/* bnx2x_reg.h: Broadcom Everest network driver.
*
- * Copyright (c) 2007-2008 Broadcom Corporation
+ * Copyright (c) 2007-2009 Broadcom Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation.
*
- * The registers description starts with the regsister Access type followed
+ * The registers description starts with the register Access type followed
* by size in bits. For example [RW 32]. The access types are:
* R - Read only
* RC - Clear on read
/* [RW 10] Write client 0: Assert pause threshold. */
#define BRB1_REG_PAUSE_LOW_THRESHOLD_0 0x60068
#define BRB1_REG_PAUSE_LOW_THRESHOLD_1 0x6006c
-/* [R 24] The number of full blocks occpied by port. */
+/* [R 24] The number of full blocks occupied by port. */
#define BRB1_REG_PORT_NUM_OCC_BLOCKS_0 0x60094
/* [RW 1] Reset the design by software. */
#define BRB1_REG_SOFT_RESET 0x600dc
#define MISC_REG_GPIO 0xa490
/* [R 28] this field hold the last information that caused reserved
attention. bits [19:0] - address; [22:20] function; [23] reserved;
- [27:24] the master thatcaused the attention - according to the following
+ [27:24] the master that caused the attention - according to the following
encodeing:1 = pxp; 2 = mcp; 3 = usdm; 4 = tsdm; 5 = xsdm; 6 = csdm; 7 =
dbu; 8 = dmae */
#define MISC_REG_GRC_RSV_ATTN 0xa3c0
/* [R 28] this field hold the last information that caused timeout
attention. bits [19:0] - address; [22:20] function; [23] reserved;
- [27:24] the master thatcaused the attention - according to the following
+ [27:24] the master that caused the attention - according to the following
encodeing:1 = pxp; 2 = mcp; 3 = usdm; 4 = tsdm; 5 = xsdm; 6 = csdm; 7 =
dbu; 8 = dmae */
#define MISC_REG_GRC_TIMEOUT_ATTN 0xa3c4
/* [RW 3] page size in L2P table for QM module; -4k; -8k; -16k; -32k; -64k;
-128k */
#define PXP2_REG_RQ_QM_P_SIZE 0x120050
-/* [RW 1] 1' indicates that the RBC has finished configurating the PSWRQ */
+/* [RW 1] 1' indicates that the RBC has finished configuring the PSWRQ */
#define PXP2_REG_RQ_RBC_DONE 0x1201b0
/* [RW 3] Max burst size filed for read requests port 0; 000 - 128B;
001:256B; 010: 512B; 11:1K:100:2K; 01:4K */
/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
buffer reaches this number has_payload will be asserted */
#define PXP2_REG_WR_DMAE_MPS 0x1205ec
-/* [RW 10] if Number of entries in dmae fifo will be higer than this
+/* [RW 10] if Number of entries in dmae fifo will be higher than this
threshold then has_payload indication will be asserted; the default value
should be equal to > write MBS size! */
#define PXP2_REG_WR_DMAE_TH 0x120368
/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
buffer reaches this number has_payload will be asserted */
#define PXP2_REG_WR_TSDM_MPS 0x1205d4
-/* [RW 10] if Number of entries in usdmdp fifo will be higer than this
+/* [RW 10] if Number of entries in usdmdp fifo will be higher than this
threshold then has_payload indication will be asserted; the default value
should be equal to > write MBS size! */
#define PXP2_REG_WR_USDMDP_TH 0x120348
#define XSEM_XSEM_INT_MASK_0_REG_ADDRESS_ERROR_SIZE 0
#define CFC_DEBUG1_REG_WRITE_AC (0x1<<4)
#define CFC_DEBUG1_REG_WRITE_AC_SIZE 4
-/* [R 1] debug only: This bit indicates wheter indicates that external
+/* [R 1] debug only: This bit indicates whether indicates that external
buffer was wrapped (oldest data was thrown); Relevant only when
~dbg_registers_debug_target=2 (PCI) & ~dbg_registers_full_mode=1 (wrap); */
#define DBG_REG_WRAP_ON_EXT_BUFFER 0xc124
#define DBG_REG_WRAP_ON_EXT_BUFFER_SIZE 1
-/* [R 1] debug only: This bit indicates wheter the internal buffer was
+/* [R 1] debug only: This bit indicates whether the internal buffer was
wrapped (oldest data was thrown) Relevant only when
~dbg_registers_debug_target=0 (internal buffer) */
#define DBG_REG_WRAP_ON_INT_BUFFER 0xc128
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff