static void mi1_init(struct adapter *adap, const struct adapter_info *ai)
{
u32 clkdiv = adap->params.vpd.cclk / (2 * adap->params.vpd.mdc) - 1;
- u32 val = F_PREEN | V_MDIINV(ai->mdiinv) | V_MDIEN(ai->mdien) |
- V_CLKDIV(clkdiv);
+ u32 val = F_PREEN | V_CLKDIV(clkdiv);
- if (!(ai->caps & SUPPORTED_10000baseT_Full))
- val |= V_ST(1);
t3_write_reg(adap, A_MI1_CFG, val);
}
-#define MDIO_ATTEMPTS 10
+#define MDIO_ATTEMPTS 20
/*
- * MI1 read/write operations for direct-addressed PHYs.
+ * MI1 read/write operations for clause 22 PHYs.
*/
-static int mi1_read(struct adapter *adapter, int phy_addr, int mmd_addr,
- int reg_addr, unsigned int *valp)
+static int t3_mi1_read(struct adapter *adapter, int phy_addr, int mmd_addr,
+ int reg_addr, unsigned int *valp)
{
int ret;
u32 addr = V_REGADDR(reg_addr) | V_PHYADDR(phy_addr);
return -EINVAL;
mutex_lock(&adapter->mdio_lock);
+ t3_set_reg_field(adapter, A_MI1_CFG, V_ST(M_ST), V_ST(1));
t3_write_reg(adapter, A_MI1_ADDR, addr);
t3_write_reg(adapter, A_MI1_OP, V_MDI_OP(2));
- ret = t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0, MDIO_ATTEMPTS, 20);
+ ret = t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0, MDIO_ATTEMPTS, 10);
if (!ret)
*valp = t3_read_reg(adapter, A_MI1_DATA);
mutex_unlock(&adapter->mdio_lock);
return ret;
}
-static int mi1_write(struct adapter *adapter, int phy_addr, int mmd_addr,
+static int t3_mi1_write(struct adapter *adapter, int phy_addr, int mmd_addr,
int reg_addr, unsigned int val)
{
int ret;
return -EINVAL;
mutex_lock(&adapter->mdio_lock);
+ t3_set_reg_field(adapter, A_MI1_CFG, V_ST(M_ST), V_ST(1));
t3_write_reg(adapter, A_MI1_ADDR, addr);
t3_write_reg(adapter, A_MI1_DATA, val);
t3_write_reg(adapter, A_MI1_OP, V_MDI_OP(1));
- ret = t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0, MDIO_ATTEMPTS, 20);
+ ret = t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0, MDIO_ATTEMPTS, 10);
mutex_unlock(&adapter->mdio_lock);
return ret;
}
static const struct mdio_ops mi1_mdio_ops = {
- mi1_read,
- mi1_write
+ t3_mi1_read,
+ t3_mi1_write
};
/*
+ * Performs the address cycle for clause 45 PHYs.
+ * Must be called with the MDIO_LOCK held.
+ */
+static int mi1_wr_addr(struct adapter *adapter, int phy_addr, int mmd_addr,
+ int reg_addr)
+{
+ u32 addr = V_REGADDR(mmd_addr) | V_PHYADDR(phy_addr);
+
+ t3_set_reg_field(adapter, A_MI1_CFG, V_ST(M_ST), 0);
+ t3_write_reg(adapter, A_MI1_ADDR, addr);
+ t3_write_reg(adapter, A_MI1_DATA, reg_addr);
+ t3_write_reg(adapter, A_MI1_OP, V_MDI_OP(0));
+ return t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0,
+ MDIO_ATTEMPTS, 10);
+}
+
+/*
* MI1 read/write operations for indirect-addressed PHYs.
*/
static int mi1_ext_read(struct adapter *adapter, int phy_addr, int mmd_addr,
int reg_addr, unsigned int *valp)
{
int ret;
- u32 addr = V_REGADDR(mmd_addr) | V_PHYADDR(phy_addr);
mutex_lock(&adapter->mdio_lock);
- t3_write_reg(adapter, A_MI1_ADDR, addr);
- t3_write_reg(adapter, A_MI1_DATA, reg_addr);
- t3_write_reg(adapter, A_MI1_OP, V_MDI_OP(0));
- ret = t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0, MDIO_ATTEMPTS, 20);
+ ret = mi1_wr_addr(adapter, phy_addr, mmd_addr, reg_addr);
if (!ret) {
t3_write_reg(adapter, A_MI1_OP, V_MDI_OP(3));
ret = t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0,
- MDIO_ATTEMPTS, 20);
+ MDIO_ATTEMPTS, 10);
if (!ret)
*valp = t3_read_reg(adapter, A_MI1_DATA);
}
int reg_addr, unsigned int val)
{
int ret;
- u32 addr = V_REGADDR(mmd_addr) | V_PHYADDR(phy_addr);
mutex_lock(&adapter->mdio_lock);
- t3_write_reg(adapter, A_MI1_ADDR, addr);
- t3_write_reg(adapter, A_MI1_DATA, reg_addr);
- t3_write_reg(adapter, A_MI1_OP, V_MDI_OP(0));
- ret = t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0, MDIO_ATTEMPTS, 20);
+ ret = mi1_wr_addr(adapter, phy_addr, mmd_addr, reg_addr);
if (!ret) {
t3_write_reg(adapter, A_MI1_DATA, val);
t3_write_reg(adapter, A_MI1_OP, V_MDI_OP(1));
ret = t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0,
- MDIO_ATTEMPTS, 20);
+ MDIO_ATTEMPTS, 10);
}
mutex_unlock(&adapter->mdio_lock);
return ret;
return mdio_write(phy, 0, MII_BMCR, ctl);
}
+int t3_phy_lasi_intr_enable(struct cphy *phy)
+{
+ return mdio_write(phy, MDIO_DEV_PMA_PMD, LASI_CTRL, 1);
+}
+
+int t3_phy_lasi_intr_disable(struct cphy *phy)
+{
+ return mdio_write(phy, MDIO_DEV_PMA_PMD, LASI_CTRL, 0);
+}
+
+int t3_phy_lasi_intr_clear(struct cphy *phy)
+{
+ u32 val;
+
+ return mdio_read(phy, MDIO_DEV_PMA_PMD, LASI_STAT, &val);
+}
+
+int t3_phy_lasi_intr_handler(struct cphy *phy)
+{
+ unsigned int status;
+ int err = mdio_read(phy, MDIO_DEV_PMA_PMD, LASI_STAT, &status);
+
+ if (err)
+ return err;
+ return (status & 1) ? cphy_cause_link_change : 0;
+}
+
static const struct adapter_info t3_adap_info[] = {
- {2, 0, 0, 0,
+ {2, 0,
F_GPIO2_OEN | F_GPIO4_OEN |
- F_GPIO2_OUT_VAL | F_GPIO4_OUT_VAL, F_GPIO3 | F_GPIO5,
- 0,
+ F_GPIO2_OUT_VAL | F_GPIO4_OUT_VAL, { S_GPIO3, S_GPIO5 }, 0,
&mi1_mdio_ops, "Chelsio PE9000"},
- {2, 0, 0, 0,
+ {2, 0,
F_GPIO2_OEN | F_GPIO4_OEN |
- F_GPIO2_OUT_VAL | F_GPIO4_OUT_VAL, F_GPIO3 | F_GPIO5,
- 0,
+ F_GPIO2_OUT_VAL | F_GPIO4_OUT_VAL, { S_GPIO3, S_GPIO5 }, 0,
&mi1_mdio_ops, "Chelsio T302"},
- {1, 0, 0, 0,
+ {1, 0,
F_GPIO1_OEN | F_GPIO6_OEN | F_GPIO7_OEN | F_GPIO10_OEN |
F_GPIO11_OEN | F_GPIO1_OUT_VAL | F_GPIO6_OUT_VAL | F_GPIO10_OUT_VAL,
- 0, SUPPORTED_10000baseT_Full | SUPPORTED_AUI,
+ { 0 }, SUPPORTED_10000baseT_Full | SUPPORTED_AUI,
&mi1_mdio_ext_ops, "Chelsio T310"},
- {2, 0, 0, 0,
+ {2, 0,
F_GPIO1_OEN | F_GPIO2_OEN | F_GPIO4_OEN | F_GPIO5_OEN | F_GPIO6_OEN |
F_GPIO7_OEN | F_GPIO10_OEN | F_GPIO11_OEN | F_GPIO1_OUT_VAL |
- F_GPIO5_OUT_VAL | F_GPIO6_OUT_VAL | F_GPIO10_OUT_VAL, 0,
- SUPPORTED_10000baseT_Full | SUPPORTED_AUI,
+ F_GPIO5_OUT_VAL | F_GPIO6_OUT_VAL | F_GPIO10_OUT_VAL,
+ { S_GPIO9, S_GPIO3 }, SUPPORTED_10000baseT_Full | SUPPORTED_AUI,
&mi1_mdio_ext_ops, "Chelsio T320"},
};
return id < ARRAY_SIZE(t3_adap_info) ? &t3_adap_info[id] : NULL;
}
-#define CAPS_1G (SUPPORTED_10baseT_Full | SUPPORTED_100baseT_Full | \
- SUPPORTED_1000baseT_Full | SUPPORTED_Autoneg | SUPPORTED_MII)
-#define CAPS_10G (SUPPORTED_10000baseT_Full | SUPPORTED_AUI)
+struct port_type_info {
+ int (*phy_prep)(struct cphy *phy, struct adapter *adapter,
+ int phy_addr, const struct mdio_ops *ops);
+};
static const struct port_type_info port_types[] = {
- {NULL},
- {t3_ael1002_phy_prep, CAPS_10G | SUPPORTED_FIBRE,
- "10GBASE-XR"},
- {t3_vsc8211_phy_prep, CAPS_1G | SUPPORTED_TP | SUPPORTED_IRQ,
- "10/100/1000BASE-T"},
- {NULL, CAPS_1G | SUPPORTED_TP | SUPPORTED_IRQ,
- "10/100/1000BASE-T"},
- {t3_xaui_direct_phy_prep, CAPS_10G | SUPPORTED_TP, "10GBASE-CX4"},
- {NULL, CAPS_10G, "10GBASE-KX4"},
- {t3_qt2045_phy_prep, CAPS_10G | SUPPORTED_TP, "10GBASE-CX4"},
- {t3_ael1006_phy_prep, CAPS_10G | SUPPORTED_FIBRE,
- "10GBASE-SR"},
- {NULL, CAPS_10G | SUPPORTED_TP, "10GBASE-CX4"},
+ { NULL },
+ { t3_ael1002_phy_prep },
+ { t3_vsc8211_phy_prep },
+ { NULL},
+ { t3_xaui_direct_phy_prep },
+ { NULL },
+ { t3_qt2045_phy_prep },
+ { t3_ael1006_phy_prep },
+ { NULL },
};
-#undef CAPS_1G
-#undef CAPS_10G
-
#define VPD_ENTRY(name, len) \
u8 name##_kword[2]; u8 name##_len; u8 name##_data[len]
* addres is written to the control register. The hardware device will
* set the flag to 1 when 4 bytes have been read into the data register.
*/
-int t3_seeprom_read(struct adapter *adapter, u32 addr, u32 *data)
+int t3_seeprom_read(struct adapter *adapter, u32 addr, __le32 *data)
{
u16 val;
int attempts = EEPROM_MAX_POLL;
+ u32 v;
unsigned int base = adapter->params.pci.vpd_cap_addr;
if ((addr >= EEPROMSIZE && addr != EEPROM_STAT_ADDR) || (addr & 3))
CH_ERR(adapter, "reading EEPROM address 0x%x failed\n", addr);
return -EIO;
}
- pci_read_config_dword(adapter->pdev, base + PCI_VPD_DATA, data);
- *data = le32_to_cpu(*data);
+ pci_read_config_dword(adapter->pdev, base + PCI_VPD_DATA, &v);
+ *data = cpu_to_le32(v);
return 0;
}
* Write a 32-bit word to a location in VPD EEPROM using the card's PCI
* VPD ROM capability.
*/
-int t3_seeprom_write(struct adapter *adapter, u32 addr, u32 data)
+int t3_seeprom_write(struct adapter *adapter, u32 addr, __le32 data)
{
u16 val;
int attempts = EEPROM_MAX_POLL;
return -EINVAL;
pci_write_config_dword(adapter->pdev, base + PCI_VPD_DATA,
- cpu_to_le32(data));
+ le32_to_cpu(data));
pci_write_config_word(adapter->pdev,base + PCI_VPD_ADDR,
addr | PCI_VPD_ADDR_F);
do {
* Card information is normally at VPD_BASE but some early cards had
* it at 0.
