address BRB1_IND_FREE_LIST_PRS_CRDT+1 initialize free tail. At address
BRB1_IND_FREE_LIST_PRS_CRDT+2 initialize parser initial credit. */
#define BRB1_REG_FREE_LIST_PRS_CRDT 0x60200
+/* [RW 10] The number of free blocks above which the High_llfc signal to
+ interface #n is de-asserted. */
+#define BRB1_REG_HIGH_LLFC_HIGH_THRESHOLD_0 0x6014c
+/* [RW 10] The number of free blocks below which the High_llfc signal to
+ interface #n is asserted. */
+#define BRB1_REG_HIGH_LLFC_LOW_THRESHOLD_0 0x6013c
/* [RW 23] LL RAM data. */
#define BRB1_REG_LL_RAM 0x61000
+/* [RW 10] The number of free blocks above which the Low_llfc signal to
+ interface #n is de-asserted. */
+#define BRB1_REG_LOW_LLFC_HIGH_THRESHOLD_0 0x6016c
+/* [RW 10] The number of free blocks below which the Low_llfc signal to
+ interface #n is asserted. */
+#define BRB1_REG_LOW_LLFC_LOW_THRESHOLD_0 0x6015c
/* [R 24] The number of full blocks. */
#define BRB1_REG_NUM_OF_FULL_BLOCKS 0x60090
/* [ST 32] The number of cycles that the write_full signal towards MAC #0
stands for weight 8 (the most prioritised); 1 stands for weight 1(least
prioritised); 2 stands for weight 2; tc. */
#define CCM_REG_CQM_P_WEIGHT 0xd00b8
+/* [RW 3] The weight of the QM (secondary) input in the WRR mechanism. 0
+ stands for weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define CCM_REG_CQM_S_WEIGHT 0xd00bc
/* [RW 1] Input SDM Interface enable. If 0 - the valid input is disregarded;
acknowledge output is deasserted; all other signals are treated as usual;
if 1 - normal activity. */
/* [RC 1] Set when the message length mismatch (relative to last indication)
at the SDM interface is detected. */
#define CCM_REG_CSDM_LENGTH_MIS 0xd0170
+/* [RW 3] The weight of the SDM input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define CCM_REG_CSDM_WEIGHT 0xd00b4
/* [RW 28] The CM header for QM formatting in case of an error in the QM
inputs. */
#define CCM_REG_ERR_CCM_HDR 0xd0094
/* [RC 1] Set when the message length mismatch (relative to last indication)
at the STORM interface is detected. */
#define CCM_REG_STORM_LENGTH_MIS 0xd016c
+/* [RW 3] The weight of the STORM input in the WRR (Weighted Round robin)
+ mechanism. 0 stands for weight 8 (the most prioritised); 1 stands for
+ weight 1(least prioritised); 2 stands for weight 2 (more prioritised);
+ tc. */
+#define CCM_REG_STORM_WEIGHT 0xd009c
/* [RW 1] Input tsem Interface enable. If 0 - the valid input is
disregarded; acknowledge output is deasserted; all other signals are
treated as usual; if 1 - normal activity. */
set one of these bits. the bit description can be found in CFC
specifications */
#define CFC_REG_ERROR_VECTOR 0x10403c
+/* [WB 93] LCID info ram access */
+#define CFC_REG_INFO_RAM 0x105000
+#define CFC_REG_INFO_RAM_SIZE 1024
#define CFC_REG_INIT_REG 0x10404c
+#define CFC_REG_INTERFACES 0x104058
/* [RW 24] {weight_load_client7[2:0] to weight_load_client0[2:0]}. this
field allows changing the priorities of the weighted-round-robin arbiter
which selects which CFC load client should be served next */
#define CFC_REG_NUM_LCIDS_ALLOC 0x104020
/* [R 9] Number of Arriving LCIDs in Link List Block */
#define CFC_REG_NUM_LCIDS_ARRIVING 0x104004
-/* [R 9] Number of Inside LCIDs in Link List Block */
-#define CFC_REG_NUM_LCIDS_INSIDE 0x104008
/* [R 9] Number of Leaving LCIDs in Link List Block */
#define CFC_REG_NUM_LCIDS_LEAVING 0x104018
/* [RW 8] The event id for aggregated interrupt 0 */
#define DORQ_REG_SHRT_CMHEAD 0x170054
#define HC_CONFIG_0_REG_ATTN_BIT_EN_0 (0x1<<4)
#define HC_CONFIG_0_REG_INT_LINE_EN_0 (0x1<<3)
+#define HC_CONFIG_0_REG_MSI_ATTN_EN_0 (0x1<<7)
#define HC_CONFIG_0_REG_MSI_MSIX_INT_EN_0 (0x1<<2)
#define HC_CONFIG_0_REG_SINGLE_ISR_EN_0 (0x1<<1)
#define HC_REG_AGG_INT_0 0x108050
This is the result value of the pin; not the drive value. Writing these
bits will have not effect. */
#define MISC_REG_GPIO 0xa490
+/* [RW 8] These bits enable the GPIO_INTs to signals event to the
+ IGU/MCP.according to the following map: [0] p0_gpio_0; [1] p0_gpio_1; [2]
+ p0_gpio_2; [3] p0_gpio_3; [4] p1_gpio_0; [5] p1_gpio_1; [6] p1_gpio_2;
+ [7] p1_gpio_3; */
+#define MISC_REG_GPIO_EVENT_EN 0xa2bc
+/* [RW 32] GPIO INT. [31-28] OLD_CLR port1; [27-24] OLD_CLR port0; Writing a
+ '1' to these bit clears the corresponding bit in the #OLD_VALUE register.
