val = ixgbe_fc_autoneg(hw);
+ if (ret_val)
+ goto out;
+
+ /* Disable any previous flow control settings */
+ fctrl_reg = IXGBE_READ_REG(hw, IXGBE_FCTRL);
+ fctrl_reg &= ~(IXGBE_FCTRL_RFCE | IXGBE_FCTRL_RPFCE);
rmcs_reg = IXGBE_READ_REG(hw, IXGBE_RMCS);
rmcs_reg &= ~(IXGBE_RMCS_TFCE_PRIORITY | IXGBE_RMCS_TFCE_802_3X);
/*
- * 10 gig parts do not have a word in the EEPROM to determine the
- * default flow control setting, so we explicitly set it to full.
- */
- if (hw->fc.type == ixgbe_fc_default)
- hw->fc.type = ixgbe_fc_full;
-
- /*
- * We want to save off the original Flow Control configuration just in
- * case we get disconnected and then reconnected into a different hub
- * or switch with different Flow Control capabilities.
- */
- hw->fc.original_type = hw->fc.type;
-
- /*
- * The possible values of the "flow_control" parameter are:
+ * The possible values of fc.current_mode are:
* 0: Flow control is completely disabled
- * 1: Rx flow control is enabled (we can receive pause frames but not
- * send pause frames).
- * 2: Tx flow control is enabled (we can send pause frames but we do not
- * support receiving pause frames)
+ * 1: Rx flow control is enabled (we can receive pause frames,
+ * but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames but
+ * we do not support receiving pause frames).
* 3: Both Rx and Tx flow control (symmetric) are enabled.
* other: Invalid.
+#ifdef CONFIG_DCB
+ * 4: Priority Flow Control is enabled.
+#endif
*/
- switch (hw->fc.type) {
+ switch (hw->fc.current_mode) {
case ixgbe_fc_none:
+ /*
+ * Flow control is disabled by software override or autoneg.
+ * The code below will actually disable it in the HW.
+ */
break;
case ixgbe_fc_rx_pause:
/*
- * Rx Flow control is enabled,
- * and Tx Flow control is disabled.
+ * Rx Flow control is enabled and Tx Flow control is
+ * disabled by software override. Since there really
+ * isn't a way to advertise that we are capable of RX
+ * Pause ONLY, we will advertise that we support both
+ * symmetric and asymmetric Rx PAUSE. Later, we will
+ * disable the adapter's ability to send PAUSE frames.
*/
- frctl_reg |= IXGBE_FCTRL_RFCE;
+ fctrl_reg |= IXGBE_FCTRL_RFCE;
break;
case ixgbe_fc_tx_pause:
/*
- * Tx Flow control is enabled, and Rx Flow control is disabled,
- * by a software over-ride.
+ * Tx Flow control is enabled, and Rx Flow control is
+ * disabled by software override.
*/
rmcs_reg |= IXGBE_RMCS_TFCE_802_3X;
break;
case ixgbe_fc_full:
- /*
- * Flow control (both Rx and Tx) is enabled by a software
- * over-ride.
- */
- frctl_reg |= IXGBE_FCTRL_RFCE;
+ /* Flow control (both Rx and Tx) is enabled by SW override. */
+ fctrl_reg |= IXGBE_FCTRL_RFCE;
rmcs_reg |= IXGBE_RMCS_TFCE_802_3X;
break;
+#ifdef CONFIG_DCB
+ case ixgbe_fc_pfc:
+ goto out;
+ break;
+#endif /* CONFIG_DCB */
default:
- /* We should never get here. The value should be 0-3. */
hw_dbg(hw, "Flow control param set incorrectly\n");
+ ret_val = IXGBE_ERR_CONFIG;
+ goto out;
break;
}
- /* Enable 802.3x based flow control settings. */
- IXGBE_WRITE_REG(hw, IXGBE_FCTRL, frctl_reg);
+ /* Set 802.3x based flow control settings. */
+ fctrl_reg |= IXGBE_FCTRL_DPF;
+ IXGBE_WRITE_REG(hw, IXGBE_FCTRL, fctrl_reg);
IXGBE_WRITE_REG(hw, IXGBE_RMCS, rmcs_reg);
- /*
- * Check for invalid software configuration, zeros are completely
- * invalid for all parameters used past this point, and if we enable
- * flow control with zero water marks, we blast flow control packets.
- */
- if (!hw->fc.low_water || !hw->fc.high_water || !hw->fc.pause_time) {
- hw_dbg(hw, "Flow control structure initialized incorrectly\n");
- return IXGBE_ERR_INVALID_LINK_SETTINGS;
- }
-
- /*
- * We need to set up the Receive Threshold high and low water
- * marks as well as (optionally) enabling the transmission of
- * XON frames.
- */
- if (hw->fc.type & ixgbe_fc_tx_pause) {
+ /* Set up and enable Rx high/low water mark thresholds, enable XON. */
+ if (hw->fc.current_mode & ixgbe_fc_tx_pause) {
if (hw->fc.send_xon) {
IXGBE_WRITE_REG(hw, IXGBE_FCRTL(packetbuf_num),
(hw->fc.low_water | IXGBE_FCRTL_XONE));
IXGBE_WRITE_REG(hw, IXGBE_FCRTL(packetbuf_num),
hw->fc.low_water);
}
+
IXGBE_WRITE_REG(hw, IXGBE_FCRTH(packetbuf_num),
- (hw->fc.high_water)|IXGBE_FCRTH_FCEN);
+ (hw->fc.high_water | IXGBE_FCRTH_FCEN));
}
- IXGBE_WRITE_REG(hw, IXGBE_FCTTV(0), hw->fc.pause_time);
+ /* Configure pause time (2 TCs per register) */
+ reg = IXGBE_READ_REG(hw, IXGBE_FCTTV(packetbuf_num / 2));
+ if ((packetbuf_num & 1) == 0)
+ reg = (reg & 0xFFFF0000) | hw->fc.pause_time;
+ else
+ reg = (reg & 0x0000FFFF) | (hw->fc.pause_time << 16);
+ IXGBE_WRITE_REG(hw, IXGBE_FCTTV(packetbuf_num / 2), reg);
+
IXGBE_WRITE_REG(hw, IXGBE_FCRTV, (hw->fc.pause_time >> 1));
- return 0;
+out:
+ return ret_val;
}
/**
- * ixgbe_setup_mac_link_82598 - Configures MAC link settings
+ * ixgbe_start_mac_link_82598 - Configures MAC link settings
* @hw: pointer to hardware structure
*
* Configures link settings based on values in the ixgbe_hw struct.
* Restarts the link. Performs autonegotiation if needed.
**/
-static s32 ixgbe_setup_mac_link_82598(struct ixgbe_hw *hw)
+static s32 ixgbe_start_mac_link_82598(struct ixgbe_hw *hw,
+ bool autoneg_wait_to_complete)
{
u32 autoc_reg;
u32 links_reg;
u32 i;
s32 status = 0;
- autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
-
- if (hw->mac.link_settings_loaded) {
- autoc_reg &= ~IXGBE_AUTOC_LMS_ATTACH_TYPE;
- autoc_reg &= ~IXGBE_AUTOC_LMS_MASK;
- autoc_reg |= hw->mac.link_attach_type;
- autoc_reg |= hw->mac.link_mode_select;
-
- IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg);
- IXGBE_WRITE_FLUSH(hw);
- msleep(50);
- }
-
/* Restart link */
+ autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
autoc_reg |= IXGBE_AUTOC_AN_RESTART;
IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg);
/* Only poll for autoneg to complete if specified to do so */
- if (hw->phy.autoneg_wait_to_complete) {
- if (hw->mac.link_mode_select == IXGBE_AUTOC_LMS_KX4_AN ||
- hw->mac.link_mode_select == IXGBE_AUTOC_LMS_KX4_AN_1G_AN) {
+ if (autoneg_wait_to_complete) {
+ if ((autoc_reg & IXGBE_AUTOC_LMS_MASK) ==
+ IXGBE_AUTOC_LMS_KX4_AN ||
+ (autoc_reg & IXGBE_AUTOC_LMS_MASK) ==
+ IXGBE_AUTOC_LMS_KX4_AN_1G_AN) {
links_reg = 0; /* Just in case Autoneg time = 0 */
for (i = 0; i < IXGBE_AUTO_NEG_TIME; i++) {
links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS);
}
}
- /*
- * We want to save off the original Flow Control configuration just in
- * case we get disconnected and then reconnected into a different hub
- * or switch with different Flow Control capabilities.
- */
- hw->fc.original_type = hw->fc.type;
- ixgbe_setup_fc_82598(hw, 0);
-
/* Add delay to filter out noises during initial link setup */
msleep(50);
}
/**
+ * ixgbe_validate_link_ready - Function looks for phy link
+ * @hw: pointer to hardware structure
+ *
+ * Function indicates success when phy link is available. If phy is not ready
+ * within 5 seconds of MAC indicating link, the function returns error.
+ **/
+static s32 ixgbe_validate_link_ready(struct ixgbe_hw *hw)
+{
+ u32 timeout;
+ u16 an_reg;
+
+ if (hw->device_id != IXGBE_DEV_ID_82598AT2)
+ return 0;
+
+ for (timeout = 0;
+ timeout < IXGBE_VALIDATE_LINK_READY_TIMEOUT; timeout++) {
+ hw->phy.ops.read_reg(hw, MDIO_STAT1, MDIO_MMD_AN, &an_reg);
+
+ if ((an_reg & MDIO_AN_STAT1_COMPLETE) &&
+ (an_reg & MDIO_STAT1_LSTATUS))
+ break;
+
+ msleep(100);
+ }
+
+ if (timeout == IXGBE_VALIDATE_LINK_READY_TIMEOUT) {
+ hw_dbg(hw, "Link was indicated but link is down\n");
+ return IXGBE_ERR_LINK_SETUP;
+ }
+
+ return 0;
+}
+
+/**
* ixgbe_check_mac_link_82598 - Get link/speed status
* @hw: pointer to hardware structure
* @speed: pointer to link speed
* clear indicates active; set indicates inactive.
*/
if (hw->phy.type == ixgbe_phy_nl) {
- hw->phy.ops.read_reg(hw, 0xC79F, IXGBE_TWINAX_DEV, &link_reg);
- hw->phy.ops.read_reg(hw, 0xC79F, IXGBE_TWINAX_DEV, &link_reg);
- hw->phy.ops.read_reg(hw, 0xC00C, IXGBE_TWINAX_DEV,
+ hw->phy.ops.read_reg(hw, 0xC79F, MDIO_MMD_PMAPMD, &link_reg);
+ hw->phy.ops.read_reg(hw, 0xC79F, MDIO_MMD_PMAPMD, &link_reg);
+ hw->phy.ops.read_reg(hw, 0xC00C, MDIO_MMD_PMAPMD,
&adapt_comp_reg);
if (link_up_wait_to_complete) {
for (i = 0; i < IXGBE_LINK_UP_TIME; i++) {
}
msleep(100);
hw->phy.ops.read_reg(hw, 0xC79F,
- IXGBE_TWINAX_DEV,
+ MDIO_MMD_PMAPMD,
&link_reg);
hw->phy.ops.read_reg(hw, 0xC00C,
- IXGBE_TWINAX_DEV,
+ MDIO_MMD_PMAPMD,
&adapt_comp_reg);
}
} else {
else
*speed = IXGBE_LINK_SPEED_1GB_FULL;
+ if ((hw->device_id == IXGBE_DEV_ID_82598AT2) && (*link_up == true) &&
+ (ixgbe_validate_link_ready(hw) != 0))
+ *link_up = false;
+
+ /* if link is down, zero out the current_mode */
+ if (*link_up == false) {
+ hw->fc.current_mode = ixgbe_fc_none;
+ hw->fc.fc_was_autonegged = false;
+ }
out:
return 0;
}
/**
- * ixgbe_setup_mac_link_speed_82598 - Set MAC link speed
+ * ixgbe_setup_mac_link_82598 - Set MAC link speed
* @hw: pointer to hardware structure
* @speed: new link speed
* @autoneg: true if auto-negotiation enabled
*
* Set the link speed in the AUTOC register and restarts link.
**/
-static s32 ixgbe_setup_mac_link_speed_82598(struct ixgbe_hw *hw,
- ixgbe_link_speed speed, bool autoneg,
- bool autoneg_wait_to_complete)
+static s32 ixgbe_setup_mac_link_82598(struct ixgbe_hw *hw,
+ ixgbe_link_speed speed, bool autoneg,
+ bool autoneg_wait_to_complete)
{
- s32 status = 0;
+ s32 status = 0;
+ ixgbe_link_speed link_capabilities = IXGBE_LINK_SPEED_UNKNOWN;
+ u32 curr_autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC);
+ u32 autoc = curr_autoc;
+ u32 link_mode = autoc & IXGBE_AUTOC_LMS_MASK;
- /* If speed is 10G, then check for CX4 or XAUI. */
- if ((speed == IXGBE_LINK_SPEED_10GB_FULL) &&
- (!(hw->mac.link_attach_type & IXGBE_AUTOC_10G_KX4))) {
- hw->mac.link_mode_select = IXGBE_AUTOC_LMS_10G_LINK_NO_AN;
- } else if ((speed == IXGBE_LINK_SPEED_1GB_FULL) && (!autoneg)) {
- hw->mac.link_mode_select = IXGBE_AUTOC_LMS_1G_LINK_NO_AN;
- } else if (autoneg) {
- /* BX mode - Autonegotiate 1G */
- if (!(hw->mac.link_attach_type & IXGBE_AUTOC_1G_PMA_PMD))
- hw->mac.link_mode_select = IXGBE_AUTOC_LMS_1G_AN;
- else /* KX/KX4 mode */
- hw->mac.link_mode_select = IXGBE_AUTOC_LMS_KX4_AN_1G_AN;
- } else {
+ /* Check to see if speed passed in is supported. */
+ ixgbe_get_link_capabilities_82598(hw, &link_capabilities, &autoneg);
+ speed &= link_capabilities;
+
+ if (speed == IXGBE_LINK_SPEED_UNKNOWN)
status = IXGBE_ERR_LINK_SETUP;
+
+ /* Set KX4/KX support according to speed requested */
+ else if (link_mode == IXGBE_AUTOC_LMS_KX4_AN ||
+ link_mode == IXGBE_AUTOC_LMS_KX4_AN_1G_AN) {
+ autoc &= ~IXGBE_AUTOC_KX4_KX_SUPP_MASK;
+ if (speed & IXGBE_LINK_SPEED_10GB_FULL)
+ autoc |= IXGBE_AUTOC_KX4_SUPP;
+ if (speed & IXGBE_LINK_SPEED_1GB_FULL)
+ autoc |= IXGBE_AUTOC_KX_SUPP;
+ if (autoc != curr_autoc)
+ IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc);
}
if (status == 0) {
- hw->phy.autoneg_wait_to_complete = autoneg_wait_to_complete;
-
- hw->mac.link_settings_loaded = true;
/*
* Setup and restart the link based on the new values in
* ixgbe_hw This will write the AUTOC register based on the new
* stored values
*/
- ixgbe_setup_mac_link_82598(hw);
+ status = ixgbe_start_mac_link_82598(hw, autoneg_wait_to_complete);
}
return status;
/**
- * ixgbe_setup_copper_link_82598 - Setup copper link settings
- * @hw: pointer to hardware structure
- *
- * Configures link settings based on values in the ixgbe_hw struct.
- * Restarts the link. Performs autonegotiation if needed. Restart
- * phy and wait for autonegotiate to finish. Then synchronize the
- * MAC and PHY.
- **/
-static s32 ixgbe_setup_copper_link_82598(struct ixgbe_hw *hw)
-{
- s32 status;
-
- /* Restart autonegotiation on PHY */
- status = hw->phy.ops.setup_link(hw);
-
- /* Set MAC to KX/KX4 autoneg, which defaults to Parallel detection */
- hw->mac.link_attach_type = (IXGBE_AUTOC_10G_KX4 | IXGBE_AUTOC_1G_KX);
- hw->mac.link_mode_select = IXGBE_AUTOC_LMS_KX4_AN;
-
- /* Set up MAC */
- ixgbe_setup_mac_link_82598(hw);
-
- return status;
-}
-
-/**
- * ixgbe_setup_copper_link_speed_82598 - Set the PHY autoneg advertised field
+ * ixgbe_setup_copper_link_82598 - Set the PHY autoneg advertised field
* @hw: pointer to hardware structure
* @speed: new link speed
* @autoneg: true if autonegotiation enabled
*
* Sets the link speed in the AUTOC register in the MAC and restarts link.
**/
-static s32 ixgbe_setup_copper_link_speed_82598(struct ixgbe_hw *hw,
+static s32 ixgbe_setup_copper_link_82598(struct ixgbe_hw *hw,
ixgbe_link_speed speed,
bool autoneg,
bool autoneg_wait_to_complete)
status = hw->phy.ops.setup_link_speed(hw, speed, autoneg,
autoneg_wait_to_complete);
- /* Set MAC to KX/KX4 autoneg, which defaults to Parallel detection */
- hw->mac.link_attach_type = (IXGBE_AUTOC_10G_KX4 | IXGBE_AUTOC_1G_KX);
- hw->mac.link_mode_select = IXGBE_AUTOC_LMS_KX4_AN;
-
/* Set up MAC */
- ixgbe_setup_mac_link_82598(hw);
+ ixgbe_start_mac_link_82598(hw, autoneg_wait_to_complete);
return status;
}
static s32 ixgbe_reset_hw_82598(struct ixgbe_hw *hw)
{
s32 status = 0;
+ s32 phy_status = 0;
u32 ctrl;
u32 gheccr;
u32 i;
}
/* Reset PHY */
- if (hw->phy.reset_disable == false)
+ if (hw->phy.reset_disable == false) {
+ /* PHY ops must be identified and initialized prior to reset */
+
+ /* Init PHY and function pointers, perform SFP setup */
+ phy_status = hw->phy.ops.init(hw);
+ if (phy_status == IXGBE_ERR_SFP_NOT_SUPPORTED)
+ goto reset_hw_out;
+ else if (phy_status == IXGBE_ERR_SFP_NOT_PRESENT)
+ goto no_phy_reset;
+
+
hw->phy.ops.reset(hw);
+ }
+no_phy_reset:
/*
* Prevent the PCI-E bus from from hanging by disabling PCI-E master
* access and verify no pending requests before reset
*/
- if (ixgbe_disable_pcie_master(hw) != 0) {
+ status = ixgbe_disable_pcie_master(hw);
+ if (status != 0) {
status = IXGBE_ERR_MASTER_REQUESTS_PENDING;
hw_dbg(hw, "PCI-E Master disable polling has failed.\n");
}
IXGBE_WRITE_REG(hw, IXGBE_GHECCR, gheccr);
/*
- * AUTOC register which stores link settings gets cleared
- * and reloaded from EEPROM after reset. We need to restore
- * our stored value from init in case SW changed the attach
- * type or speed. If this is the first time and link settings
- * have not been stored, store default settings from AUTOC.
+ * Store the original AUTOC value if it has not been
+ * stored off yet. Otherwise restore the stored original
+ * AUTOC value since the reset operation sets back to deaults.
*/
autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC);
- if (hw->mac.link_settings_loaded) {
- autoc &= ~(IXGBE_AUTOC_LMS_ATTACH_TYPE);
- autoc &= ~(IXGBE_AUTOC_LMS_MASK);
- autoc |= hw->mac.link_attach_type;
- autoc |= hw->mac.link_mode_select;
- IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc);
- } else {
- hw->mac.link_attach_type =
- (autoc & IXGBE_AUTOC_LMS_ATTACH_TYPE);
- hw->mac.link_mode_select = (autoc & IXGBE_AUTOC_LMS_MASK);
- hw->mac.link_settings_loaded = true;
+ if (hw->mac.orig_link_settings_stored == false) {
+ hw->mac.orig_autoc = autoc;
+ hw->mac.orig_link_settings_stored = true;
+ } else if (autoc != hw->mac.orig_autoc) {
+ IXGBE_WRITE_REG(hw, IXGBE_AUTOC, hw->mac.orig_autoc);
}
+ /*
+ * Store MAC address from RAR0, clear receive address registers, and
+ * clear the multicast table
+ */
+ hw->mac.ops.init_rx_addrs(hw);
+
/* Store the permanent mac address */
hw->mac.ops.get_mac_addr(hw, hw->mac.perm_addr);
+reset_hw_out:
+ if (phy_status)
+ status = phy_status;
+
return status;
}
}
/**
- * ixgbe_blink_led_start_82598 - Blink LED based on index.
- * @hw: pointer to hardware structure
- * @index: led number to blink
- **/
-static s32 ixgbe_blink_led_start_82598(struct ixgbe_hw *hw, u32 index)
-{
- ixgbe_link_speed speed = 0;
- bool link_up = 0;
- u32 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
- u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
-
- /*
- * Link must be up to auto-blink the LEDs on the 82598EB MAC;
- * force it if link is down.
- */
- hw->mac.ops.check_link(hw, &speed, &link_up, false);
-
- if (!link_up) {
- autoc_reg |= IXGBE_AUTOC_FLU;
- IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg);
- msleep(10);
- }
-
- led_reg &= ~IXGBE_LED_MODE_MASK(index);
- led_reg |= IXGBE_LED_BLINK(index);
- IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
- IXGBE_WRITE_FLUSH(hw);
-
- return 0;
-}
-
-/**
- * ixgbe_blink_led_stop_82598 - Stop blinking LED based on index.
- * @hw: pointer to hardware structure
- * @index: led number to stop blinking
- **/
-static s32 ixgbe_blink_led_stop_82598(struct ixgbe_hw *hw, u32 index)
-{
- u32 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
- u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
-
- autoc_reg &= ~IXGBE_AUTOC_FLU;
- autoc_reg |= IXGBE_AUTOC_AN_RESTART;
- IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg);
-
- led_reg &= ~IXGBE_LED_MODE_MASK(index);
- led_reg &= ~IXGBE_LED_BLINK(index);
- led_reg |= IXGBE_LED_LINK_ACTIVE << IXGBE_LED_MODE_SHIFT(index);
- IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
- IXGBE_WRITE_FLUSH(hw);
-
- return 0;
-}
-
-/**
* ixgbe_read_analog_reg8_82598 - Reads 8 bit Atlas analog register
* @hw: pointer to hardware structure
* @reg: analog register to read
sfp_addr = (sfp_addr | IXGBE_I2C_EEPROM_READ_MASK);
hw->phy.ops.write_reg(hw,
IXGBE_MDIO_PMA_PMD_SDA_SCL_ADDR,
- IXGBE_MDIO_PMA_PMD_DEV_TYPE,
+ MDIO_MMD_PMAPMD,
sfp_addr);
/* Poll status */
for (i = 0; i < 100; i++) {
hw->phy.ops.read_reg(hw,
IXGBE_MDIO_PMA_PMD_SDA_SCL_STAT,
- IXGBE_MDIO_PMA_PMD_DEV_TYPE,
+ MDIO_MMD_PMAPMD,
&sfp_stat);
sfp_stat = sfp_stat & IXGBE_I2C_EEPROM_STATUS_MASK;
if (sfp_stat != IXGBE_I2C_EEPROM_STATUS_IN_PROGRESS)
/* Read data */
hw->phy.ops.read_reg(hw, IXGBE_MDIO_PMA_PMD_SDA_SCL_DATA,
- IXGBE_MDIO_PMA_PMD_DEV_TYPE, &sfp_data);
+ MDIO_MMD_PMAPMD, &sfp_data);
*eeprom_data = (u8)(sfp_data >> 8);
} else {
*
* Determines physical layer capabilities of the current configuration.
**/
-static s32 ixgbe_get_supported_physical_layer_82598(struct ixgbe_hw *hw)
+static u32 ixgbe_get_supported_physical_layer_82598(struct ixgbe_hw *hw)
{
- s32 physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN;
+ u32 physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN;
+ u32 autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC);
+ u32 pma_pmd_10g = autoc & IXGBE_AUTOC_10G_PMA_PMD_MASK;
+ u32 pma_pmd_1g = autoc & IXGBE_AUTOC_1G_PMA_PMD_MASK;
+ u16 ext_ability = 0;
+
+ hw->phy.ops.identify(hw);
+
+ /* Copper PHY must be checked before AUTOC LMS to determine correct
+ * physical layer because 10GBase-T PHYs use LMS = KX4/KX */
+ if (hw->phy.type == ixgbe_phy_tn ||
+ hw->phy.type == ixgbe_phy_cu_unknown) {
+ hw->phy.ops.read_reg(hw, MDIO_PMA_EXTABLE, MDIO_MMD_PMAPMD,
+ &ext_ability);
+ if (ext_ability & MDIO_PMA_EXTABLE_10GBT)
+ physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_T;
+ if (ext_ability & MDIO_PMA_EXTABLE_1000BT)
+ physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_T;
+ if (ext_ability & MDIO_PMA_EXTABLE_100BTX)
+ physical_layer |= IXGBE_PHYSICAL_LAYER_100BASE_TX;
+ goto out;
+ }
- switch (hw->device_id) {
- case IXGBE_DEV_ID_82598:
- /* Default device ID is mezzanine card KX/KX4 */
- physical_layer = (IXGBE_PHYSICAL_LAYER_10GBASE_KX4 |
- IXGBE_PHYSICAL_LAYER_1000BASE_KX);
- break;
- case IXGBE_DEV_ID_82598_BX:
- physical_layer = IXGBE_PHYSICAL_LAYER_1000BASE_BX;
- case IXGBE_DEV_ID_82598EB_CX4:
- case IXGBE_DEV_ID_82598_CX4_DUAL_PORT:
- physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_CX4;
- break;
- case IXGBE_DEV_ID_82598_DA_DUAL_PORT:
- physical_layer = IXGBE_PHYSICAL_LAYER_SFP_PLUS_CU;
+ switch (autoc & IXGBE_AUTOC_LMS_MASK) {
+ case IXGBE_AUTOC_LMS_1G_AN:
+ case IXGBE_AUTOC_LMS_1G_LINK_NO_AN:
+ if (pma_pmd_1g == IXGBE_AUTOC_1G_KX)
+ physical_layer = IXGBE_PHYSICAL_LAYER_1000BASE_KX;
+ else
+ physical_layer = IXGBE_PHYSICAL_LAYER_1000BASE_BX;
break;
- case IXGBE_DEV_ID_82598AF_DUAL_PORT:
- case IXGBE_DEV_ID_82598AF_SINGLE_PORT:
- case IXGBE_DEV_ID_82598_SR_DUAL_PORT_EM:
- physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_SR;
+ case IXGBE_AUTOC_LMS_10G_LINK_NO_AN:
+ if (pma_pmd_10g == IXGBE_AUTOC_10G_CX4)
+ physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_CX4;
+ else if (pma_pmd_10g == IXGBE_AUTOC_10G_KX4)
+ physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_KX4;
+ else /* XAUI */
+ physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN;
break;
- case IXGBE_DEV_ID_82598EB_XF_LR:
- physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_LR;
+ case IXGBE_AUTOC_LMS_KX4_AN:
+ case IXGBE_AUTOC_LMS_KX4_AN_1G_AN:
+ if (autoc & IXGBE_AUTOC_KX_SUPP)
+ physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_KX;
+ if (autoc & IXGBE_AUTOC_KX4_SUPP)
+ physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_KX4;
break;
- case IXGBE_DEV_ID_82598AT:
- physical_layer = (IXGBE_PHYSICAL_LAYER_10GBASE_T |
- IXGBE_PHYSICAL_LAYER_1000BASE_T);
+ default:
break;
- case IXGBE_DEV_ID_82598EB_SFP_LOM:
+ }
+
+ if (hw->phy.type == ixgbe_phy_nl) {
hw->phy.ops.identify_sfp(hw);
switch (hw->phy.sfp_type) {
physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN;
break;
}
- break;
+ }
+ switch (hw->device_id) {
+ case IXGBE_DEV_ID_82598_DA_DUAL_PORT:
+ physical_layer = IXGBE_PHYSICAL_LAYER_SFP_PLUS_CU;
+ break;
+ case IXGBE_DEV_ID_82598AF_DUAL_PORT:
+ case IXGBE_DEV_ID_82598AF_SINGLE_PORT:
+ case IXGBE_DEV_ID_82598_SR_DUAL_PORT_EM:
+ physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_SR;
+ break;
+ case IXGBE_DEV_ID_82598EB_XF_LR:
+ physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_LR;
+ break;
default:
- physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN;
break;
}
+out:
return physical_layer;
}
static struct ixgbe_mac_operations mac_ops_82598 = {
.init_hw = &ixgbe_init_hw_generic,
.reset_hw = &ixgbe_reset_hw_82598,
- .start_hw = &ixgbe_start_hw_generic,
+ .start_hw = &ixgbe_start_hw_82598,
.clear_hw_cntrs = &ixgbe_clear_hw_cntrs_generic,
.get_media_type = &ixgbe_get_media_type_82598,
.get_supported_physical_layer = &ixgbe_get_supported_physical_layer_82598,
+ .enable_rx_dma = &ixgbe_enable_rx_dma_generic,
.get_mac_addr = &ixgbe_get_mac_addr_generic,
.stop_adapter = &ixgbe_stop_adapter_generic,
+ .get_bus_info = &ixgbe_get_bus_info_generic,
+ .set_lan_id = &ixgbe_set_lan_id_multi_port_pcie,
.read_analog_reg8 = &ixgbe_read_analog_reg8_82598,
.write_analog_reg8 = &ixgbe_write_analog_reg8_82598,
.setup_link = &ixgbe_setup_mac_link_82598,
- .setup_link_speed = &ixgbe_setup_mac_link_speed_82598,
.check_link = &ixgbe_check_mac_link_82598,
.get_link_capabilities = &ixgbe_get_link_capabilities_82598,
.led_on = &ixgbe_led_on_generic,
.led_off = &ixgbe_led_off_generic,
- .blink_led_start = &ixgbe_blink_led_start_82598,
- .blink_led_stop = &ixgbe_blink_led_stop_82598,
+ .blink_led_start = &ixgbe_blink_led_start_generic,
+ .blink_led_stop = &ixgbe_blink_led_stop_generic,
.set_rar = &ixgbe_set_rar_generic,
.clear_rar = &ixgbe_clear_rar_generic,
.set_vmdq = &ixgbe_set_vmdq_82598,
.disable_mc = &ixgbe_disable_mc_generic,
.clear_vfta = &ixgbe_clear_vfta_82598,
.set_vfta = &ixgbe_set_vfta_82598,
- .setup_fc = &ixgbe_setup_fc_82598,
+ .fc_enable = &ixgbe_fc_enable_82598,
};
static struct ixgbe_eeprom_operations eeprom_ops_82598 = {
.init_params = &ixgbe_init_eeprom_params_generic,
- .read = &ixgbe_read_eeprom_generic,
+ .read = &ixgbe_read_eerd_generic,
.validate_checksum = &ixgbe_validate_eeprom_checksum_generic,
.update_checksum = &ixgbe_update_eeprom_checksum_generic,
};
static struct ixgbe_phy_operations phy_ops_82598 = {
.identify = &ixgbe_identify_phy_generic,
.identify_sfp = &ixgbe_identify_sfp_module_generic,
+ .init = &ixgbe_init_phy_ops_82598,
.reset = &ixgbe_reset_phy_generic,
.read_reg = &ixgbe_read_phy_reg_generic,
.write_reg = &ixgbe_write_phy_reg_generic,
.setup_link = &ixgbe_setup_phy_link_generic,
.setup_link_speed = &ixgbe_setup_phy_link_speed_generic,
.read_i2c_eeprom = &ixgbe_read_i2c_eeprom_82598,
+ .check_overtemp = &ixgbe_tn_check_overtemp,
};
struct ixgbe_info ixgbe_82598_info = {
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff