/*******************************************************************************
Intel PRO/1000 Linux driver
- Copyright(c) 1999 - 2008 Intel Corporation.
+ Copyright(c) 1999 - 2009 Intel Corporation.
This program is free software; you can redistribute it and/or modify it
under the terms and conditions of the GNU General Public License,
static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw);
static s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active);
static s32 e1000_wait_autoneg(struct e1000_hw *hw);
+static u32 e1000_get_phy_addr_for_bm_page(u32 page, u32 reg);
+static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
+ u16 *data, bool read);
+static u32 e1000_get_phy_addr_for_hv_page(u32 page);
+static s32 e1000_access_phy_debug_regs_hv(struct e1000_hw *hw, u32 offset,
+ u16 *data, bool read);
/* Cable length tables */
static const u16 e1000_m88_cable_length_table[] =
{ 0, 50, 80, 110, 140, 140, E1000_CABLE_LENGTH_UNDEFINED };
+#define M88E1000_CABLE_LENGTH_TABLE_SIZE \
+ ARRAY_SIZE(e1000_m88_cable_length_table)
static const u16 e1000_igp_2_cable_length_table[] =
{ 0, 0, 0, 0, 0, 0, 0, 0, 3, 5, 8, 11, 13, 16, 18, 21, 0, 0, 0, 3,
#define IGP02E1000_CABLE_LENGTH_TABLE_SIZE \
ARRAY_SIZE(e1000_igp_2_cable_length_table)
+#define BM_PHY_REG_PAGE(offset) \
+ ((u16)(((offset) >> PHY_PAGE_SHIFT) & 0xFFFF))
+#define BM_PHY_REG_NUM(offset) \
+ ((u16)(((offset) & MAX_PHY_REG_ADDRESS) |\
+ (((offset) >> (PHY_UPPER_SHIFT - PHY_PAGE_SHIFT)) &\
+ ~MAX_PHY_REG_ADDRESS)))
+
+#define HV_INTC_FC_PAGE_START 768
+#define I82578_ADDR_REG 29
+#define I82577_ADDR_REG 16
+#define I82577_CFG_REG 22
+#define I82577_CFG_ASSERT_CRS_ON_TX (1 << 15)
+#define I82577_CFG_ENABLE_DOWNSHIFT (3 << 10) /* auto downshift 100/10 */
+#define I82577_CTRL_REG 23
+
+/* 82577 specific PHY registers */
+#define I82577_PHY_CTRL_2 18
+#define I82577_PHY_STATUS_2 26
+#define I82577_PHY_DIAG_STATUS 31
+
+/* I82577 PHY Status 2 */
+#define I82577_PHY_STATUS2_REV_POLARITY 0x0400
+#define I82577_PHY_STATUS2_MDIX 0x0800
+#define I82577_PHY_STATUS2_SPEED_MASK 0x0300
+#define I82577_PHY_STATUS2_SPEED_1000MBPS 0x0200
+
+/* I82577 PHY Control 2 */
+#define I82577_PHY_CTRL2_AUTO_MDIX 0x0400
+#define I82577_PHY_CTRL2_FORCE_MDI_MDIX 0x0200
+
+/* I82577 PHY Diagnostics Status */
+#define I82577_DSTATUS_CABLE_LENGTH 0x03FC
+#define I82577_DSTATUS_CABLE_LENGTH_SHIFT 2
+
+/* BM PHY Copper Specific Control 1 */
+#define BM_CS_CTRL1 16
+
+#define HV_MUX_DATA_CTRL PHY_REG(776, 16)
+#define HV_MUX_DATA_CTRL_GEN_TO_MAC 0x0400
+#define HV_MUX_DATA_CTRL_FORCE_SPEED 0x0004
+
/**
* e1000e_check_reset_block_generic - Check if PHY reset is blocked
* @hw: pointer to the HW structure
s32 e1000e_get_phy_id(struct e1000_hw *hw)
{
struct e1000_phy_info *phy = &hw->phy;
- s32 ret_val;
+ s32 ret_val = 0;
u16 phy_id;
+ u16 retry_count = 0;
- ret_val = e1e_rphy(hw, PHY_ID1, &phy_id);
- if (ret_val)
- return ret_val;
+ if (!(phy->ops.read_reg))
+ goto out;
- phy->id = (u32)(phy_id << 16);
- udelay(20);
- ret_val = e1e_rphy(hw, PHY_ID2, &phy_id);
- if (ret_val)
- return ret_val;
+ while (retry_count < 2) {
+ ret_val = e1e_rphy(hw, PHY_ID1, &phy_id);
+ if (ret_val)
+ goto out;
- phy->id |= (u32)(phy_id & PHY_REVISION_MASK);
- phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK);
+ phy->id = (u32)(phy_id << 16);
+ udelay(20);
+ ret_val = e1e_rphy(hw, PHY_ID2, &phy_id);
+ if (ret_val)
+ goto out;
- return 0;
+ phy->id |= (u32)(phy_id & PHY_REVISION_MASK);
+ phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK);
+
+ if (phy->id != 0 && phy->id != PHY_REVISION_MASK)
+ goto out;
+
+ /*
+ * If the PHY ID is still unknown, we may have an 82577
+ * without link. We will try again after setting Slow MDIC
+ * mode. No harm in trying again in this case since the PHY
+ * ID is unknown at this point anyway.
+ */
+ ret_val = phy->ops.acquire(hw);
+ if (ret_val)
+ goto out;
+ ret_val = e1000_set_mdio_slow_mode_hv(hw, true);
+ if (ret_val)
+ goto out;
+ phy->ops.release(hw);
+
+ retry_count++;
+ }
+out:
+ /* Revert to MDIO fast mode, if applicable */
+ if (retry_count) {
+ ret_val = phy->ops.acquire(hw);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_set_mdio_slow_mode_hv(hw, false);
+ phy->ops.release(hw);
+ }
+
+ return ret_val;
}
/**
u32 i, mdic = 0;
if (offset > MAX_PHY_REG_ADDRESS) {
- hw_dbg(hw, "PHY Address %d is out of range\n", offset);
+ e_dbg("PHY Address %d is out of range\n", offset);
return -E1000_ERR_PARAM;
}
break;
}
if (!(mdic & E1000_MDIC_READY)) {
- hw_dbg(hw, "MDI Read did not complete\n");
+ e_dbg("MDI Read did not complete\n");
return -E1000_ERR_PHY;
}
if (mdic & E1000_MDIC_ERROR) {
- hw_dbg(hw, "MDI Error\n");
+ e_dbg("MDI Error\n");
return -E1000_ERR_PHY;
}
*data = (u16) mdic;
u32 i, mdic = 0;
if (offset > MAX_PHY_REG_ADDRESS) {
- hw_dbg(hw, "PHY Address %d is out of range\n", offset);
+ e_dbg("PHY Address %d is out of range\n", offset);
return -E1000_ERR_PARAM;
}
break;
}
if (!(mdic & E1000_MDIC_READY)) {
- hw_dbg(hw, "MDI Write did not complete\n");
+ e_dbg("MDI Write did not complete\n");
return -E1000_ERR_PHY;
}
if (mdic & E1000_MDIC_ERROR) {
- hw_dbg(hw, "MDI Error\n");
+ e_dbg("MDI Error\n");
return -E1000_ERR_PHY;
}
{
s32 ret_val;
- ret_val = hw->phy.ops.acquire_phy(hw);
+ ret_val = hw->phy.ops.acquire(hw);
if (ret_val)
return ret_val;
ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
data);
- hw->phy.ops.release_phy(hw);
+ hw->phy.ops.release(hw);
return ret_val;
}
{
s32 ret_val;
- ret_val = hw->phy.ops.acquire_phy(hw);
+ ret_val = hw->phy.ops.acquire(hw);
if (ret_val)
return ret_val;
ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
data);
- hw->phy.ops.release_phy(hw);
+ hw->phy.ops.release(hw);
return ret_val;
}
/**
- * e1000e_read_phy_reg_igp - Read igp PHY register
+ * __e1000e_read_phy_reg_igp - Read igp PHY register
* @hw: pointer to the HW structure
* @offset: register offset to be read
* @data: pointer to the read data
+ * @locked: semaphore has already been acquired or not
*
* Acquires semaphore, if necessary, then reads the PHY register at offset
- * and storing the retrieved information in data. Release any acquired
+ * and stores the retrieved information in data. Release any acquired
* semaphores before exiting.
**/
-s32 e1000e_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data)
+static s32 __e1000e_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data,
+ bool locked)
{
- s32 ret_val;
+ s32 ret_val = 0;
- ret_val = hw->phy.ops.acquire_phy(hw);
- if (ret_val)
- return ret_val;
+ if (!locked) {
+ if (!(hw->phy.ops.acquire))
+ goto out;
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
+ }
if (offset > MAX_PHY_MULTI_PAGE_REG) {
ret_val = e1000e_write_phy_reg_mdic(hw,
IGP01E1000_PHY_PAGE_SELECT,
(u16)offset);
- if (ret_val) {
- hw->phy.ops.release_phy(hw);
- return ret_val;
- }
+ if (ret_val)
+ goto release;
}
ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
- data);
-
- hw->phy.ops.release_phy(hw);
+ data);
+release:
+ if (!locked)
+ hw->phy.ops.release(hw);
+out:
return ret_val;
}
/**
+ * e1000e_read_phy_reg_igp - Read igp PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Acquires semaphore then reads the PHY register at offset and stores the
+ * retrieved information in data.