+ This will acknowledge an interrupt on the falling edge of corresponding
+ GPIO input (reset value 0). [23-16] OLD_SET [23-16] port1; OLD_SET port0;
+ Writing a '1' to these bit sets the corresponding bit in the #OLD_VALUE
+ register. This will acknowledge an interrupt on the rising edge of
+ corresponding SPIO input (reset value 0). [15-12] OLD_VALUE [11-8] port1;
+ OLD_VALUE port0; RO; These bits indicate the old value of the GPIO input
+ value. When the ~INT_STATE bit is set; this bit indicates the OLD value
+ of the pin such that if ~INT_STATE is set and this bit is '0'; then the
+ interrupt is due to a low to high edge. If ~INT_STATE is set and this bit
+ is '1'; then the interrupt is due to a high to low edge (reset value 0).
+ [7-4] INT_STATE port1; [3-0] INT_STATE RO port0; These bits indicate the
+ current GPIO interrupt state for each GPIO pin. This bit is cleared when
+ the appropriate #OLD_SET or #OLD_CLR command bit is written. This bit is
+ set when the GPIO input does not match the current value in #OLD_VALUE
+ (reset value 0). */
+#define MISC_REG_GPIO_INT 0xa494
/* [R 28] this field hold the last information that caused reserved
attention. bits [19:0] - address; [22:20] function; [23] reserved;
[27:24] the master that caused the attention - according to the following
command bit is written. This bit is set when the SPIO input does not
match the current value in #OLD_VALUE (reset value 0). */
#define MISC_REG_SPIO_INT 0xa500
+/* [RW 32] reload value for counter 4 if reload; the value will be reload if
+ the counter reached zero and the reload bit
+ (~misc_registers_sw_timer_cfg_4.sw_timer_cfg_4[1] ) is set */
+#define MISC_REG_SW_TIMER_RELOAD_VAL_4 0xa2fc
+/* [RW 32] the value of the counter for sw timers1-8. there are 8 addresses
+ in this register. addres 0 - timer 1; address - timer 2�address 7 -
+ timer 8 */
+#define MISC_REG_SW_TIMER_VAL 0xa5c0
/* [RW 1] Set by the MCP to remember if one or more of the drivers is/are
loaded; 0-prepare; -unprepare */
#define MISC_REG_UNPREPARED 0xa424
/* [RW 4] led mode for port0: 0 MAC; 1-3 PHY1; 4 MAC2; 5-7 PHY4; 8-MAC3;
9-11PHY7; 12 MAC4; 13-15 PHY10; */
#define NIG_REG_LED_MODE_P0 0x102f0
+/* [RW 3] for port0 enable for llfc ppp and pause. b0 - brb1 enable; b1-
+ tsdm enable; b2- usdm enable */
+#define NIG_REG_LLFC_EGRESS_SRC_ENABLE_0 0x16070
+/* [RW 1] SAFC enable for port0. This register may get 1 only when
+ ~ppp_enable.ppp_enable = 0 and pause_enable.pause_enable =0 for the same
+ port */
+#define NIG_REG_LLFC_ENABLE_0 0x16208
+/* [RW 16] classes are high-priority for port0 */
+#define NIG_REG_LLFC_HIGH_PRIORITY_CLASSES_0 0x16058
+/* [RW 16] classes are low-priority for port0 */
+#define NIG_REG_LLFC_LOW_PRIORITY_CLASSES_0 0x16060
+/* [RW 1] Output enable of message to LLFC BMAC IF for port0 */
+#define NIG_REG_LLFC_OUT_EN_0 0x160c8
#define NIG_REG_LLH0_ACPI_PAT_0_CRC 0x1015c
#define NIG_REG_LLH0_ACPI_PAT_6_LEN 0x10154
#define NIG_REG_LLH0_BRB1_DRV_MASK 0x10244
#define NIG_REG_NIG_INT_STS_1 0x103c0
/* [R 32] Parity register #0 read */
#define NIG_REG_NIG_PRTY_STS 0x103d0
+/* [RW 1] Pause enable for port0. This register may get 1 only when
+ ~safc_enable.safc_enable = 0 and ppp_enable.ppp_enable =0 for the same
+ port */
+#define NIG_REG_PAUSE_ENABLE_0 0x160c0
/* [RW 1] Input enable for RX PBF LP IF */
#define NIG_REG_PBF_LB_IN_EN 0x100b4
/* [RW 1] Value of this register will be transmitted to port swap when
#define NIG_REG_PRS_EOP_OUT_EN 0x10104
/* [RW 1] Input enable for RX parser request IF */
#define NIG_REG_PRS_REQ_IN_EN 0x100b8
+/* [RW 5] control to serdes - CL45 DEVAD */
+#define NIG_REG_SERDES0_CTRL_MD_DEVAD 0x10370
+/* [RW 1] control to serdes; 0 - clause 45; 1 - clause 22 */
+#define NIG_REG_SERDES0_CTRL_MD_ST 0x1036c
/* [RW 5] control to serdes - CL22 PHY_ADD and CL45 PRTAD */
#define NIG_REG_SERDES0_CTRL_PHY_ADDR 0x10374
/* [R 1] status from serdes0 that inputs to interrupt logic of link status */
#define PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_2 0x400e4
#define PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_3 0x400e8
#define PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_4 0x400ec
+#define PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_5 0x400f0
/* [RW 32] The CM header for flush message where 'load existed' bit in CFC
load response is set and packet type is 0. Used in packet start message
to TCM. */
#define PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_2 0x400c4
#define PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_3 0x400c8
#define PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_4 0x400cc
+#define PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_5 0x400d0
/* [RW 32] The CM header for a match and packet type 1 for loopback port.
Used in packet start message to TCM. */
#define PRS_REG_CM_HDR_LOOPBACK_TYPE_1 0x4009c
#define PXP2_REG_PGL_INT_XSDM_5 0x1204e8
#define PXP2_REG_PGL_INT_XSDM_6 0x1204ec
#define PXP2_REG_PGL_INT_XSDM_7 0x1204f0
+/* [RW 3] this field allows one function to pretend being another function
+ when accessing any BAR mapped resource within the device. the value of
+ the field is the number of the function that will be accessed
+ effectively. after software write to this bit it must read it in order to
+ know that the new value is updated */
+#define PXP2_REG_PGL_PRETEND_FUNC_F0 0x120674
+#define PXP2_REG_PGL_PRETEND_FUNC_F1 0x120678
+#define PXP2_REG_PGL_PRETEND_FUNC_F2 0x12067c
+#define PXP2_REG_PGL_PRETEND_FUNC_F3 0x120680
+#define PXP2_REG_PGL_PRETEND_FUNC_F4 0x120684
+#define PXP2_REG_PGL_PRETEND_FUNC_F5 0x120688
+#define PXP2_REG_PGL_PRETEND_FUNC_F6 0x12068c
+#define PXP2_REG_PGL_PRETEND_FUNC_F7 0x120690
/* [R 1] this bit indicates that a read request was blocked because of
bus_master_en was deasserted */
#define PXP2_REG_PGL_READ_BLOCKED 0x120568
considered zero so practically there are only 20 bits in this register;
queues 63-0 */
#define QM_REG_BASEADDR 0x168900
+/* [RW 32] The base logical address (in bytes) of each physical queue. The
+ index I represents the physical queue number. The 12 lsbs are ignore and
+ considered zero so practically there are only 20 bits in this register;
+ queues 127-64 */
+#define QM_REG_BASEADDR_EXT_A 0x16e100
/* [RW 16] The byte credit cost for each task. This value is for both ports */
#define QM_REG_BYTECRDCOST 0x168234
/* [RW 16] The initial byte credit value for both ports. */
#define SRC_REG_KEYRSS0_0 0x40408
#define SRC_REG_KEYRSS0_7 0x40424
#define SRC_REG_KEYRSS1_9 0x40454
+#define SRC_REG_KEYSEARCH_0 0x40458
+#define SRC_REG_KEYSEARCH_1 0x4045c
+#define SRC_REG_KEYSEARCH_2 0x40460
+#define SRC_REG_KEYSEARCH_3 0x40464
+#define SRC_REG_KEYSEARCH_4 0x40468
+#define SRC_REG_KEYSEARCH_5 0x4046c
+#define SRC_REG_KEYSEARCH_6 0x40470
+#define SRC_REG_KEYSEARCH_7 0x40474
+#define SRC_REG_KEYSEARCH_8 0x40478
+#define SRC_REG_KEYSEARCH_9 0x4047c
#define SRC_REG_LASTFREE0 0x40530
#define SRC_REG_NUMBER_HASH_BITS0 0x40400
/* [RW 1] Reset internal state machines. */
/* [RC 1] Message length mismatch (relative to last indication) at the In#9
interface. */
#define TCM_REG_CSEM_LENGTH_MIS 0x50174
+/* [RW 3] The weight of the input csem in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define TCM_REG_CSEM_WEIGHT 0x500bc
/* [RW 8] The Event ID in case of ErrorFlg is set in the input message. */
#define TCM_REG_ERR_EVNT_ID 0x500a0
/* [RW 28] The CM erroneous header for QM and Timers formatting. */
#define TCM_REG_N_SM_CTX_LD_2 0x50058
#define TCM_REG_N_SM_CTX_LD_3 0x5005c
#define TCM_REG_N_SM_CTX_LD_4 0x50060
+#define TCM_REG_N_SM_CTX_LD_5 0x50064
/* [RW 1] Input pbf Interface enable. If 0 - the valid input is disregarded;
acknowledge output is deasserted; all other signals are treated as usual;
if 1 - normal activity. */
disregarded; acknowledge output is deasserted; all other signals are
treated as usual; if 1 - normal activity. */
#define TCM_REG_STORM_TCM_IFEN 0x50010
+/* [RW 3] The weight of the STORM input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define TCM_REG_STORM_WEIGHT 0x500ac
/* [RW 1] CM - CFC Interface enable. If 0 - the valid input is disregarded;
acknowledge output is deasserted; all other signals are treated as usual;
if 1 - normal activity. */
disregarded; acknowledge output is deasserted; all other signals are
treated as usual; if 1 - normal activity. */
#define TCM_REG_TM_TCM_IFEN 0x5001c
+/* [RW 3] The weight of the Timers input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define TCM_REG_TM_WEIGHT 0x500d0
/* [RW 6] QM output initial credit. Max credit available - 32.Write writes
the initial credit value; read returns the current value of the credit
counter. Must be initialized to 32 at start-up. */
#define TCM_REG_TQM_INIT_CRD 0x5021c
+/* [RW 3] The weight of the QM (primary) input in the WRR mechanism. 0
+ stands for weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define TCM_REG_TQM_P_WEIGHT 0x500c8
+/* [RW 3] The weight of the QM (secondary) input in the WRR mechanism. 0
+ stands for weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define TCM_REG_TQM_S_WEIGHT 0x500cc
/* [RW 28] The CM header value for QM request (primary). */
#define TCM_REG_TQM_TCM_HDR_P 0x50090
/* [RW 28] The CM header value for QM request (secondary). */
/* [RC 1] Message length mismatch (relative to last indication) at the In#8
interface. */
#define TCM_REG_USEM_LENGTH_MIS 0x50170
+/* [RW 3] The weight of the input usem in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define TCM_REG_USEM_WEIGHT 0x500b8
/* [RW 21] Indirect access to the descriptor table of the XX protection
mechanism. The fields are: [5:0] - length of the message; 15:6] - message
pointer; 20:16] - next pointer. */
#define TM_REG_EN_CL1_INPUT 0x16400c
/* [RW 1] Enable client2 input. */
#define TM_REG_EN_CL2_INPUT 0x164010
+#define TM_REG_EN_LINEAR0_TIMER 0x164014
/* [RW 1] Enable real time counter. */
#define TM_REG_EN_REAL_TIME_CNT 0x1640d8
/* [RW 1] Enable for Timers state machines. */
/* [RW 4] Load value for expiration credit cnt. CFC max number of
outstanding load requests for timers (expiration) context loading. */
#define TM_REG_EXP_CRDCNT_VAL 0x164238
+/* [RW 32] Linear0 logic address. */
+#define TM_REG_LIN0_LOGIC_ADDR 0x164240
/* [RW 18] Linear0 Max active cid (in banks of 32 entries). */
#define TM_REG_LIN0_MAX_ACTIVE_CID 0x164048
/* [WB 64] Linear0 phy address. */
#define TM_REG_LIN0_PHY_ADDR 0x164270
+/* [RW 1] Linear0 physical address valid. */
+#define TM_REG_LIN0_PHY_ADDR_VALID 0x164248
/* [RW 24] Linear0 array scan timeout. */
#define TM_REG_LIN0_SCAN_TIME 0x16403c
+/* [RW 32] Linear1 logic address. */
+#define TM_REG_LIN1_LOGIC_ADDR 0x164250
/* [WB 64] Linear1 phy address. */
#define TM_REG_LIN1_PHY_ADDR 0x164280
+/* [RW 1] Linear1 physical address valid. */
+#define TM_REG_LIN1_PHY_ADDR_VALID 0x164258
/* [RW 6] Linear timer set_clear fifo threshold. */
#define TM_REG_LIN_SETCLR_FIFO_ALFULL_THR 0x164070
/* [RW 2] Load value for pci arbiter credit cnt. */
#define TM_REG_TM_INT_STS 0x1640f0
/* [RW 8] The event id for aggregated interrupt 0 */
#define TSDM_REG_AGG_INT_EVENT_0 0x42038
+#define TSDM_REG_AGG_INT_EVENT_1 0x4203c
+#define TSDM_REG_AGG_INT_EVENT_10 0x42060
+#define TSDM_REG_AGG_INT_EVENT_11 0x42064
+#define TSDM_REG_AGG_INT_EVENT_12 0x42068
+#define TSDM_REG_AGG_INT_EVENT_13 0x4206c
+#define TSDM_REG_AGG_INT_EVENT_14 0x42070
+#define TSDM_REG_AGG_INT_EVENT_15 0x42074
+#define TSDM_REG_AGG_INT_EVENT_16 0x42078
+#define TSDM_REG_AGG_INT_EVENT_17 0x4207c
+#define TSDM_REG_AGG_INT_EVENT_18 0x42080
+#define TSDM_REG_AGG_INT_EVENT_19 0x42084
#define TSDM_REG_AGG_INT_EVENT_2 0x42040
#define TSDM_REG_AGG_INT_EVENT_20 0x42088
#define TSDM_REG_AGG_INT_EVENT_21 0x4208c
#define TSDM_REG_AGG_INT_EVENT_30 0x420b0
#define TSDM_REG_AGG_INT_EVENT_31 0x420b4
#define TSDM_REG_AGG_INT_EVENT_4 0x42048
+/* [RW 1] The T bit for aggregated interrupt 0 */
+#define TSDM_REG_AGG_INT_T_0 0x420b8
+#define TSDM_REG_AGG_INT_T_1 0x420bc
+#define TSDM_REG_AGG_INT_T_10 0x420e0
+#define TSDM_REG_AGG_INT_T_11 0x420e4
+#define TSDM_REG_AGG_INT_T_12 0x420e8
+#define TSDM_REG_AGG_INT_T_13 0x420ec
+#define TSDM_REG_AGG_INT_T_14 0x420f0
+#define TSDM_REG_AGG_INT_T_15 0x420f4
+#define TSDM_REG_AGG_INT_T_16 0x420f8
+#define TSDM_REG_AGG_INT_T_17 0x420fc
+#define TSDM_REG_AGG_INT_T_18 0x42100
+#define TSDM_REG_AGG_INT_T_19 0x42104
/* [RW 13] The start address in the internal RAM for the cfc_rsp lcid */
#define TSDM_REG_CFC_RSP_START_ADDR 0x42008
/* [RW 16] The maximum value of the competion counter #0 */
/* [RC 1] Set when the message length mismatch (relative to last indication)
at the dorq interface is detected. */
#define UCM_REG_DORQ_LENGTH_MIS 0xe0168
+/* [RW 3] The weight of the input dorq in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define UCM_REG_DORQ_WEIGHT 0xe00c0
/* [RW 8] The Event ID in case ErrorFlg input message bit is set. */
#define UCM_REG_ERR_EVNT_ID 0xe00a4
/* [RW 28] The CM erroneous header for QM and Timers formatting. */
disregarded; acknowledge output is deasserted; all other signals are
treated as usual; if 1 - normal activity. */
#define UCM_REG_STORM_UCM_IFEN 0xe0010
+/* [RW 3] The weight of the STORM input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define UCM_REG_STORM_WEIGHT 0xe00b0
/* [RW 4] Timers output initial credit. Max credit available - 15.Write
writes the initial credit value; read returns the current value of the
credit counter. Must be initialized to 4 at start-up. */
disregarded; acknowledge output is deasserted; all other signals are
treated as usual; if 1 - normal activity. */
#define UCM_REG_TM_UCM_IFEN 0xe001c
+/* [RW 3] The weight of the Timers input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define UCM_REG_TM_WEIGHT 0xe00d4
/* [RW 1] Input tsem Interface enable. If 0 - the valid input is
disregarded; acknowledge output is deasserted; all other signals are
treated as usual; if 1 - normal activity. */
stands for weight 8 (the most prioritised); 1 stands for weight 1(least
prioritised); 2 stands for weight 2; tc. */
#define UCM_REG_UQM_P_WEIGHT 0xe00cc
+/* [RW 3] The weight of the QM (secondary) input in the WRR mechanism. 0
+ stands for weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define UCM_REG_UQM_S_WEIGHT 0xe00d0
/* [RW 28] The CM header value for QM request (primary). */
#define UCM_REG_UQM_UCM_HDR_P 0xe0094
/* [RW 28] The CM header value for QM request (secondary). */
/* [RC 1] Set when the message length mismatch (relative to last indication)
at the SDM interface is detected. */
#define UCM_REG_USDM_LENGTH_MIS 0xe0158
+/* [RW 3] The weight of the SDM input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define UCM_REG_USDM_WEIGHT 0xe00c8
/* [RW 1] Input xsem Interface enable. If 0 - the valid input is
disregarded; acknowledge output is deasserted; all other signals are
