}
}
+static bool e1000_has_link(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ bool link_active = false;
+
+ /* get_link_status is set on LSC (link status) interrupt or
+ * rx sequence error interrupt. get_link_status will stay
+ * false until the e1000_check_for_link establishes link
+ * for copper adapters ONLY
+ */
+ switch (hw->media_type) {
+ case e1000_media_type_copper:
+ if (hw->get_link_status) {
+ e1000_check_for_link(hw);
+ link_active = !hw->get_link_status;
+ } else {
+ link_active = true;
+ }
+ break;
+ case e1000_media_type_fiber:
+ e1000_check_for_link(hw);
+ link_active = !!(er32(STATUS) & E1000_STATUS_LU);
+ break;
+ case e1000_media_type_internal_serdes:
+ e1000_check_for_link(hw);
+ link_active = hw->serdes_has_link;
+ break;
+ default:
+ break;
+ }
+
+ return link_active;
+}
+
/**
* e1000_watchdog - Timer Call-back
* @data: pointer to adapter cast into an unsigned long
struct e1000_tx_ring *txdr = adapter->tx_ring;
u32 link, tctl;
- e1000_check_for_link(hw);
-
- if ((hw->media_type == e1000_media_type_internal_serdes) &&
- !(er32(TXCW) & E1000_TXCW_ANE))
- link = !hw->serdes_link_down;
- else
- link = er32(STATUS) & E1000_STATUS_LU;
+ link = e1000_has_link(adapter);
+ if ((netif_carrier_ok(netdev)) && link)
+ goto link_up;
if (link) {
if (!netif_carrier_ok(netdev)) {
u32 ctrl;
bool txb2b = true;
+ /* update snapshot of PHY registers on LSC */
e1000_get_speed_and_duplex(hw,
&adapter->link_speed,
&adapter->link_duplex);
case SPEED_10:
txb2b = false;
netdev->tx_queue_len = 10;
- adapter->tx_timeout_factor = 8;
+ adapter->tx_timeout_factor = 16;
break;
case SPEED_100:
txb2b = false;
e1000_smartspeed(adapter);
}
+link_up:
e1000_update_stats(adapter);
hw->tx_packet_delta = adapter->stats.tpt - adapter->tpt_old;
/**
* e1000_update_itr - update the dynamic ITR value based on statistics
+ * @adapter: pointer to adapter
+ * @itr_setting: current adapter->itr
+ * @packets: the number of packets during this measurement interval
+ * @bytes: the number of bytes during this measurement interval
+ *
* Stores a new ITR value based on packets and byte
* counts during the last interrupt. The advantage of per interrupt
* computation is faster updates and more accurate ITR for the current
* while increasing bulk throughput.
* this functionality is controlled by the InterruptThrottleRate module
* parameter (see e1000_param.c)
- * @adapter: pointer to adapter
- * @itr_setting: current adapter->itr
- * @packets: the number of packets during this measurement interval
- * @bytes: the number of bytes during this measurement interval
**/
static unsigned int e1000_update_itr(struct e1000_adapter *adapter,
u16 itr_setting, int packets, int bytes)
size -= 4;
buffer_info->length = size;
- buffer_info->dma = skb_shinfo(skb)->dma_head + offset;
+ /* set time_stamp *before* dma to help avoid a possible race */
buffer_info->time_stamp = jiffies;
+ buffer_info->dma = skb_shinfo(skb)->dma_head + offset;
buffer_info->next_to_watch = i;
len -= size;
* Avoid terminating buffers within evenly-aligned
* dwords. */
if (unlikely(adapter->pcix_82544 &&
- !((unsigned long)(frag->page+offset+size-1) & 4) &&
- size > 4))
+ !((unsigned long)(page_to_phys(frag->page) + offset
+ + size - 1) & 4) &&
+ size > 4))
size -= 4;
buffer_info->length = size;
- buffer_info->dma = map[f] + offset;
buffer_info->time_stamp = jiffies;
+ buffer_info->dma = map[f] + offset;
buffer_info->next_to_watch = i;
len -= size;
}
if (likely(tso)) {
- tx_ring->last_tx_tso = 1;
+ if (likely(hw->mac_type != e1000_82544))
+ tx_ring->last_tx_tso = 1;
tx_flags |= E1000_TX_FLAGS_TSO;
} else if (likely(e1000_tx_csum(adapter, tx_ring, skb)))
tx_flags |= E1000_TX_FLAGS_CSUM;
break;
}
+ while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
+ msleep(1);
+ /* e1000_down has a dependency on max_frame_size */
+ hw->max_frame_size = max_frame;
+ if (netif_running(netdev))
+ e1000_down(adapter);
+
/* NOTE: netdev_alloc_skb reserves 16 bytes, and typically NET_IP_ALIGN
* means we reserve 2 more, this pushes us to allocate from the next
* larger slab size.
(max_frame == MAXIMUM_ETHERNET_VLAN_SIZE)))
adapter->rx_buffer_len = MAXIMUM_ETHERNET_VLAN_SIZE;
+ printk(KERN_INFO "e1000: %s changing MTU from %d to %d\n",
+ netdev->name, netdev->mtu, new_mtu);
netdev->mtu = new_mtu;
- hw->max_frame_size = max_frame;
if (netif_running(netdev))
- e1000_reinit_locked(adapter);
+ e1000_up(adapter);
+ else
+ e1000_reset(adapter);
+
+ clear_bit(__E1000_RESETTING, &adapter->flags);
return 0;
}
static int e1000_clean(struct napi_struct *napi, int budget)
{
struct e1000_adapter *adapter = container_of(napi, struct e1000_adapter, napi);
- struct net_device *poll_dev = adapter->netdev;
- int tx_cleaned = 0, work_done = 0;
-
- adapter = netdev_priv(poll_dev);
+ int tx_clean_complete = 0, work_done = 0;
- tx_cleaned = e1000_clean_tx_irq(adapter, &adapter->tx_ring[0]);
+ tx_clean_complete = e1000_clean_tx_irq(adapter, &adapter->tx_ring[0]);
- adapter->clean_rx(adapter, &adapter->rx_ring[0],
- &work_done, budget);
+ adapter->clean_rx(adapter, &adapter->rx_ring[0], &work_done, budget);
- if (!tx_cleaned)
+ if (!tx_clean_complete)
work_done = budget;
/* If budget not fully consumed, exit the polling mode */
* sees the new next_to_clean.
*/
smp_mb();
- if (netif_queue_stopped(netdev)) {
+
+ if (netif_queue_stopped(netdev) &&
+ !(test_bit(__E1000_DOWN, &adapter->flags))) {
netif_wake_queue(netdev);
++adapter->restart_queue;
}
/* Detect a transmit hang in hardware, this serializes the
* check with the clearing of time_stamp and movement of i */
adapter->detect_tx_hung = false;
- if (tx_ring->buffer_info[i].time_stamp &&
- time_after(jiffies, tx_ring->buffer_info[i].time_stamp +
+ if (tx_ring->buffer_info[eop].time_stamp &&
+ time_after(jiffies, tx_ring->buffer_info[eop].time_stamp +
(adapter->tx_timeout_factor * HZ))
&& !(er32(STATUS) & E1000_STATUS_TXOFF)) {
readl(hw->hw_addr + tx_ring->tdt),
tx_ring->next_to_use,
tx_ring->next_to_clean,
- tx_ring->buffer_info[i].time_stamp,
+ tx_ring->buffer_info[eop].time_stamp,
eop,
jiffies,
eop_desc->upper.fields.status);
pcix_set_mmrbc(adapter->pdev, mmrbc);
}
-s32 e1000_read_pcie_cap_reg(struct e1000_hw *hw, u32 reg, u16 *value)
-{
- struct e1000_adapter *adapter = hw->back;
- u16 cap_offset;
-
- cap_offset = pci_find_capability(adapter->pdev, PCI_CAP_ID_EXP);
- if (!cap_offset)
- return -E1000_ERR_CONFIG;
-
- pci_read_config_word(adapter->pdev, cap_offset + reg, value);
-
- return E1000_SUCCESS;
-}
-
void e1000_io_write(struct e1000_hw *hw, unsigned long port, u32 value)
{
outl(value, port);
ew32(RCTL, rctl);
if (adapter->mng_vlan_id != (u16)E1000_MNG_VLAN_NONE) {
- e1000_vlan_rx_kill_vid(netdev,
- adapter->mng_vlan_id);
+ e1000_vlan_rx_kill_vid(netdev, adapter->mng_vlan_id);
adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
}
}
/**
* e1000_io_error_detected - called when PCI error is detected
* @pdev: Pointer to PCI device
- * @state: The current pci conneection state
+ * @state: The current pci connection state
*
* This function is called after a PCI bus error affecting
* this device has been detected.