# Network device configuration
#
+menu "Network device support"
+
config NETDEVICES
depends on NET
bool "Network device support"
If unsure, say Y.
+# All the following symbols are dependent on NETDEVICES - do not repeat
+# that for each of the symbols.
+if NETDEVICES
+
config DUMMY
tristate "Dummy net driver support"
- depends on NETDEVICES
---help---
This is essentially a bit-bucket device (i.e. traffic you send to
this device is consigned into oblivion) with a configurable IP
config BONDING
tristate "Bonding driver support"
- depends on NETDEVICES
depends on INET
---help---
Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
config EQUALIZER
tristate "EQL (serial line load balancing) support"
- depends on NETDEVICES
---help---
If you have two serial connections to some other computer (this
usually requires two modems and two telephone lines) and you use
config TUN
tristate "Universal TUN/TAP device driver support"
- depends on NETDEVICES
select CRC32
---help---
TUN/TAP provides packet reception and transmission for user space
config NET_SB1000
tristate "General Instruments Surfboard 1000"
- depends on NETDEVICES && PNP
+ depends on PNP
---help---
This is a driver for the General Instrument (also known as
NextLevel) SURFboard 1000 internal
If you don't have this card, of course say N.
-if NETDEVICES
source "drivers/net/arcnet/Kconfig"
-endif
+
+source "drivers/net/phy/Kconfig"
#
# Ethernet
#
menu "Ethernet (10 or 100Mbit)"
- depends on NETDEVICES && !UML
+ depends on !UML
config NET_ETHERNET
bool "Ethernet (10 or 100Mbit)"
If you're not building a kernel for a Sun 3, say N.
config SUN3_82586
- tristate "Sun3 on-board Intel 82586 support"
+ bool "Sun3 on-board Intel 82586 support"
depends on NET_ETHERNET && SUN3
help
This driver enables support for the on-board Intel 82586 based
the moment only acceleration of IPv4 is supported. This option
enables offloading for checksums on transmit. If unsure, say Y.
+config MIPS_SIM_NET
+ tristate "MIPS simulator Network device (EXPERIMENTAL)"
+ depends on NETDEVICES && MIPS_SIM && EXPERIMENTAL
+ help
+ The MIPSNET device is a simple Ethernet network device which is
+ emulated by the MIPS Simulator.
+ If you are not using a MIPSsim or are unsure, say N.
+
config SGI_O2MACE_ETH
tristate "SGI O2 MACE Fast Ethernet support"
depends on NET_ETHERNET && SGI_IP32=y
Support for the Sun GEM chip, aka Sun GigabitEthernet/P 2.0. See also
<http://www.sun.com/products-n-solutions/hardware/docs/pdf/806-3985-10.pdf>.
+config CASSINI
+ tristate "Sun Cassini support"
+ depends on NET_ETHERNET && PCI
+ select CRC32
+ help
+ Support for the Sun Cassini chip, aka Sun GigaSwift Ethernet. See also
+ <http://www.sun.com/products-n-solutions/hardware/docs/pdf/817-4341-10.pdf>
+
config NET_VENDOR_3COM
bool "3COM cards"
depends on NET_ETHERNET && (ISA || EISA || MCA || PCI)
config ELPLUS
tristate "3c505 \"EtherLink Plus\" support"
- depends on NET_VENDOR_3COM && ISA
+ depends on NET_VENDOR_3COM && ISA && ISA_DMA_API
---help---
Information about this network (Ethernet) card can be found in
<file:Documentation/networking/3c505.txt>. If you have a card of
config 3C515
tristate "3c515 ISA \"Fast EtherLink\""
- depends on NET_VENDOR_3COM && (ISA || EISA)
+ depends on NET_VENDOR_3COM && (ISA || EISA) && ISA_DMA_API
help
If you have a 3Com ISA EtherLink XL "Corkscrew" 3c515 Fast Ethernet
network card, say Y and read the Ethernet-HOWTO, available from
config LANCE
tristate "AMD LANCE and PCnet (AT1500 and NE2100) support"
- depends on NET_ETHERNET && ISA
+ depends on NET_ETHERNET && ISA && ISA_DMA_API
help
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
tristate "SMC 91C9x/91C1xxx support"
select CRC32
select MII
- depends on NET_ETHERNET && (ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH)
+ depends on NET_ETHERNET && (ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || SOC_AU1X00)
help
This is a driver for SMC's 91x series of Ethernet chipsets,
including the SMC91C94 and the SMC91C111. Say Y if you want it
<file:Documentation/networking/net-modules.txt>. The module
will be called smc9194.
+config DM9000
+ tristate "DM9000 support"
+ depends on ARM && NET_ETHERNET
+ select CRC32
+ select MII
+ ---help---
+ Support for DM9000 chipset.
+
+ To compile this driver as a module, choose M here and read
+ <file:Documentation/networking/net-modules.txt>. The module will be
+ called dm9000.
+
config NET_VENDOR_RACAL
bool "Racal-Interlan (Micom) NI cards"
depends on NET_ETHERNET && ISA
config NI65
tristate "NI6510 support"
- depends on NET_VENDOR_RACAL && ISA
+ depends on NET_VENDOR_RACAL && ISA && ISA_DMA_API
help
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
<file:Documentation/networking/net-modules.txt>. The module
will be called eepro.
-config FMV18X
- tristate "FMV-181/182/183/184 support (OBSOLETE)"
- depends on NET_ISA && OBSOLETE
- ---help---
- If you have a Fujitsu FMV-181/182/183/184 network (Ethernet) card,
- say Y and read the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- If you use an FMV-183 or FMV-184 and it is not working, you may need
- to disable Plug & Play mode of the card.
-
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
- will be called fmv18x.
-
config HPLAN_PLUS
tristate "HP PCLAN+ (27247B and 27252A) support"
depends on NET_ISA
config ZNET
tristate "Zenith Z-Note support (EXPERIMENTAL)"
- depends on NET_ISA && EXPERIMENTAL
+ depends on NET_ISA && EXPERIMENTAL && ISA_DMA_API
help
The Zenith Z-Note notebook computer has a built-in network
(Ethernet) card, and this is the Linux driver for it. Note that the
<file:Documentation/networking/net-modules.txt>. The module
will be called seeq8005.
-config SK_G16
- tristate "SK_G16 support (OBSOLETE)"
- depends on NET_ISA && OBSOLETE
- help
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
config SKMC
tristate "SKnet MCA support"
depends on NET_ETHERNET && MCA && BROKEN
config IBMVETH
tristate "IBM LAN Virtual Ethernet support"
- depends on NETDEVICES && NET_ETHERNET && PPC_PSERIES
+ depends on NET_ETHERNET && PPC_PSERIES
---help---
This driver supports virtual ethernet adapters on newer IBM iSeries
and pSeries systems.
be called ibmveth.
config IBM_EMAC
- tristate "IBM PPC4xx EMAC driver support"
+ tristate "PowerPC 4xx on-chip Ethernet support"
depends on 4xx
- select CRC32
- ---help---
- This driver supports the IBM PPC4xx EMAC family of on-chip
- Ethernet controllers.
-
-config IBM_EMAC_ERRMSG
- bool "Verbose error messages"
- depends on IBM_EMAC
+ help
+ This driver supports the PowerPC 4xx EMAC family of on-chip
+ Ethernet controllers.
config IBM_EMAC_RXB
int "Number of receive buffers"
depends on IBM_EMAC
- default "128" if IBM_EMAC4
- default "64"
+ default "128"
config IBM_EMAC_TXB
int "Number of transmit buffers"
depends on IBM_EMAC
- default "128" if IBM_EMAC4
- default "8"
+ default "64"
+
+config IBM_EMAC_POLL_WEIGHT
+ int "MAL NAPI polling weight"
+ depends on IBM_EMAC
+ default "32"
-config IBM_EMAC_FGAP
- int "Frame gap"
+config IBM_EMAC_RX_COPY_THRESHOLD
+ int "RX skb copy threshold (bytes)"
depends on IBM_EMAC
- default "8"
+ default "256"
-config IBM_EMAC_SKBRES
- int "Skb reserve amount"
+config IBM_EMAC_RX_SKB_HEADROOM
+ int "Additional RX skb headroom (bytes)"
depends on IBM_EMAC
default "0"
+ help
+ Additional receive skb headroom. Note, that driver
+ will always reserve at least 2 bytes to make IP header
+ aligned, so usualy there is no need to add any additional
+ headroom.
+
+ If unsure, set to 0.
+
+config IBM_EMAC_PHY_RX_CLK_FIX
+ bool "PHY Rx clock workaround"
+ depends on IBM_EMAC && (405EP || 440GX || 440EP || 440GR)
+ help
+ Enable this if EMAC attached to a PHY which doesn't generate
+ RX clock if there is no link, if this is the case, you will
+ see "TX disable timeout" or "RX disable timeout" in the system
+ log.
+
+ If unsure, say N.
+
+config IBM_EMAC_DEBUG
+ bool "Debugging"
+ depends on IBM_EMAC
+ default n
+
+config IBM_EMAC_ZMII
+ bool
+ depends on IBM_EMAC && (NP405H || NP405L || 44x)
+ default y
+
+config IBM_EMAC_RGMII
+ bool
+ depends on IBM_EMAC && 440GX
+ default y
+
+config IBM_EMAC_TAH
+ bool
+ depends on IBM_EMAC && 440GX
+ default y
config NET_PCI
bool "EISA, VLB, PCI and on board controllers"
config CS89x0
tristate "CS89x0 support"
- depends on NET_PCI && (ISA || ARCH_IXDP2X01)
+ depends on (NET_PCI && (ISA || ARCH_IXDP2X01)) || ARCH_PNX0105
---help---
Support for CS89x0 chipset based Ethernet cards. If you have a
network (Ethernet) card of this type, say Y and read the
will be called 8139cp. This is recommended.
config 8139TOO
- tristate "RealTek RTL-8139 PCI Fast Ethernet Adapter support"
+ tristate "RealTek RTL-8129/8130/8139 PCI Fast Ethernet Adapter support"
depends on NET_PCI && PCI
select CRC32
select MII
---help---
This is a driver for the Fast Ethernet PCI network cards based on
- the RTL8139 chips. If you have one of those, say Y and read
- the Ethernet-HOWTO <http://www.tldp.org/docs.html#howto>.
+ the RTL 8129/8130/8139 chips. If you have one of those, say Y and
+ read the Ethernet-HOWTO <http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here: the module
will be called 8139too. This is recommended.
tristate "SiS 900/7016 PCI Fast Ethernet Adapter support"
depends on NET_PCI && PCI
select CRC32
+ select MII
---help---
This is a driver for the Fast Ethernet PCI network cards based on
the SiS 900 and SiS 7016 chips. The SiS 900 core is also embedded in
config NET_POCKET
bool "Pocket and portable adapters"
- depends on NET_ETHERNET && ISA
+ depends on NET_ETHERNET && PARPORT
---help---
Cute little network (Ethernet) devices which attach to the parallel
port ("pocket adapters"), commonly used with laptops. If you have
config ATP
tristate "AT-LAN-TEC/RealTek pocket adapter support"
- depends on NET_POCKET && ISA && X86
+ depends on NET_POCKET && PARPORT && X86
select CRC32
---help---
This is a network (Ethernet) device which attaches to your parallel
config DE600
tristate "D-Link DE600 pocket adapter support"
- depends on NET_POCKET && ISA
+ depends on NET_POCKET && PARPORT
---help---
This is a network (Ethernet) device which attaches to your parallel
port. Read <file:Documentation/networking/DLINK.txt> as well as the
config DE620
tristate "D-Link DE620 pocket adapter support"
- depends on NET_POCKET && ISA
+ depends on NET_POCKET && PARPORT
---help---
This is a network (Ethernet) device which attaches to your parallel
port. Read <file:Documentation/networking/DLINK.txt> as well as the
the Motorola 68360 processor.
config FEC
- bool "FEC ethernet controller (of ColdFire 5272)"
- depends on M5272 || M5282
+ bool "FEC ethernet controller (of ColdFire CPUs)"
+ depends on M523x || M527x || M5272 || M528x
help
Say Y here if you want to use the built-in 10/100 Fast ethernet
- controller on the Motorola ColdFire 5272 processor.
+ controller on some Motorola ColdFire processors.
+
+config FEC2
+ bool "Second FEC ethernet controller (on some ColdFire CPUs)"
+ depends on FEC
+ help
+ Say Y here if you want to use the second built-in 10/100 Fast
+ ethernet controller on some Motorola ColdFire processors.
config NE_H8300
tristate "NE2000 compatible support for H8/300"
controller on the Renesas H8/300 processor.
source "drivers/net/fec_8xx/Kconfig"
+source "drivers/net/fs_enet/Kconfig"
endmenu
#
menu "Ethernet (1000 Mbit)"
- depends on NETDEVICES && !UML
+ depends on !UML
config ACENIC
tristate "Alteon AceNIC/3Com 3C985/NetGear GA620 Gigabit support"
If in doubt, say Y.
+config SIS190
+ tristate "SiS190/SiS191 gigabit ethernet support"
+ depends on PCI
+ select CRC32
+ select MII
+ ---help---
+ Say Y here if you have a SiS 190 PCI Fast Ethernet adapter or
+ a SiS 191 PCI Gigabit Ethernet adapter. Both are expected to
+ appear in lan on motherboard designs which are based on SiS 965
+ and SiS 966 south bridge.
+
+ To compile this driver as a module, choose M here: the module
+ will be called sis190. This is recommended.
+
+config SKGE
+ tristate "New SysKonnect GigaEthernet support (EXPERIMENTAL)"
+ depends on PCI && EXPERIMENTAL
+ select CRC32
+ ---help---
+ This driver support the Marvell Yukon or SysKonnect SK-98xx/SK-95xx
+ and related Gigabit Ethernet adapters. It is a new smaller driver
+ with better performance and more complete ethtool support.
+
+ It does not support the link failover and network management
+ features that "portable" vendor supplied sk98lin driver does.
+
config SK98LIN
tristate "Marvell Yukon Chipset / SysKonnect SK-98xx Support"
depends on PCI
To compile this driver as a module, choose M here: the module
will be called tg3. This is recommended.
+config BNX2
+ tristate "Broadcom NetXtremeII support"
+ depends on PCI
+ help
+ This driver supports Broadcom NetXtremeII gigabit Ethernet cards.
+
+ To compile this driver as a module, choose M here: the module
+ will be called bnx2. This is recommended.
+
+config SPIDER_NET
+ tristate "Spider Gigabit Ethernet driver"
+ depends on PCI && PPC_BPA
+ help
+ This driver supports the Gigabit Ethernet chips present on the
+ Cell Processor-Based Blades from IBM.
+
config GIANFAR
tristate "Gianfar Ethernet"
depends on 85xx || 83xx
+ select PHYLIB
help
This driver supports the Gigabit TSEC on the MPC85xx
family of chips, and the FEC on the 8540
#
menu "Ethernet (10000 Mbit)"
- depends on NETDEVICES && !UML
+ depends on !UML
+
+config CHELSIO_T1
+ tristate "Chelsio 10Gb Ethernet support"
+ depends on PCI
+ help
+ This driver supports Chelsio N110 and N210 models 10Gb Ethernet
+ cards. More information about adapter features and performance
+ tuning is in <file:Documentation/networking/cxgb.txt>.
+
+ For general information about Chelsio and our products, visit
+ our website at <http://www.chelsio.com>.
+
+ For customer support, please visit our customer support page at
+ <http://www.chelsio.com/support.htm>.
+
+ Please send feedback to <linux-bugs@chelsio.com>.
+
+ To compile this driver as a module, choose M here: the module
+ will be called cxgb.
config IXGB
tristate "Intel(R) PRO/10GbE support"
depends on PCI
---help---
This driver supports the 10Gbe XFrame NIC of S2IO.
- For help regarding driver compilation, installation and
- tuning please look into ~/drivers/net/s2io/README.txt.
+ More specific information on configuring the driver is in
+ <file:Documentation/networking/s2io.txt>.
config S2IO_NAPI
bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
If in doubt, say N.
-config 2BUFF_MODE
- bool "Use 2 Buffer Mode on Rx side."
- depends on S2IO
- ---help---
- On enabling the 2 buffer mode, the received frame will be
- split into 2 parts before being DMA'ed to the hosts memory.
- The parts are the ethernet header and ethernet payload.
- This is useful on systems where DMA'ing to to unaligned
- physical memory loactions comes with a heavy price.
- If not sure please say N.
-
endmenu
if !UML
config ISERIES_VETH
tristate "iSeries Virtual Ethernet driver support"
- depends on NETDEVICES && PPC_ISERIES
+ depends on PPC_ISERIES
+
+config RIONET
+ tristate "RapidIO Ethernet over messaging driver support"
+ depends on NETDEVICES && RAPIDIO
+
+config RIONET_TX_SIZE
+ int "Number of outbound queue entries"
+ depends on RIONET
+ default "128"
+
+config RIONET_RX_SIZE
+ int "Number of inbound queue entries"
+ depends on RIONET
+ default "128"
config FDDI
bool "FDDI driver support"
- depends on NETDEVICES && (PCI || EISA)
+ depends on (PCI || EISA)
help
Fiber Distributed Data Interface is a high speed local area network
design; essentially a replacement for high speed Ethernet. FDDI can
config HIPPI
bool "HIPPI driver support (EXPERIMENTAL)"
- depends on NETDEVICES && EXPERIMENTAL && INET && PCI
+ depends on EXPERIMENTAL && INET && PCI
help
HIgh Performance Parallel Interface (HIPPI) is a 800Mbit/sec and
1600Mbit/sec dual-simplex switched or point-to-point network. HIPPI
config PLIP
tristate "PLIP (parallel port) support"
- depends on NETDEVICES && PARPORT
+ depends on PARPORT
---help---
PLIP (Parallel Line Internet Protocol) is used to create a
reasonably fast mini network consisting of two (or, rarely, more)
config PPP
tristate "PPP (point-to-point protocol) support"
- depends on NETDEVICES
---help---
PPP (Point to Point Protocol) is a newer and better SLIP. It serves
the same purpose: sending Internet traffic over telephone (and other
module; it is called bsd_comp and will show up in the directory
modules once you have said "make modules". If unsure, say N.
+config PPP_MPPE
+ tristate "PPP MPPE compression (encryption) (EXPERIMENTAL)"
+ depends on PPP && EXPERIMENTAL
+ select CRYPTO
+ select CRYPTO_SHA1
+ select CRYPTO_ARC4
+ ---help---
+ Support for the MPPE Encryption protocol, as employed by the
+ Microsoft Point-to-Point Tunneling Protocol.
+
+ See http://pptpclient.sourceforge.net/ for information on
+ configuring PPTP clients and servers to utilize this method.
+
config PPPOE
tristate "PPP over Ethernet (EXPERIMENTAL)"
depends on EXPERIMENTAL && PPP
config SLIP
tristate "SLIP (serial line) support"
- depends on NETDEVICES
---help---
Say Y if you intend to use SLIP or CSLIP (compressed SLIP) to
connect to your Internet service provider or to connect to some
config NET_FC
bool "Fibre Channel driver support"
- depends on NETDEVICES && SCSI && PCI
+ depends on SCSI && PCI
help
Fibre Channel is a high speed serial protocol mainly used to connect
large storage devices to the computer; it is compatible with and
config SHAPER
tristate "Traffic Shaper (EXPERIMENTAL)"
- depends on NETDEVICES && EXPERIMENTAL
+ depends on EXPERIMENTAL
---help---
The traffic shaper is a virtual network device that allows you to
limit the rate of outgoing data flow over some other network device.
config NETCONSOLE
tristate "Network console logging support (EXPERIMENTAL)"
- depends on NETDEVICES && EXPERIMENTAL
+ depends on EXPERIMENTAL
---help---
If you want to log kernel messages over the network, enable this.
See <file:Documentation/networking/netconsole.txt> for details.
+endif #NETDEVICES
+
+config NETPOLL
+ def_bool NETCONSOLE
+
+config NETPOLL_RX
+ bool "Netpoll support for trapping incoming packets"
+ default n
+ depends on NETPOLL
+
+config NETPOLL_TRAP
+ bool "Netpoll traffic trapping"
+ default n
+ depends on NETPOLL
+
+config NET_POLL_CONTROLLER
+ def_bool NETPOLL
+
+endmenu