treated as usual; if 1 - normal activity. */
/* [RC 1] Set when the message length mismatch (relative to last indication)
at the xsem interface isdetected. */
#define UCM_REG_XSEM_LENGTH_MIS 0xe0164
+/* [RW 3] The weight of the input xsem in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define UCM_REG_XSEM_WEIGHT 0xe00bc
/* [RW 20] Indirect access to the descriptor table of the XX protection
mechanism. The fields are:[5:0] - message length; 14:6] - message
pointer; 19:15] - next pointer. */
#define USDM_REG_AGG_INT_EVENT_30 0xc40b0
#define USDM_REG_AGG_INT_EVENT_31 0xc40b4
#define USDM_REG_AGG_INT_EVENT_4 0xc4048
+#define USDM_REG_AGG_INT_EVENT_5 0xc404c
/* [RW 1] For each aggregated interrupt index whether the mode is normal (0)
or auto-mask-mode (1) */
#define USDM_REG_AGG_INT_MODE_0 0xc41b8
#define USDM_REG_AGG_INT_MODE_17 0xc41fc
#define USDM_REG_AGG_INT_MODE_18 0xc4200
#define USDM_REG_AGG_INT_MODE_19 0xc4204
+#define USDM_REG_AGG_INT_MODE_4 0xc41c8
+#define USDM_REG_AGG_INT_MODE_5 0xc41cc
/* [RW 13] The start address in the internal RAM for the cfc_rsp lcid */
#define USDM_REG_CFC_RSP_START_ADDR 0xc4008
/* [RW 16] The maximum value of the competion counter #0 */
/* [RC 1] Set at message length mismatch (relative to last indication) at
the dorq interface. */
#define XCM_REG_DORQ_LENGTH_MIS 0x20230
+/* [RW 3] The weight of the input dorq in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define XCM_REG_DORQ_WEIGHT 0x200cc
/* [RW 8] The Event ID in case the ErrorFlg input message bit is set. */
#define XCM_REG_ERR_EVNT_ID 0x200b0
/* [RW 28] The CM erroneous header for QM and Timers formatting. */
/* [RC 1] Set at message length mismatch (relative to last indication) at
the nig0 interface. */
#define XCM_REG_NIG0_LENGTH_MIS 0x20238
+/* [RW 3] The weight of the input nig0 in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define XCM_REG_NIG0_WEIGHT 0x200d4
/* [RW 1] Input nig1 Interface enable. If 0 - the valid input is
disregarded; acknowledge output is deasserted; all other signals are
treated as usual; if 1 - normal activity. */
writes the initial credit value; read returns the current value of the
credit counter. Must be initialized to 4 at start-up. */
#define XCM_REG_TM_INIT_CRD 0x2041c
+/* [RW 3] The weight of the Timers input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define XCM_REG_TM_WEIGHT 0x200ec
/* [RW 28] The CM header for Timers expiration command. */
#define XCM_REG_TM_XCM_HDR 0x200a8
/* [RW 1] Timers - CM Interface enable. If 0 - the valid input is
stands for weight 8 (the most prioritised); 1 stands for weight 1(least
prioritised); 2 stands for weight 2; tc. */
#define XCM_REG_XQM_P_WEIGHT 0x200e4
+/* [RW 3] The weight of the QM (secondary) input in the WRR mechanism. 0
+ stands for weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define XCM_REG_XQM_S_WEIGHT 0x200e8
/* [RW 28] The CM header value for QM request (primary). */
#define XCM_REG_XQM_XCM_HDR_P 0x200a0
/* [RW 28] The CM header value for QM request (secondary). */
#define XSDM_REG_AGG_INT_EVENT_10 0x166060
#define XSDM_REG_AGG_INT_EVENT_11 0x166064
#define XSDM_REG_AGG_INT_EVENT_12 0x166068
+#define XSDM_REG_AGG_INT_EVENT_13 0x16606c
+#define XSDM_REG_AGG_INT_EVENT_14 0x166070
#define XSDM_REG_AGG_INT_EVENT_2 0x166040
#define XSDM_REG_AGG_INT_EVENT_20 0x166088
#define XSDM_REG_AGG_INT_EVENT_21 0x16608c
#define EMAC_RX_MODE_FLOW_EN (1L<<2)
#define EMAC_RX_MODE_KEEP_VLAN_TAG (1L<<10)
#define EMAC_RX_MODE_PROMISCUOUS (1L<<8)
+#define EMAC_RX_MODE_RESET (1L<<0)
#define EMAC_RX_MTU_SIZE_JUMBO_ENA (1L<<31)
#define EMAC_TX_MODE_EXT_PAUSE_EN (1L<<3)
#define EMAC_TX_MODE_FLOW_EN (1L<<4)
+#define EMAC_TX_MODE_RESET (1L<<0)
#define MISC_REGISTERS_GPIO_0 0
#define MISC_REGISTERS_GPIO_1 1
#define MISC_REGISTERS_GPIO_2 2
#define MISC_REGISTERS_GPIO_FLOAT_POS 24
#define MISC_REGISTERS_GPIO_HIGH 1
#define MISC_REGISTERS_GPIO_INPUT_HI_Z 2
+#define MISC_REGISTERS_GPIO_INT_CLR_POS 24
+#define MISC_REGISTERS_GPIO_INT_OUTPUT_CLR 0
+#define MISC_REGISTERS_GPIO_INT_OUTPUT_SET 1
+#define MISC_REGISTERS_GPIO_INT_SET_POS 16
#define MISC_REGISTERS_GPIO_LOW 0
#define MISC_REGISTERS_GPIO_OUTPUT_HIGH 1
#define MISC_REGISTERS_GPIO_OUTPUT_LOW 0
#define MISC_REGISTERS_SPIO_OUTPUT_LOW 0
#define MISC_REGISTERS_SPIO_SET_POS 8
#define HW_LOCK_MAX_RESOURCE_VALUE 31
-#define HW_LOCK_RESOURCE_8072_MDIO 0
#define HW_LOCK_RESOURCE_GPIO 1
+#define HW_LOCK_RESOURCE_MDIO 0
#define HW_LOCK_RESOURCE_PORT0_ATT_MASK 3
#define HW_LOCK_RESOURCE_SPIO 2
#define HW_LOCK_RESOURCE_UNDI 5
+#define PRS_FLAG_OVERETH_IPV4 1
#define AEU_INPUTS_ATTN_BITS_BRB_PARITY_ERROR (1<<18)
#define AEU_INPUTS_ATTN_BITS_CCM_HW_INTERRUPT (1<<31)
#define AEU_INPUTS_ATTN_BITS_CDU_HW_INTERRUPT (1<<9)
#define AEU_INPUTS_ATTN_BITS_DMAE_HW_INTERRUPT (1<<11)
#define AEU_INPUTS_ATTN_BITS_DOORBELLQ_HW_INTERRUPT (1<<13)
#define AEU_INPUTS_ATTN_BITS_DOORBELLQ_PARITY_ERROR (1<<12)
+#define AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_0 (1<<5)
+#define AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_1 (1<<9)
#define AEU_INPUTS_ATTN_BITS_IGU_PARITY_ERROR (1<<12)
#define AEU_INPUTS_ATTN_BITS_MISC_HW_INTERRUPT (1<<15)
#define AEU_INPUTS_ATTN_BITS_MISC_PARITY_ERROR (1<<14)
#define PCICFG_COMMAND_INT_DISABLE (1<<10)
#define PCICFG_COMMAND_RESERVED (0x1f<<11)
#define PCICFG_STATUS_OFFSET 0x06
-#define PCICFG_REVESION_ID 0x08
+#define PCICFG_REVESION_ID_OFFSET 0x08
#define PCICFG_CACHE_LINE_SIZE 0x0c
#define PCICFG_LATENCY_TIMER 0x0d
#define PCICFG_BAR_1_LOW 0x10
#define PCICFG_PM_CSR_STATE (0x3<<0)
#define PCICFG_PM_CSR_PME_ENABLE (1<<8)
#define PCICFG_PM_CSR_PME_STATUS (1<<15)
+#define PCICFG_MSI_CAP_ID_OFFSET 0x58
+#define PCICFG_MSI_CONTROL_ENABLE (0x1<<16)
+#define PCICFG_MSI_CONTROL_MCAP (0x7<<17)
+#define PCICFG_MSI_CONTROL_MENA (0x7<<20)
+#define PCICFG_MSI_CONTROL_64_BIT_ADDR_CAP (0x1<<23)
+#define PCICFG_MSI_CONTROL_MSI_PVMASK_CAPABLE (0x1<<24)
#define PCICFG_GRC_ADDRESS 0x78
#define PCICFG_GRC_DATA 0x80
+#define PCICFG_MSIX_CAP_ID_OFFSET 0xa0
+#define PCICFG_MSIX_CONTROL_TABLE_SIZE (0x7ff<<16)
+#define PCICFG_MSIX_CONTROL_RESERVED (0x7<<27)
+#define PCICFG_MSIX_CONTROL_FUNC_MASK (0x1<<30)
+#define PCICFG_MSIX_CONTROL_MSIX_ENABLE (0x1<<31)
+
#define PCICFG_DEVICE_CONTROL 0xb4
+#define PCICFG_DEVICE_STATUS 0xb6
+#define PCICFG_DEVICE_STATUS_CORR_ERR_DET (1<<0)
+#define PCICFG_DEVICE_STATUS_NON_FATAL_ERR_DET (1<<1)
+#define PCICFG_DEVICE_STATUS_FATAL_ERR_DET (1<<2)
+#define PCICFG_DEVICE_STATUS_UNSUP_REQ_DET (1<<3)
+#define PCICFG_DEVICE_STATUS_AUX_PWR_DET (1<<4)
+#define PCICFG_DEVICE_STATUS_NO_PEND (1<<5)
#define PCICFG_LINK_CONTROL 0xbc
#define MDIO_TX0_TX_DRIVER_IFULLSPD_SHIFT 1
#define MDIO_TX0_TX_DRIVER_ICBUF1T 1
+#define MDIO_REG_BANK_TX1 0x8070
+#define MDIO_TX1_TX_DRIVER 0x17
+#define MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK 0xf000
+#define MDIO_TX0_TX_DRIVER_PREEMPHASIS_SHIFT 12
+#define MDIO_TX0_TX_DRIVER_IDRIVER_MASK 0x0f00
+#define MDIO_TX0_TX_DRIVER_IDRIVER_SHIFT 8
+#define MDIO_TX0_TX_DRIVER_IPREDRIVER_MASK 0x00f0
+#define MDIO_TX0_TX_DRIVER_IPREDRIVER_SHIFT 4
+#define MDIO_TX0_TX_DRIVER_IFULLSPD_MASK 0x000e
+#define MDIO_TX0_TX_DRIVER_IFULLSPD_SHIFT 1
+#define MDIO_TX0_TX_DRIVER_ICBUF1T 1
+
+#define MDIO_REG_BANK_TX2 0x8080
+#define MDIO_TX2_TX_DRIVER 0x17
+#define MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK 0xf000
+#define MDIO_TX0_TX_DRIVER_PREEMPHASIS_SHIFT 12
+#define MDIO_TX0_TX_DRIVER_IDRIVER_MASK 0x0f00
+#define MDIO_TX0_TX_DRIVER_IDRIVER_SHIFT 8
+#define MDIO_TX0_TX_DRIVER_IPREDRIVER_MASK 0x00f0
+#define MDIO_TX0_TX_DRIVER_IPREDRIVER_SHIFT 4
+#define MDIO_TX0_TX_DRIVER_IFULLSPD_MASK 0x000e
+#define MDIO_TX0_TX_DRIVER_IFULLSPD_SHIFT 1
+#define MDIO_TX0_TX_DRIVER_ICBUF1T 1
+
+#define MDIO_REG_BANK_TX3 0x8090
+#define MDIO_TX3_TX_DRIVER 0x17
+#define MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK 0xf000
+#define MDIO_TX0_TX_DRIVER_PREEMPHASIS_SHIFT 12
+#define MDIO_TX0_TX_DRIVER_IDRIVER_MASK 0x0f00
+#define MDIO_TX0_TX_DRIVER_IDRIVER_SHIFT 8
+#define MDIO_TX0_TX_DRIVER_IPREDRIVER_MASK 0x00f0
+#define MDIO_TX0_TX_DRIVER_IPREDRIVER_SHIFT 4
+#define MDIO_TX0_TX_DRIVER_IFULLSPD_MASK 0x000e
+#define MDIO_TX0_TX_DRIVER_IFULLSPD_SHIFT 1
+#define MDIO_TX0_TX_DRIVER_ICBUF1T 1
+
#define MDIO_REG_BANK_XGXS_BLOCK0 0x8000
#define MDIO_BLOCK0_XGXS_CONTROL 0x10
#define MDIO_PMA_REG_ROM_VER2 0xca1a
#define MDIO_PMA_REG_EDC_FFE_MAIN 0xca1b
#define MDIO_PMA_REG_PLL_BANDWIDTH 0xca1d
+#define MDIO_PMA_REG_GEN_CTRL2 0xca1e
+#define MDIO_PMA_REG_MISC_CTRL0 0xca23
+#define MDIO_PMA_REG_LRM_MODE 0xca3f
#define MDIO_PMA_REG_CDR_BANDWIDTH 0xca46
#define MDIO_PMA_REG_MISC_CTRL1 0xca85
+#define MDIO_PMA_REG_8726_TWO_WIRE_CTRL 0x8000
+#define MDIO_PMA_REG_8726_TWO_WIRE_CTRL_STATUS_MASK 0x000c
+#define MDIO_PMA_REG_8726_TWO_WIRE_STATUS_IDLE 0x0000
+#define MDIO_PMA_REG_8726_TWO_WIRE_STATUS_COMPLETE 0x0004
+#define MDIO_PMA_REG_8726_TWO_WIRE_STATUS_IN_PROGRESS 0x0008
+#define MDIO_PMA_REG_8726_TWO_WIRE_STATUS_FAILED 0x000c
+#define MDIO_PMA_REG_8726_TWO_WIRE_BYTE_CNT 0x8002
+#define MDIO_PMA_REG_8726_TWO_WIRE_MEM_ADDR 0x8003
+#define MDIO_PMA_REG_8726_TWO_WIRE_DATA_BUF 0xc820
+#define MDIO_PMA_REG_8726_TWO_WIRE_DATA_MASK 0xff
+#define MDIO_PMA_REG_8726_TX_CTRL1 0xca01
+#define MDIO_PMA_REG_8726_TX_CTRL2 0xca05
+
+
+#define MDIO_PMA_REG_8073_CHIP_REV 0xc801
+#define MDIO_PMA_REG_8073_SPEED_LINK_STATUS 0xc820
+#define MDIO_PMA_REG_8073_XAUI_WA 0xc841
+
#define MDIO_PMA_REG_7101_RESET 0xc000
#define MDIO_PMA_REG_7107_LED_CNTL 0xc007
#define MDIO_PMA_REG_7101_VER1 0xc026
#define MDIO_XS_PLL_SEQUENCER 0x8000
#define MDIO_XS_SFX7101_XGXS_TEST1 0xc00a
+#define MDIO_XS_8706_REG_BANK_RX0 0x80bc
+#define MDIO_XS_8706_REG_BANK_RX1 0x80cc
+#define MDIO_XS_8706_REG_BANK_RX2 0x80dc
+#define MDIO_XS_8706_REG_BANK_RX3 0x80ec
+#define MDIO_XS_8706_REG_BANK_RXA 0x80fc
+
#define MDIO_AN_DEVAD 0x7
/*ieee*/
#define MDIO_AN_REG_CTRL 0x0000
#define MDIO_AN_REG_CL37_FC_LD 0xffe4
#define MDIO_AN_REG_CL37_FC_LP 0xffe5
+#define MDIO_AN_REG_8073_2_5G 0x8329
+
#define IGU_FUNC_BASE 0x0400
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff