static void hpp_io_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr,
int ring_page);
-\f
+
/* Probe a list of addresses for an HP LAN+ adaptor.
This routine is almost boilerplate. */
int base_addr = dev->base_addr;
int irq = dev->irq;
- SET_MODULE_OWNER(dev);
-
if (base_addr > 0x1ff) /* Check a single specified location. */
return hpp_probe1(dev, base_addr);
else if (base_addr != 0) /* Don't probe at all. */
#ifndef MODULE
struct net_device * __init hp_plus_probe(int unit)
{
- struct net_device *dev = alloc_ei_netdev();
+ struct net_device *dev = alloc_eip_netdev();
int err;
if (!dev)
}
#endif
+static const struct net_device_ops hpp_netdev_ops = {
+ .ndo_open = hpp_open,
+ .ndo_stop = hpp_close,
+ .ndo_start_xmit = eip_start_xmit,
+ .ndo_tx_timeout = eip_tx_timeout,
+ .ndo_get_stats = eip_get_stats,
+ .ndo_set_multicast_list = eip_set_multicast_list,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_set_mac_address = eth_mac_addr,
+ .ndo_change_mtu = eth_change_mtu,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ .ndo_poll_controller = eip_poll,
+#endif
+};
+
+
/* Do the interesting part of the probe at a single address. */
static int __init hpp_probe1(struct net_device *dev, int ioaddr)
{
return -EBUSY;
/* Check for the HP+ signature, 50 48 0x 53. */
- if (inw(ioaddr + HP_ID) != 0x4850
- || (inw(ioaddr + HP_PAGING) & 0xfff0) != 0x5300) {
+ if (inw(ioaddr + HP_ID) != 0x4850 ||
+ (inw(ioaddr + HP_PAGING) & 0xfff0) != 0x5300) {
retval = -ENODEV;
goto out;
}
if (ei_debug && version_printed++ == 0)
printk(version);
- printk("%s: %s at %#3x,", dev->name, name, ioaddr);
+ printk("%s: %s at %#3x, ", dev->name, name, ioaddr);
/* Retrieve and checksum the station address. */
outw(MAC_Page, ioaddr + HP_PAGING);
unsigned char inval = inb(ioaddr + 8 + i);
dev->dev_addr[i] = inval;
checksum += inval;
- printk(" %2.2x", inval);
}
checksum += inb(ioaddr + 14);
+ printk("%pM", dev->dev_addr);
+
if (checksum != 0xff) {
printk(" bad checksum %2.2x.\n", checksum);
retval = -ENODEV;
/* Set the base address to point to the NIC, not the "real" base! */
dev->base_addr = ioaddr + NIC_OFFSET;
- dev->open = &hpp_open;
- dev->stop = &hpp_close;
-#ifdef CONFIG_NET_POLL_CONTROLLER
- dev->poll_controller = ei_poll;
-#endif
+ dev->netdev_ops = &hpp_netdev_ops;
ei_status.name = name;
ei_status.word16 = 0; /* Agggghhhhh! Debug time: 2 days! */
}
outw(Perf_Page, ioaddr + HP_PAGING);
- NS8390_init(dev, 0);
+ NS8390p_init(dev, 0);
/* Leave the 8390 and HP chip reset. */
outw(inw(ioaddr + HPP_OPTION) & ~EnableIRQ, ioaddr + HPP_OPTION);
int option_reg;
int retval;
- if ((retval = request_irq(dev->irq, ei_interrupt, 0, dev->name, dev))) {
+ if ((retval = request_irq(dev->irq, eip_interrupt, 0, dev->name, dev))) {
return retval;
}
/* Select the operational page. */
outw(Perf_Page, ioaddr + HP_PAGING);
- ei_open(dev);
- return 0;
+ return eip_open(dev);
}
static int
int option_reg = inw(ioaddr + HPP_OPTION);
free_irq(dev->irq, dev);
- ei_close(dev);
+ eip_close(dev);
outw((option_reg & ~EnableIRQ) | MemDisable | NICReset | ChipReset,
ioaddr + HPP_OPTION);
return;
}
-\f
+
#ifdef MODULE
#define MAX_HPP_CARDS 4 /* Max number of HPP cards per module */
static struct net_device *dev_hpp[MAX_HPP_CARDS];
if (this_dev != 0) break; /* only autoprobe 1st one */
printk(KERN_NOTICE "hp-plus.c: Presently autoprobing (not recommended) for a single card.\n");
}
- dev = alloc_ei_netdev();
+ dev = alloc_eip_netdev();
if (!dev)
break;
dev->irq = irq[this_dev];
release_region(dev->base_addr - NIC_OFFSET, HP_IO_EXTENT);
}
-void
+void __exit
cleanup_module(void)
{
int this_dev;