*/
- ret = t3_seeprom_read(adapter, VPD_BASE, (u32 *)&vpd);
+ ret = t3_seeprom_read(adapter, VPD_BASE, (__le32 *)&vpd);
if (ret)
return ret;
addr = vpd.id_tag == 0x82 ? VPD_BASE : 0;
for (i = 0; i < sizeof(vpd); i += 4) {
ret = t3_seeprom_read(adapter, addr + i,
- (u32 *)((u8 *)&vpd + i));
+ (__le32 *)((u8 *)&vpd + i));
if (ret)
return ret;
}
SF_ERASE_SECTOR = 0xd8, /* erase sector */
FW_FLASH_BOOT_ADDR = 0x70000, /* start address of FW in flash */
- FW_VERS_ADDR = 0x77ffc, /* flash address holding FW version */
+ FW_VERS_ADDR = 0x7fffc, /* flash address holding FW version */
FW_MIN_SIZE = 8 /* at least version and csum */
};
* Checks if an adapter's tp sram is compatible with the driver.
* Returns 0 if the versions are compatible, a negative error otherwise.
*/
-int t3_check_tpsram(struct adapter *adapter, u8 *tp_sram, unsigned int size)
+int t3_check_tpsram(struct adapter *adapter, const u8 *tp_sram,
+ unsigned int size)
{
u32 csum;
unsigned int i;
- const u32 *p = (const u32 *)tp_sram;
+ const __be32 *p = (const __be32 *)tp_sram;
/* Verify checksum */
for (csum = 0, i = 0; i < size / sizeof(csum); i++)
{
u32 csum;
unsigned int i;
- const u32 *p = (const u32 *)fw_data;
+ const __be32 *p = (const __be32 *)fw_data;
int ret, addr, fw_sector = FW_FLASH_BOOT_ADDR >> 16;
if ((size & 3) || size < FW_MIN_SIZE)
phy->ops->get_link_status(phy, &link_ok, &speed, &duplex, &fc);
+ if (lc->requested_fc & PAUSE_AUTONEG)
+ fc &= lc->requested_fc;
+ else
+ fc = lc->requested_fc & (PAUSE_RX | PAUSE_TX);
+
+ if (link_ok == lc->link_ok && speed == lc->speed &&
+ duplex == lc->duplex && fc == lc->fc)
+ return; /* nothing changed */
+
if (link_ok != lc->link_ok && adapter->params.rev > 0 &&
uses_xaui(adapter)) {
if (link_ok)
lc->link_ok = link_ok;
lc->speed = speed < 0 ? SPEED_INVALID : speed;
lc->duplex = duplex < 0 ? DUPLEX_INVALID : duplex;
- if (lc->requested_fc & PAUSE_AUTONEG)
- fc &= lc->requested_fc;
- else
- fc = lc->requested_fc & (PAUSE_RX | PAUSE_TX);
if (link_ok && speed >= 0 && lc->autoneg == AUTONEG_ENABLE) {
/* Set MAC speed, duplex, and flow control to match PHY. */
fc);
/* Also disables autoneg */
phy->ops->set_speed_duplex(phy, lc->speed, lc->duplex);
- phy->ops->reset(phy, 0);
} else
phy->ops->autoneg_enable(phy);
} else {
unsigned int mask; /* bits to check in interrupt status */
const char *msg; /* message to print or NULL */
short stat_idx; /* stat counter to increment or -1 */
- unsigned short fatal:1; /* whether the condition reported is fatal */
+ unsigned short fatal; /* whether the condition reported is fatal */
};
/**
*/
int t3_phy_intr_handler(struct adapter *adapter)
{
- u32 mask, gpi = adapter_info(adapter)->gpio_intr;
u32 i, cause = t3_read_reg(adapter, A_T3DBG_INT_CAUSE);
for_each_port(adapter, i) {
struct port_info *p = adap2pinfo(adapter, i);
- mask = gpi - (gpi & (gpi - 1));
- gpi -= mask;
-
- if (!(p->port_type->caps & SUPPORTED_IRQ))
+ if (!(p->phy.caps & SUPPORTED_IRQ))
continue;
- if (cause & mask) {
+ if (cause & (1 << adapter_info(adapter)->gpio_intr[i])) {
int phy_cause = p->phy.ops->intr_handler(&p->phy);
if (phy_cause & cphy_cause_link_change)
return 1;
}
+static unsigned int calc_gpio_intr(struct adapter *adap)
+{
+ unsigned int i, gpi_intr = 0;
+
+ for_each_port(adap, i)
+ if ((adap2pinfo(adap, i)->phy.caps & SUPPORTED_IRQ) &&
+ adapter_info(adap)->gpio_intr[i])
+ gpi_intr |= 1 << adapter_info(adap)->gpio_intr[i];
+ return gpi_intr;
+}
+
/**
* t3_intr_enable - enable interrupts
* @adapter: the adapter whose interrupts should be enabled
t3_write_reg(adapter, A_ULPTX_INT_ENABLE, ULPTX_INTR_MASK);
}
- t3_write_reg(adapter, A_T3DBG_GPIO_ACT_LOW,
- adapter_info(adapter)->gpio_intr);
- t3_write_reg(adapter, A_T3DBG_INT_ENABLE,
- adapter_info(adapter)->gpio_intr);
+ t3_write_reg(adapter, A_T3DBG_INT_ENABLE, calc_gpio_intr(adapter));
+
if (is_pcie(adapter))
t3_write_reg(adapter, A_PCIE_INT_ENABLE, PCIE_INTR_MASK);
else
V_PMMAXXFERLEN0(size) | V_PMMAXXFERLEN1(size));
}
-static void __devinit init_mtus(unsigned short mtus[])
+static void init_mtus(unsigned short mtus[])
{
/*
* See draft-mathis-plpmtud-00.txt for the values. The min is 88 so
/*
* Initial congestion control parameters.
*/
-static void __devinit init_cong_ctrl(unsigned short *a, unsigned short *b)
+static void init_cong_ctrl(unsigned short *a, unsigned short *b)
{
a[0] = a[1] = a[2] = a[3] = a[4] = a[5] = a[6] = a[7] = a[8] = 1;
a[9] = 2;
*
* Write the contents of the protocol SRAM.
*/
-int t3_set_proto_sram(struct adapter *adap, u8 *data)
+int t3_set_proto_sram(struct adapter *adap, const u8 *data)
{
int i;
- u32 *buf = (u32 *)data;
+ const __be32 *buf = (const __be32 *)data;
for (i = 0; i < PROTO_SRAM_LINES; i++) {
- t3_write_reg(adap, A_TP_EMBED_OP_FIELD5, cpu_to_be32(*buf++));
- t3_write_reg(adap, A_TP_EMBED_OP_FIELD4, cpu_to_be32(*buf++));
- t3_write_reg(adap, A_TP_EMBED_OP_FIELD3, cpu_to_be32(*buf++));
- t3_write_reg(adap, A_TP_EMBED_OP_FIELD2, cpu_to_be32(*buf++));
- t3_write_reg(adap, A_TP_EMBED_OP_FIELD1, cpu_to_be32(*buf++));
+ t3_write_reg(adap, A_TP_EMBED_OP_FIELD5, be32_to_cpu(*buf++));
+ t3_write_reg(adap, A_TP_EMBED_OP_FIELD4, be32_to_cpu(*buf++));
+ t3_write_reg(adap, A_TP_EMBED_OP_FIELD3, be32_to_cpu(*buf++));
+ t3_write_reg(adap, A_TP_EMBED_OP_FIELD2, be32_to_cpu(*buf++));
+ t3_write_reg(adap, A_TP_EMBED_OP_FIELD1, be32_to_cpu(*buf++));
t3_write_reg(adap, A_TP_EMBED_OP_FIELD0, i << 1 | 1 << 31);
if (t3_wait_op_done(adap, A_TP_EMBED_OP_FIELD0, 1, 1, 5, 1))
t3_write_reg(adap, A_PCIE_PEX_ERR, 0xffffffff);
t3_set_reg_field(adap, A_PCIE_CFG, 0,
+ F_ENABLELINKDWNDRST | F_ENABLELINKDOWNRST |
F_PCIE_DMASTOPEN | F_PCIE_CLIDECEN);
}
init_hw_for_avail_ports(adapter, adapter->params.nports);
t3_sge_init(adapter, &adapter->params.sge);
+ t3_write_reg(adapter, A_T3DBG_GPIO_ACT_LOW, calc_gpio_intr(adapter));
+
t3_write_reg(adapter, A_CIM_HOST_ACC_DATA, vpd->uclk | fw_params);
t3_write_reg(adapter, A_CIM_BOOT_CFG,
V_BOOTADDR(FW_FLASH_BOOT_ADDR >> 2));
* Determines a card's PCI mode and associated parameters, such as speed
* and width.
*/
-static void __devinit get_pci_mode(struct adapter *adapter,
- struct pci_params *p)
+static void get_pci_mode(struct adapter *adapter, struct pci_params *p)
{
static unsigned short speed_map[] = { 33, 66, 100, 133 };
u32 pci_mode, pcie_cap;
* capabilities and default speed/duplex/flow-control/autonegotiation
* settings.
*/
-static void __devinit init_link_config(struct link_config *lc,
- unsigned int caps)
+static void init_link_config(struct link_config *lc, unsigned int caps)
{
lc->supported = caps;
lc->requested_speed = lc->speed = SPEED_INVALID;
* Calculates the size of an MC7 memory in bytes from the value of its
* configuration register.
*/
-static unsigned int __devinit mc7_calc_size(u32 cfg)
+static unsigned int mc7_calc_size(u32 cfg)
{
unsigned int width = G_WIDTH(cfg);
unsigned int banks = !!(cfg & F_BKS) + 1;
return MBs << 20;
}
-static void __devinit mc7_prep(struct adapter *adapter, struct mc7 *mc7,
- unsigned int base_addr, const char *name)
+static void mc7_prep(struct adapter *adapter, struct mc7 *mc7,
+ unsigned int base_addr, const char *name)
{
u32 cfg;
* Older PCIe cards lose their config space during reset, PCI-X
* ones don't.
*/
-static int t3_reset_adapter(struct adapter *adapter)
+int t3_reset_adapter(struct adapter *adapter)
{
int i, save_and_restore_pcie =
adapter->params.rev < T3_REV_B2 && is_pcie(adapter);
return 0;
}
-static int __devinit init_parity(struct adapter *adap)
+static int init_parity(struct adapter *adap)
{
int i, err, addr;
* for some adapter tunables, take PHYs out of reset, and initialize the MDIO
* interface.
*/
-int __devinit t3_prep_adapter(struct adapter *adapter,
- const struct adapter_info *ai, int reset)
+int t3_prep_adapter(struct adapter *adapter, const struct adapter_info *ai,
+ int reset)
{
int ret;
- unsigned int i, j = 0;
+ unsigned int i, j = -1;
get_pci_mode(adapter, &adapter->params.pci);
for_each_port(adapter, i) {
u8 hw_addr[6];
+ const struct port_type_info *pti;
struct port_info *p = adap2pinfo(adapter, i);
- while (!adapter->params.vpd.port_type[j])
- ++j;
+ while (!adapter->params.vpd.port_type[++j])
+ ;
- p->port_type = &port_types[adapter->params.vpd.port_type[j]];
- p->port_type->phy_prep(&p->phy, adapter, ai->phy_base_addr + j,
- ai->mdio_ops);
+ pti = &port_types[adapter->params.vpd.port_type[j]];
+ ret = pti->phy_prep(&p->phy, adapter, ai->phy_base_addr + j,
+ ai->mdio_ops);
+ if (ret)
+ return ret;
mac_prep(&p->mac, adapter, j);
- ++j;
/*
* The VPD EEPROM stores the base Ethernet address for the
ETH_ALEN);
memcpy(adapter->port[i]->perm_addr, hw_addr,
ETH_ALEN);
- init_link_config(&p->link_config, p->port_type->caps);
+ init_link_config(&p->link_config, p->phy.caps);
p->phy.ops->power_down(&p->phy, 1);
- if (!(p->port_type->caps & SUPPORTED_IRQ))
+ if (!(p->phy.caps & SUPPORTED_IRQ))
adapter->params.linkpoll_period = 10;
}
t3_set_reg_field(adapter, A_T3DBG_GPIO_EN, F_GPIO0_OUT_VAL,
F_GPIO0_OUT_VAL);
}
+
+int t3_replay_prep_adapter(struct adapter *adapter)
+{
+ const struct adapter_info *ai = adapter->params.info;
+ unsigned int i, j = -1;
+ int ret;
+
+ early_hw_init(adapter, ai);
+ ret = init_parity(adapter);
+ if (ret)
+ return ret;
+
+ for_each_port(adapter, i) {
+ const struct port_type_info *pti;
+ struct port_info *p = adap2pinfo(adapter, i);
+
+ while (!adapter->params.vpd.port_type[++j])
+ ;
+
+ pti = &port_types[adapter->params.vpd.port_type[j]];
+ ret = pti->phy_prep(&p->phy, adapter, p->phy.addr, NULL);
+ if (ret)
+ return ret;
+ p->phy.ops->power_down(&p->phy, 1);
+ }
+
+return 0;
+}
+
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff