#define SWITCH_CFG_AUTO_DETECT PORT_FEATURE_CON_SWITCH_AUTO_DETECT
u16 hw_led_mode; /* part of the hw_config read from the shmem */
+
+ /* phy_addr populated by the phy_init function */
+ u8 phy_addr;
+ /*u8 reserved1;*/
+
u32 lane_config;
u32 ext_phy_config;
-#define XGXS_EXT_PHY_TYPE(ext_phy_config) (ext_phy_config & \
- PORT_HW_CFG_XGXS_EXT_PHY_TYPE_MASK)
-#define SERDES_EXT_PHY_TYPE(ext_phy_config) (ext_phy_config & \
- PORT_HW_CFG_SERDES_EXT_PHY_TYPE_MASK)
+#define XGXS_EXT_PHY_TYPE(ext_phy_config) \
+ ((ext_phy_config) & PORT_HW_CFG_XGXS_EXT_PHY_TYPE_MASK)
+#define XGXS_EXT_PHY_ADDR(ext_phy_config) \
+ (((ext_phy_config) & PORT_HW_CFG_XGXS_EXT_PHY_ADDR_MASK) >> \
+ PORT_HW_CFG_XGXS_EXT_PHY_ADDR_SHIFT)
+#define SERDES_EXT_PHY_TYPE(ext_phy_config) \
+ ((ext_phy_config) & PORT_HW_CFG_SERDES_EXT_PHY_TYPE_MASK)
+
/* Phy register parameter */
u32 chip_id;
- /* phy_addr populated by the CLC */
- u8 phy_addr;
u16 xgxs_config_rx[4]; /* preemphasis values for the rx side */
-
u16 xgxs_config_tx[4]; /* preemphasis values for the tx side */
+
u32 feature_config_flags;
#define FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED (1<<0)
#define FEATURE_CONFIG_BC_SUPPORTS_OPT_MDL_VRFY (1<<2)
#define FEATURE_CONFIG_BCM8727_NOC (1<<3)
+
/* Device pointer passed to all callback functions */
struct bnx2x *bp;
};
/* Output parameters */
struct link_vars {
+ u8 phy_flags;
+
+ u8 mac_type;
+#define MAC_TYPE_NONE 0
+#define MAC_TYPE_EMAC 1
+#define MAC_TYPE_BMAC 2
+
u8 phy_link_up; /* internal phy link indication */
u8 link_up;
+
+ u16 line_speed;
u16 duplex;
+
u16 flow_ctrl;
- u32 ieee_fc;
- u8 mac_type;
+ u16 ieee_fc;
-#define MAC_TYPE_NONE 0
-#define MAC_TYPE_EMAC 1
-#define MAC_TYPE_BMAC 2
- u16 line_speed;
u32 autoneg;
#define AUTO_NEG_DISABLED 0x0
#define AUTO_NEG_ENABLED 0x1
#define AUTO_NEG_COMPLETE 0x2
-#define AUTO_NEG_PARALLEL_DETECTION_USED 0x3
-
- u8 phy_flags;
+#define AUTO_NEG_PARALLEL_DETECTION_USED 0x3
/* The same definitions as the shmem parameter */
u32 link_status;
Basically, the CLC takes care of the led for the link, but in case one needs
to set/unset the led unnaturally, set the "mode" to LED_MODE_OPER to
blink the led, and LED_MODE_OFF to set the led off.*/
-u8 bnx2x_set_led(struct bnx2x *bp, u8 port, u8 mode, u32 speed,
- u16 hw_led_mode, u32 chip_id);
+u8 bnx2x_set_led(struct link_params *params, u8 mode, u32 speed);
#define LED_MODE_OFF 0
#define LED_MODE_OPER 2
u8 bnx2x_override_led_value(struct bnx2x *bp, u8 port, u32 led_idx, u32 value);
-u8 bnx2x_flash_download(struct bnx2x *bp, u8 port, u32 ext_phy_config,
- u8 driver_loaded, char data[], u32 size);
/* bnx2x_handle_module_detect_int should be called upon module detection
interrupt */
void bnx2x_handle_module_detect_int(struct link_params *params);