-/* Copyright 2008 Broadcom Corporation
+/* Copyright 2008-2009 Broadcom Corporation
*
* Unless you and Broadcom execute a separate written software license
* agreement governing use of this software, this software is licensed to you
-#define FLOW_CTRL_AUTO PORT_FEATURE_FLOW_CONTROL_AUTO
-#define FLOW_CTRL_TX PORT_FEATURE_FLOW_CONTROL_TX
-#define FLOW_CTRL_RX PORT_FEATURE_FLOW_CONTROL_RX
-#define FLOW_CTRL_BOTH PORT_FEATURE_FLOW_CONTROL_BOTH
-#define FLOW_CTRL_NONE PORT_FEATURE_FLOW_CONTROL_NONE
+#define BNX2X_FLOW_CTRL_AUTO PORT_FEATURE_FLOW_CONTROL_AUTO
+#define BNX2X_FLOW_CTRL_TX PORT_FEATURE_FLOW_CONTROL_TX
+#define BNX2X_FLOW_CTRL_RX PORT_FEATURE_FLOW_CONTROL_RX
+#define BNX2X_FLOW_CTRL_BOTH PORT_FEATURE_FLOW_CONTROL_BOTH
+#define BNX2X_FLOW_CTRL_NONE PORT_FEATURE_FLOW_CONTROL_NONE
#define SPEED_AUTO_NEG 0
#define SPEED_12000 12000
#define LOOPBACK_BMAC 2
#define LOOPBACK_XGXS_10 3
#define LOOPBACK_EXT_PHY 4
+#define LOOPBACK_EXT 5
u16 req_duplex;
u16 req_flow_ctrl;
/* Device parameters */
u8 mac_addr[6];
-
-
/* shmem parameters */
u32 shmem_base;
u32 speed_cap_mask;
#define SWITCH_CFG_AUTO_DETECT PORT_FEATURE_CON_SWITCH_AUTO_DETECT
u16 hw_led_mode; /* part of the hw_config read from the shmem */
- u32 serdes_config;
u32 lane_config;
u32 ext_phy_config;
#define XGXS_EXT_PHY_TYPE(ext_phy_config) (ext_phy_config & \
/* phy_addr populated by the CLC */
u8 phy_addr;
+ u16 xgxs_config_rx[4]; /* preemphasis values for the rx side */
+
+ u16 xgxs_config_tx[4]; /* preemphasis values for the tx side */
+ u32 feature_config_flags;
+#define FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED (1<<0)
+#define FEATURE_CONFIG_MODULE_ENFORCMENT_ENABLED (2<<0)
/* Device pointer passed to all callback functions */
struct bnx2x *bp;
};
/* Initialize the phy */
u8 bnx2x_phy_init(struct link_params *input, struct link_vars *output);
-/* Reset the link. Should be called when driver or interface goes down */
-u8 bnx2x_link_reset(struct link_params *params, struct link_vars *vars);
+/* Reset the link. Should be called when driver or interface goes down
+ Before calling phy firmware upgrade, the reset_ext_phy should be set
+ to 0 */
+u8 bnx2x_link_reset(struct link_params *params, struct link_vars *vars,
+ u8 reset_ext_phy);
/* bnx2x_link_update should be called upon link interrupt */
u8 bnx2x_link_update(struct link_params *input, struct link_vars *output);
u8 phy_addr, u8 devad, u16 reg, u16 val);
/* Reads the link_status from the shmem,
- and update the link vars accordinaly */
+ and update the link vars accordingly */
void bnx2x_link_status_update(struct link_params *input,
struct link_vars *output);
/* returns string representing the fw_version of the external phy */
/* Set/Unset the led
Basically, the CLC takes care of the led for the link, but in case one needs
- to set/unset the led unnatually, set the "mode" to LED_MODE_OPER to
+ to set/unset the led unnaturally, set the "mode" to LED_MODE_OPER to
blink the led, and LED_MODE_OFF to set the led off.*/
u8 bnx2x_set_led(struct bnx2x *bp, u8 port, u8 mode, u32 speed,
u16 hw_led_mode, u32 chip_id);
u8 bnx2x_flash_download(struct bnx2x *bp, u8 port, u32 ext_phy_config,
u8 driver_loaded, char data[], u32 size);
+/* bnx2x_handle_module_detect_int should be called upon module detection
+ interrupt */
+void bnx2x_handle_module_detect_int(struct link_params *params);
+
/* Get the actual link status. In case it returns 0, link is up,
otherwise link is down*/
u8 bnx2x_test_link(struct link_params *input, struct link_vars *vars);
+/* One-time initialization for external phy after power up */
+u8 bnx2x_common_init_phy(struct bnx2x *bp, u32 shmem_base);
+
#endif /* BNX2X_LINK_H */