menuconfig NETDEVICES
default y if UML
+ depends on NET
bool "Network device support"
---help---
You can say N here if you don't intend to connect your Linux box to
# that for each of the symbols.
if NETDEVICES
+config NETDEVICES_MULTIQUEUE
+ bool "Netdevice multiple hardware queue support"
+ ---help---
+ Say Y here if you want to allow the network stack to use multiple
+ hardware TX queues on an ethernet device.
+
+ Most people will say N here.
+
config IFB
tristate "Intermediate Functional Block support"
depends on NET_CLS_ACT
To compile this driver as a module, choose M here: the module
will be called bonding.
+config MACVLAN
+ tristate "MAC-VLAN support (EXPERIMENTAL)"
+ depends on EXPERIMENTAL
+ ---help---
+ This allows one to create virtual interfaces that map packets to
+ or from specific MAC addresses to a particular interface.
+
+ To compile this driver as a module, choose M here: the module
+ will be called macvlan.
+
config EQUALIZER
tristate "EQL (serial line load balancing) support"
---help---
config MACB
tristate "Atmel MACB support"
depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263
- select MII
+ select PHYLIB
help
The Atmel MACB ethernet interface is found on many AT32 and AT91
parts. Say Y to include support for the MACB chip.
on the AMD Lance chipset: RieblCard (with or without battery), or
PAMCard VME (also the version by Rhotron, with different addresses).
-config ATARI_BIONET
- tristate "BioNet-100 support"
- depends on ATARI && ATARI_ACSI && BROKEN
- help
- Say Y to include support for BioData's BioNet-100 Ethernet adapter
- for the ACSI port. The driver works (has to work...) with a polled
- I/O scheme, so it's rather slow :-(
-
-config ATARI_PAMSNET
- tristate "PAMsNet support"
- depends on ATARI && ATARI_ACSI && BROKEN
- help
- Say Y to include support for the PAMsNet Ethernet adapter for the
- ACSI port ("ACSI node"). The driver works (has to work...) with a
- polled I/O scheme, so it's rather slow :-(
-
config SUN3LANCE
tristate "Sun3/Sun3x on-board LANCE support"
depends on SUN3 || SUN3X
Support for the Sun Cassini chip, aka Sun GigaSwift Ethernet. See also
<http://www.sun.com/products-n-solutions/hardware/docs/pdf/817-4341-10.pdf>
+config SUNVNET
+ tristate "Sun Virtual Network support"
+ depends on SUN_LDOMS
+ help
+ Support for virtual network devices under Sun Logical Domains.
+
config NET_VENDOR_3COM
bool "3COM cards"
depends on ISA || EISA || MCA || PCI
<file:Documentation/networking/net-modules.txt>. The module
will be called smc-ultra32.
+config BFIN_MAC
+ tristate "Blackfin 536/537 on-chip mac support"
+ depends on NET_ETHERNET && (BF537 || BF536) && (!BF537_PORT_H)
+ select CRC32
+ select BFIN_MAC_USE_L1 if DMA_UNCACHED_NONE
+ help
+ This is the driver for blackfin on-chip mac device. Say Y if you want it
+ compiled into the kernel. This driver is also available as a module
+ ( = code which can be inserted in and removed from the running kernel
+ whenever you want). The module will be called bfin_mac.
+
+config BFIN_MAC_USE_L1
+ bool "Use L1 memory for rx/tx packets"
+ depends on BFIN_MAC && BF537
+ default y
+ help
+ To get maximum network performace, you should use L1 memory as rx/tx buffers.
+ Say N here if you want to reserve L1 memory for other uses.
+
+config BFIN_TX_DESC_NUM
+ int "Number of transmit buffer packets"
+ depends on BFIN_MAC
+ range 6 10 if BFIN_MAC_USE_L1
+ range 10 100
+ default "10"
+ help
+ Set the number of buffer packets used in driver.
+
+config BFIN_RX_DESC_NUM
+ int "Number of receive buffer packets"
+ depends on BFIN_MAC
+ range 20 100 if BFIN_MAC_USE_L1
+ range 20 800
+ default "20"
+ help
+ Set the number of buffer packets used in driver.
+
+config BFIN_MAC_RMII
+ bool "RMII PHY Interface (EXPERIMENTAL)"
+ depends on BFIN_MAC && EXPERIMENTAL
+ default n
+ help
+ Use Reduced PHY MII Interface
+
config SMC9194
tristate "SMC 9194 support"
depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN)
source "drivers/s390/net/Kconfig"
+config XEN_NETDEV_FRONTEND
+ tristate "Xen network device frontend driver"
+ depends on XEN
+ default y
+ help
+ The network device frontend driver allows the kernel to
+ access network devices exported exported by a virtual
+ machine containing a physical network device driver. The
+ frontend driver is intended for unprivileged guest domains;
+ if you are compiling a kernel for a Xen guest, you almost
+ certainly want to enable this.
+
config ISERIES_VETH
tristate "iSeries Virtual Ethernet driver support"
depends on PPC_ISERIES
which can lead to bad results if the ATM peer loses state and
changes its encapsulation unilaterally.
+config PPPOL2TP
+ tristate "PPP over L2TP (EXPERIMENTAL)"
+ depends on EXPERIMENTAL && PPP
+ help
+ Support for PPP-over-L2TP socket family. L2TP is a protocol
+ used by ISPs and enterprises to tunnel PPP traffic over UDP
+ tunnels. L2TP is replacing PPTP for VPN uses.
+
+ This kernel component handles only L2TP data packets: a
+ userland daemon handles L2TP the control protocol (tunnel
+ and session setup). One such daemon is OpenL2TP
+ (http://openl2tp.sourceforge.net/).
+
config SLIP
tristate "SLIP (serial line) support"
---help---
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff