config MACB
tristate "Atmel MACB support"
- depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91CAP9
+ depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91SAM9G45 || ARCH_AT91CAP9
select PHYLIB
help
The Atmel MACB ethernet interface is found on many AT32 and AT91
config KS8842
tristate "Micrel KSZ8842"
+ depends on HAS_IOMEM
help
- This platform driver is for Micrel KSZ8842 chip.
+ This platform driver is for Micrel KSZ8842 / KS8842
+ 2-port ethernet switch chip (managed, VLAN, QoS).
+
+config KS8851
+ tristate "Micrel KS8851 SPI"
+ depends on SPI
+ select MII
+ select CRC32
+ help
+ SPI driver for Micrel KS8851 SPI attached network chip.
+
+config KS8851_MLL
+ tristate "Micrel KS8851 MLL"
+ depends on HAS_IOMEM
+ select MII
+ help
+ This platform driver is for Micrel KS8851 Address/data bus
+ multiplexed network chip.
config VIA_RHINE
tristate "VIA Rhine support"
config CPMAC
tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)"
- depends on NET_ETHERNET && EXPERIMENTAL && AR7 && BROKEN
+ depends on NET_ETHERNET && EXPERIMENTAL && AR7
select PHYLIB
help
TI AR7 CPMAC Ethernet support
config FEC
bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
- depends on M523x || M527x || M5272 || M528x || M520x || M532x || MACH_MX27 || ARCH_MX35
+ depends on M523x || M527x || M5272 || M528x || M520x || M532x || MACH_MX27 || ARCH_MX35 || ARCH_MX25
help
Say Y here if you want to use the built-in 10/100 Fast ethernet
controller on some Motorola ColdFire and Freescale i.MX processors.
To compile this driver as a module, choose M here. The module
will be called atl2.
+config XILINX_EMACLITE
+ tristate "Xilinx 10/100 Ethernet Lite support"
+ depends on PPC32 || MICROBLAZE
+ help
+ This driver supports the 10/100 Ethernet Lite from Xilinx.
+
+config BCM63XX_ENET
+ tristate "Broadcom 63xx internal mac support"
+ depends on BCM63XX
+ select MII
+ select PHYLIB
+ help
+ This driver supports the ethernet MACs in the Broadcom 63xx
+ MIPS chipset family (BCM63XX).
+
source "drivers/net/fs_enet/Kconfig"
endif # NET_ETHERNET
depends on SKGE && DEBUG_FS
help
This option adds the ability to dump driver state for debugging.
- The file debugfs/skge/ethX displays the state of the internal
+ The file /sys/kernel/debug/skge/ethX displays the state of the internal
transmit and receive rings.
If unsure, say N.
depends on SKY2 && DEBUG_FS
help
This option adds the ability to dump driver state for debugging.
- The file debugfs/sky2/ethX displays the state of the internal
+ The file /sys/kernel/debug/sky2/ethX displays the state of the internal
transmit and receive rings.
If unsure, say N.
config CNIC
tristate "Broadcom CNIC support"
- depends on BNX2
- depends on UIO
+ depends on PCI
+ select BNX2
+ select UIO
help
This driver supports offload features of Broadcom NetXtremeII
gigabit Ethernet cards.
This driver supports the Gigabit Ethernet mode of the QUICC Engine,
which is available on some Freescale SOCs.
-config UGETH_MAGIC_PACKET
- bool "Magic Packet detection support"
- depends on UCC_GETH
-
config UGETH_TX_ON_DEMAND
bool "Transmit on Demand support"
depends on UCC_GETH
To compile this driver as a module, choose M here. The module
will be called jme.
+config S6GMAC
+ tristate "S6105 GMAC ethernet support"
+ depends on XTENSA_VARIANT_S6000
+ select PHYLIB
+ help
+ This driver supports the on chip ethernet device on the
+ S6105 xtensa processor.
+
+ To compile this driver as a module, choose M here. The module
+ will be called s6gmac.
+
+source "drivers/net/stmmac/Kconfig"
+
endif # NETDEV_1000
#
select FW_LOADER
select ZLIB_INFLATE
select LIBCRC32C
+ select MDIO
help
This driver supports Broadcom NetXtremeII 10 gigabit Ethernet cards.
To compile this driver as a module, choose M here: the module
This is the virtual network driver for virtio. It can be used with
lguest or QEMU based VMMs (like KVM or Xen). Say Y or M.
+config VMXNET3
+ tristate "VMware VMXNET3 ethernet driver"
+ depends on PCI && X86 && INET
+ help
+ This driver supports VMware's vmxnet3 virtual ethernet NIC.
+ To compile this driver as a module, choose M here: the
+ module will be called vmxnet3.
+
endif # NETDEVICES