+ * Release the acquired semaphore before exiting.
+ **/
+s32 e1000e_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ return __e1000e_read_phy_reg_igp(hw, offset, data, false);
+}
+
+/**
+ * e1000e_read_phy_reg_igp_locked - Read igp PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Reads the PHY register at offset and stores the retrieved information
+ * in data. Assumes semaphore already acquired.
+ **/
+s32 e1000e_read_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ return __e1000e_read_phy_reg_igp(hw, offset, data, true);
+}
+
+/**
* e1000e_write_phy_reg_igp - Write igp PHY register
* @hw: pointer to the HW structure
* @offset: register offset to write to
* @data: data to write at register offset
+ * @locked: semaphore has already been acquired or not
*
* Acquires semaphore, if necessary, then writes the data to PHY register
* at the offset. Release any acquired semaphores before exiting.
**/
-s32 e1000e_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data)
+static s32 __e1000e_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data,
+ bool locked)
{
- s32 ret_val;
+ s32 ret_val = 0;
- ret_val = hw->phy.ops.acquire_phy(hw);
- if (ret_val)
- return ret_val;
+ if (!locked) {
+ if (!(hw->phy.ops.acquire))
+ goto out;
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
+ }
if (offset > MAX_PHY_MULTI_PAGE_REG) {
ret_val = e1000e_write_phy_reg_mdic(hw,
IGP01E1000_PHY_PAGE_SELECT,
(u16)offset);
- if (ret_val) {
- hw->phy.ops.release_phy(hw);
- return ret_val;
- }
+ if (ret_val)
+ goto release;
}
ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
data);
- hw->phy.ops.release_phy(hw);
+release:
+ if (!locked)
+ hw->phy.ops.release(hw);
+out:
return ret_val;
}
/**
- * e1000e_read_kmrn_reg - Read kumeran register
+ * e1000e_write_phy_reg_igp - Write igp PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Acquires semaphore then writes the data to PHY register
+ * at the offset. Release any acquired semaphores before exiting.
+ **/
+s32 e1000e_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ return __e1000e_write_phy_reg_igp(hw, offset, data, false);
+}
+
+/**
+ * e1000e_write_phy_reg_igp_locked - Write igp PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Writes the data to PHY register at the offset.
+ * Assumes semaphore already acquired.
+ **/
+s32 e1000e_write_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ return __e1000e_write_phy_reg_igp(hw, offset, data, true);
+}
+
+/**
+ * __e1000_read_kmrn_reg - Read kumeran register
* @hw: pointer to the HW structure
* @offset: register offset to be read
* @data: pointer to the read data
+ * @locked: semaphore has already been acquired or not
*
* Acquires semaphore, if necessary. Then reads the PHY register at offset
* using the kumeran interface. The information retrieved is stored in data.
* Release any acquired semaphores before exiting.
**/
-s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data)
+static s32 __e1000_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data,
+ bool locked)
{
u32 kmrnctrlsta;
- s32 ret_val;
+ s32 ret_val = 0;
- ret_val = hw->phy.ops.acquire_phy(hw);
- if (ret_val)
- return ret_val;
+ if (!locked) {
+ if (!(hw->phy.ops.acquire))
+ goto out;
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
+ }
kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) &
E1000_KMRNCTRLSTA_OFFSET) | E1000_KMRNCTRLSTA_REN;
kmrnctrlsta = er32(KMRNCTRLSTA);
*data = (u16)kmrnctrlsta;
- hw->phy.ops.release_phy(hw);
+ if (!locked)
+ hw->phy.ops.release(hw);
+out:
return ret_val;
}
/**
- * e1000e_write_kmrn_reg - Write kumeran register
+ * e1000e_read_kmrn_reg - Read kumeran register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Acquires semaphore then reads the PHY register at offset using the
+ * kumeran interface. The information retrieved is stored in data.
+ * Release the acquired semaphore before exiting.
+ **/
+s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ return __e1000_read_kmrn_reg(hw, offset, data, false);
+}
+
+/**
+ * e1000e_read_kmrn_reg_locked - Read kumeran register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Reads the PHY register at offset using the kumeran interface. The
+ * information retrieved is stored in data.
+ * Assumes semaphore already acquired.
+ **/
+s32 e1000e_read_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ return __e1000_read_kmrn_reg(hw, offset, data, true);
+}
+
+/**
+ * __e1000_write_kmrn_reg - Write kumeran register
* @hw: pointer to the HW structure
* @offset: register offset to write to
* @data: data to write at register offset
+ * @locked: semaphore has already been acquired or not
*
* Acquires semaphore, if necessary. Then write the data to PHY register
* at the offset using the kumeran interface. Release any acquired semaphores
* before exiting.
**/
-s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data)
+static s32 __e1000_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data,
+ bool locked)
{
u32 kmrnctrlsta;
- s32 ret_val;
+ s32 ret_val = 0;
- ret_val = hw->phy.ops.acquire_phy(hw);
- if (ret_val)
- return ret_val;
+ if (!locked) {
+ if (!(hw->phy.ops.acquire))
+ goto out;
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
+ }
kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) &
E1000_KMRNCTRLSTA_OFFSET) | data;
ew32(KMRNCTRLSTA, kmrnctrlsta);
udelay(2);
- hw->phy.ops.release_phy(hw);
+ if (!locked)
+ hw->phy.ops.release(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_write_kmrn_reg - Write kumeran register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Acquires semaphore then writes the data to the PHY register at the offset
+ * using the kumeran interface. Release the acquired semaphore before exiting.
+ **/
+s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ return __e1000_write_kmrn_reg(hw, offset, data, false);
+}
+
+/**
+ * e1000e_write_kmrn_reg_locked - Write kumeran register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Write the data to PHY register at the offset using the kumeran interface.
+ * Assumes semaphore already acquired.
+ **/
+s32 e1000e_write_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ return __e1000_write_kmrn_reg(hw, offset, data, true);
+}
+
+/**
+ * e1000_copper_link_setup_82577 - Setup 82577 PHY for copper link
+ * @hw: pointer to the HW structure
+ *
+ * Sets up Carrier-sense on Transmit and downshift values.
+ **/
+s32 e1000_copper_link_setup_82577(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data;
+
+ /* Enable CRS on TX. This must be set for half-duplex operation. */
+ ret_val = phy->ops.read_reg(hw, I82577_CFG_REG, &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy_data |= I82577_CFG_ASSERT_CRS_ON_TX;
+
+ /* Enable downshift */
+ phy_data |= I82577_CFG_ENABLE_DOWNSHIFT;
+
+ ret_val = phy->ops.write_reg(hw, I82577_CFG_REG, phy_data);
+
+out:
return ret_val;
}
if (ret_val)
return ret_val;
- /* For newer PHYs this bit is downshift enable */
- if (phy->type == e1000_phy_m88)
+ /* For BM PHY this bit is downshift enable */
+ if (phy->type != e1000_phy_bm)
phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
/*
if (phy->disable_polarity_correction == 1)
phy_data |= M88E1000_PSCR_POLARITY_REVERSAL;
+ /* Enable downshift on BM (disabled by default) */
+ if (phy->type == e1000_phy_bm)
+ phy_data |= BME1000_PSCR_ENABLE_DOWNSHIFT;
+
ret_val = e1e_wphy(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
if (ret_val)
return ret_val;
- if ((phy->type == e1000_phy_m88) && (phy->revision < 4)) {
+ if ((phy->type == e1000_phy_m88) &&
+ (phy->revision < E1000_REVISION_4) &&
+ (phy->id != BME1000_E_PHY_ID_R2)) {
/*
* Force TX_CLK in the Extended PHY Specific Control Register
* to 25MHz clock.
return ret_val;
}
+ if ((phy->type == e1000_phy_bm) && (phy->id == BME1000_E_PHY_ID_R2)) {
+ /* Set PHY page 0, register 29 to 0x0003 */
+ ret_val = e1e_wphy(hw, 29, 0x0003);
+ if (ret_val)
+ return ret_val;
+
+ /* Set PHY page 0, register 30 to 0x0000 */
+ ret_val = e1e_wphy(hw, 30, 0x0000);
+ if (ret_val)
+ return ret_val;
+ }
+
/* Commit the changes. */
ret_val = e1000e_commit_phy(hw);
- if (ret_val)
- hw_dbg(hw, "Error committing the PHY changes\n");
+ if (ret_val) {
+ e_dbg("Error committing the PHY changes\n");
+ return ret_val;
+ }
- return ret_val;
+ if (phy->type == e1000_phy_82578) {
+ ret_val = phy->ops.read_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* 82578 PHY - set the downshift count to 1x. */
+ phy_data |= I82578_EPSCR_DOWNSHIFT_ENABLE;
+ phy_data &= ~I82578_EPSCR_DOWNSHIFT_COUNTER_MASK;
+ ret_val = phy->ops.write_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ return 0;
}
/**
ret_val = e1000_phy_hw_reset(hw);
if (ret_val) {
- hw_dbg(hw, "Error resetting the PHY.\n");
+ e_dbg("Error resetting the PHY.\n");
return ret_val;
}
msleep(100);
/* disable lplu d0 during driver init */
- ret_val = e1000_set_d0_lplu_state(hw, 0);
+ ret_val = e1000_set_d0_lplu_state(hw, false);
if (ret_val) {
- hw_dbg(hw, "Error Disabling LPLU D0\n");
+ e_dbg("Error Disabling LPLU D0\n");
return ret_val;
}
/* Configure mdi-mdix settings */
NWAY_AR_10T_HD_CAPS);
mii_1000t_ctrl_reg &= ~(CR_1000T_HD_CAPS | CR_1000T_FD_CAPS);
- hw_dbg(hw, "autoneg_advertised %x\n", phy->autoneg_advertised);
+ e_dbg("autoneg_advertised %x\n", phy->autoneg_advertised);
/* Do we want to advertise 10 Mb Half Duplex? */
if (phy->autoneg_advertised & ADVERTISE_10_HALF) {
- hw_dbg(hw, "Advertise 10mb Half duplex\n");
+ e_dbg("Advertise 10mb Half duplex\n");
mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
}
/* Do we want to advertise 10 Mb Full Duplex? */
if (phy->autoneg_advertised & ADVERTISE_10_FULL) {
- hw_dbg(hw, "Advertise 10mb Full duplex\n");
+ e_dbg("Advertise 10mb Full duplex\n");
mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS;
}
/* Do we want to advertise 100 Mb Half Duplex? */
if (phy->autoneg_advertised & ADVERTISE_100_HALF) {
- hw_dbg(hw, "Advertise 100mb Half duplex\n");
+ e_dbg("Advertise 100mb Half duplex\n");
mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS;
}
/* Do we want to advertise 100 Mb Full Duplex? */
if (phy->autoneg_advertised & ADVERTISE_100_FULL) {
- hw_dbg(hw, "Advertise 100mb Full duplex\n");
+ e_dbg("Advertise 100mb Full duplex\n");
mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS;
}
/* We do not allow the Phy to advertise 1000 Mb Half Duplex */
if (phy->autoneg_advertised & ADVERTISE_1000_HALF)
- hw_dbg(hw, "Advertise 1000mb Half duplex request denied!\n");
+ e_dbg("Advertise 1000mb Half duplex request denied!\n");
/* Do we want to advertise 1000 Mb Full Duplex? */
if (phy->autoneg_advertised & ADVERTISE_1000_FULL) {
- hw_dbg(hw, "Advertise 1000mb Full duplex\n");
+ e_dbg("Advertise 1000mb Full duplex\n");
mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
}
* other: No software override. The flow control configuration
* in the EEPROM is used.
*/
- switch (hw->fc.type) {
+ switch (hw->fc.current_mode) {
case e1000_fc_none:
/*
* Flow control (Rx & Tx) is completely disabled by a
mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
break;
default:
- hw_dbg(hw, "Flow control param set incorrectly\n");
+ e_dbg("Flow control param set incorrectly\n");
ret_val = -E1000_ERR_CONFIG;
return ret_val;
}
if (ret_val)
return ret_val;
- hw_dbg(hw, "Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
+ e_dbg("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
if (phy->autoneg_mask & ADVERTISE_1000_FULL) {
ret_val = e1e_wphy(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg);
if (phy->autoneg_advertised == 0)
phy->autoneg_advertised = phy->autoneg_mask;
- hw_dbg(hw, "Reconfiguring auto-neg advertisement params\n");
+ e_dbg("Reconfiguring auto-neg advertisement params\n");
ret_val = e1000_phy_setup_autoneg(hw);
if (ret_val) {
- hw_dbg(hw, "Error Setting up Auto-Negotiation\n");
+ e_dbg("Error Setting up Auto-Negotiation\n");
return ret_val;
}
- hw_dbg(hw, "Restarting Auto-Neg\n");
+ e_dbg("Restarting Auto-Neg\n");
/*
* Restart auto-negotiation by setting the Auto Neg Enable bit and
if (phy->autoneg_wait_to_complete) {
ret_val = e1000_wait_autoneg(hw);
if (ret_val) {
- hw_dbg(hw, "Error while waiting for "
+ e_dbg("Error while waiting for "
"autoneg to complete\n");
return ret_val;
}
* PHY will be set to 10H, 10F, 100H or 100F
* depending on user settings.
*/
- hw_dbg(hw, "Forcing Speed and Duplex\n");
+ e_dbg("Forcing Speed and Duplex\n");
ret_val = e1000_phy_force_speed_duplex(hw);
if (ret_val) {
- hw_dbg(hw, "Error Forcing Speed and Duplex\n");
+ e_dbg("Error Forcing Speed and Duplex\n");
return ret_val;
}
}
return ret_val;
if (link) {
- hw_dbg(hw, "Valid link established!!!\n");
+ e_dbg("Valid link established!!!\n");
e1000e_config_collision_dist(hw);
ret_val = e1000e_config_fc_after_link_up(hw);
} else {
- hw_dbg(hw, "Unable to establish link!!!\n");
+ e_dbg("Unable to establish link!!!\n");
}
return ret_val;
if (ret_val)
return ret_val;
- hw_dbg(hw, "IGP PSCR: %X\n", phy_data);
+ e_dbg("IGP PSCR: %X\n", phy_data);
udelay(1);
if (phy->autoneg_wait_to_complete) {
- hw_dbg(hw, "Waiting for forced speed/duplex link on IGP phy.\n");
+ e_dbg("Waiting for forced speed/duplex link on IGP phy.\n");
ret_val = e1000e_phy_has_link_generic(hw,
PHY_FORCE_LIMIT,
return ret_val;
if (!link)
- hw_dbg(hw, "Link taking longer than expected.\n");
+ e_dbg("Link taking longer than expected.\n");
/* Try once more */
ret_val = e1000e_phy_has_link_generic(hw,
if (ret_val)
return ret_val;
- hw_dbg(hw, "M88E1000 PSCR: %X\n", phy_data);
+ e_dbg("M88E1000 PSCR: %X\n", phy_data);
ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_data);
if (ret_val)
e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
- /* Reset the phy to commit changes. */
- phy_data |= MII_CR_RESET;
-
ret_val = e1e_wphy(hw, PHY_CONTROL, phy_data);
if (ret_val)
return ret_val;
- udelay(1);
+ /* Reset the phy to commit changes. */
+ ret_val = e1000e_commit_phy(hw);
+ if (ret_val)
+ return ret_val;
if (phy->autoneg_wait_to_complete) {
- hw_dbg(hw, "Waiting for forced speed/duplex link on M88 phy.\n");
+ e_dbg("Waiting for forced speed/duplex link on M88 phy.\n");
ret_val = e1000e_phy_has_link_generic(hw, PHY_FORCE_LIMIT,
100000, &link);
return ret_val;
if (!link) {
- /*
- * We didn't get link.
- * Reset the DSP and cross our fingers.
- */
- ret_val = e1e_wphy(hw, M88E1000_PHY_PAGE_SELECT,
- 0x001d);
- if (ret_val)
- return ret_val;
- ret_val = e1000e_phy_reset_dsp(hw);
- if (ret_val)
- return ret_val;
+ if (hw->phy.type != e1000_phy_m88) {
+ e_dbg("Link taking longer than expected.\n");
+ } else {
+ /*
+ * We didn't get link.
+ * Reset the DSP and cross our fingers.
+ */
+ ret_val = e1e_wphy(hw,
+ M88E1000_PHY_PAGE_SELECT,
+ 0x001d);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000e_phy_reset_dsp(hw);
+ if (ret_val)
+ return ret_val;
+ }
}
/* Try once more */
return ret_val;
}
+ if (hw->phy.type != e1000_phy_m88)
+ return 0;
+
ret_val = e1e_rphy(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data);
if (ret_val)
return ret_val;
}
/**
+ * e1000_phy_force_speed_duplex_ife - Force PHY speed & duplex
+ * @hw: pointer to the HW structure
+ *
+ * Forces the speed and duplex settings of the PHY.
+ * This is a function pointer entry point only called by
+ * PHY setup routines.
+ **/
+s32 e1000_phy_force_speed_duplex_ife(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+ bool link;
+
+ ret_val = e1e_rphy(hw, PHY_CONTROL, &data);
+ if (ret_val)
+ goto out;
+
+ e1000e_phy_force_speed_duplex_setup(hw, &data);
+
+ ret_val = e1e_wphy(hw, PHY_CONTROL, data);
+ if (ret_val)
+ goto out;
+
+ /* Disable MDI-X support for 10/100 */
+ ret_val = e1e_rphy(hw, IFE_PHY_MDIX_CONTROL, &data);
+ if (ret_val)
+ goto out;
+
+ data &= ~IFE_PMC_AUTO_MDIX;
+ data &= ~IFE_PMC_FORCE_MDIX;
+
+ ret_val = e1e_wphy(hw, IFE_PHY_MDIX_CONTROL, data);
+ if (ret_val)
+ goto out;
+
+ e_dbg("IFE PMC: %X\n", data);
+
+ udelay(1);
+
+ if (phy->autoneg_wait_to_complete) {
+ e_dbg("Waiting for forced speed/duplex link on IFE phy.\n");
+
+ ret_val = e1000e_phy_has_link_generic(hw,
+ PHY_FORCE_LIMIT,
+ 100000,
+ &link);
+ if (ret_val)
+ goto out;
+
+ if (!link)
+ e_dbg("Link taking longer than expected.\n");
+
+ /* Try once more */
+ ret_val = e1000e_phy_has_link_generic(hw,
+ PHY_FORCE_LIMIT,
+ 100000,
+ &link);
+ if (ret_val)
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
* e1000e_phy_force_speed_duplex_setup - Configure forced PHY speed/duplex
* @hw: pointer to the HW structure
* @phy_ctrl: pointer to current value of PHY_CONTROL
u32 ctrl;
/* Turn off flow control when forcing speed/duplex */
- hw->fc.type = e1000_fc_none;
+ hw->fc.current_mode = e1000_fc_none;
/* Force speed/duplex on the mac */
ctrl = er32(CTRL);
if (mac->forced_speed_duplex & E1000_ALL_HALF_DUPLEX) {
ctrl &= ~E1000_CTRL_FD;
*phy_ctrl &= ~MII_CR_FULL_DUPLEX;
- hw_dbg(hw, "Half Duplex\n");
+ e_dbg("Half Duplex\n");
} else {
ctrl |= E1000_CTRL_FD;
*phy_ctrl |= MII_CR_FULL_DUPLEX;
- hw_dbg(hw, "Full Duplex\n");
+ e_dbg("Full Duplex\n");
}
/* Forcing 10mb or 100mb? */
ctrl |= E1000_CTRL_SPD_100;
*phy_ctrl |= MII_CR_SPEED_100;
*phy_ctrl &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_10);
- hw_dbg(hw, "Forcing 100mb\n");
+ e_dbg("Forcing 100mb\n");
} else {
ctrl &= ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100);
*phy_ctrl |= MII_CR_SPEED_10;
*phy_ctrl &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_100);
- hw_dbg(hw, "Forcing 10mb\n");
+ e_dbg("Forcing 10mb\n");
}
e1000e_config_collision_dist(hw);
switch (phy->type) {
case e1000_phy_m88:
case e1000_phy_gg82563:
+ case e1000_phy_bm:
+ case e1000_phy_82578:
offset = M88E1000_PHY_SPEC_STATUS;
mask = M88E1000_PSSR_DOWNSHIFT;
break;
break;
default:
/* speed downshift not supported */
- phy->speed_downgraded = 0;
+ phy->speed_downgraded = false;
return 0;
}
*
* Polarity is determined based on the PHY specific status register.
**/
-static s32 e1000_check_polarity_m88(struct e1000_hw *hw)
+s32 e1000_check_polarity_m88(struct e1000_hw *hw)
{
struct e1000_phy_info *phy = &hw->phy;
s32 ret_val;
* Polarity is determined based on the PHY port status register, and the
* current speed (since there is no polarity at 100Mbps).
**/
-static s32 e1000_check_polarity_igp(struct e1000_hw *hw)
+s32 e1000_check_polarity_igp(struct e1000_hw *hw)
{
struct e1000_phy_info *phy = &hw->phy;
s32 ret_val;
}
/**
- * e1000_wait_autoneg - Wait for auto-neg completion
+ * e1000_check_polarity_ife - Check cable polarity for IFE PHY
* @hw: pointer to the HW structure
*
- * Waits for auto-negotiation to complete or for the auto-negotiation time
- * limit to expire, which ever happens first.
+ * Polarity is determined on the polarity reversal feature being enabled.
**/
-static s32 e1000_wait_autoneg(struct e1000_hw *hw)
+s32 e1000_check_polarity_ife(struct e1000_hw *hw)
{
- s32 ret_val = 0;
- u16 i, phy_status;
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data, offset, mask;
- /* Break after autoneg completes or PHY_AUTO_NEG_LIMIT expires. */
- for (i = PHY_AUTO_NEG_LIMIT; i > 0; i--) {
- ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
- if (ret_val)
- break;
- ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
- if (ret_val)
- break;
- if (phy_status & MII_SR_AUTONEG_COMPLETE)
+ /*
+ * Polarity is determined based on the reversal feature being enabled.
+ */
+ if (phy->polarity_correction) {
+ offset = IFE_PHY_EXTENDED_STATUS_CONTROL;
+ mask = IFE_PESC_POLARITY_REVERSED;
+ } else {
+ offset = IFE_PHY_SPECIAL_CONTROL;
+ mask = IFE_PSC_FORCE_POLARITY;
+ }
+
+ ret_val = e1e_rphy(hw, offset, &phy_data);
+
+ if (!ret_val)
+ phy->cable_polarity = (phy_data & mask)
+ ? e1000_rev_polarity_reversed
+ : e1000_rev_polarity_normal;
+
+ return ret_val;
+}
+
+/**
+ * e1000_wait_autoneg - Wait for auto-neg completion
+ * @hw: pointer to the HW structure
+ *
+ * Waits for auto-negotiation to complete or for the auto-negotiation time
+ * limit to expire, which ever happens first.
+ **/
+static s32 e1000_wait_autoneg(struct e1000_hw *hw)
+{
+ s32 ret_val = 0;
+ u16 i, phy_status;
+
+ /* Break after autoneg completes or PHY_AUTO_NEG_LIMIT expires. */
+ for (i = PHY_AUTO_NEG_LIMIT; i > 0; i--) {
+ ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
+ if (ret_val)
+ break;
+ ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
+ if (ret_val)
+ break;
+ if (phy_status & MII_SR_AUTONEG_COMPLETE)
break;
msleep(100);
}
*/
ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
if (ret_val)
- break;
+ /*
+ * If the first read fails, another entity may have
+ * ownership of the resources, wait and try again to
+ * see if they have relinquished the resources yet.
+ */
+ udelay(usec_interval);
ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
if (ret_val)
break;
ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
if (ret_val)
- return ret_val;
+ goto out;
index = (phy_data & M88E1000_PSSR_CABLE_LENGTH) >>
- M88E1000_PSSR_CABLE_LENGTH_SHIFT;
+ M88E1000_PSSR_CABLE_LENGTH_SHIFT;
+ if (index >= M88E1000_CABLE_LENGTH_TABLE_SIZE - 1) {
+ ret_val = -E1000_ERR_PHY;
+ goto out;
+ }
+
phy->min_cable_length = e1000_m88_cable_length_table[index];
- phy->max_cable_length = e1000_m88_cable_length_table[index+1];
+ phy->max_cable_length = e1000_m88_cable_length_table[index + 1];
phy->cable_length = (phy->min_cable_length + phy->max_cable_length) / 2;
+out:
return ret_val;
}
* The automatic gain control (agc) normalizes the amplitude of the
* received signal, adjusting for the attenuation produced by the
* cable. By reading the AGC registers, which represent the
- * combination of course and fine gain value, the value can be put
+ * combination of coarse and fine gain value, the value can be put
* into a lookup table to obtain the approximate cable length
* for each channel.
**/
/*
* Getting bits 15:9, which represent the combination of
- * course and fine gain values. The result is a number
+ * coarse and fine gain values. The result is a number
* that can be put into the lookup table to obtain the
* approximate cable length.
*/
u16 phy_data;
bool link;
- if (hw->phy.media_type != e1000_media_type_copper) {
- hw_dbg(hw, "Phy info is only valid for copper media\n");
+ if (phy->media_type != e1000_media_type_copper) {
+ e_dbg("Phy info is only valid for copper media\n");
return -E1000_ERR_CONFIG;
}
return ret_val;
if (!link) {
- hw_dbg(hw, "Phy info is only valid if link is up\n");
+ e_dbg("Phy info is only valid if link is up\n");
return -E1000_ERR_CONFIG;
}
return ret_val;
if (!link) {
- hw_dbg(hw, "Phy info is only valid if link is up\n");
+ e_dbg("Phy info is only valid if link is up\n");
return -E1000_ERR_CONFIG;
}
- phy->polarity_correction = 1;
+ phy->polarity_correction = true;
ret_val = e1000_check_polarity_igp(hw);
if (ret_val)
}
/**
+ * e1000_get_phy_info_ife - Retrieves various IFE PHY states
+ * @hw: pointer to the HW structure
+ *
+ * Populates "phy" structure with various feature states.
+ **/
+s32 e1000_get_phy_info_ife(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+ bool link;
+
+ ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link);
+ if (ret_val)
+ goto out;
+
+ if (!link) {
+ e_dbg("Phy info is only valid if link is up\n");
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ }
+
+ ret_val = e1e_rphy(hw, IFE_PHY_SPECIAL_CONTROL, &data);
+ if (ret_val)
+ goto out;
+ phy->polarity_correction = (data & IFE_PSC_AUTO_POLARITY_DISABLE)
+ ? false : true;
+
+ if (phy->polarity_correction) {
+ ret_val = e1000_check_polarity_ife(hw);
+ if (ret_val)
+ goto out;
+ } else {
+ /* Polarity is forced */
+ phy->cable_polarity = (data & IFE_PSC_FORCE_POLARITY)
+ ? e1000_rev_polarity_reversed
+ : e1000_rev_polarity_normal;
+ }
+
+ ret_val = e1e_rphy(hw, IFE_PHY_MDIX_CONTROL, &data);
+ if (ret_val)
+ goto out;
+
+ phy->is_mdix = (data & IFE_PMC_MDIX_STATUS) ? true : false;
+
+ /* The following parameters are undefined for 10/100 operation. */
+ phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED;
+ phy->local_rx = e1000_1000t_rx_status_undefined;
+ phy->remote_rx = e1000_1000t_rx_status_undefined;
+
+out:
+ return ret_val;
+}
+
+/**
* e1000e_phy_sw_reset - PHY software reset
* @hw: pointer to the HW structure
*
if (ret_val)
return 0;
- ret_val = phy->ops.acquire_phy(hw);
+ ret_val = phy->ops.acquire(hw);
if (ret_val)
return ret_val;
udelay(150);
- phy->ops.release_phy(hw);
+ phy->ops.release(hw);
return e1000_get_phy_cfg_done(hw);
}
return 0;
}
+/**
+ * e1000e_phy_init_script_igp3 - Inits the IGP3 PHY
+ * @hw: pointer to the HW structure
+ *
+ * Initializes a Intel Gigabit PHY3 when an EEPROM is not present.
+ **/
+s32 e1000e_phy_init_script_igp3(struct e1000_hw *hw)
+{
+ e_dbg("Running IGP 3 PHY init script\n");
+
+ /* PHY init IGP 3 */
+ /* Enable rise/fall, 10-mode work in class-A */
+ e1e_wphy(hw, 0x2F5B, 0x9018);
+ /* Remove all caps from Replica path filter */
+ e1e_wphy(hw, 0x2F52, 0x0000);
+ /* Bias trimming for ADC, AFE and Driver (Default) */
+ e1e_wphy(hw, 0x2FB1, 0x8B24);
+ /* Increase Hybrid poly bias */
+ e1e_wphy(hw, 0x2FB2, 0xF8F0);
+ /* Add 4% to Tx amplitude in Gig mode */
+ e1e_wphy(hw, 0x2010, 0x10B0);
+ /* Disable trimming (TTT) */
+ e1e_wphy(hw, 0x2011, 0x0000);
+ /* Poly DC correction to 94.6% + 2% for all channels */
+ e1e_wphy(hw, 0x20DD, 0x249A);
+ /* ABS DC correction to 95.9% */
+ e1e_wphy(hw, 0x20DE, 0x00D3);
+ /* BG temp curve trim */
+ e1e_wphy(hw, 0x28B4, 0x04CE);
+ /* Increasing ADC OPAMP stage 1 currents to max */
+ e1e_wphy(hw, 0x2F70, 0x29E4);
+ /* Force 1000 ( required for enabling PHY regs configuration) */
+ e1e_wphy(hw, 0x0000, 0x0140);
+ /* Set upd_freq to 6 */
+ e1e_wphy(hw, 0x1F30, 0x1606);
+ /* Disable NPDFE */
+ e1e_wphy(hw, 0x1F31, 0xB814);
+ /* Disable adaptive fixed FFE (Default) */
+ e1e_wphy(hw, 0x1F35, 0x002A);
+ /* Enable FFE hysteresis */
+ e1e_wphy(hw, 0x1F3E, 0x0067);
+ /* Fixed FFE for short cable lengths */
+ e1e_wphy(hw, 0x1F54, 0x0065);
+ /* Fixed FFE for medium cable lengths */
+ e1e_wphy(hw, 0x1F55, 0x002A);
+ /* Fixed FFE for long cable lengths */
+ e1e_wphy(hw, 0x1F56, 0x002A);
+ /* Enable Adaptive Clip Threshold */
+ e1e_wphy(hw, 0x1F72, 0x3FB0);
+ /* AHT reset limit to 1 */
+ e1e_wphy(hw, 0x1F76, 0xC0FF);
+ /* Set AHT master delay to 127 msec */
+ e1e_wphy(hw, 0x1F77, 0x1DEC);
+ /* Set scan bits for AHT */
+ e1e_wphy(hw, 0x1F78, 0xF9EF);
+ /* Set AHT Preset bits */
+ e1e_wphy(hw, 0x1F79, 0x0210);
+ /* Change integ_factor of channel A to 3 */
+ e1e_wphy(hw, 0x1895, 0x0003);
+ /* Change prop_factor of channels BCD to 8 */
+ e1e_wphy(hw, 0x1796, 0x0008);
+ /* Change cg_icount + enable integbp for channels BCD */
+ e1e_wphy(hw, 0x1798, 0xD008);
+ /*
+ * Change cg_icount + enable integbp + change prop_factor_master
+ * to 8 for channel A
+ */
+ e1e_wphy(hw, 0x1898, 0xD918);
+ /* Disable AHT in Slave mode on channel A */
+ e1e_wphy(hw, 0x187A, 0x0800);
+ /*
+ * Enable LPLU and disable AN to 1000 in non-D0a states,
+ * Enable SPD+B2B
+ */
+ e1e_wphy(hw, 0x0019, 0x008D);
+ /* Enable restart AN on an1000_dis change */
+ e1e_wphy(hw, 0x001B, 0x2080);
+ /* Enable wh_fifo read clock in 10/100 modes */
+ e1e_wphy(hw, 0x0014, 0x0045);
+ /* Restart AN, Speed selection is 1000 */
+ e1e_wphy(hw, 0x0000, 0x1340);
+
+ return 0;
+}
+
/* Internal function pointers */
/**
case IFE_C_E_PHY_ID:
phy_type = e1000_phy_ife;
break;
+ case BME1000_E_PHY_ID:
+ case BME1000_E_PHY_ID_R2:
+ phy_type = e1000_phy_bm;
+ break;
+ case I82578_E_PHY_ID:
+ phy_type = e1000_phy_82578;
+ break;
+ case I82577_E_PHY_ID:
+ phy_type = e1000_phy_82577;
+ break;
default:
phy_type = e1000_phy_unknown;
break;
}
/**
- * e1000e_commit_phy - Soft PHY reset
+ * e1000e_determine_phy_address - Determines PHY address.
* @hw: pointer to the HW structure
*
- * Performs a soft PHY reset on those that apply. This is a function pointer
- * entry point called by drivers.
+ * This uses a trial and error method to loop through possible PHY
+ * addresses. It tests each by reading the PHY ID registers and
+ * checking for a match.
**/
-s32 e1000e_commit_phy(struct e1000_hw *hw)
+s32 e1000e_determine_phy_address(struct e1000_hw *hw)
{
- if (hw->phy.ops.commit_phy)
- return hw->phy.ops.commit_phy(hw);
+ s32 ret_val = -E1000_ERR_PHY_TYPE;
+ u32 phy_addr = 0;
+ u32 i;
+ enum e1000_phy_type phy_type = e1000_phy_unknown;
- return 0;
+ hw->phy.id = phy_type;
+
+ for (phy_addr = 0; phy_addr < E1000_MAX_PHY_ADDR; phy_addr++) {
+ hw->phy.addr = phy_addr;
+ i = 0;
+
+ do {
+ e1000e_get_phy_id(hw);
+ phy_type = e1000e_get_phy_type_from_id(hw->phy.id);
+
+ /*
+ * If phy_type is valid, break - we found our
+ * PHY address
+ */
+ if (phy_type != e1000_phy_unknown) {
+ ret_val = 0;
+ goto out;
+ }
+ msleep(1);
+ i++;
+ } while (i < 10);
+ }
+
+out:
+ return ret_val;
}
/**
- * e1000_set_d0_lplu_state - Sets low power link up state for D0
+ * e1000_get_phy_addr_for_bm_page - Retrieve PHY page address
+ * @page: page to access
+ *
+ * Returns the phy address for the page requested.
+ **/
+static u32 e1000_get_phy_addr_for_bm_page(u32 page, u32 reg)
+{
+ u32 phy_addr = 2;
+
+ if ((page >= 768) || (page == 0 && reg == 25) || (reg == 31))
+ phy_addr = 1;
+
+ return phy_addr;
+}
+
+/**
+ * e1000e_write_phy_reg_bm - Write BM PHY register
* @hw: pointer to the HW structure
- * @active: boolean used to enable/disable lplu
+ * @offset: register offset to write to
+ * @data: data to write at register offset
*
- * Success returns 0, Failure returns 1
+ * Acquires semaphore, if necessary, then writes the data to PHY register
+ * at the offset. Release any acquired semaphores before exiting.
+ **/
+s32 e1000e_write_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ s32 ret_val;
+ u32 page_select = 0;
+ u32 page = offset >> IGP_PAGE_SHIFT;
+ u32 page_shift = 0;
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ return ret_val;
+
+ /* Page 800 works differently than the rest so it has its own func */
+ if (page == BM_WUC_PAGE) {
+ ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, &data,
+ false);
+ goto out;
+ }
+
+ hw->phy.addr = e1000_get_phy_addr_for_bm_page(page, offset);
+
+ if (offset > MAX_PHY_MULTI_PAGE_REG) {
+ /*
+ * Page select is register 31 for phy address 1 and 22 for
+ * phy address 2 and 3. Page select is shifted only for
+ * phy address 1.
+ */
+ if (hw->phy.addr == 1) {
+ page_shift = IGP_PAGE_SHIFT;
+ page_select = IGP01E1000_PHY_PAGE_SELECT;
+ } else {
+ page_shift = 0;
+ page_select = BM_PHY_PAGE_SELECT;
+ }
+
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000e_write_phy_reg_mdic(hw, page_select,
+ (page << page_shift));
+ if (ret_val)
+ goto out;
+ }
+
+ ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+
+out:
+ hw->phy.ops.release(hw);
+ return ret_val;
+}
+
+/**
+ * e1000e_read_phy_reg_bm - Read BM PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
*
- * The low power link up (lplu) state is set to the power management level D0
- * and SmartSpeed is disabled when active is true, else clear lplu for D0
- * and enable Smartspeed. LPLU and Smartspeed are mutually exclusive. LPLU
- * is used during Dx states where the power conservation is most important.
- * During driver activity, SmartSpeed should be enabled so performance is
- * maintained. This is a function pointer entry point called by drivers.
+ * Acquires semaphore, if necessary, then reads the PHY register at offset
+ * and storing the retrieved information in data. Release any acquired
+ * semaphores before exiting.
**/
-static s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active)
+s32 e1000e_read_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data)
{
- if (hw->phy.ops.set_d0_lplu_state)
- return hw->phy.ops.set_d0_lplu_state(hw, active);
+ s32 ret_val;
+ u32 page_select = 0;
+ u32 page = offset >> IGP_PAGE_SHIFT;
+ u32 page_shift = 0;
- return 0;
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ return ret_val;
+
+ /* Page 800 works differently than the rest so it has its own func */
+ if (page == BM_WUC_PAGE) {
+ ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, data,
+ true);
+ goto out;
+ }
+
+ hw->phy.addr = e1000_get_phy_addr_for_bm_page(page, offset);
+
+ if (offset > MAX_PHY_MULTI_PAGE_REG) {
+ /*
+ * Page select is register 31 for phy address 1 and 22 for
+ * phy address 2 and 3. Page select is shifted only for
+ * phy address 1.
+ */
+ if (hw->phy.addr == 1) {
+ page_shift = IGP_PAGE_SHIFT;
+ page_select = IGP01E1000_PHY_PAGE_SELECT;
+ } else {
+ page_shift = 0;
+ page_select = BM_PHY_PAGE_SELECT;
+ }
+
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000e_write_phy_reg_mdic(hw, page_select,
+ (page << page_shift));
+ if (ret_val)
+ goto out;
+ }
+
+ ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+out:
+ hw->phy.ops.release(hw);
+ return ret_val;
+}
+
+/**
+ * e1000e_read_phy_reg_bm2 - Read BM PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Acquires semaphore, if necessary, then reads the PHY register at offset
+ * and storing the retrieved information in data. Release any acquired
+ * semaphores before exiting.
+ **/
+s32 e1000e_read_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ s32 ret_val;
+ u16 page = (u16)(offset >> IGP_PAGE_SHIFT);
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ return ret_val;
+
+ /* Page 800 works differently than the rest so it has its own func */
+ if (page == BM_WUC_PAGE) {
+ ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, data,
+ true);
+ goto out;
+ }
+
+ hw->phy.addr = 1;
+
+ if (offset > MAX_PHY_MULTI_PAGE_REG) {
+
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_PHY_PAGE_SELECT,
+ page);
+
+ if (ret_val)
+ goto out;
+ }
+
+ ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+out:
+ hw->phy.ops.release(hw);
+ return ret_val;
+}
+
+/**
+ * e1000e_write_phy_reg_bm2 - Write BM PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Acquires semaphore, if necessary, then writes the data to PHY register
+ * at the offset. Release any acquired semaphores before exiting.
+ **/
+s32 e1000e_write_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ s32 ret_val;
+ u16 page = (u16)(offset >> IGP_PAGE_SHIFT);
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ return ret_val;
+
+ /* Page 800 works differently than the rest so it has its own func */
+ if (page == BM_WUC_PAGE) {
+ ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, &data,
+ false);
+ goto out;
+ }
+
+ hw->phy.addr = 1;
+
+ if (offset > MAX_PHY_MULTI_PAGE_REG) {
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_PHY_PAGE_SELECT,
+ page);
+
+ if (ret_val)
+ goto out;
+ }
+
+ ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+
+out:
+ hw->phy.ops.release(hw);
+ return ret_val;
+}
+
+/**
+ * e1000_access_phy_wakeup_reg_bm - Read BM PHY wakeup register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read or written
+ * @data: pointer to the data to read or write
+ * @read: determines if operation is read or write
+ *
+ * Acquires semaphore, if necessary, then reads the PHY register at offset
+ * and storing the retrieved information in data. Release any acquired
+ * semaphores before exiting. Note that procedure to read the wakeup
+ * registers are different. It works as such:
+ * 1) Set page 769, register 17, bit 2 = 1
+ * 2) Set page to 800 for host (801 if we were manageability)
+ * 3) Write the address using the address opcode (0x11)
+ * 4) Read or write the data using the data opcode (0x12)
+ * 5) Restore 769_17.2 to its original value
+ *
+ * Assumes semaphore already acquired.
+ **/
+static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
+ u16 *data, bool read)
+{
+ s32 ret_val;
+ u16 reg = BM_PHY_REG_NUM(offset);
+ u16 phy_reg = 0;
+
+ /* Gig must be disabled for MDIO accesses to page 800 */
+ if ((hw->mac.type == e1000_pchlan) &&
+ (!(er32(PHY_CTRL) & E1000_PHY_CTRL_GBE_DISABLE)))
+ e_dbg("Attempting to access page 800 while gig enabled.\n");
+
+ /* All operations in this function are phy address 1 */
+ hw->phy.addr = 1;
+
+ /* Set page 769 */
+ e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (BM_WUC_ENABLE_PAGE << IGP_PAGE_SHIFT));
+
+ ret_val = e1000e_read_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, &phy_reg);
+ if (ret_val) {
+ e_dbg("Could not read PHY page 769\n");
+ goto out;
+ }
+
+ /* First clear bit 4 to avoid a power state change */
+ phy_reg &= ~(BM_WUC_HOST_WU_BIT);
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, phy_reg);
+ if (ret_val) {
+ e_dbg("Could not clear PHY page 769 bit 4\n");
+ goto out;
+ }
+
+ /* Write bit 2 = 1, and clear bit 4 to 769_17 */
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG,
+ phy_reg | BM_WUC_ENABLE_BIT);
+ if (ret_val) {
+ e_dbg("Could not write PHY page 769 bit 2\n");
+ goto out;
+ }
+
+ /* Select page 800 */
+ ret_val = e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (BM_WUC_PAGE << IGP_PAGE_SHIFT));
+
+ /* Write the page 800 offset value using opcode 0x11 */
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ADDRESS_OPCODE, reg);
+ if (ret_val) {
+ e_dbg("Could not write address opcode to page 800\n");
+ goto out;
+ }
+
+ if (read) {
+ /* Read the page 800 value using opcode 0x12 */
+ ret_val = e1000e_read_phy_reg_mdic(hw, BM_WUC_DATA_OPCODE,
+ data);
+ } else {
+ /* Write the page 800 value using opcode 0x12 */
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_DATA_OPCODE,
+ *data);
+ }
+
+ if (ret_val) {
+ e_dbg("Could not access data value from page 800\n");
+ goto out;
+ }
+
+ /*
+ * Restore 769_17.2 to its original value
+ * Set page 769
+ */
+ e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (BM_WUC_ENABLE_PAGE << IGP_PAGE_SHIFT));
+
+ /* Clear 769_17.2 */
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, phy_reg);
+ if (ret_val) {
+ e_dbg("Could not clear PHY page 769 bit 2\n");
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000_power_up_phy_copper - Restore copper link in case of PHY power down
+ * @hw: pointer to the HW structure
+ *
+ * In the case of a PHY power down to save power, or to turn off link during a
+ * driver unload, or wake on lan is not enabled, restore the link to previous
+ * settings.
+ **/
+void e1000_power_up_phy_copper(struct e1000_hw *hw)
+{
+ u16 mii_reg = 0;
+
+ /* The PHY will retain its settings across a power down/up cycle */
+ e1e_rphy(hw, PHY_CONTROL, &mii_reg);
+ mii_reg &= ~MII_CR_POWER_DOWN;
+ e1e_wphy(hw, PHY_CONTROL, mii_reg);
+}
+
+/**
+ * e1000_power_down_phy_copper - Restore copper link in case of PHY power down
+ * @hw: pointer to the HW structure
+ *
+ * In the case of a PHY power down to save power, or to turn off link during a
+ * driver unload, or wake on lan is not enabled, restore the link to previous
+ * settings.
+ **/
+void e1000_power_down_phy_copper(struct e1000_hw *hw)
+{
+ u16 mii_reg = 0;
+
+ /* The PHY will retain its settings across a power down/up cycle */
+ e1e_rphy(hw, PHY_CONTROL, &mii_reg);
+ mii_reg |= MII_CR_POWER_DOWN;
+ e1e_wphy(hw, PHY_CONTROL, mii_reg);
+ msleep(1);
+}
+
+/**
+ * e1000e_commit_phy - Soft PHY reset
+ * @hw: pointer to the HW structure
+ *
+ * Performs a soft PHY reset on those that apply. This is a function pointer
+ * entry point called by drivers.
+ **/
+s32 e1000e_commit_phy(struct e1000_hw *hw)
+{
+ if (hw->phy.ops.commit)
+ return hw->phy.ops.commit(hw);
+
+ return 0;
+}
+
+/**
+ * e1000_set_d0_lplu_state - Sets low power link up state for D0
+ * @hw: pointer to the HW structure
+ * @active: boolean used to enable/disable lplu
+ *
+ * Success returns 0, Failure returns 1
+ *
+ * The low power link up (lplu) state is set to the power management level D0
+ * and SmartSpeed is disabled when active is true, else clear lplu for D0
+ * and enable Smartspeed. LPLU and Smartspeed are mutually exclusive. LPLU
+ * is used during Dx states where the power conservation is most important.
+ * During driver activity, SmartSpeed should be enabled so performance is
+ * maintained. This is a function pointer entry point called by drivers.
+ **/
+static s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active)
+{
+ if (hw->phy.ops.set_d0_lplu_state)
+ return hw->phy.ops.set_d0_lplu_state(hw, active);
+
+ return 0;
+}
+
+/**
+ * e1000_set_mdio_slow_mode_hv - Set slow MDIO access mode
+ * @hw: pointer to the HW structure
+ * @slow: true for slow mode, false for normal mode
+ *
+ * Assumes semaphore already acquired.
+ **/
+s32 e1000_set_mdio_slow_mode_hv(struct e1000_hw *hw, bool slow)
+{
+ s32 ret_val = 0;
+ u16 data = 0;
+
+ /* Set MDIO mode - page 769, register 16: 0x2580==slow, 0x2180==fast */
+ hw->phy.addr = 1;
+ ret_val = e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (BM_PORT_CTRL_PAGE << IGP_PAGE_SHIFT));
+ if (ret_val)
+ goto out;
+
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_CS_CTRL1,
+ (0x2180 | (slow << 10)));
+ if (ret_val)
+ goto out;
+
+ /* dummy read when reverting to fast mode - throw away result */
+ if (!slow)
+ ret_val = e1000e_read_phy_reg_mdic(hw, BM_CS_CTRL1, &data);
+
+out:
+ return ret_val;
+}
+
+/**
+ * __e1000_read_phy_reg_hv - Read HV PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ * @locked: semaphore has already been acquired or not
+ *
+ * Acquires semaphore, if necessary, then reads the PHY register at offset
+ * and stores the retrieved information in data. Release any acquired
+ * semaphore before exiting.
+ **/
+static s32 __e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data,
+ bool locked)
+{
+ s32 ret_val;
+ u16 page = BM_PHY_REG_PAGE(offset);
+ u16 reg = BM_PHY_REG_NUM(offset);
+ bool in_slow_mode = false;
+
+ if (!locked) {
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* Workaround failure in MDIO access while cable is disconnected */
+ if ((hw->phy.type == e1000_phy_82577) &&
+ !(er32(STATUS) & E1000_STATUS_LU)) {
+ ret_val = e1000_set_mdio_slow_mode_hv(hw, true);
+ if (ret_val)
+ goto out;
+
+ in_slow_mode = true;
+ }
+
+ /* Page 800 works differently than the rest so it has its own func */
+ if (page == BM_WUC_PAGE) {
+ ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset,
+ data, true);
+ goto out;
+ }
+
+ if (page > 0 && page < HV_INTC_FC_PAGE_START) {
+ ret_val = e1000_access_phy_debug_regs_hv(hw, offset,
+ data, true);
+ goto out;
+ }
+
+ hw->phy.addr = e1000_get_phy_addr_for_hv_page(page);
+
+ if (page == HV_INTC_FC_PAGE_START)
+ page = 0;
+
+ if (reg > MAX_PHY_MULTI_PAGE_REG) {
+ u32 phy_addr = hw->phy.addr;
+
+ hw->phy.addr = 1;
+
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000e_write_phy_reg_mdic(hw,
+ IGP01E1000_PHY_PAGE_SELECT,
+ (page << IGP_PAGE_SHIFT));
+ hw->phy.addr = phy_addr;
+
+ if (ret_val)
+ goto out;
+ }
+
+ ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & reg,
+ data);
+out:
+ /* Revert to MDIO fast mode, if applicable */
+ if ((hw->phy.type == e1000_phy_82577) && in_slow_mode)
+ ret_val |= e1000_set_mdio_slow_mode_hv(hw, false);
+
+ if (!locked)
+ hw->phy.ops.release(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000_read_phy_reg_hv - Read HV PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Acquires semaphore then reads the PHY register at offset and stores
+ * the retrieved information in data. Release the acquired semaphore
+ * before exiting.
+ **/
+s32 e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ return __e1000_read_phy_reg_hv(hw, offset, data, false);
+}
+
+/**
+ * e1000_read_phy_reg_hv_locked - Read HV PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Reads the PHY register at offset and stores the retrieved information
+ * in data. Assumes semaphore already acquired.
+ **/
+s32 e1000_read_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ return __e1000_read_phy_reg_hv(hw, offset, data, true);
+}
+
+/**
+ * __e1000_write_phy_reg_hv - Write HV PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ * @locked: semaphore has already been acquired or not
+ *
+ * Acquires semaphore, if necessary, then writes the data to PHY register
+ * at the offset. Release any acquired semaphores before exiting.
+ **/
+static s32 __e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data,
+ bool locked)
+{
+ s32 ret_val;
+ u16 page = BM_PHY_REG_PAGE(offset);
+ u16 reg = BM_PHY_REG_NUM(offset);
+ bool in_slow_mode = false;
+
+ if (!locked) {
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* Workaround failure in MDIO access while cable is disconnected */
+ if ((hw->phy.type == e1000_phy_82577) &&
+ !(er32(STATUS) & E1000_STATUS_LU)) {
+ ret_val = e1000_set_mdio_slow_mode_hv(hw, true);
+ if (ret_val)
+ goto out;
+
+ in_slow_mode = true;
+ }
+
+ /* Page 800 works differently than the rest so it has its own func */
+ if (page == BM_WUC_PAGE) {
+ ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset,
+ &data, false);
+ goto out;
+ }
+
+ if (page > 0 && page < HV_INTC_FC_PAGE_START) {
+ ret_val = e1000_access_phy_debug_regs_hv(hw, offset,
+ &data, false);
+ goto out;
+ }
+
+ hw->phy.addr = e1000_get_phy_addr_for_hv_page(page);
+
+ if (page == HV_INTC_FC_PAGE_START)
+ page = 0;
+
+ /*
+ * Workaround MDIO accesses being disabled after entering IEEE Power
+ * Down (whenever bit 11 of the PHY Control register is set)
+ */
+ if ((hw->phy.type == e1000_phy_82578) &&
+ (hw->phy.revision >= 1) &&
+ (hw->phy.addr == 2) &&
+ ((MAX_PHY_REG_ADDRESS & reg) == 0) &&
+ (data & (1 << 11))) {
+ u16 data2 = 0x7EFF;
+ ret_val = e1000_access_phy_debug_regs_hv(hw, (1 << 6) | 0x3,
+ &data2, false);
+ if (ret_val)
+ goto out;
+ }
+
+ if (reg > MAX_PHY_MULTI_PAGE_REG) {
+ u32 phy_addr = hw->phy.addr;
+
+ hw->phy.addr = 1;
+
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000e_write_phy_reg_mdic(hw,
+ IGP01E1000_PHY_PAGE_SELECT,
+ (page << IGP_PAGE_SHIFT));
+ hw->phy.addr = phy_addr;
+
+ if (ret_val)
+ goto out;
+ }
+
+ ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & reg,
+ data);
+
+out:
+ /* Revert to MDIO fast mode, if applicable */
+ if ((hw->phy.type == e1000_phy_82577) && in_slow_mode)
+ ret_val |= e1000_set_mdio_slow_mode_hv(hw, false);
+
+ if (!locked)
+ hw->phy.ops.release(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000_write_phy_reg_hv - Write HV PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Acquires semaphore then writes the data to PHY register at the offset.
+ * Release the acquired semaphores before exiting.
+ **/
+s32 e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ return __e1000_write_phy_reg_hv(hw, offset, data, false);
+}
+
+/**
+ * e1000_write_phy_reg_hv_locked - Write HV PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Writes the data to PHY register at the offset. Assumes semaphore
+ * already acquired.
+ **/
+s32 e1000_write_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ return __e1000_write_phy_reg_hv(hw, offset, data, true);
+}
+
+/**
+ * e1000_get_phy_addr_for_hv_page - Get PHY adrress based on page
+ * @page: page to be accessed
+ **/
+static u32 e1000_get_phy_addr_for_hv_page(u32 page)
+{
+ u32 phy_addr = 2;
+
+ if (page >= HV_INTC_FC_PAGE_START)
+ phy_addr = 1;
+
+ return phy_addr;
+}
+
+/**
+ * e1000_access_phy_debug_regs_hv - Read HV PHY vendor specific high registers
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read or written
+ * @data: pointer to the data to be read or written
+ * @read: determines if operation is read or written
+ *
+ * Reads the PHY register at offset and stores the retreived information
+ * in data. Assumes semaphore already acquired. Note that the procedure
+ * to read these regs uses the address port and data port to read/write.
+ **/
+static s32 e1000_access_phy_debug_regs_hv(struct e1000_hw *hw, u32 offset,
+ u16 *data, bool read)
+{
+ s32 ret_val;
+ u32 addr_reg = 0;
+ u32 data_reg = 0;
+
+ /* This takes care of the difference with desktop vs mobile phy */
+ addr_reg = (hw->phy.type == e1000_phy_82578) ?
+ I82578_ADDR_REG : I82577_ADDR_REG;
+ data_reg = addr_reg + 1;
+
+ /* All operations in this function are phy address 2 */
+ hw->phy.addr = 2;
+
+ /* masking with 0x3F to remove the page from offset */
+ ret_val = e1000e_write_phy_reg_mdic(hw, addr_reg, (u16)offset & 0x3F);
+ if (ret_val) {
+ e_dbg("Could not write PHY the HV address register\n");
+ goto out;
+ }
+
+ /* Read or write the data value next */
+ if (read)
+ ret_val = e1000e_read_phy_reg_mdic(hw, data_reg, data);
+ else
+ ret_val = e1000e_write_phy_reg_mdic(hw, data_reg, *data);
+
+ if (ret_val) {
+ e_dbg("Could not read data value from HV data register\n");
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000_link_stall_workaround_hv - Si workaround
+ * @hw: pointer to the HW structure
+ *
+ * This function works around a Si bug where the link partner can get
+ * a link up indication before the PHY does. If small packets are sent
+ * by the link partner they can be placed in the packet buffer without
+ * being properly accounted for by the PHY and will stall preventing
+ * further packets from being received. The workaround is to clear the
+ * packet buffer after the PHY detects link up.
+ **/
+s32 e1000_link_stall_workaround_hv(struct e1000_hw *hw)
+{
+ s32 ret_val = 0;
+ u16 data;
+
+ if (hw->phy.type != e1000_phy_82578)
+ goto out;
+
+ /* Do not apply workaround if in PHY loopback bit 14 set */
+ hw->phy.ops.read_reg(hw, PHY_CONTROL, &data);
+ if (data & PHY_CONTROL_LB)
+ goto out;
+
+ /* check if link is up and at 1Gbps */
+ ret_val = hw->phy.ops.read_reg(hw, BM_CS_STATUS, &data);
+ if (ret_val)
+ goto out;
+
+ data &= BM_CS_STATUS_LINK_UP |
+ BM_CS_STATUS_RESOLVED |
+ BM_CS_STATUS_SPEED_MASK;
+
+ if (data != (BM_CS_STATUS_LINK_UP |
+ BM_CS_STATUS_RESOLVED |
+ BM_CS_STATUS_SPEED_1000))
+ goto out;
+
+ mdelay(200);
+
+ /* flush the packets in the fifo buffer */
+ ret_val = hw->phy.ops.write_reg(hw, HV_MUX_DATA_CTRL,
+ HV_MUX_DATA_CTRL_GEN_TO_MAC |
+ HV_MUX_DATA_CTRL_FORCE_SPEED);
+ if (ret_val)
+ goto out;
+
+ ret_val = hw->phy.ops.write_reg(hw, HV_MUX_DATA_CTRL,
+ HV_MUX_DATA_CTRL_GEN_TO_MAC);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000_check_polarity_82577 - Checks the polarity.
+ * @hw: pointer to the HW structure
+ *
+ * Success returns 0, Failure returns -E1000_ERR_PHY (-2)
+ *
+ * Polarity is determined based on the PHY specific status register.
+ **/
+s32 e1000_check_polarity_82577(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+
+ ret_val = phy->ops.read_reg(hw, I82577_PHY_STATUS_2, &data);
+
+ if (!ret_val)
+ phy->cable_polarity = (data & I82577_PHY_STATUS2_REV_POLARITY)
+ ? e1000_rev_polarity_reversed
+ : e1000_rev_polarity_normal;
+
+ return ret_val;
+}
+
+/**
+ * e1000_phy_force_speed_duplex_82577 - Force speed/duplex for I82577 PHY
+ * @hw: pointer to the HW structure
+ *
+ * Calls the PHY setup function to force speed and duplex. Clears the
+ * auto-crossover to force MDI manually. Waits for link and returns
+ * successful if link up is successful, else -E1000_ERR_PHY (-2).
+ **/
+s32 e1000_phy_force_speed_duplex_82577(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data;
+ bool link;
+
+ ret_val = phy->ops.read_reg(hw, PHY_CONTROL, &phy_data);
+ if (ret_val)
+ goto out;
+
+ e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
+
+ ret_val = phy->ops.write_reg(hw, PHY_CONTROL, phy_data);
+ if (ret_val)
+ goto out;
+
+ /*
+ * Clear Auto-Crossover to force MDI manually. 82577 requires MDI
+ * forced whenever speed and duplex are forced.
+ */
+ ret_val = phy->ops.read_reg(hw, I82577_PHY_CTRL_2, &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy_data &= ~I82577_PHY_CTRL2_AUTO_MDIX;
+ phy_data &= ~I82577_PHY_CTRL2_FORCE_MDI_MDIX;
+
+ ret_val = phy->ops.write_reg(hw, I82577_PHY_CTRL_2, phy_data);
+ if (ret_val)
+ goto out;
+
+ e_dbg("I82577_PHY_CTRL_2: %X\n", phy_data);
+
+ udelay(1);
+
+ if (phy->autoneg_wait_to_complete) {
+ e_dbg("Waiting for forced speed/duplex link on 82577 phy\n");
+
+ ret_val = e1000e_phy_has_link_generic(hw,
+ PHY_FORCE_LIMIT,
+ 100000,
+ &link);
+ if (ret_val)
+ goto out;
+
+ if (!link)
+ e_dbg("Link taking longer than expected.\n");
+
+ /* Try once more */
+ ret_val = e1000e_phy_has_link_generic(hw,
+ PHY_FORCE_LIMIT,
+ 100000,
+ &link);
+ if (ret_val)
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000_get_phy_info_82577 - Retrieve I82577 PHY information
+ * @hw: pointer to the HW structure
+ *
+ * Read PHY status to determine if link is up. If link is up, then
+ * set/determine 10base-T extended distance and polarity correction. Read
+ * PHY port status to determine MDI/MDIx and speed. Based on the speed,
+ * determine on the cable length, local and remote receiver.
+ **/
+s32 e1000_get_phy_info_82577(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+ bool link;
+
+ ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link);
+ if (ret_val)
+ goto out;
+
+ if (!link) {
+ e_dbg("Phy info is only valid if link is up\n");
+ ret_val = -E1000_ERR_CONFIG;
+ goto out;
+ }
+
+ phy->polarity_correction = true;
+
+ ret_val = e1000_check_polarity_82577(hw);
+ if (ret_val)
+ goto out;
+
+ ret_val = phy->ops.read_reg(hw, I82577_PHY_STATUS_2, &data);
+ if (ret_val)
+ goto out;
+
+ phy->is_mdix = (data & I82577_PHY_STATUS2_MDIX) ? true : false;
+
+ if ((data & I82577_PHY_STATUS2_SPEED_MASK) ==
+ I82577_PHY_STATUS2_SPEED_1000MBPS) {
+ ret_val = hw->phy.ops.get_cable_length(hw);
+ if (ret_val)
+ goto out;
+
+ ret_val = phy->ops.read_reg(hw, PHY_1000T_STATUS, &data);
+ if (ret_val)
+ goto out;
+
+ phy->local_rx = (data & SR_1000T_LOCAL_RX_STATUS)
+ ? e1000_1000t_rx_status_ok
+ : e1000_1000t_rx_status_not_ok;
+
+ phy->remote_rx = (data & SR_1000T_REMOTE_RX_STATUS)
+ ? e1000_1000t_rx_status_ok
+ : e1000_1000t_rx_status_not_ok;
+ } else {
+ phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED;
+ phy->local_rx = e1000_1000t_rx_status_undefined;
+ phy->remote_rx = e1000_1000t_rx_status_undefined;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000_get_cable_length_82577 - Determine cable length for 82577 PHY
+ * @hw: pointer to the HW structure
+ *
+ * Reads the diagnostic status register and verifies result is valid before
+ * placing it in the phy_cable_length field.
+ **/
+s32 e1000_get_cable_length_82577(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data, length;
+
+ ret_val = phy->ops.read_reg(hw, I82577_PHY_DIAG_STATUS, &phy_data);
+ if (ret_val)
+ goto out;
+
+ length = (phy_data & I82577_DSTATUS_CABLE_LENGTH) >>
+ I82577_DSTATUS_CABLE_LENGTH_SHIFT;
+
+ if (length == E1000_CABLE_LENGTH_UNDEFINED)
+ ret_val = -E1000_ERR_PHY;
+
+ phy->cable_length = length;
+
+out:
+ return ret_val;
}
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff