#include <asm/dma.h>
#include <linux/dma-mapping.h>
+#include <asm/div64.h>
+#include <asm/dpmc.h>
#include <asm/blackfin.h>
#include <asm/cacheflush.h>
#include <asm/portmux.h>
static u16 pin_req[] = P_MII0;
#endif
-static void bfin_mac_disable(void);
-static void bfin_mac_enable(void);
-
static void desc_list_free(void)
{
struct net_dma_desc_rx *r;
struct dma_descriptor *b = &(r->desc_b);
/* allocate a new skb for next time receive */
- new_skb = dev_alloc_skb(PKT_BUF_SZ + 2);
+ new_skb = dev_alloc_skb(PKT_BUF_SZ + NET_IP_ALIGN);
if (!new_skb) {
printk(KERN_NOTICE DRV_NAME
": init: low on mem - packet dropped\n");
goto init_error;
}
- skb_reserve(new_skb, 2);
+ skb_reserve(new_skb, NET_IP_ALIGN);
+ /* Invidate the data cache of skb->data range when it is write back
+ * cache. It will prevent overwritting the new data from DMA
+ */
+ blackfin_dcache_invalidate_range((unsigned long)new_skb->head,
+ (unsigned long)new_skb->end);
r->skb = new_skb;
/*
* MII operations
*/
/* Wait until the previous MDC/MDIO transaction has completed */
-static void mdio_poll(void)
+static int bfin_mdio_poll(void)
{
int timeout_cnt = MAX_TIMEOUT_CNT;
if (timeout_cnt-- < 0) {
printk(KERN_ERR DRV_NAME
": wait MDC/MDIO transaction to complete timeout\n");
- break;
+ return -ETIMEDOUT;
}
}
+
+ return 0;
}
/* Read an off-chip register in a PHY through the MDC/MDIO port */
-static int mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum)
+static int bfin_mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum)
{
- mdio_poll();
+ int ret;
+
+ ret = bfin_mdio_poll();
+ if (ret)
+ return ret;
/* read mode */
bfin_write_EMAC_STAADD(SET_PHYAD((u16) phy_addr) |
SET_REGAD((u16) regnum) |
STABUSY);
- mdio_poll();
+ ret = bfin_mdio_poll();
+ if (ret)
+ return ret;
return (int) bfin_read_EMAC_STADAT();
}
/* Write an off-chip register in a PHY through the MDC/MDIO port */
-static int mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum,
- u16 value)
+static int bfin_mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum,
+ u16 value)
{
- mdio_poll();
+ int ret;
+
+ ret = bfin_mdio_poll();
+ if (ret)
+ return ret;
bfin_write_EMAC_STADAT((u32) value);
STAOP |
STABUSY);
- mdio_poll();
-
- return 0;
+ return bfin_mdio_poll();
}
-static int mdiobus_reset(struct mii_bus *bus)
+static int bfin_mdiobus_reset(struct mii_bus *bus)
{
return 0;
}
u32 sclk, mdc_div;
/* Enable PHY output early */
- if (!(bfin_read_VR_CTL() & PHYCLKOE))
- bfin_write_VR_CTL(bfin_read_VR_CTL() | PHYCLKOE);
+ if (!(bfin_read_VR_CTL() & CLKBUFOE))
+ bfin_write_VR_CTL(bfin_read_VR_CTL() | CLKBUFOE);
sclk = get_sclk();
mdc_div = ((sclk / MDC_CLK) / 2) - 1;
/* search for connect PHY device */
for (i = 0; i < PHY_MAX_ADDR; i++) {
- struct phy_device *const tmp_phydev = lp->mii_bus.phy_map[i];
+ struct phy_device *const tmp_phydev = lp->mii_bus->phy_map[i];
if (!tmp_phydev)
continue; /* no PHY here... */
}
#if defined(CONFIG_BFIN_MAC_RMII)
- phydev = phy_connect(dev, phydev->dev.bus_id, &bfin_mac_adjust_link, 0,
- PHY_INTERFACE_MODE_RMII);
+ phydev = phy_connect(dev, dev_name(&phydev->dev), &bfin_mac_adjust_link,
+ 0, PHY_INTERFACE_MODE_RMII);
#else
- phydev = phy_connect(dev, phydev->dev.bus_id, &bfin_mac_adjust_link, 0,
- PHY_INTERFACE_MODE_MII);
+ phydev = phy_connect(dev, dev_name(&phydev->dev), &bfin_mac_adjust_link,
+ 0, PHY_INTERFACE_MODE_MII);
#endif
if (IS_ERR(phydev)) {
printk(KERN_INFO "%s: attached PHY driver [%s] "
"(mii_bus:phy_addr=%s, irq=%d, mdc_clk=%dHz(mdc_div=%d)"
"@sclk=%dMHz)\n",
- DRV_NAME, phydev->drv->name, phydev->dev.bus_id, phydev->irq,
+ DRV_NAME, phydev->drv->name, dev_name(&phydev->dev), phydev->irq,
MDC_CLK, mdc_div, sclk/1000000);
return 0;
* Ethtool support
*/
+/*
+ * interrupt routine for magic packet wakeup
+ */
+static irqreturn_t bfin_mac_wake_interrupt(int irq, void *dev_id)
+{
+ return IRQ_HANDLED;
+}
+
static int
bfin_mac_ethtool_getsettings(struct net_device *dev, struct ethtool_cmd *cmd)
{
strcpy(info->driver, DRV_NAME);
strcpy(info->version, DRV_VERSION);
strcpy(info->fw_version, "N/A");
- strcpy(info->bus_info, dev->dev.bus_id);
+ strcpy(info->bus_info, dev_name(&dev->dev));
+}
+
+static void bfin_mac_ethtool_getwol(struct net_device *dev,
+ struct ethtool_wolinfo *wolinfo)
+{
+ struct bfin_mac_local *lp = netdev_priv(dev);
+
+ wolinfo->supported = WAKE_MAGIC;
+ wolinfo->wolopts = lp->wol;
}
-static struct ethtool_ops bfin_mac_ethtool_ops = {
+static int bfin_mac_ethtool_setwol(struct net_device *dev,
+ struct ethtool_wolinfo *wolinfo)
+{
+ struct bfin_mac_local *lp = netdev_priv(dev);
+ int rc;
+
+ if (wolinfo->wolopts & (WAKE_MAGICSECURE |
+ WAKE_UCAST |
+ WAKE_MCAST |
+ WAKE_BCAST |
+ WAKE_ARP))
+ return -EOPNOTSUPP;
+
+ lp->wol = wolinfo->wolopts;
+
+ if (lp->wol && !lp->irq_wake_requested) {
+ /* register wake irq handler */
+ rc = request_irq(IRQ_MAC_WAKEDET, bfin_mac_wake_interrupt,
+ IRQF_DISABLED, "EMAC_WAKE", dev);
+ if (rc)
+ return rc;
+ lp->irq_wake_requested = true;
+ }
+
+ if (!lp->wol && lp->irq_wake_requested) {
+ free_irq(IRQ_MAC_WAKEDET, dev);
+ lp->irq_wake_requested = false;
+ }
+
+ /* Make sure the PHY driver doesn't suspend */
+ device_init_wakeup(&dev->dev, lp->wol);
+
+ return 0;
+}
+
+static const struct ethtool_ops bfin_mac_ethtool_ops = {
.get_settings = bfin_mac_ethtool_getsettings,
.set_settings = bfin_mac_ethtool_setsettings,
.get_link = ethtool_op_get_link,
.get_drvinfo = bfin_mac_ethtool_getdrvinfo,
+ .get_wol = bfin_mac_ethtool_getwol,
+ .set_wol = bfin_mac_ethtool_setwol,
};
/**************************************************************************/
* Configure checksum support and rcve frame word alignment
*/
sysctl = bfin_read_EMAC_SYSCTL();
+ sysctl |= RXDWA;
#if defined(BFIN_MAC_CSUM_OFFLOAD)
- sysctl |= RXDWA | RXCKS;
+ sysctl |= RXCKS;
#else
- sysctl |= RXDWA;
+ sysctl &= ~RXCKS;
#endif
bfin_write_EMAC_SYSCTL(sysctl);
return 0;
}
+#ifdef CONFIG_BFIN_MAC_USE_HWSTAMP
+#define bfin_mac_hwtstamp_is_none(cfg) ((cfg) == HWTSTAMP_FILTER_NONE)
+
+static int bfin_mac_hwtstamp_ioctl(struct net_device *netdev,
+ struct ifreq *ifr, int cmd)
+{
+ struct hwtstamp_config config;
+ struct bfin_mac_local *lp = netdev_priv(netdev);
+ u16 ptpctl;
+ u32 ptpfv1, ptpfv2, ptpfv3, ptpfoff;
+
+ if (copy_from_user(&config, ifr->ifr_data, sizeof(config)))
+ return -EFAULT;
+
+ pr_debug("%s config flag:0x%x, tx_type:0x%x, rx_filter:0x%x\n",
+ __func__, config.flags, config.tx_type, config.rx_filter);
+
+ /* reserved for future extensions */
+ if (config.flags)
+ return -EINVAL;
+
+ if ((config.tx_type != HWTSTAMP_TX_OFF) &&
+ (config.tx_type != HWTSTAMP_TX_ON))
+ return -ERANGE;
+
+ ptpctl = bfin_read_EMAC_PTP_CTL();
+
+ switch (config.rx_filter) {
+ case HWTSTAMP_FILTER_NONE:
+ /*
+ * Dont allow any timestamping
+ */
+ ptpfv3 = 0xFFFFFFFF;
+ bfin_write_EMAC_PTP_FV3(ptpfv3);
+ break;
+ case HWTSTAMP_FILTER_PTP_V1_L4_EVENT:
+ case HWTSTAMP_FILTER_PTP_V1_L4_SYNC:
+ case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ:
+ /*
+ * Clear the five comparison mask bits (bits[12:8]) in EMAC_PTP_CTL)
+ * to enable all the field matches.
+ */
+ ptpctl &= ~0x1F00;
+ bfin_write_EMAC_PTP_CTL(ptpctl);
+ /*
+ * Keep the default values of the EMAC_PTP_FOFF register.
+ */
+ ptpfoff = 0x4A24170C;
+ bfin_write_EMAC_PTP_FOFF(ptpfoff);
+ /*
+ * Keep the default values of the EMAC_PTP_FV1 and EMAC_PTP_FV2
+ * registers.
+ */
+ ptpfv1 = 0x11040800;
+ bfin_write_EMAC_PTP_FV1(ptpfv1);
+ ptpfv2 = 0x0140013F;
+ bfin_write_EMAC_PTP_FV2(ptpfv2);
+ /*
+ * The default value (0xFFFC) allows the timestamping of both
+ * received Sync messages and Delay_Req messages.
+ */
+ ptpfv3 = 0xFFFFFFFC;
+ bfin_write_EMAC_PTP_FV3(ptpfv3);
+
+ config.rx_filter = HWTSTAMP_FILTER_PTP_V1_L4_EVENT;
+ break;
+ case HWTSTAMP_FILTER_PTP_V2_L4_EVENT:
+ case HWTSTAMP_FILTER_PTP_V2_L4_SYNC:
+ case HWTSTAMP_FILTER_PTP_V2_DELAY_REQ:
+ /* Clear all five comparison mask bits (bits[12:8]) in the
+ * EMAC_PTP_CTL register to enable all the field matches.
+ */
+ ptpctl &= ~0x1F00;
+ bfin_write_EMAC_PTP_CTL(ptpctl);
+ /*
+ * Keep the default values of the EMAC_PTP_FOFF register, except set
+ * the PTPCOF field to 0x2A.
+ */
+ ptpfoff = 0x2A24170C;
+ bfin_write_EMAC_PTP_FOFF(ptpfoff);
+ /*
+ * Keep the default values of the EMAC_PTP_FV1 and EMAC_PTP_FV2
+ * registers.
+ */
+ ptpfv1 = 0x11040800;
+ bfin_write_EMAC_PTP_FV1(ptpfv1);
+ ptpfv2 = 0x0140013F;
+ bfin_write_EMAC_PTP_FV2(ptpfv2);
+ /*
+ * To allow the timestamping of Pdelay_Req and Pdelay_Resp, set
+ * the value to 0xFFF0.
+ */
+ ptpfv3 = 0xFFFFFFF0;
+ bfin_write_EMAC_PTP_FV3(ptpfv3);
+
+ config.rx_filter = HWTSTAMP_FILTER_PTP_V2_L4_EVENT;
+ break;
+ case HWTSTAMP_FILTER_PTP_V2_L2_EVENT:
+ case HWTSTAMP_FILTER_PTP_V2_L2_SYNC:
+ case HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ:
+ /*
+ * Clear bits 8 and 12 of the EMAC_PTP_CTL register to enable only the
+ * EFTM and PTPCM field comparison.
+ */
+ ptpctl &= ~0x1100;
+ bfin_write_EMAC_PTP_CTL(ptpctl);
+ /*
+ * Keep the default values of all the fields of the EMAC_PTP_FOFF
+ * register, except set the PTPCOF field to 0x0E.
+ */
+ ptpfoff = 0x0E24170C;
+ bfin_write_EMAC_PTP_FOFF(ptpfoff);
+ /*
+ * Program bits [15:0] of the EMAC_PTP_FV1 register to 0x88F7, which
+ * corresponds to PTP messages on the MAC layer.
+ */
+ ptpfv1 = 0x110488F7;
+ bfin_write_EMAC_PTP_FV1(ptpfv1);
+ ptpfv2 = 0x0140013F;
+ bfin_write_EMAC_PTP_FV2(ptpfv2);
+ /*
+ * To allow the timestamping of Pdelay_Req and Pdelay_Resp
+ * messages, set the value to 0xFFF0.
+ */
+ ptpfv3 = 0xFFFFFFF0;
+ bfin_write_EMAC_PTP_FV3(ptpfv3);
+
+ config.rx_filter = HWTSTAMP_FILTER_PTP_V2_L2_EVENT;
+ break;
+ default:
+ return -ERANGE;
+ }
+
+ if (config.tx_type == HWTSTAMP_TX_OFF &&
+ bfin_mac_hwtstamp_is_none(config.rx_filter)) {
+ ptpctl &= ~PTP_EN;
+ bfin_write_EMAC_PTP_CTL(ptpctl);
+
+ SSYNC();
+ } else {
+ ptpctl |= PTP_EN;
+ bfin_write_EMAC_PTP_CTL(ptpctl);
+
+ /*
+ * clear any existing timestamp
+ */
+ bfin_read_EMAC_PTP_RXSNAPLO();
+ bfin_read_EMAC_PTP_RXSNAPHI();
+
+ bfin_read_EMAC_PTP_TXSNAPLO();
+ bfin_read_EMAC_PTP_TXSNAPHI();
+
+ /*
+ * Set registers so that rollover occurs soon to test this.
+ */
+ bfin_write_EMAC_PTP_TIMELO(0x00000000);
+ bfin_write_EMAC_PTP_TIMEHI(0xFF800000);
+
+ SSYNC();
+
+ lp->compare.last_update = 0;
+ timecounter_init(&lp->clock,
+ &lp->cycles,
+ ktime_to_ns(ktime_get_real()));
+ timecompare_update(&lp->compare, 0);
+ }
+
+ lp->stamp_cfg = config;
+ return copy_to_user(ifr->ifr_data, &config, sizeof(config)) ?
+ -EFAULT : 0;
+}
+
+static void bfin_dump_hwtamp(char *s, ktime_t *hw, ktime_t *ts, struct timecompare *cmp)
+{
+ ktime_t sys = ktime_get_real();
+
+ pr_debug("%s %s hardware:%d,%d transform system:%d,%d system:%d,%d, cmp:%lld, %lld\n",
+ __func__, s, hw->tv.sec, hw->tv.nsec, ts->tv.sec, ts->tv.nsec, sys.tv.sec,
+ sys.tv.nsec, cmp->offset, cmp->skew);
+}
+
+static void bfin_tx_hwtstamp(struct net_device *netdev, struct sk_buff *skb)
+{
+ struct bfin_mac_local *lp = netdev_priv(netdev);
+ union skb_shared_tx *shtx = skb_tx(skb);
+
+ if (shtx->hardware) {
+ int timeout_cnt = MAX_TIMEOUT_CNT;
+
+ /* When doing time stamping, keep the connection to the socket
+ * a while longer
+ */
+ shtx->in_progress = 1;
+
+ /*
+ * The timestamping is done at the EMAC module's MII/RMII interface
+ * when the module sees the Start of Frame of an event message packet. This
+ * interface is the closest possible place to the physical Ethernet transmission
+ * medium, providing the best timing accuracy.
+ */
+ while ((!(bfin_read_EMAC_PTP_ISTAT() & TXTL)) && (--timeout_cnt))
+ udelay(1);
+ if (timeout_cnt == 0)
+ printk(KERN_ERR DRV_NAME
+ ": fails to timestamp the TX packet\n");
+ else {
+ struct skb_shared_hwtstamps shhwtstamps;
+ u64 ns;
+ u64 regval;
+
+ regval = bfin_read_EMAC_PTP_TXSNAPLO();
+ regval |= (u64)bfin_read_EMAC_PTP_TXSNAPHI() << 32;
+ memset(&shhwtstamps, 0, sizeof(shhwtstamps));
+ ns = timecounter_cyc2time(&lp->clock,
+ regval);
+ timecompare_update(&lp->compare, ns);
+ shhwtstamps.hwtstamp = ns_to_ktime(ns);
+ shhwtstamps.syststamp =
+ timecompare_transform(&lp->compare, ns);
+ skb_tstamp_tx(skb, &shhwtstamps);
+
+ bfin_dump_hwtamp("TX", &shhwtstamps.hwtstamp, &shhwtstamps.syststamp, &lp->compare);
+ }
+ }
+}
+
+static void bfin_rx_hwtstamp(struct net_device *netdev, struct sk_buff *skb)
+{
+ struct bfin_mac_local *lp = netdev_priv(netdev);
+ u32 valid;
+ u64 regval, ns;
+ struct skb_shared_hwtstamps *shhwtstamps;
+
+ if (bfin_mac_hwtstamp_is_none(lp->stamp_cfg.rx_filter))
+ return;
+
+ valid = bfin_read_EMAC_PTP_ISTAT() & RXEL;
+ if (!valid)
+ return;
+
+ shhwtstamps = skb_hwtstamps(skb);
+
+ regval = bfin_read_EMAC_PTP_RXSNAPLO();
+ regval |= (u64)bfin_read_EMAC_PTP_RXSNAPHI() << 32;
+ ns = timecounter_cyc2time(&lp->clock, regval);
+ timecompare_update(&lp->compare, ns);
+ memset(shhwtstamps, 0, sizeof(*shhwtstamps));
+ shhwtstamps->hwtstamp = ns_to_ktime(ns);
+ shhwtstamps->syststamp = timecompare_transform(&lp->compare, ns);
+
+ bfin_dump_hwtamp("RX", &shhwtstamps->hwtstamp, &shhwtstamps->syststamp, &lp->compare);
+}
+
+/*
+ * bfin_read_clock - read raw cycle counter (to be used by time counter)
+ */
+static cycle_t bfin_read_clock(const struct cyclecounter *tc)
+{
+ u64 stamp;
+
+ stamp = bfin_read_EMAC_PTP_TIMELO();
+ stamp |= (u64)bfin_read_EMAC_PTP_TIMEHI() << 32ULL;
+
+ return stamp;
+}
+
+#define PTP_CLK 25000000
+
+static void bfin_mac_hwtstamp_init(struct net_device *netdev)
+{
+ struct bfin_mac_local *lp = netdev_priv(netdev);
+ u64 append;
+
+ /* Initialize hardware timer */
+ append = PTP_CLK * (1ULL << 32);
+ do_div(append, get_sclk());
+ bfin_write_EMAC_PTP_ADDEND((u32)append);
+
+ memset(&lp->cycles, 0, sizeof(lp->cycles));
+ lp->cycles.read = bfin_read_clock;
+ lp->cycles.mask = CLOCKSOURCE_MASK(64);
+ lp->cycles.mult = 1000000000 / PTP_CLK;
+ lp->cycles.shift = 0;
+
+ /* Synchronize our NIC clock against system wall clock */
+ memset(&lp->compare, 0, sizeof(lp->compare));
+ lp->compare.source = &lp->clock;
+ lp->compare.target = ktime_get_real;
+ lp->compare.num_samples = 10;
+
+ /* Initialize hwstamp config */
+ lp->stamp_cfg.rx_filter = HWTSTAMP_FILTER_NONE;
+ lp->stamp_cfg.tx_type = HWTSTAMP_TX_OFF;
+}
+
+#else
+# define bfin_mac_hwtstamp_is_none(cfg) 0
+# define bfin_mac_hwtstamp_init(dev)
+# define bfin_mac_hwtstamp_ioctl(dev, ifr, cmd) (-EOPNOTSUPP)
+# define bfin_rx_hwtstamp(dev, skb)
+# define bfin_tx_hwtstamp(dev, skb)
+#endif
+
static void adjust_tx_list(void)
{
int timeout_cnt = MAX_TIMEOUT_CNT;
- if (tx_list_head->status.status_word != 0
- && current_tx_ptr != tx_list_head) {
+ if (tx_list_head->status.status_word != 0 &&
+ current_tx_ptr != tx_list_head) {
goto adjust_head; /* released something, just return; */
}
*/
if (current_tx_ptr->next->next == tx_list_head) {
while (tx_list_head->status.status_word == 0) {
- mdelay(1);
- if (tx_list_head->status.status_word != 0
- || !(bfin_read_DMA2_IRQ_STATUS() & 0x08)) {
+ udelay(10);
+ if (tx_list_head->status.status_word != 0 ||
+ !(bfin_read_DMA2_IRQ_STATUS() & DMA_RUN)) {
goto adjust_head;
}
if (timeout_cnt-- < 0) {
": no sk_buff in a transmitted frame!\n");
}
tx_list_head = tx_list_head->next;
- } while (tx_list_head->status.status_word != 0
- && current_tx_ptr != tx_list_head);
+ } while (tx_list_head->status.status_word != 0 &&
+ current_tx_ptr != tx_list_head);
return;
}
static int bfin_mac_hard_start_xmit(struct sk_buff *skb,
struct net_device *dev)
{
- unsigned int data;
+ u16 *data;
+ u32 data_align = (unsigned long)(skb->data) & 0x3;
+ union skb_shared_tx *shtx = skb_tx(skb);
current_tx_ptr->skb = skb;
- /*
- * Is skb->data always 16-bit aligned?
- * Do we need to memcpy((char *)(tail->packet + 2), skb->data, len)?
- */
- if ((((unsigned int)(skb->data)) & 0x02) == 2) {
+ if (data_align == 0x2) {
/* move skb->data to current_tx_ptr payload */
- data = (unsigned int)(skb->data) - 2;
- *((unsigned short *)data) = (unsigned short)(skb->len);
- current_tx_ptr->desc_a.start_addr = (unsigned long)data;
- /* this is important! */
- blackfin_dcache_flush_range(data, (data + (skb->len)) + 2);
+ data = (u16 *)(skb->data) - 1;
+ *data = (u16)(skb->len);
+ /*
+ * When transmitting an Ethernet packet, the PTP_TSYNC module requires
+ * a DMA_Length_Word field associated with the packet. The lower 12 bits
+ * of this field are the length of the packet payload in bytes and the higher
+ * 4 bits are the timestamping enable field.
+ */
+ if (shtx->hardware)
+ *data |= 0x1000;
+ current_tx_ptr->desc_a.start_addr = (u32)data;
+ /* this is important! */
+ blackfin_dcache_flush_range((u32)data,
+ (u32)((u8 *)data + skb->len + 4));
} else {
- *((unsigned short *)(current_tx_ptr->packet)) =
- (unsigned short)(skb->len);
- memcpy((char *)(current_tx_ptr->packet + 2), skb->data,
- (skb->len));
+ *((u16 *)(current_tx_ptr->packet)) = (u16)(skb->len);
+ /* enable timestamping for the sent packet */
+ if (shtx->hardware)
+ *((u16 *)(current_tx_ptr->packet)) |= 0x1000;
+ memcpy((u8 *)(current_tx_ptr->packet + 2), skb->data,
+ skb->len);
current_tx_ptr->desc_a.start_addr =
- (unsigned long)current_tx_ptr->packet;
+ (u32)current_tx_ptr->packet;
if (current_tx_ptr->status.status_word != 0)
current_tx_ptr->status.status_word = 0;
- blackfin_dcache_flush_range((unsigned int)current_tx_ptr->
- packet,
- (unsigned int)(current_tx_ptr->
- packet + skb->len) +
- 2);
+ blackfin_dcache_flush_range(
+ (u32)current_tx_ptr->packet,
+ (u32)(current_tx_ptr->packet + skb->len + 2));
}
+ /* make sure the internal data buffers in the core are drained
+ * so that the DMA descriptors are completely written when the
+ * DMA engine goes to fetch them below
+ */
+ SSYNC();
+
/* enable this packet's dma */
current_tx_ptr->desc_a.config |= DMAEN;
/* tx dma is running, just return */
- if (bfin_read_DMA2_IRQ_STATUS() & 0x08)
+ if (bfin_read_DMA2_IRQ_STATUS() & DMA_RUN)
goto out;
/* tx dma is not running */
out:
adjust_tx_list();
+
+ bfin_tx_hwtstamp(dev, skb);
+
current_tx_ptr = current_tx_ptr->next;
- dev->trans_start = jiffies;
dev->stats.tx_packets++;
dev->stats.tx_bytes += (skb->len);
- return 0;
+ return NETDEV_TX_OK;
}
+#define IP_HEADER_OFF 0
+#define RX_ERROR_MASK (RX_LONG | RX_ALIGN | RX_CRC | RX_LEN | \
+ RX_FRAG | RX_ADDR | RX_DMAO | RX_PHY | RX_LATE | RX_RANGE)
+
static void bfin_mac_rx(struct net_device *dev)
{
struct sk_buff *skb, *new_skb;
unsigned short len;
+ struct bfin_mac_local *lp __maybe_unused = netdev_priv(dev);
+#if defined(BFIN_MAC_CSUM_OFFLOAD)
+ unsigned int i;
+ unsigned char fcs[ETH_FCS_LEN + 1];
+#endif
+
+ /* check if frame status word reports an error condition
+ * we which case we simply drop the packet
+ */
+ if (current_rx_ptr->status.status_word & RX_ERROR_MASK) {
+ printk(KERN_NOTICE DRV_NAME
+ ": rx: receive error - packet dropped\n");
+ dev->stats.rx_dropped++;
+ goto out;
+ }
/* allocate a new skb for next time receive */
skb = current_rx_ptr->skb;
- new_skb = dev_alloc_skb(PKT_BUF_SZ + 2);
+
+ new_skb = dev_alloc_skb(PKT_BUF_SZ + NET_IP_ALIGN);
if (!new_skb) {
printk(KERN_NOTICE DRV_NAME
": rx: low on mem - packet dropped\n");
goto out;
}
/* reserve 2 bytes for RXDWA padding */
- skb_reserve(new_skb, 2);
- current_rx_ptr->skb = new_skb;
- current_rx_ptr->desc_a.start_addr = (unsigned long)new_skb->data - 2;
-
+ skb_reserve(new_skb, NET_IP_ALIGN);
/* Invidate the data cache of skb->data range when it is write back
* cache. It will prevent overwritting the new data from DMA
*/
blackfin_dcache_invalidate_range((unsigned long)new_skb->head,
(unsigned long)new_skb->end);
+ current_rx_ptr->skb = new_skb;
+ current_rx_ptr->desc_a.start_addr = (unsigned long)new_skb->data - 2;
+
len = (unsigned short)((current_rx_ptr->status.status_word) & RX_FRLEN);
+ /* Deduce Ethernet FCS length from Ethernet payload length */
+ len -= ETH_FCS_LEN;
skb_put(skb, len);
- blackfin_dcache_invalidate_range((unsigned long)skb->head,
- (unsigned long)skb->tail);
- dev->last_rx = jiffies;
- skb->dev = dev;
skb->protocol = eth_type_trans(skb, dev);
+
+ bfin_rx_hwtstamp(dev, skb);
+
#if defined(BFIN_MAC_CSUM_OFFLOAD)
- skb->csum = current_rx_ptr->status.ip_payload_csum;
- skb->ip_summed = CHECKSUM_COMPLETE;
+ /* Checksum offloading only works for IPv4 packets with the standard IP header
+ * length of 20 bytes, because the blackfin MAC checksum calculation is
+ * based on that assumption. We must NOT use the calculated checksum if our
+ * IP version or header break that assumption.
+ */
+ if (skb->data[IP_HEADER_OFF] == 0x45) {
+ skb->csum = current_rx_ptr->status.ip_payload_csum;
+ /*
+ * Deduce Ethernet FCS from hardware generated IP payload checksum.
+ * IP checksum is based on 16-bit one's complement algorithm.
+ * To deduce a value from checksum is equal to add its inversion.
+ * If the IP payload len is odd, the inversed FCS should also
+ * begin from odd address and leave first byte zero.
+ */
+ if (skb->len % 2) {
+ fcs[0] = 0;
+ for (i = 0; i < ETH_FCS_LEN; i++)
+ fcs[i + 1] = ~skb->data[skb->len + i];
+ skb->csum = csum_partial(fcs, ETH_FCS_LEN + 1, skb->csum);
+ } else {
+ for (i = 0; i < ETH_FCS_LEN; i++)
+ fcs[i] = ~skb->data[skb->len + i];
+ skb->csum = csum_partial(fcs, ETH_FCS_LEN, skb->csum);
+ }
+ skb->ip_summed = CHECKSUM_COMPLETE;
+ }
#endif
netif_rx(skb);
dev->stats.rx_packets++;
dev->stats.rx_bytes += len;
+out:
current_rx_ptr->status.status_word = 0x00000000;
current_rx_ptr = current_rx_ptr->next;
-
-out:
- return;
}
/* interrupt routine to handle rx and error signal */
/*
* Enable Interrupts, Receive, and Transmit
*/
-static void bfin_mac_enable(void)
+static int bfin_mac_enable(void)
{
+ int ret;
u32 opmode;
- pr_debug("%s: %s\n", DRV_NAME, __FUNCTION__);
+ pr_debug("%s: %s\n", DRV_NAME, __func__);
/* Set RX DMA */
bfin_write_DMA1_NEXT_DESC_PTR(&(rx_list_head->desc_a));
bfin_write_DMA1_CONFIG(rx_list_head->desc_a.config);
/* Wait MII done */
- mdio_poll();
+ ret = bfin_mdio_poll();
+ if (ret)
+ return ret;
/* We enable only RX here */
/* ASTP : Enable Automatic Pad Stripping
#endif
/* Turn on the EMAC rx */
bfin_write_EMAC_OPMODE(opmode);
+
+ return 0;
}
/* Our watchdog timed out. Called by the networking layer */
static void bfin_mac_timeout(struct net_device *dev)
{
- pr_debug("%s: %s\n", dev->name, __FUNCTION__);
+ pr_debug("%s: %s\n", dev->name, __func__);
bfin_mac_disable();
bfin_mac_enable();
/* We can accept TX packets again */
- dev->trans_start = jiffies;
+ dev->trans_start = jiffies; /* prevent tx timeout */
netif_wake_queue(dev);
}
static void bfin_mac_multicast_hash(struct net_device *dev)
{
u32 emac_hashhi, emac_hashlo;
- struct dev_mc_list *dmi = dev->mc_list;
+ struct netdev_hw_addr *ha;
char *addrs;
- int i;
u32 crc;
emac_hashhi = emac_hashlo = 0;
- for (i = 0; i < dev->mc_count; i++) {
- addrs = dmi->dmi_addr;
- dmi = dmi->next;
+ netdev_for_each_mc_addr(ha, dev) {
+ addrs = ha->addr;
/* skip non-multicast addresses */
if (!(*addrs & 1))
bfin_write_EMAC_HASHHI(emac_hashhi);
bfin_write_EMAC_HASHLO(emac_hashlo);
-
- return;
}
/*
if (dev->flags & IFF_PROMISC) {
printk(KERN_INFO "%s: set to promisc mode\n", dev->name);
sysctl = bfin_read_EMAC_OPMODE();
- sysctl |= RAF;
+ sysctl |= PR;
bfin_write_EMAC_OPMODE(sysctl);
} else if (dev->flags & IFF_ALLMULTI) {
/* accept all multicast */
sysctl = bfin_read_EMAC_OPMODE();
sysctl |= PAM;
bfin_write_EMAC_OPMODE(sysctl);
- } else if (dev->mc_count) {
+ } else if (!netdev_mc_empty(dev)) {
/* set up multicast hash table */
sysctl = bfin_read_EMAC_OPMODE();
sysctl |= HM;
}
}
+static int bfin_mac_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
+{
+ switch (cmd) {
+ case SIOCSHWTSTAMP:
+ return bfin_mac_hwtstamp_ioctl(netdev, ifr, cmd);
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
/*
* this puts the device in an inactive state
*/
static int bfin_mac_open(struct net_device *dev)
{
struct bfin_mac_local *lp = netdev_priv(dev);
- int retval;
- pr_debug("%s: %s\n", dev->name, __FUNCTION__);
+ int ret;
+ pr_debug("%s: %s\n", dev->name, __func__);
/*
* Check that the address is valid. If its not, refuse
}
/* initial rx and tx list */
- retval = desc_list_init();
-
- if (retval)
- return retval;
+ ret = desc_list_init();
+ if (ret)
+ return ret;
phy_start(lp->phydev);
phy_write(lp->phydev, MII_BMCR, BMCR_RESET);
setup_system_regs(dev);
+ setup_mac_addr(dev->dev_addr);
+
bfin_mac_disable();
- bfin_mac_enable();
+ ret = bfin_mac_enable();
+ if (ret)
+ return ret;
pr_debug("hardware init finished\n");
+
netif_start_queue(dev);
netif_carrier_on(dev);
}
/*
- *
* this makes the board clean up everything that it can
* and not talk to the outside world. Caused by
* an 'ifconfig ethX down'
static int bfin_mac_close(struct net_device *dev)
{
struct bfin_mac_local *lp = netdev_priv(dev);
- pr_debug("%s: %s\n", dev->name, __FUNCTION__);
+ pr_debug("%s: %s\n", dev->name, __func__);
netif_stop_queue(dev);
netif_carrier_off(dev);
return 0;
}
+static const struct net_device_ops bfin_mac_netdev_ops = {
+ .ndo_open = bfin_mac_open,
+ .ndo_stop = bfin_mac_close,
+ .ndo_start_xmit = bfin_mac_hard_start_xmit,
+ .ndo_set_mac_address = bfin_mac_set_mac_address,
+ .ndo_tx_timeout = bfin_mac_timeout,
+ .ndo_set_multicast_list = bfin_mac_set_multicast_list,
+ .ndo_do_ioctl = bfin_mac_ioctl,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_change_mtu = eth_change_mtu,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ .ndo_poll_controller = bfin_mac_poll,
+#endif
+};
+
static int __devinit bfin_mac_probe(struct platform_device *pdev)
{
struct net_device *ndev;
struct bfin_mac_local *lp;
- int rc, i;
+ struct platform_device *pd;
+ int rc;
ndev = alloc_etherdev(sizeof(struct bfin_mac_local));
if (!ndev) {
goto out_err_probe_mac;
}
- /* set the GPIO pins to Ethernet mode */
- rc = peripheral_request_list(pin_req, DRV_NAME);
- if (rc) {
- dev_err(&pdev->dev, "Requesting peripherals failed!\n");
- rc = -EFAULT;
- goto out_err_setup_pin_mux;
- }
/*
* Is it valid? (Did bootloader initialize it?)
setup_mac_addr(ndev->dev_addr);
- /* MDIO bus initial */
- lp->mii_bus.priv = ndev;
- lp->mii_bus.read = mdiobus_read;
- lp->mii_bus.write = mdiobus_write;
- lp->mii_bus.reset = mdiobus_reset;
- lp->mii_bus.name = "bfin_mac_mdio";
- snprintf(lp->mii_bus.id, MII_BUS_ID_SIZE, "0");
- lp->mii_bus.irq = kmalloc(sizeof(int)*PHY_MAX_ADDR, GFP_KERNEL);
- for (i = 0; i < PHY_MAX_ADDR; ++i)
- lp->mii_bus.irq[i] = PHY_POLL;
-
- rc = mdiobus_register(&lp->mii_bus);
- if (rc) {
- dev_err(&pdev->dev, "Cannot register MDIO bus!\n");
- goto out_err_mdiobus_register;
+ if (!pdev->dev.platform_data) {
+ dev_err(&pdev->dev, "Cannot get platform device bfin_mii_bus!\n");
+ rc = -ENODEV;
+ goto out_err_probe_mac;
+ }
+ pd = pdev->dev.platform_data;
+ lp->mii_bus = platform_get_drvdata(pd);
+ if (!lp->mii_bus) {
+ dev_err(&pdev->dev, "Cannot get mii_bus!\n");
+ rc = -ENODEV;
+ goto out_err_mii_bus_probe;
}
+ lp->mii_bus->priv = ndev;
rc = mii_probe(ndev);
if (rc) {
/* Fill in the fields of the device structure with ethernet values. */
ether_setup(ndev);
- ndev->open = bfin_mac_open;
- ndev->stop = bfin_mac_close;
- ndev->hard_start_xmit = bfin_mac_hard_start_xmit;
- ndev->set_mac_address = bfin_mac_set_mac_address;
- ndev->tx_timeout = bfin_mac_timeout;
- ndev->set_multicast_list = bfin_mac_set_multicast_list;
-#ifdef CONFIG_NET_POLL_CONTROLLER
- ndev->poll_controller = bfin_mac_poll;
-#endif
+ ndev->netdev_ops = &bfin_mac_netdev_ops;
ndev->ethtool_ops = &bfin_mac_ethtool_ops;
spin_lock_init(&lp->lock);
/* now, enable interrupts */
/* register irq handler */
rc = request_irq(IRQ_MAC_RX, bfin_mac_interrupt,
- IRQF_DISABLED | IRQF_SHARED, "EMAC_RX", ndev);
+ IRQF_DISABLED, "EMAC_RX", ndev);
if (rc) {
dev_err(&pdev->dev, "Cannot request Blackfin MAC RX IRQ!\n");
rc = -EBUSY;
goto out_err_reg_ndev;
}
+ bfin_mac_hwtstamp_init(ndev);
+
/* now, print out the card info, in a short format.. */
dev_info(&pdev->dev, "%s, Version %s\n", DRV_DESC, DRV_VERSION);
free_irq(IRQ_MAC_RX, ndev);
out_err_request_irq:
out_err_mii_probe:
- mdiobus_unregister(&lp->mii_bus);
-out_err_mdiobus_register:
+ mdiobus_unregister(lp->mii_bus);
+ mdiobus_free(lp->mii_bus);
+out_err_mii_bus_probe:
peripheral_free_list(pin_req);
-out_err_setup_pin_mux:
out_err_probe_mac:
platform_set_drvdata(pdev, NULL);
free_netdev(ndev);
platform_set_drvdata(pdev, NULL);
- mdiobus_unregister(&lp->mii_bus);
+ lp->mii_bus->priv = NULL;
unregister_netdev(ndev);
static int bfin_mac_suspend(struct platform_device *pdev, pm_message_t mesg)
{
struct net_device *net_dev = platform_get_drvdata(pdev);
+ struct bfin_mac_local *lp = netdev_priv(net_dev);
- if (netif_running(net_dev))
- bfin_mac_close(net_dev);
+ if (lp->wol) {
+ bfin_write_EMAC_OPMODE((bfin_read_EMAC_OPMODE() & ~TE) | RE);
+ bfin_write_EMAC_WKUP_CTL(MPKE);
+ enable_irq_wake(IRQ_MAC_WAKEDET);
+ } else {
+ if (netif_running(net_dev))
+ bfin_mac_close(net_dev);
+ }
return 0;
}
static int bfin_mac_resume(struct platform_device *pdev)
{
struct net_device *net_dev = platform_get_drvdata(pdev);
+ struct bfin_mac_local *lp = netdev_priv(net_dev);
- if (netif_running(net_dev))
- bfin_mac_open(net_dev);
+ if (lp->wol) {
+ bfin_write_EMAC_OPMODE(bfin_read_EMAC_OPMODE() | TE);
+ bfin_write_EMAC_WKUP_CTL(0);
+ disable_irq_wake(IRQ_MAC_WAKEDET);
+ } else {
+ if (netif_running(net_dev))
+ bfin_mac_open(net_dev);
+ }
return 0;
}
#define bfin_mac_resume NULL
#endif /* CONFIG_PM */
+static int __devinit bfin_mii_bus_probe(struct platform_device *pdev)
+{
+ struct mii_bus *miibus;
+ int rc, i;
+
+ /*
+ * We are setting up a network card,
+ * so set the GPIO pins to Ethernet mode
+ */
+ rc = peripheral_request_list(pin_req, DRV_NAME);
+ if (rc) {
+ dev_err(&pdev->dev, "Requesting peripherals failed!\n");
+ return rc;
+ }
+
+ rc = -ENOMEM;
+ miibus = mdiobus_alloc();
+ if (miibus == NULL)
+ goto out_err_alloc;
+ miibus->read = bfin_mdiobus_read;
+ miibus->write = bfin_mdiobus_write;
+ miibus->reset = bfin_mdiobus_reset;
+
+ miibus->parent = &pdev->dev;
+ miibus->name = "bfin_mii_bus";
+ snprintf(miibus->id, MII_BUS_ID_SIZE, "0");
+ miibus->irq = kmalloc(sizeof(int)*PHY_MAX_ADDR, GFP_KERNEL);
+ if (miibus->irq == NULL)
+ goto out_err_alloc;
+ for (i = 0; i < PHY_MAX_ADDR; ++i)
+ miibus->irq[i] = PHY_POLL;
+
+ rc = mdiobus_register(miibus);
+ if (rc) {
+ dev_err(&pdev->dev, "Cannot register MDIO bus!\n");
+ goto out_err_mdiobus_register;
+ }
+
+ platform_set_drvdata(pdev, miibus);
+ return 0;
+
+out_err_mdiobus_register:
+ mdiobus_free(miibus);
+out_err_alloc:
+ peripheral_free_list(pin_req);
+
+ return rc;
+}
+
+static int __devexit bfin_mii_bus_remove(struct platform_device *pdev)
+{
+ struct mii_bus *miibus = platform_get_drvdata(pdev);
+ platform_set_drvdata(pdev, NULL);
+ mdiobus_unregister(miibus);
+ mdiobus_free(miibus);
+ peripheral_free_list(pin_req);
+ return 0;
+}
+
+static struct platform_driver bfin_mii_bus_driver = {
+ .probe = bfin_mii_bus_probe,
+ .remove = __devexit_p(bfin_mii_bus_remove),
+ .driver = {
+ .name = "bfin_mii_bus",
+ .owner = THIS_MODULE,
+ },
+};
+
static struct platform_driver bfin_mac_driver = {
.probe = bfin_mac_probe,
.remove = __devexit_p(bfin_mac_remove),
static int __init bfin_mac_init(void)
{
- return platform_driver_register(&bfin_mac_driver);
+ int ret;
+ ret = platform_driver_register(&bfin_mii_bus_driver);
+ if (!ret)
+ return platform_driver_register(&bfin_mac_driver);
+ return -ENODEV;
}
module_init(bfin_mac_init);
static void __exit bfin_mac_cleanup(void)
{
platform_driver_unregister(&bfin_mac_driver);
+ platform_driver_unregister(&bfin_mii_bus_driver);
}
module_exit(bfin_mac_cleanup);
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff