/*******************************************************************************
Intel 10 Gigabit PCI Express Linux driver
- Copyright(c) 1999 - 2007 Intel Corporation.
+ Copyright(c) 1999 - 2010 Intel Corporation.
This program is free software; you can redistribute it and/or modify it
under the terms and conditions of the GNU General Public License,
the file called "COPYING".
Contact Information:
- Linux NICS <linux.nics@intel.com>
e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
#define IXGBE_82598_MC_TBL_SIZE 128
#define IXGBE_82598_VFT_TBL_SIZE 128
-static s32 ixgbe_get_invariants_82598(struct ixgbe_hw *hw);
-static s32 ixgbe_get_link_settings_82598(struct ixgbe_hw *hw, u32 *speed,
- bool *autoneg);
-static s32 ixgbe_get_copper_link_settings_82598(struct ixgbe_hw *hw,
- u32 *speed, bool *autoneg);
-static enum ixgbe_media_type ixgbe_get_media_type_82598(struct ixgbe_hw *hw);
-static s32 ixgbe_setup_mac_link_82598(struct ixgbe_hw *hw);
-static s32 ixgbe_check_mac_link_82598(struct ixgbe_hw *hw, u32 *speed,
- bool *link_up,
- bool link_up_wait_to_complete);
-static s32 ixgbe_setup_mac_link_speed_82598(struct ixgbe_hw *hw, u32 speed,
- bool autoneg,
- bool autoneg_wait_to_complete);
-static s32 ixgbe_setup_copper_link_82598(struct ixgbe_hw *hw);
-static s32 ixgbe_setup_copper_link_speed_82598(struct ixgbe_hw *hw, u32 speed,
- bool autoneg,
- bool autoneg_wait_to_complete);
-static s32 ixgbe_reset_hw_82598(struct ixgbe_hw *hw);
+static s32 ixgbe_get_copper_link_capabilities_82598(struct ixgbe_hw *hw,
+ ixgbe_link_speed *speed,
+ bool *autoneg);
+static s32 ixgbe_setup_copper_link_82598(struct ixgbe_hw *hw,
+ ixgbe_link_speed speed,
+ bool autoneg,
+ bool autoneg_wait_to_complete);
+static s32 ixgbe_read_i2c_eeprom_82598(struct ixgbe_hw *hw, u8 byte_offset,
+ u8 *eeprom_data);
+/**
+ * ixgbe_set_pcie_completion_timeout - set pci-e completion timeout
+ * @hw: pointer to the HW structure
+ *
+ * The defaults for 82598 should be in the range of 50us to 50ms,
+ * however the hardware default for these parts is 500us to 1ms which is less
+ * than the 10ms recommended by the pci-e spec. To address this we need to
+ * increase the value to either 10ms to 250ms for capability version 1 config,
+ * or 16ms to 55ms for version 2.
+ **/
+static void ixgbe_set_pcie_completion_timeout(struct ixgbe_hw *hw)
+{
+ struct ixgbe_adapter *adapter = hw->back;
+ u32 gcr = IXGBE_READ_REG(hw, IXGBE_GCR);
+ u16 pcie_devctl2;
+
+ /* only take action if timeout value is defaulted to 0 */
+ if (gcr & IXGBE_GCR_CMPL_TMOUT_MASK)
+ goto out;
+
+ /*
+ * if capababilities version is type 1 we can write the
+ * timeout of 10ms to 250ms through the GCR register
+ */
+ if (!(gcr & IXGBE_GCR_CAP_VER2)) {
+ gcr |= IXGBE_GCR_CMPL_TMOUT_10ms;
+ goto out;
+ }
+
+ /*
+ * for version 2 capabilities we need to write the config space
+ * directly in order to set the completion timeout value for
+ * 16ms to 55ms
+ */
+ pci_read_config_word(adapter->pdev,
+ IXGBE_PCI_DEVICE_CONTROL2, &pcie_devctl2);
+ pcie_devctl2 |= IXGBE_PCI_DEVICE_CONTROL2_16ms;
+ pci_write_config_word(adapter->pdev,
+ IXGBE_PCI_DEVICE_CONTROL2, pcie_devctl2);
+out:
+ /* disable completion timeout resend */
+ gcr &= ~IXGBE_GCR_CMPL_TMOUT_RESEND;
+ IXGBE_WRITE_REG(hw, IXGBE_GCR, gcr);
+}
+
+/**
+ * ixgbe_get_pcie_msix_count_82598 - Gets MSI-X vector count
+ * @hw: pointer to hardware structure
+ *
+ * Read PCIe configuration space, and get the MSI-X vector count from
+ * the capabilities table.
+ **/
+static u16 ixgbe_get_pcie_msix_count_82598(struct ixgbe_hw *hw)
+{
+ struct ixgbe_adapter *adapter = hw->back;
+ u16 msix_count;
+ pci_read_config_word(adapter->pdev, IXGBE_PCIE_MSIX_82598_CAPS,
+ &msix_count);
+ msix_count &= IXGBE_PCIE_MSIX_TBL_SZ_MASK;
+
+ /* MSI-X count is zero-based in HW, so increment to give proper value */
+ msix_count++;
+ return msix_count;
+}
+
+/**
+ */
static s32 ixgbe_get_invariants_82598(struct ixgbe_hw *hw)
{
- hw->mac.num_rx_queues = IXGBE_82598_MAX_RX_QUEUES;
- hw->mac.num_tx_queues = IXGBE_82598_MAX_TX_QUEUES;
- hw->mac.mcft_size = IXGBE_82598_MC_TBL_SIZE;
- hw->mac.vft_size = IXGBE_82598_VFT_TBL_SIZE;
- hw->mac.num_rar_entries = IXGBE_82598_RAR_ENTRIES;
-
- /* PHY ops are filled in by default properly for Fiber only */
- if (hw->mac.ops.get_media_type(hw) == ixgbe_media_type_copper) {
- hw->mac.ops.setup_link = &ixgbe_setup_copper_link_82598;
- hw->mac.ops.setup_link_speed = &ixgbe_setup_copper_link_speed_82598;
- hw->mac.ops.get_link_settings =
- &ixgbe_get_copper_link_settings_82598;
-
- /* Call PHY identify routine to get the phy type */
- ixgbe_identify_phy(hw);
-
- switch (hw->phy.type) {
- case ixgbe_phy_tn:
- hw->phy.ops.setup_link = &ixgbe_setup_tnx_phy_link;
- hw->phy.ops.check_link = &ixgbe_check_tnx_phy_link;
- hw->phy.ops.setup_link_speed =
- &ixgbe_setup_tnx_phy_link_speed;
- break;
- default:
- break;
+ struct ixgbe_mac_info *mac = &hw->mac;
+
+ /* Call PHY identify routine to get the phy type */
+ ixgbe_identify_phy_generic(hw);
+
+ mac->mcft_size = IXGBE_82598_MC_TBL_SIZE;
+ mac->vft_size = IXGBE_82598_VFT_TBL_SIZE;
+ mac->num_rar_entries = IXGBE_82598_RAR_ENTRIES;
+ mac->max_rx_queues = IXGBE_82598_MAX_RX_QUEUES;
+ mac->max_tx_queues = IXGBE_82598_MAX_TX_QUEUES;
+ mac->max_msix_vectors = ixgbe_get_pcie_msix_count_82598(hw);
+
+ return 0;
+}
+
+/**
+ * ixgbe_init_phy_ops_82598 - PHY/SFP specific init
+ * @hw: pointer to hardware structure
+ *
+ * Initialize any function pointers that were not able to be
+ * set during get_invariants because the PHY/SFP type was
+ * not known. Perform the SFP init if necessary.
+ *
+ **/
+static s32 ixgbe_init_phy_ops_82598(struct ixgbe_hw *hw)
+{
+ struct ixgbe_mac_info *mac = &hw->mac;
+ struct ixgbe_phy_info *phy = &hw->phy;
+ s32 ret_val = 0;
+ u16 list_offset, data_offset;
+
+ /* Identify the PHY */
+ phy->ops.identify(hw);
+
+ /* Overwrite the link function pointers if copper PHY */
+ if (mac->ops.get_media_type(hw) == ixgbe_media_type_copper) {
+ mac->ops.setup_link = &ixgbe_setup_copper_link_82598;
+ mac->ops.get_link_capabilities =
+ &ixgbe_get_copper_link_capabilities_82598;
+ }
+
+ switch (hw->phy.type) {
+ case ixgbe_phy_tn:
+ phy->ops.check_link = &ixgbe_check_phy_link_tnx;
+ phy->ops.get_firmware_version =
+ &ixgbe_get_phy_firmware_version_tnx;
+ break;
+ case ixgbe_phy_nl:
+ phy->ops.reset = &ixgbe_reset_phy_nl;
+
+ /* Call SFP+ identify routine to get the SFP+ module type */
+ ret_val = phy->ops.identify_sfp(hw);
+ if (ret_val != 0)
+ goto out;
+ else if (hw->phy.sfp_type == ixgbe_sfp_type_unknown) {
+ ret_val = IXGBE_ERR_SFP_NOT_SUPPORTED;
+ goto out;
}
+
+ /* Check to see if SFP+ module is supported */
+ ret_val = ixgbe_get_sfp_init_sequence_offsets(hw,
+ &list_offset,
+ &data_offset);
+ if (ret_val != 0) {
+ ret_val = IXGBE_ERR_SFP_NOT_SUPPORTED;
+ goto out;
+ }
+ break;
+ default:
+ break;
}
- return 0;
+out:
+ return ret_val;
+}
+
+/**
+ * ixgbe_start_hw_82598 - Prepare hardware for Tx/Rx
+ * @hw: pointer to hardware structure
+ *
+ * Starts the hardware using the generic start_hw function.
+ * Then set pcie completion timeout
+ **/
+static s32 ixgbe_start_hw_82598(struct ixgbe_hw *hw)
+{
+ s32 ret_val = 0;
+
+ ret_val = ixgbe_start_hw_generic(hw);
+
+ /* set the completion timeout for interface */
+ if (ret_val == 0)
+ ixgbe_set_pcie_completion_timeout(hw);
+
+ return ret_val;
}
/**
- * ixgbe_get_link_settings_82598 - Determines default link settings
+ * ixgbe_get_link_capabilities_82598 - Determines link capabilities
* @hw: pointer to hardware structure
* @speed: pointer to link speed
* @autoneg: boolean auto-negotiation value
*
- * Determines the default link settings by reading the AUTOC register.
+ * Determines the link capabilities by reading the AUTOC register.
**/
-static s32 ixgbe_get_link_settings_82598(struct ixgbe_hw *hw, u32 *speed,
- bool *autoneg)
+static s32 ixgbe_get_link_capabilities_82598(struct ixgbe_hw *hw,
+ ixgbe_link_speed *speed,
+ bool *autoneg)
{
s32 status = 0;
- s32 autoc_reg;
-
- autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
+ u32 autoc = 0;
- if (hw->mac.link_settings_loaded) {
- autoc_reg &= ~IXGBE_AUTOC_LMS_ATTACH_TYPE;
- autoc_reg &= ~IXGBE_AUTOC_LMS_MASK;
- autoc_reg |= hw->mac.link_attach_type;
- autoc_reg |= hw->mac.link_mode_select;
- }
+ /*
+ * Determine link capabilities based on the stored value of AUTOC,
+ * which represents EEPROM defaults. If AUTOC value has not been
+ * stored, use the current register value.
+ */
+ if (hw->mac.orig_link_settings_stored)
+ autoc = hw->mac.orig_autoc;
+ else
+ autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC);
- switch (autoc_reg & IXGBE_AUTOC_LMS_MASK) {
+ switch (autoc & IXGBE_AUTOC_LMS_MASK) {
case IXGBE_AUTOC_LMS_1G_LINK_NO_AN:
*speed = IXGBE_LINK_SPEED_1GB_FULL;
*autoneg = false;
case IXGBE_AUTOC_LMS_KX4_AN:
case IXGBE_AUTOC_LMS_KX4_AN_1G_AN:
*speed = IXGBE_LINK_SPEED_UNKNOWN;
- if (autoc_reg & IXGBE_AUTOC_KX4_SUPP)
+ if (autoc & IXGBE_AUTOC_KX4_SUPP)
*speed |= IXGBE_LINK_SPEED_10GB_FULL;
- if (autoc_reg & IXGBE_AUTOC_KX_SUPP)
+ if (autoc & IXGBE_AUTOC_KX_SUPP)
*speed |= IXGBE_LINK_SPEED_1GB_FULL;
*autoneg = true;
break;
}
/**
- * ixgbe_get_copper_link_settings_82598 - Determines default link settings
+ * ixgbe_get_copper_link_capabilities_82598 - Determines link capabilities
* @hw: pointer to hardware structure
* @speed: pointer to link speed
* @autoneg: boolean auto-negotiation value
*
- * Determines the default link settings by reading the AUTOC register.
+ * Determines the link capabilities by reading the AUTOC register.
**/
-static s32 ixgbe_get_copper_link_settings_82598(struct ixgbe_hw *hw,
- u32 *speed, bool *autoneg)
+static s32 ixgbe_get_copper_link_capabilities_82598(struct ixgbe_hw *hw,
+ ixgbe_link_speed *speed,
+ bool *autoneg)
{
s32 status = IXGBE_ERR_LINK_SETUP;
u16 speed_ability;
*speed = 0;
*autoneg = true;
- status = ixgbe_read_phy_reg(hw, IXGBE_MDIO_PHY_SPEED_ABILITY,
- IXGBE_MDIO_PMA_PMD_DEV_TYPE,
- &speed_ability);
+ status = hw->phy.ops.read_reg(hw, MDIO_SPEED, MDIO_MMD_PMAPMD,
+ &speed_ability);
if (status == 0) {
- if (speed_ability & IXGBE_MDIO_PHY_SPEED_10G)
+ if (speed_ability & MDIO_SPEED_10G)
*speed |= IXGBE_LINK_SPEED_10GB_FULL;
- if (speed_ability & IXGBE_MDIO_PHY_SPEED_1G)
+ if (speed_ability & MDIO_PMA_SPEED_1000)
*speed |= IXGBE_LINK_SPEED_1GB_FULL;
}
/* Media type for I82598 is based on device ID */
switch (hw->device_id) {
+ case IXGBE_DEV_ID_82598:
+ case IXGBE_DEV_ID_82598_BX:
+ media_type = ixgbe_media_type_backplane;
+ break;
case IXGBE_DEV_ID_82598AF_DUAL_PORT:
case IXGBE_DEV_ID_82598AF_SINGLE_PORT:
- case IXGBE_DEV_ID_82598EB_CX4:
- case IXGBE_DEV_ID_82598_CX4_DUAL_PORT:
+ case IXGBE_DEV_ID_82598_DA_DUAL_PORT:
+ case IXGBE_DEV_ID_82598_SR_DUAL_PORT_EM:
case IXGBE_DEV_ID_82598EB_XF_LR:
+ case IXGBE_DEV_ID_82598EB_SFP_LOM:
media_type = ixgbe_media_type_fiber;
break;
- case IXGBE_DEV_ID_82598AT_DUAL_PORT:
+ case IXGBE_DEV_ID_82598EB_CX4:
+ case IXGBE_DEV_ID_82598_CX4_DUAL_PORT:
+ media_type = ixgbe_media_type_cx4;
+ break;
+ case IXGBE_DEV_ID_82598AT:
+ case IXGBE_DEV_ID_82598AT2:
media_type = ixgbe_media_type_copper;
break;
default:
}
/**
- * ixgbe_setup_mac_link_82598 - Configures MAC link settings
+ * ixgbe_fc_enable_82598 - Enable flow control
+ * @hw: pointer to hardware structure
+ * @packetbuf_num: packet buffer number (0-7)
+ *
+ * Enable flow control according to the current settings.
+ **/
+static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
+{
+ s32 ret_val = 0;
+ u32 fctrl_reg;
+ u32 rmcs_reg;
+ u32 reg;
+ u32 link_speed = 0;
+ bool link_up;
+
+#ifdef CONFIG_DCB
+ if (hw->fc.requested_mode == ixgbe_fc_pfc)
+ goto out;
+
+#endif /* CONFIG_DCB */
+ /*
+ * On 82598 having Rx FC on causes resets while doing 1G
+ * so if it's on turn it off once we know link_speed. For
+ * more details see 82598 Specification update.
+ */
+ hw->mac.ops.check_link(hw, &link_speed, &link_up, false);
+ if (link_up && link_speed == IXGBE_LINK_SPEED_1GB_FULL) {
+ switch (hw->fc.requested_mode) {
+ case ixgbe_fc_full:
+ hw->fc.requested_mode = ixgbe_fc_tx_pause;
+ break;
+ case ixgbe_fc_rx_pause:
+ hw->fc.requested_mode = ixgbe_fc_none;
+ break;
+ default:
+ /* no change */
+ break;
+ }
+ }
+
+ /* Negotiate the fc mode to use */
+ ret_val = ixgbe_fc_autoneg(hw);
+ if (ret_val)
+ goto out;
+
+ /* Disable any previous flow control settings */
+ fctrl_reg = IXGBE_READ_REG(hw, IXGBE_FCTRL);
+ fctrl_reg &= ~(IXGBE_FCTRL_RFCE | IXGBE_FCTRL_RPFCE);
+
+ rmcs_reg = IXGBE_READ_REG(hw, IXGBE_RMCS);
+ rmcs_reg &= ~(IXGBE_RMCS_TFCE_PRIORITY | IXGBE_RMCS_TFCE_802_3X);
+
+ /*
+ * The possible values of fc.current_mode are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause frames,
+ * but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames but
+ * we do not support receiving pause frames).
+ * 3: Both Rx and Tx flow control (symmetric) are enabled.
+ * other: Invalid.
+#ifdef CONFIG_DCB
+ * 4: Priority Flow Control is enabled.
+#endif
+ */
+ switch (hw->fc.current_mode) {
+ case ixgbe_fc_none:
+ /*
+ * Flow control is disabled by software override or autoneg.
+ * The code below will actually disable it in the HW.
+ */
+ break;
+ case ixgbe_fc_rx_pause:
+ /*
+ * Rx Flow control is enabled and Tx Flow control is
+ * disabled by software override. Since there really
+ * isn't a way to advertise that we are capable of RX
+ * Pause ONLY, we will advertise that we support both
+ * symmetric and asymmetric Rx PAUSE. Later, we will
+ * disable the adapter's ability to send PAUSE frames.
+ */
+ fctrl_reg |= IXGBE_FCTRL_RFCE;
+ break;
+ case ixgbe_fc_tx_pause:
+ /*
+ * Tx Flow control is enabled, and Rx Flow control is
+ * disabled by software override.
+ */
+ rmcs_reg |= IXGBE_RMCS_TFCE_802_3X;
+ break;
+ case ixgbe_fc_full:
+ /* Flow control (both Rx and Tx) is enabled by SW override. */
+ fctrl_reg |= IXGBE_FCTRL_RFCE;
+ rmcs_reg |= IXGBE_RMCS_TFCE_802_3X;
+ break;
+#ifdef CONFIG_DCB
+ case ixgbe_fc_pfc:
+ goto out;
+ break;
+#endif /* CONFIG_DCB */
+ default:
+ hw_dbg(hw, "Flow control param set incorrectly\n");
+ ret_val = IXGBE_ERR_CONFIG;
+ goto out;
+ break;
+ }
+
+ /* Set 802.3x based flow control settings. */
+ fctrl_reg |= IXGBE_FCTRL_DPF;
+ IXGBE_WRITE_REG(hw, IXGBE_FCTRL, fctrl_reg);
+ IXGBE_WRITE_REG(hw, IXGBE_RMCS, rmcs_reg);
+
+ /* Set up and enable Rx high/low water mark thresholds, enable XON. */
+ if (hw->fc.current_mode & ixgbe_fc_tx_pause) {
+ if (hw->fc.send_xon) {
+ IXGBE_WRITE_REG(hw, IXGBE_FCRTL(packetbuf_num),
+ (hw->fc.low_water | IXGBE_FCRTL_XONE));
+ } else {
+ IXGBE_WRITE_REG(hw, IXGBE_FCRTL(packetbuf_num),
+ hw->fc.low_water);
+ }
+
+ IXGBE_WRITE_REG(hw, IXGBE_FCRTH(packetbuf_num),
+ (hw->fc.high_water | IXGBE_FCRTH_FCEN));
+ }
+
+ /* Configure pause time (2 TCs per register) */
+ reg = IXGBE_READ_REG(hw, IXGBE_FCTTV(packetbuf_num / 2));
+ if ((packetbuf_num & 1) == 0)
+ reg = (reg & 0xFFFF0000) | hw->fc.pause_time;
+ else
+ reg = (reg & 0x0000FFFF) | (hw->fc.pause_time << 16);
+ IXGBE_WRITE_REG(hw, IXGBE_FCTTV(packetbuf_num / 2), reg);
+
+ IXGBE_WRITE_REG(hw, IXGBE_FCRTV, (hw->fc.pause_time >> 1));
+
+out:
+ return ret_val;
+}
+
+/**
+ * ixgbe_start_mac_link_82598 - Configures MAC link settings
* @hw: pointer to hardware structure
*
* Configures link settings based on values in the ixgbe_hw struct.
* Restarts the link. Performs autonegotiation if needed.
**/
-static s32 ixgbe_setup_mac_link_82598(struct ixgbe_hw *hw)
+static s32 ixgbe_start_mac_link_82598(struct ixgbe_hw *hw,
+ bool autoneg_wait_to_complete)
{
u32 autoc_reg;
u32 links_reg;
u32 i;
s32 status = 0;
- autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
-
- if (hw->mac.link_settings_loaded) {
- autoc_reg &= ~IXGBE_AUTOC_LMS_ATTACH_TYPE;
- autoc_reg &= ~IXGBE_AUTOC_LMS_MASK;
- autoc_reg |= hw->mac.link_attach_type;
- autoc_reg |= hw->mac.link_mode_select;
-
- IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg);
- IXGBE_WRITE_FLUSH(hw);
- msleep(50);
- }
-
/* Restart link */
+ autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
autoc_reg |= IXGBE_AUTOC_AN_RESTART;
IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg);
/* Only poll for autoneg to complete if specified to do so */
- if (hw->phy.autoneg_wait_to_complete) {
- if (hw->mac.link_mode_select == IXGBE_AUTOC_LMS_KX4_AN ||
- hw->mac.link_mode_select == IXGBE_AUTOC_LMS_KX4_AN_1G_AN) {
+ if (autoneg_wait_to_complete) {
+ if ((autoc_reg & IXGBE_AUTOC_LMS_MASK) ==
+ IXGBE_AUTOC_LMS_KX4_AN ||
+ (autoc_reg & IXGBE_AUTOC_LMS_MASK) ==
+ IXGBE_AUTOC_LMS_KX4_AN_1G_AN) {
links_reg = 0; /* Just in case Autoneg time = 0 */
for (i = 0; i < IXGBE_AUTO_NEG_TIME; i++) {
links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS);
}
if (!(links_reg & IXGBE_LINKS_KX_AN_COMP)) {
status = IXGBE_ERR_AUTONEG_NOT_COMPLETE;
- hw_dbg(hw,
- "Autonegotiation did not complete.\n");
+ hw_dbg(hw, "Autonegotiation did not complete.\n");
}
}
}
- /*
- * We want to save off the original Flow Control configuration just in
- * case we get disconnected and then reconnected into a different hub
- * or switch with different Flow Control capabilities.
- */
- hw->fc.type = hw->fc.original_type;
- ixgbe_setup_fc(hw, 0);
-
/* Add delay to filter out noises during initial link setup */
msleep(50);
}
/**
+ * ixgbe_validate_link_ready - Function looks for phy link
+ * @hw: pointer to hardware structure
+ *
+ * Function indicates success when phy link is available. If phy is not ready
+ * within 5 seconds of MAC indicating link, the function returns error.
+ **/
+static s32 ixgbe_validate_link_ready(struct ixgbe_hw *hw)
+{
+ u32 timeout;
+ u16 an_reg;
+
+ if (hw->device_id != IXGBE_DEV_ID_82598AT2)
+ return 0;
+
+ for (timeout = 0;
+ timeout < IXGBE_VALIDATE_LINK_READY_TIMEOUT; timeout++) {
+ hw->phy.ops.read_reg(hw, MDIO_STAT1, MDIO_MMD_AN, &an_reg);
+
+ if ((an_reg & MDIO_AN_STAT1_COMPLETE) &&
+ (an_reg & MDIO_STAT1_LSTATUS))
+ break;
+
+ msleep(100);
+ }
+
+ if (timeout == IXGBE_VALIDATE_LINK_READY_TIMEOUT) {
+ hw_dbg(hw, "Link was indicated but link is down\n");
+ return IXGBE_ERR_LINK_SETUP;
+ }
+
+ return 0;
+}
+
+/**
* ixgbe_check_mac_link_82598 - Get link/speed status
* @hw: pointer to hardware structure
* @speed: pointer to link speed
*
* Reads the links register to determine if link is up and the current speed
**/
-static s32 ixgbe_check_mac_link_82598(struct ixgbe_hw *hw, u32 *speed,
- bool *link_up,
+static s32 ixgbe_check_mac_link_82598(struct ixgbe_hw *hw,
+ ixgbe_link_speed *speed, bool *link_up,
bool link_up_wait_to_complete)
{
u32 links_reg;
u32 i;
+ u16 link_reg, adapt_comp_reg;
- links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS);
+ /*
+ * SERDES PHY requires us to read link status from register 0xC79F.
+ * Bit 0 set indicates link is up/ready; clear indicates link down.
+ * 0xC00C is read to check that the XAUI lanes are active. Bit 0
+ * clear indicates active; set indicates inactive.
+ */
+ if (hw->phy.type == ixgbe_phy_nl) {
+ hw->phy.ops.read_reg(hw, 0xC79F, MDIO_MMD_PMAPMD, &link_reg);
+ hw->phy.ops.read_reg(hw, 0xC79F, MDIO_MMD_PMAPMD, &link_reg);
+ hw->phy.ops.read_reg(hw, 0xC00C, MDIO_MMD_PMAPMD,
+ &adapt_comp_reg);
+ if (link_up_wait_to_complete) {
+ for (i = 0; i < IXGBE_LINK_UP_TIME; i++) {
+ if ((link_reg & 1) &&
+ ((adapt_comp_reg & 1) == 0)) {
+ *link_up = true;
+ break;
+ } else {
+ *link_up = false;
+ }
+ msleep(100);
+ hw->phy.ops.read_reg(hw, 0xC79F,
+ MDIO_MMD_PMAPMD,
+ &link_reg);
+ hw->phy.ops.read_reg(hw, 0xC00C,
+ MDIO_MMD_PMAPMD,
+ &adapt_comp_reg);
+ }
+ } else {
+ if ((link_reg & 1) && ((adapt_comp_reg & 1) == 0))
+ *link_up = true;
+ else
+ *link_up = false;
+ }
+ if (*link_up == false)
+ goto out;
+ }
+
+ links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS);
if (link_up_wait_to_complete) {
for (i = 0; i < IXGBE_LINK_UP_TIME; i++) {
if (links_reg & IXGBE_LINKS_UP) {
else
*speed = IXGBE_LINK_SPEED_1GB_FULL;
+ if ((hw->device_id == IXGBE_DEV_ID_82598AT2) && (*link_up == true) &&
+ (ixgbe_validate_link_ready(hw) != 0))
+ *link_up = false;
+
+ /* if link is down, zero out the current_mode */
+ if (*link_up == false) {
+ hw->fc.current_mode = ixgbe_fc_none;
+ hw->fc.fc_was_autonegged = false;
+ }
+out:
return 0;
}
+
/**
- * ixgbe_setup_mac_link_speed_82598 - Set MAC link speed
+ * ixgbe_setup_mac_link_82598 - Set MAC link speed
* @hw: pointer to hardware structure
* @speed: new link speed
* @autoneg: true if auto-negotiation enabled
*
* Set the link speed in the AUTOC register and restarts link.
**/
-static s32 ixgbe_setup_mac_link_speed_82598(struct ixgbe_hw *hw,
- u32 speed, bool autoneg,
- bool autoneg_wait_to_complete)
+static s32 ixgbe_setup_mac_link_82598(struct ixgbe_hw *hw,
+ ixgbe_link_speed speed, bool autoneg,
+ bool autoneg_wait_to_complete)
{
- s32 status = 0;
+ s32 status = 0;
+ ixgbe_link_speed link_capabilities = IXGBE_LINK_SPEED_UNKNOWN;
+ u32 curr_autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC);
+ u32 autoc = curr_autoc;
+ u32 link_mode = autoc & IXGBE_AUTOC_LMS_MASK;
- /* If speed is 10G, then check for CX4 or XAUI. */
- if ((speed == IXGBE_LINK_SPEED_10GB_FULL) &&
- (!(hw->mac.link_attach_type & IXGBE_AUTOC_10G_KX4)))
- hw->mac.link_mode_select = IXGBE_AUTOC_LMS_10G_LINK_NO_AN;
- else if ((speed == IXGBE_LINK_SPEED_1GB_FULL) && (!autoneg))
- hw->mac.link_mode_select = IXGBE_AUTOC_LMS_1G_LINK_NO_AN;
- else if (autoneg) {
- /* BX mode - Autonegotiate 1G */
- if (!(hw->mac.link_attach_type & IXGBE_AUTOC_1G_PMA_PMD))
- hw->mac.link_mode_select = IXGBE_AUTOC_LMS_1G_AN;
- else /* KX/KX4 mode */
- hw->mac.link_mode_select = IXGBE_AUTOC_LMS_KX4_AN_1G_AN;
- } else {
+ /* Check to see if speed passed in is supported. */
+ ixgbe_get_link_capabilities_82598(hw, &link_capabilities, &autoneg);
+ speed &= link_capabilities;
+
+ if (speed == IXGBE_LINK_SPEED_UNKNOWN)
status = IXGBE_ERR_LINK_SETUP;
+
+ /* Set KX4/KX support according to speed requested */
+ else if (link_mode == IXGBE_AUTOC_LMS_KX4_AN ||
+ link_mode == IXGBE_AUTOC_LMS_KX4_AN_1G_AN) {
+ autoc &= ~IXGBE_AUTOC_KX4_KX_SUPP_MASK;
+ if (speed & IXGBE_LINK_SPEED_10GB_FULL)
+ autoc |= IXGBE_AUTOC_KX4_SUPP;
+ if (speed & IXGBE_LINK_SPEED_1GB_FULL)
+ autoc |= IXGBE_AUTOC_KX_SUPP;
+ if (autoc != curr_autoc)
+ IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc);
}
if (status == 0) {
- hw->phy.autoneg_wait_to_complete = autoneg_wait_to_complete;
-
- hw->mac.link_settings_loaded = true;
/*
* Setup and restart the link based on the new values in
* ixgbe_hw This will write the AUTOC register based on the new
* stored values
*/
- hw->mac.ops.setup_link(hw);
+ status = ixgbe_start_mac_link_82598(hw, autoneg_wait_to_complete);
}
return status;
/**
- * ixgbe_setup_copper_link_82598 - Setup copper link settings
- * @hw: pointer to hardware structure
- *
- * Configures link settings based on values in the ixgbe_hw struct.
- * Restarts the link. Performs autonegotiation if needed. Restart
- * phy and wait for autonegotiate to finish. Then synchronize the
- * MAC and PHY.
- **/
-static s32 ixgbe_setup_copper_link_82598(struct ixgbe_hw *hw)
-{
- s32 status = 0;
-
- /* Restart autonegotiation on PHY */
- if (hw->phy.ops.setup_link)
- status = hw->phy.ops.setup_link(hw);
-
- /* Set MAC to KX/KX4 autoneg, which defaultis to Parallel detection */
- hw->mac.link_attach_type = (IXGBE_AUTOC_10G_KX4 | IXGBE_AUTOC_1G_KX);
- hw->mac.link_mode_select = IXGBE_AUTOC_LMS_KX4_AN;
-
- /* Set up MAC */
- hw->mac.ops.setup_link(hw);
-
- return status;
-}
-
-/**
- * ixgbe_setup_copper_link_speed_82598 - Set the PHY autoneg advertised field
+ * ixgbe_setup_copper_link_82598 - Set the PHY autoneg advertised field
* @hw: pointer to hardware structure
* @speed: new link speed
* @autoneg: true if autonegotiation enabled
*
* Sets the link speed in the AUTOC register in the MAC and restarts link.
**/
-static s32 ixgbe_setup_copper_link_speed_82598(struct ixgbe_hw *hw, u32 speed,
- bool autoneg,
- bool autoneg_wait_to_complete)
+static s32 ixgbe_setup_copper_link_82598(struct ixgbe_hw *hw,
+ ixgbe_link_speed speed,
+ bool autoneg,
+ bool autoneg_wait_to_complete)
{
- s32 status = 0;
+ s32 status;
/* Setup the PHY according to input speed */
- if (hw->phy.ops.setup_link_speed)
- status = hw->phy.ops.setup_link_speed(hw, speed, autoneg,
- autoneg_wait_to_complete);
-
- /* Set MAC to KX/KX4 autoneg, which defaults to Parallel detection */
- hw->mac.link_attach_type = (IXGBE_AUTOC_10G_KX4 | IXGBE_AUTOC_1G_KX);
- hw->mac.link_mode_select = IXGBE_AUTOC_LMS_KX4_AN;
+ status = hw->phy.ops.setup_link_speed(hw, speed, autoneg,
+ autoneg_wait_to_complete);
/* Set up MAC */
- hw->mac.ops.setup_link(hw);
+ ixgbe_start_mac_link_82598(hw, autoneg_wait_to_complete);
return status;
}
* ixgbe_reset_hw_82598 - Performs hardware reset
* @hw: pointer to hardware structure
*
- * Resets the hardware by reseting the transmit and receive units, masks and
+ * Resets the hardware by resetting the transmit and receive units, masks and
* clears all interrupts, performing a PHY reset, and performing a link (MAC)
* reset.
**/
static s32 ixgbe_reset_hw_82598(struct ixgbe_hw *hw)
{
s32 status = 0;
+ s32 phy_status = 0;
u32 ctrl;
u32 gheccr;
u32 i;
u8 analog_val;
/* Call adapter stop to disable tx/rx and clear interrupts */
- ixgbe_stop_adapter(hw);
+ hw->mac.ops.stop_adapter(hw);
/*
- * Power up the Atlas TX lanes if they are currently powered down.
- * Atlas TX lanes are powered down for MAC loopback tests, but
+ * Power up the Atlas Tx lanes if they are currently powered down.
+ * Atlas Tx lanes are powered down for MAC loopback tests, but
* they are not automatically restored on reset.
*/
- ixgbe_read_analog_reg8(hw, IXGBE_ATLAS_PDN_LPBK, &analog_val);
+ hw->mac.ops.read_analog_reg8(hw, IXGBE_ATLAS_PDN_LPBK, &analog_val);
if (analog_val & IXGBE_ATLAS_PDN_TX_REG_EN) {
- /* Enable TX Atlas so packets can be transmitted again */
- ixgbe_read_analog_reg8(hw, IXGBE_ATLAS_PDN_LPBK, &analog_val);
+ /* Enable Tx Atlas so packets can be transmitted again */
+ hw->mac.ops.read_analog_reg8(hw, IXGBE_ATLAS_PDN_LPBK,
+ &analog_val);
analog_val &= ~IXGBE_ATLAS_PDN_TX_REG_EN;
- ixgbe_write_analog_reg8(hw, IXGBE_ATLAS_PDN_LPBK, analog_val);
+ hw->mac.ops.write_analog_reg8(hw, IXGBE_ATLAS_PDN_LPBK,
+ analog_val);
- ixgbe_read_analog_reg8(hw, IXGBE_ATLAS_PDN_10G, &analog_val);
+ hw->mac.ops.read_analog_reg8(hw, IXGBE_ATLAS_PDN_10G,
+ &analog_val);
analog_val &= ~IXGBE_ATLAS_PDN_TX_10G_QL_ALL;
- ixgbe_write_analog_reg8(hw, IXGBE_ATLAS_PDN_10G, analog_val);
+ hw->mac.ops.write_analog_reg8(hw, IXGBE_ATLAS_PDN_10G,
+ analog_val);
- ixgbe_read_analog_reg8(hw, IXGBE_ATLAS_PDN_1G, &analog_val);
+ hw->mac.ops.read_analog_reg8(hw, IXGBE_ATLAS_PDN_1G,
+ &analog_val);
analog_val &= ~IXGBE_ATLAS_PDN_TX_1G_QL_ALL;
- ixgbe_write_analog_reg8(hw, IXGBE_ATLAS_PDN_1G, analog_val);
+ hw->mac.ops.write_analog_reg8(hw, IXGBE_ATLAS_PDN_1G,
+ analog_val);
- ixgbe_read_analog_reg8(hw, IXGBE_ATLAS_PDN_AN, &analog_val);
+ hw->mac.ops.read_analog_reg8(hw, IXGBE_ATLAS_PDN_AN,
+ &analog_val);
analog_val &= ~IXGBE_ATLAS_PDN_TX_AN_QL_ALL;
- ixgbe_write_analog_reg8(hw, IXGBE_ATLAS_PDN_AN, analog_val);
+ hw->mac.ops.write_analog_reg8(hw, IXGBE_ATLAS_PDN_AN,
+ analog_val);
}
/* Reset PHY */
- ixgbe_reset_phy(hw);
+ if (hw->phy.reset_disable == false) {
+ /* PHY ops must be identified and initialized prior to reset */
+
+ /* Init PHY and function pointers, perform SFP setup */
+ phy_status = hw->phy.ops.init(hw);
+ if (phy_status == IXGBE_ERR_SFP_NOT_SUPPORTED)
+ goto reset_hw_out;
+ else if (phy_status == IXGBE_ERR_SFP_NOT_PRESENT)
+ goto no_phy_reset;
+
+ hw->phy.ops.reset(hw);
+ }
+
+no_phy_reset:
/*
* Prevent the PCI-E bus from from hanging by disabling PCI-E master
* access and verify no pending requests before reset
*/
- if (ixgbe_disable_pcie_master(hw) != 0) {
+ status = ixgbe_disable_pcie_master(hw);
+ if (status != 0) {
status = IXGBE_ERR_MASTER_REQUESTS_PENDING;
hw_dbg(hw, "PCI-E Master disable polling has failed.\n");
}
IXGBE_WRITE_REG(hw, IXGBE_GHECCR, gheccr);
/*
- * AUTOC register which stores link settings gets cleared
- * and reloaded from EEPROM after reset. We need to restore
- * our stored value from init in case SW changed the attach
- * type or speed. If this is the first time and link settings
- * have not been stored, store default settings from AUTOC.
+ * Store the original AUTOC value if it has not been
+ * stored off yet. Otherwise restore the stored original
+ * AUTOC value since the reset operation sets back to deaults.
*/
autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC);
- if (hw->mac.link_settings_loaded) {
- autoc &= ~(IXGBE_AUTOC_LMS_ATTACH_TYPE);
- autoc &= ~(IXGBE_AUTOC_LMS_MASK);
- autoc |= hw->mac.link_attach_type;
- autoc |= hw->mac.link_mode_select;
- IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc);
- } else {
- hw->mac.link_attach_type =
- (autoc & IXGBE_AUTOC_LMS_ATTACH_TYPE);
- hw->mac.link_mode_select = (autoc & IXGBE_AUTOC_LMS_MASK);
- hw->mac.link_settings_loaded = true;
+ if (hw->mac.orig_link_settings_stored == false) {
+ hw->mac.orig_autoc = autoc;
+ hw->mac.orig_link_settings_stored = true;
+ } else if (autoc != hw->mac.orig_autoc) {
+ IXGBE_WRITE_REG(hw, IXGBE_AUTOC, hw->mac.orig_autoc);
}
+ /*
+ * Store MAC address from RAR0, clear receive address registers, and
+ * clear the multicast table
+ */
+ hw->mac.ops.init_rx_addrs(hw);
+
/* Store the permanent mac address */
- ixgbe_get_mac_addr(hw, hw->mac.perm_addr);
+ hw->mac.ops.get_mac_addr(hw, hw->mac.perm_addr);
+
+reset_hw_out:
+ if (phy_status)
+ status = phy_status;
+
+ return status;
+}
+
+/**
+ * ixgbe_set_vmdq_82598 - Associate a VMDq set index with a rx address
+ * @hw: pointer to hardware struct
+ * @rar: receive address register index to associate with a VMDq index
+ * @vmdq: VMDq set index
+ **/
+static s32 ixgbe_set_vmdq_82598(struct ixgbe_hw *hw, u32 rar, u32 vmdq)
+{
+ u32 rar_high;
+
+ rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(rar));
+ rar_high &= ~IXGBE_RAH_VIND_MASK;
+ rar_high |= ((vmdq << IXGBE_RAH_VIND_SHIFT) & IXGBE_RAH_VIND_MASK);
+ IXGBE_WRITE_REG(hw, IXGBE_RAH(rar), rar_high);
+ return 0;
+}
+
+/**
+ * ixgbe_clear_vmdq_82598 - Disassociate a VMDq set index from an rx address
+ * @hw: pointer to hardware struct
+ * @rar: receive address register index to associate with a VMDq index
+ * @vmdq: VMDq clear index (not used in 82598, but elsewhere)
+ **/
+static s32 ixgbe_clear_vmdq_82598(struct ixgbe_hw *hw, u32 rar, u32 vmdq)
+{
+ u32 rar_high;
+ u32 rar_entries = hw->mac.num_rar_entries;
+
+ if (rar < rar_entries) {
+ rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(rar));
+ if (rar_high & IXGBE_RAH_VIND_MASK) {
+ rar_high &= ~IXGBE_RAH_VIND_MASK;
+ IXGBE_WRITE_REG(hw, IXGBE_RAH(rar), rar_high);
+ }
+ } else {
+ hw_dbg(hw, "RAR index %d is out of range.\n", rar);
+ }
+
+ return 0;
+}
+
+/**
+ * ixgbe_set_vfta_82598 - Set VLAN filter table
+ * @hw: pointer to hardware structure
+ * @vlan: VLAN id to write to VLAN filter
+ * @vind: VMDq output index that maps queue to VLAN id in VFTA
+ * @vlan_on: boolean flag to turn on/off VLAN in VFTA
+ *
+ * Turn on/off specified VLAN in the VLAN filter table.
+ **/
+static s32 ixgbe_set_vfta_82598(struct ixgbe_hw *hw, u32 vlan, u32 vind,
+ bool vlan_on)
+{
+ u32 regindex;
+ u32 bitindex;
+ u32 bits;
+ u32 vftabyte;
+
+ if (vlan > 4095)
+ return IXGBE_ERR_PARAM;
+
+ /* Determine 32-bit word position in array */
+ regindex = (vlan >> 5) & 0x7F; /* upper seven bits */
+
+ /* Determine the location of the (VMD) queue index */
+ vftabyte = ((vlan >> 3) & 0x03); /* bits (4:3) indicating byte array */
+ bitindex = (vlan & 0x7) << 2; /* lower 3 bits indicate nibble */
+
+ /* Set the nibble for VMD queue index */
+ bits = IXGBE_READ_REG(hw, IXGBE_VFTAVIND(vftabyte, regindex));
+ bits &= (~(0x0F << bitindex));
+ bits |= (vind << bitindex);
+ IXGBE_WRITE_REG(hw, IXGBE_VFTAVIND(vftabyte, regindex), bits);
+
+ /* Determine the location of the bit for this VLAN id */
+ bitindex = vlan & 0x1F; /* lower five bits */
+
+ bits = IXGBE_READ_REG(hw, IXGBE_VFTA(regindex));
+ if (vlan_on)
+ /* Turn on this VLAN id */
+ bits |= (1 << bitindex);
+ else
+ /* Turn off this VLAN id */
+ bits &= ~(1 << bitindex);
+ IXGBE_WRITE_REG(hw, IXGBE_VFTA(regindex), bits);
+
+ return 0;
+}
+
+/**
+ * ixgbe_clear_vfta_82598 - Clear VLAN filter table
+ * @hw: pointer to hardware structure
+ *
+ * Clears the VLAN filer table, and the VMDq index associated with the filter
+ **/
+static s32 ixgbe_clear_vfta_82598(struct ixgbe_hw *hw)
+{
+ u32 offset;
+ u32 vlanbyte;
+
+ for (offset = 0; offset < hw->mac.vft_size; offset++)
+ IXGBE_WRITE_REG(hw, IXGBE_VFTA(offset), 0);
+
+ for (vlanbyte = 0; vlanbyte < 4; vlanbyte++)
+ for (offset = 0; offset < hw->mac.vft_size; offset++)
+ IXGBE_WRITE_REG(hw, IXGBE_VFTAVIND(vlanbyte, offset),
+ 0);
+
+ return 0;
+}
+
+/**
+ * ixgbe_read_analog_reg8_82598 - Reads 8 bit Atlas analog register
+ * @hw: pointer to hardware structure
+ * @reg: analog register to read
+ * @val: read value
+ *
+ * Performs read operation to Atlas analog register specified.
+ **/
+static s32 ixgbe_read_analog_reg8_82598(struct ixgbe_hw *hw, u32 reg, u8 *val)
+{
+ u32 atlas_ctl;
+
+ IXGBE_WRITE_REG(hw, IXGBE_ATLASCTL,
+ IXGBE_ATLASCTL_WRITE_CMD | (reg << 8));
+ IXGBE_WRITE_FLUSH(hw);
+ udelay(10);
+ atlas_ctl = IXGBE_READ_REG(hw, IXGBE_ATLASCTL);
+ *val = (u8)atlas_ctl;
+
+ return 0;
+}
+
+/**
+ * ixgbe_write_analog_reg8_82598 - Writes 8 bit Atlas analog register
+ * @hw: pointer to hardware structure
+ * @reg: atlas register to write
+ * @val: value to write
+ *
+ * Performs write operation to Atlas analog register specified.
+ **/
+static s32 ixgbe_write_analog_reg8_82598(struct ixgbe_hw *hw, u32 reg, u8 val)
+{
+ u32 atlas_ctl;
+
+ atlas_ctl = (reg << 8) | val;
+ IXGBE_WRITE_REG(hw, IXGBE_ATLASCTL, atlas_ctl);
+ IXGBE_WRITE_FLUSH(hw);
+ udelay(10);
+ return 0;
+}
+
+/**
+ * ixgbe_read_i2c_eeprom_82598 - Read 8 bit EEPROM word of an SFP+ module
+ * over I2C interface through an intermediate phy.
+ * @hw: pointer to hardware structure
+ * @byte_offset: EEPROM byte offset to read
+ * @eeprom_data: value read
+ *
+ * Performs byte read operation to SFP module's EEPROM over I2C interface.
+ **/
+static s32 ixgbe_read_i2c_eeprom_82598(struct ixgbe_hw *hw, u8 byte_offset,
+ u8 *eeprom_data)
+{
+ s32 status = 0;
+ u16 sfp_addr = 0;
+ u16 sfp_data = 0;
+ u16 sfp_stat = 0;
+ u32 i;
+
+ if (hw->phy.type == ixgbe_phy_nl) {
+ /*
+ * phy SDA/SCL registers are at addresses 0xC30A to
+ * 0xC30D. These registers are used to talk to the SFP+
+ * module's EEPROM through the SDA/SCL (I2C) interface.
+ */
+ sfp_addr = (IXGBE_I2C_EEPROM_DEV_ADDR << 8) + byte_offset;
+ sfp_addr = (sfp_addr | IXGBE_I2C_EEPROM_READ_MASK);
+ hw->phy.ops.write_reg(hw,
+ IXGBE_MDIO_PMA_PMD_SDA_SCL_ADDR,
+ MDIO_MMD_PMAPMD,
+ sfp_addr);
+
+ /* Poll status */
+ for (i = 0; i < 100; i++) {
+ hw->phy.ops.read_reg(hw,
+ IXGBE_MDIO_PMA_PMD_SDA_SCL_STAT,
+ MDIO_MMD_PMAPMD,
+ &sfp_stat);
+ sfp_stat = sfp_stat & IXGBE_I2C_EEPROM_STATUS_MASK;
+ if (sfp_stat != IXGBE_I2C_EEPROM_STATUS_IN_PROGRESS)
+ break;
+ msleep(10);
+ }
+
+ if (sfp_stat != IXGBE_I2C_EEPROM_STATUS_PASS) {
+ hw_dbg(hw, "EEPROM read did not pass.\n");
+ status = IXGBE_ERR_SFP_NOT_PRESENT;
+ goto out;
+ }
+
+ /* Read data */
+ hw->phy.ops.read_reg(hw, IXGBE_MDIO_PMA_PMD_SDA_SCL_DATA,
+ MDIO_MMD_PMAPMD, &sfp_data);
+
+ *eeprom_data = (u8)(sfp_data >> 8);
+ } else {
+ status = IXGBE_ERR_PHY;
+ goto out;
+ }
+
+out:
return status;
}
+/**
+ * ixgbe_get_supported_physical_layer_82598 - Returns physical layer type
+ * @hw: pointer to hardware structure
+ *
+ * Determines physical layer capabilities of the current configuration.
+ **/
+static u32 ixgbe_get_supported_physical_layer_82598(struct ixgbe_hw *hw)
+{
+ u32 physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN;
+ u32 autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC);
+ u32 pma_pmd_10g = autoc & IXGBE_AUTOC_10G_PMA_PMD_MASK;
+ u32 pma_pmd_1g = autoc & IXGBE_AUTOC_1G_PMA_PMD_MASK;
+ u16 ext_ability = 0;
+
+ hw->phy.ops.identify(hw);
+
+ /* Copper PHY must be checked before AUTOC LMS to determine correct
+ * physical layer because 10GBase-T PHYs use LMS = KX4/KX */
+ if (hw->phy.type == ixgbe_phy_tn ||
+ hw->phy.type == ixgbe_phy_cu_unknown) {
+ hw->phy.ops.read_reg(hw, MDIO_PMA_EXTABLE, MDIO_MMD_PMAPMD,
+ &ext_ability);
+ if (ext_ability & MDIO_PMA_EXTABLE_10GBT)
+ physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_T;
+ if (ext_ability & MDIO_PMA_EXTABLE_1000BT)
+ physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_T;
+ if (ext_ability & MDIO_PMA_EXTABLE_100BTX)
+ physical_layer |= IXGBE_PHYSICAL_LAYER_100BASE_TX;
+ goto out;
+ }
+
+ switch (autoc & IXGBE_AUTOC_LMS_MASK) {
+ case IXGBE_AUTOC_LMS_1G_AN:
+ case IXGBE_AUTOC_LMS_1G_LINK_NO_AN:
+ if (pma_pmd_1g == IXGBE_AUTOC_1G_KX)
+ physical_layer = IXGBE_PHYSICAL_LAYER_1000BASE_KX;
+ else
+ physical_layer = IXGBE_PHYSICAL_LAYER_1000BASE_BX;
+ break;
+ case IXGBE_AUTOC_LMS_10G_LINK_NO_AN:
+ if (pma_pmd_10g == IXGBE_AUTOC_10G_CX4)
+ physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_CX4;
+ else if (pma_pmd_10g == IXGBE_AUTOC_10G_KX4)
+ physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_KX4;
+ else /* XAUI */
+ physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN;
+ break;
+ case IXGBE_AUTOC_LMS_KX4_AN:
+ case IXGBE_AUTOC_LMS_KX4_AN_1G_AN:
+ if (autoc & IXGBE_AUTOC_KX_SUPP)
+ physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_KX;
+ if (autoc & IXGBE_AUTOC_KX4_SUPP)
+ physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_KX4;
+ break;
+ default:
+ break;
+ }
+
+ if (hw->phy.type == ixgbe_phy_nl) {
+ hw->phy.ops.identify_sfp(hw);
+
+ switch (hw->phy.sfp_type) {
+ case ixgbe_sfp_type_da_cu:
+ physical_layer = IXGBE_PHYSICAL_LAYER_SFP_PLUS_CU;
+ break;
+ case ixgbe_sfp_type_sr:
+ physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_SR;
+ break;
+ case ixgbe_sfp_type_lr:
+ physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_LR;
+ break;
+ default:
+ physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN;
+ break;
+ }
+ }
+
+ switch (hw->device_id) {
+ case IXGBE_DEV_ID_82598_DA_DUAL_PORT:
+ physical_layer = IXGBE_PHYSICAL_LAYER_SFP_PLUS_CU;
+ break;
+ case IXGBE_DEV_ID_82598AF_DUAL_PORT:
+ case IXGBE_DEV_ID_82598AF_SINGLE_PORT:
+ case IXGBE_DEV_ID_82598_SR_DUAL_PORT_EM:
+ physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_SR;
+ break;
+ case IXGBE_DEV_ID_82598EB_XF_LR:
+ physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_LR;
+ break;
+ default:
+ break;
+ }
+
+out:
+ return physical_layer;
+}
+
static struct ixgbe_mac_operations mac_ops_82598 = {
- .reset = &ixgbe_reset_hw_82598,
+ .init_hw = &ixgbe_init_hw_generic,
+ .reset_hw = &ixgbe_reset_hw_82598,
+ .start_hw = &ixgbe_start_hw_82598,
+ .clear_hw_cntrs = &ixgbe_clear_hw_cntrs_generic,
.get_media_type = &ixgbe_get_media_type_82598,
+ .get_supported_physical_layer = &ixgbe_get_supported_physical_layer_82598,
+ .enable_rx_dma = &ixgbe_enable_rx_dma_generic,
+ .get_mac_addr = &ixgbe_get_mac_addr_generic,
+ .stop_adapter = &ixgbe_stop_adapter_generic,
+ .get_bus_info = &ixgbe_get_bus_info_generic,
+ .set_lan_id = &ixgbe_set_lan_id_multi_port_pcie,
+ .read_analog_reg8 = &ixgbe_read_analog_reg8_82598,
+ .write_analog_reg8 = &ixgbe_write_analog_reg8_82598,
.setup_link = &ixgbe_setup_mac_link_82598,
.check_link = &ixgbe_check_mac_link_82598,
- .setup_link_speed = &ixgbe_setup_mac_link_speed_82598,
- .get_link_settings = &ixgbe_get_link_settings_82598,
+ .get_link_capabilities = &ixgbe_get_link_capabilities_82598,
+ .led_on = &ixgbe_led_on_generic,
+ .led_off = &ixgbe_led_off_generic,
+ .blink_led_start = &ixgbe_blink_led_start_generic,
+ .blink_led_stop = &ixgbe_blink_led_stop_generic,
+ .set_rar = &ixgbe_set_rar_generic,
+ .clear_rar = &ixgbe_clear_rar_generic,
+ .set_vmdq = &ixgbe_set_vmdq_82598,
+ .clear_vmdq = &ixgbe_clear_vmdq_82598,
+ .init_rx_addrs = &ixgbe_init_rx_addrs_generic,
+ .update_uc_addr_list = &ixgbe_update_uc_addr_list_generic,
+ .update_mc_addr_list = &ixgbe_update_mc_addr_list_generic,
+ .enable_mc = &ixgbe_enable_mc_generic,
+ .disable_mc = &ixgbe_disable_mc_generic,
+ .clear_vfta = &ixgbe_clear_vfta_82598,
+ .set_vfta = &ixgbe_set_vfta_82598,
+ .fc_enable = &ixgbe_fc_enable_82598,
+};
+
+static struct ixgbe_eeprom_operations eeprom_ops_82598 = {
+ .init_params = &ixgbe_init_eeprom_params_generic,
+ .read = &ixgbe_read_eerd_generic,
+ .validate_checksum = &ixgbe_validate_eeprom_checksum_generic,
+ .update_checksum = &ixgbe_update_eeprom_checksum_generic,
+};
+
+static struct ixgbe_phy_operations phy_ops_82598 = {
+ .identify = &ixgbe_identify_phy_generic,
+ .identify_sfp = &ixgbe_identify_sfp_module_generic,
+ .init = &ixgbe_init_phy_ops_82598,
+ .reset = &ixgbe_reset_phy_generic,
+ .read_reg = &ixgbe_read_phy_reg_generic,
+ .write_reg = &ixgbe_write_phy_reg_generic,
+ .setup_link = &ixgbe_setup_phy_link_generic,
+ .setup_link_speed = &ixgbe_setup_phy_link_speed_generic,
+ .read_i2c_eeprom = &ixgbe_read_i2c_eeprom_82598,
+ .check_overtemp = &ixgbe_tn_check_overtemp,
};
struct ixgbe_info ixgbe_82598_info = {
.mac = ixgbe_mac_82598EB,
.get_invariants = &ixgbe_get_invariants_82598,
.mac_ops = &mac_ops_82598,
+ .eeprom_ops = &eeprom_ops_82598,
+ .phy_ops = &phy_ops_82598,
};