# Network device configuration
#
-menu "Network device support"
- depends on NET
-
-config NETDEVICES
+menuconfig NETDEVICES
default y if UML
bool "Network device support"
---help---
# Ethernet
#
-menu "Ethernet (10 or 100Mbit)"
- depends on !UML
-
-config NET_ETHERNET
+menuconfig NET_ETHERNET
bool "Ethernet (10 or 100Mbit)"
+ depends on !UML
---help---
Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common
type of Local Area Network (LAN) in universities and companies.
kernel: saying N will just cause the configurator to skip all
the questions about Ethernet network cards. If unsure, say N.
+if NET_ETHERNET
+
config MII
tristate "Generic Media Independent Interface device support"
- depends on NET_ETHERNET
help
Most ethernet controllers have MII transceiver either as an external
or internal device. It is safe to say Y or M here even if your
ethernet card lack MII.
+config MACB
+ tristate "Atmel MACB support"
+ depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263
+ select MII
+ help
+ The Atmel MACB ethernet interface is found on many AT32 and AT91
+ parts. Say Y to include support for the MACB chip.
+
+ To compile this driver as a module, choose M here: the module
+ will be called macb.
+
source "drivers/net/arm/Kconfig"
+config AX88796
+ tristate "ASIX AX88796 NE2000 clone support"
+ depends on ARM || MIPS
+ select CRC32
+ select MII
+ help
+ AX88796 driver, using platform bus to provide
+ chip detection and resources
+
config MACE
tristate "MACE (Power Mac ethernet) support"
- depends on NET_ETHERNET && PPC_PMAC && PPC32
+ depends on PPC_PMAC && PPC32
select CRC32
help
Power Macintoshes and clones with Ethernet built-in on the
config BMAC
tristate "BMAC (G3 ethernet) support"
- depends on NET_ETHERNET && PPC_PMAC && PPC32
+ depends on PPC_PMAC && PPC32
select CRC32
help
Say Y for support of BMAC Ethernet interfaces. These are used on G3
To compile this driver as a module, choose M here: the module
will be called bmac.
-config OAKNET
- tristate "National DP83902AV (Oak ethernet) support"
- depends on NET_ETHERNET && PPC && BROKEN
- select CRC32
- help
- Say Y if your machine has this type of Ethernet network card.
-
- To compile this driver as a module, choose M here: the module
- will be called oaknet.
-
config ARIADNE
tristate "Ariadne support"
- depends on NET_ETHERNET && ZORRO
+ depends on ZORRO
help
If you have a Village Tronic Ariadne Ethernet adapter, say Y.
Otherwise, say N.
config A2065
tristate "A2065 support"
- depends on NET_ETHERNET && ZORRO
+ depends on ZORRO
select CRC32
help
If you have a Commodore A2065 Ethernet adapter, say Y. Otherwise,
config HYDRA
tristate "Hydra support"
- depends on NET_ETHERNET && ZORRO
+ depends on ZORRO
select CRC32
help
If you have a Hydra Ethernet adapter, say Y. Otherwise, say N.
config ZORRO8390
tristate "Zorro NS8390-based Ethernet support"
- depends on NET_ETHERNET && ZORRO
+ depends on ZORRO
select CRC32
help
This driver is for Zorro Ethernet cards using an NS8390-compatible
config APNE
tristate "PCMCIA NE2000 support"
- depends on NET_ETHERNET && AMIGA_PCMCIA
+ depends on AMIGA_PCMCIA
select CRC32
help
If you have a PCMCIA NE2000 compatible adapter, say Y. Otherwise,
config APOLLO_ELPLUS
tristate "Apollo 3c505 support"
- depends on NET_ETHERNET && APOLLO
+ depends on APOLLO
help
Say Y or M here if your Apollo has a 3Com 3c505 ISA Ethernet card.
If you don't have one made for Apollos, you can use one from a PC,
config MAC8390
bool "Macintosh NS 8390 based ethernet cards"
- depends on NET_ETHERNET && MAC
+ depends on MAC
select CRC32
help
If you want to include a driver to support Nubus or LC-PDS
config MAC89x0
tristate "Macintosh CS89x0 based ethernet cards"
- depends on NET_ETHERNET && MAC && BROKEN
+ depends on MAC
---help---
Support for CS89x0 chipset based Ethernet cards. If you have a
Nubus or LC-PDS network (Ethernet) card of this type, say Y and
config MACSONIC
tristate "Macintosh SONIC based ethernet (onboard, NuBus, LC, CS)"
- depends on NET_ETHERNET && MAC
+ depends on MAC
---help---
Support for NatSemi SONIC based Ethernet devices. This includes
the onboard Ethernet in many Quadras as well as some LC-PDS,
be called macsonic.
config MACMACE
- bool "Macintosh (AV) onboard MACE ethernet (EXPERIMENTAL)"
- depends on NET_ETHERNET && MAC && EXPERIMENTAL
+ bool "Macintosh (AV) onboard MACE ethernet"
+ depends on MAC
select CRC32
help
Support for the onboard AMD 79C940 MACE Ethernet controller used in
config MVME147_NET
tristate "MVME147 (Lance) Ethernet support"
- depends on NET_ETHERNET && MVME147
+ depends on MVME147
select CRC32
help
Support for the on-board Ethernet interface on the Motorola MVME147
config MVME16x_NET
tristate "MVME16x Ethernet support"
- depends on NET_ETHERNET && MVME16x
+ depends on MVME16x
help
This is the driver for the Ethernet interface on the Motorola
MVME162, 166, 167, 172 and 177 boards. Say Y here to include the
config BVME6000_NET
tristate "BVME6000 Ethernet support"
- depends on NET_ETHERNET && BVME6000
+ depends on BVME6000
help
This is the driver for the Ethernet interface on BVME4000 and
BVME6000 VME boards. Say Y here to include the driver for this chip
config ATARILANCE
tristate "Atari Lance support"
- depends on NET_ETHERNET && ATARI
+ depends on ATARI
help
Say Y to include support for several Atari Ethernet adapters based
on the AMD Lance chipset: RieblCard (with or without battery), or
config ATARI_BIONET
tristate "BioNet-100 support"
- depends on NET_ETHERNET && ATARI && ATARI_ACSI && BROKEN
+ depends on ATARI && ATARI_ACSI && BROKEN
help
Say Y to include support for BioData's BioNet-100 Ethernet adapter
for the ACSI port. The driver works (has to work...) with a polled
config ATARI_PAMSNET
tristate "PAMsNet support"
- depends on NET_ETHERNET && ATARI && ATARI_ACSI && BROKEN
+ depends on ATARI && ATARI_ACSI && BROKEN
help
Say Y to include support for the PAMsNet Ethernet adapter for the
ACSI port ("ACSI node"). The driver works (has to work...) with a
config SUN3LANCE
tristate "Sun3/Sun3x on-board LANCE support"
- depends on NET_ETHERNET && (SUN3 || SUN3X)
+ depends on SUN3 || SUN3X
help
Most Sun3 and Sun3x motherboards (including the 3/50, 3/60 and 3/80)
featured an AMD Lance 10Mbit Ethernet controller on board; say Y
config SUN3_82586
bool "Sun3 on-board Intel 82586 support"
- depends on NET_ETHERNET && SUN3
+ depends on SUN3
help
This driver enables support for the on-board Intel 82586 based
Ethernet adapter found on Sun 3/1xx and 3/2xx motherboards. Note
config HPLANCE
bool "HP on-board LANCE support"
- depends on NET_ETHERNET && DIO
+ depends on DIO
select CRC32
help
If you want to use the builtin "LANCE" Ethernet controller on an
config LASI_82596
tristate "Lasi ethernet"
- depends on NET_ETHERNET && PARISC && GSC_LASI
+ depends on GSC
+ help
+ Say Y here to support the builtin Intel 82596 ethernet controller
+ found in Hewlett-Packard PA-RISC machines with 10Mbit ethernet.
+
+config SNI_82596
+ tristate "SNI RM ethernet"
+ depends on NET_ETHERNET && SNI_RM
help
Say Y here to support the on-board Intel 82596 ethernet controller
- built into Hewlett-Packard PA-RISC machines.
+ built into SNI RM machines.
config MIPS_JAZZ_SONIC
tristate "MIPS JAZZ onboard SONIC Ethernet support"
- depends on NET_ETHERNET && MACH_JAZZ
+ depends on MACH_JAZZ
help
This is the driver for the onboard card of MIPS Magnum 4000,
Acer PICA, Olivetti M700-10 and a few other identical OEM systems.
config MIPS_AU1X00_ENET
bool "MIPS AU1000 Ethernet support"
- depends on NET_ETHERNET && SOC_AU1X00
+ depends on SOC_AU1X00
select PHYLIB
select CRC32
help
config NET_SB1250_MAC
tristate "SB1250 Ethernet support"
- depends on NET_ETHERNET && SIBYTE_SB1xxx_SOC
+ depends on SIBYTE_SB1xxx_SOC
config SGI_IOC3_ETH
bool "SGI IOC3 Ethernet"
- depends on NET_ETHERNET && PCI && SGI_IP27
+ depends on PCI && SGI_IP27
select CRC32
select MII
help
enables offloading for checksums on transmit. If unsure, say Y.
config MIPS_SIM_NET
- tristate "MIPS simulator Network device (EXPERIMENTAL)"
- depends on MIPS_SIM && EXPERIMENTAL
+ tristate "MIPS simulator Network device"
+ depends on MIPS_SIM
help
The MIPSNET device is a simple Ethernet network device which is
emulated by the MIPS Simulator.
config SGI_O2MACE_ETH
tristate "SGI O2 MACE Fast Ethernet support"
- depends on NET_ETHERNET && SGI_IP32=y
+ depends on SGI_IP32=y
config STNIC
tristate "National DP83902AV support"
- depends on NET_ETHERNET && SUPERH
+ depends on SUPERH
select CRC32
help
Support for cards based on the National Semiconductor DP83902AV
config SUNLANCE
tristate "Sun LANCE support"
- depends on NET_ETHERNET && SBUS
+ depends on SBUS
select CRC32
help
This driver supports the "le" interface present on all 32-bit Sparc
config HAPPYMEAL
tristate "Sun Happy Meal 10/100baseT support"
- depends on NET_ETHERNET && (SBUS || PCI)
+ depends on SBUS || PCI
select CRC32
help
This driver supports the "hme" interface present on most Ultra
config SUNBMAC
tristate "Sun BigMAC 10/100baseT support (EXPERIMENTAL)"
- depends on NET_ETHERNET && SBUS && EXPERIMENTAL
+ depends on SBUS && EXPERIMENTAL
select CRC32
help
This driver supports the "be" interface available as an Sbus option.
config SUNQE
tristate "Sun QuadEthernet support"
- depends on NET_ETHERNET && SBUS
+ depends on SBUS
select CRC32
help
This driver supports the "qe" 10baseT Ethernet device, available as
config SUNGEM
tristate "Sun GEM support"
- depends on NET_ETHERNET && PCI
+ depends on PCI
select CRC32
help
Support for the Sun GEM chip, aka Sun GigabitEthernet/P 2.0. See also
config CASSINI
tristate "Sun Cassini support"
- depends on NET_ETHERNET && PCI
+ depends on PCI
select CRC32
help
Support for the Sun Cassini chip, aka Sun GigaSwift Ethernet. See also
config NET_VENDOR_3COM
bool "3COM cards"
- depends on NET_ETHERNET && (ISA || EISA || MCA || PCI)
+ depends on ISA || EISA || MCA || PCI
help
If you have a network (Ethernet) card belonging to this class, say Y
and read the Ethernet-HOWTO, available from
config LANCE
tristate "AMD LANCE and PCnet (AT1500 and NE2100) support"
- depends on NET_ETHERNET && ISA && ISA_DMA_API
+ depends on ISA && ISA_DMA_API
help
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
config NET_VENDOR_SMC
bool "Western Digital/SMC cards"
- depends on NET_ETHERNET && (ISA || MCA || EISA || MAC)
+ depends on ISA || MCA || EISA || MAC
help
If you have a network (Ethernet) card belonging to this class, say Y
and read the Ethernet-HOWTO, available from
<file:Documentation/networking/net-modules.txt>. The module
will be called smc-ultra32.
-config SMC91X
- tristate "SMC 91C9x/91C1xxx support"
- select CRC32
- select MII
- depends on NET_ETHERNET && (ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || SOC_AU1X00)
- help
- This is a driver for SMC's 91x series of Ethernet chipsets,
- including the SMC91C94 and the SMC91C111. Say Y if you want it
- compiled into the kernel, and read the file
- <file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO,
- available from <http://www.linuxdoc.org/docs.html#howto>.
-
- This driver is also available as a module ( = code which can be
- inserted in and removed from the running kernel whenever you want).
- The module will be called smc91x. If you want to compile it as a
- module, say M here and read <file:Documentation/modules.txt> as well
- as <file:Documentation/networking/net-modules.txt>.
-
config SMC9194
tristate "SMC 9194 support"
depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN)
<file:Documentation/networking/net-modules.txt>. The module
will be called smc9194.
+config SMC91X
+ tristate "SMC 91C9x/91C1xxx support"
+ select CRC32
+ select MII
+ depends on ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || SOC_AU1X00 || BFIN
+ help
+ This is a driver for SMC's 91x series of Ethernet chipsets,
+ including the SMC91C94 and the SMC91C111. Say Y if you want it
+ compiled into the kernel, and read the file
+ <file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO,
+ available from <http://www.linuxdoc.org/docs.html#howto>.
+
+ This driver is also available as a module ( = code which can be
+ inserted in and removed from the running kernel whenever you want).
+ The module will be called smc91x. If you want to compile it as a
+ module, say M here and read <file:Documentation/kbuild/modules.txt>
+ as well as <file:Documentation/networking/net-modules.txt>.
+
config NET_NETX
tristate "NetX Ethernet support"
select MII
- depends on NET_ETHERNET && ARCH_NETX
+ depends on ARCH_NETX
help
This is support for the Hilscher netX builtin Ethernet ports
config DM9000
tristate "DM9000 support"
- depends on (ARM || MIPS) && NET_ETHERNET
+ depends on ARM || MIPS
select CRC32
select MII
---help---
tristate "SMSC LAN911[5678] support"
select CRC32
select MII
- depends on NET_ETHERNET && ARCH_PXA
+ depends on ARCH_PXA
help
This is a driver for SMSC's LAN911x series of Ethernet chipsets
including the new LAN9115, LAN9116, LAN9117, and LAN9118.
This driver is also available as a module. The module will be
called smc911x. If you want to compile it as a module, say M
- here and read <file:Documentation/modules.txt>
+ here and read <file:Documentation/kbuild/modules.txt>
config NET_VENDOR_RACAL
bool "Racal-Interlan (Micom) NI cards"
- depends on NET_ETHERNET && ISA
+ depends on ISA
help
If you have a network (Ethernet) card belonging to this class, such
as the NI5010, NI5210 or NI6210, say Y and read the Ethernet-HOWTO,
config AT1700
tristate "AT1700/1720 support (EXPERIMENTAL)"
- depends on NET_ETHERNET && (ISA || MCA_LEGACY) && EXPERIMENTAL
+ depends on (ISA || MCA_LEGACY) && EXPERIMENTAL
select CRC32
---help---
If you have a network (Ethernet) card of this type, say Y and read
config DEPCA
tristate "DEPCA, DE10x, DE200, DE201, DE202, DE422 support"
- depends on NET_ETHERNET && (ISA || EISA || MCA)
+ depends on ISA || EISA || MCA
select CRC32
---help---
If you have a network (Ethernet) card of this type, say Y and read
config HP100
tristate "HP 10/100VG PCLAN (ISA, EISA, PCI) support"
- depends on NET_ETHERNET && (ISA || EISA || PCI)
+ depends on ISA || EISA || PCI
help
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
config NET_ISA
bool "Other ISA cards"
- depends on NET_ETHERNET && ISA
+ depends on ISA
---help---
If your network (Ethernet) card hasn't been mentioned yet and its
bus system (that's the way the cards talks to the other components
config NE2000
tristate "NE2000/NE1000 support"
- depends on NET_ISA || (Q40 && m) || M32R
+ depends on NET_ISA || (Q40 && m) || M32R || TOSHIBA_RBTX4927 || TOSHIBA_RBTX4938
select CRC32
---help---
If you have a network (Ethernet) card of this type, say Y and read
<file:Documentation/networking/net-modules.txt>. The module
will be called seeq8005.
-config SKMC
- tristate "SKnet MCA support"
- depends on NET_ETHERNET && MCA && BROKEN
- ---help---
- These are Micro Channel Ethernet adapters. You need to say Y to "MCA
- support" in order to use this driver. Supported cards are the SKnet
- Junior MC2 and the SKnet MC2(+). The driver automatically
- distinguishes between the two cards. Note that using multiple boards
- of different type hasn't been tested with this driver. Say Y if you
- have one of these Ethernet adapters.
-
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
- will be called sk_mca.
-
config NE2_MCA
tristate "NE/2 (ne2000 MCA version) support"
- depends on NET_ETHERNET && MCA_LEGACY
+ depends on MCA_LEGACY
select CRC32
help
If you have a network (Ethernet) card of this type, say Y and read
config IBMLANA
tristate "IBM LAN Adapter/A support"
- depends on NET_ETHERNET && MCA && MCA_LEGACY
+ depends on MCA && MCA_LEGACY
---help---
This is a Micro Channel Ethernet adapter. You need to set
CONFIG_MCA to use this driver. It is both available as an in-kernel
config IBMVETH
tristate "IBM LAN Virtual Ethernet support"
- depends on NET_ETHERNET && PPC_PSERIES
+ depends on PPC_PSERIES
---help---
This driver supports virtual ethernet adapters on newer IBM iSeries
and pSeries systems.
config IBM_EMAC
tristate "PowerPC 4xx on-chip Ethernet support"
- depends on 4xx
+ depends on 4xx && !PPC_MERGE
help
This driver supports the PowerPC 4xx EMAC family of on-chip
Ethernet controllers.
config NET_PCI
bool "EISA, VLB, PCI and on board controllers"
- depends on NET_ETHERNET && (ISA || EISA || PCI)
+ depends on ISA || EISA || PCI
help
This is another class of network cards which attach directly to the
bus. If you have one of those, say Y and read the Ethernet-HOWTO,
will be called pcnet32.
config PCNET32_NAPI
- bool "Use RX polling (NAPI) (EXPERIMENTAL)"
- depends on PCNET32 && EXPERIMENTAL
+ bool "Use RX polling (NAPI)"
+ depends on PCNET32
help
NAPI is a new driver API designed to reduce CPU and interrupt load
when the driver is receiving lots of packets from the card. It is
To compile this driver as a module, choose M here and read
<file:Documentation/networking/net-modules.txt>. The module
will be called amd8111e.
+
config AMD8111E_NAPI
bool "Enable NAPI support"
depends on AMD8111_ETH
config TC35815
tristate "TOSHIBA TC35815 Ethernet support"
- depends on NET_PCI && PCI && TOSHIBA_JMR3927
+ depends on NET_PCI && PCI && MIPS
+ select MII
config DGRS
tristate "Digi Intl. RightSwitch SE-X support"
information.
config LAN_SAA9730
- bool "Philips SAA9730 Ethernet support (EXPERIMENTAL)"
- depends on NET_PCI && EXPERIMENTAL && MIPS
+ bool "Philips SAA9730 Ethernet support"
+ depends on NET_PCI && PCI && MIPS_ATLAS
help
The SAA9730 is a combined multimedia and peripheral controller used
in thin clients, Internet access terminals, and diskless
workstations.
See <http://www.semiconductors.philips.com/pip/SAA9730_flyer_1>.
+config SC92031
+ tristate "Silan SC92031 PCI Fast Ethernet Adapter driver (EXPERIMENTAL)"
+ depends on NET_PCI && PCI && EXPERIMENTAL
+ select CRC32
+ ---help---
+ This is a driver for the Fast Ethernet PCI network cards based on
+ the Silan SC92031 chip (sometimes also called Rsltek 8139D). If you
+ have one of these, say Y here.
+
+ To compile this driver as a module, choose M here: the module
+ will be called sc92031. This is recommended.
+
config NET_POCKET
bool "Pocket and portable adapters"
- depends on NET_ETHERNET && PARPORT
+ depends on PARPORT
---help---
Cute little network (Ethernet) devices which attach to the parallel
port ("pocket adapters"), commonly used with laptops. If you have
config SGISEEQ
tristate "SGI Seeq ethernet controller support"
- depends on NET_ETHERNET && SGI_IP22
+ depends on SGI_IP22
help
Say Y here if you have an Seeq based Ethernet network card. This is
used in many Silicon Graphics machines.
config DECLANCE
tristate "DEC LANCE ethernet controller support"
- depends on NET_ETHERNET && MACH_DECSTATION
+ depends on MACH_DECSTATION
select CRC32
help
This driver is for the series of Ethernet controllers produced by
config NE_H8300
tristate "NE2000 compatible support for H8/300"
- depends on H8300 && NET_ETHERNET
+ depends on H8300
help
Say Y here if you want to use the NE2000 compatible
controller on the Renesas H8/300 processor.
source "drivers/net/fec_8xx/Kconfig"
source "drivers/net/fs_enet/Kconfig"
-endmenu
+endif # NET_ETHERNET
#
# Gigabit Ethernet
#
-menu "Ethernet (1000 Mbit)"
+menuconfig NETDEV_1000
+ bool "Ethernet (1000 Mbit)"
depends on !UML
+ default y
+
+if NETDEV_1000
config ACENIC
tristate "Alteon AceNIC/3Com 3C985/NetGear GA620 Gigabit support"
with better performance and more complete ethtool support.
It does not support the link failover and network management
- features that "portable" vendor supplied sk98lin driver does.
+ features available in the hardware.
This driver supports adapters based on the original Yukon chipset:
Marvell 88E8001, Belkin F5D5005, CNet GigaCard, DLink DGE-530T,
will be called skge. This is recommended.
config SKY2
- tristate "SysKonnect Yukon2 support (EXPERIMENTAL)"
+ tristate "SysKonnect Yukon2 support"
depends on PCI
select CRC32
---help---
To compile this driver as a module, choose M here: the module
will be called sky2. This is recommended.
-config SK98LIN
- tristate "Marvell Yukon Chipset / SysKonnect SK-98xx Support"
- depends on PCI
- ---help---
- Say Y here if you have a Marvell Yukon or SysKonnect SK-98xx/SK-95xx
- compliant Gigabit Ethernet Adapter.
-
- This driver supports the original Yukon chipset. A cleaner driver is
- also available (skge) which seems to work better than this one.
+config SKY2_DEBUG
+ bool "Debugging interface"
+ depends on SKY2 && DEBUG_FS
+ help
+ This option adds the ability to dump driver state for debugging.
+ The file debugfs/sky2/ethX displays the state of the internal
+ transmit and receive rings.
- This driver does not support the newer Yukon2 chipset. A separate
- driver, sky2, is provided to support Yukon2-based adapters.
-
- The following adapters are supported by this driver:
- - 3Com 3C940 Gigabit LOM Ethernet Adapter
- - 3Com 3C941 Gigabit LOM Ethernet Adapter
- - Allied Telesyn AT-2970LX Gigabit Ethernet Adapter
- - Allied Telesyn AT-2970LX/2SC Gigabit Ethernet Adapter
- - Allied Telesyn AT-2970SX Gigabit Ethernet Adapter
- - Allied Telesyn AT-2970SX/2SC Gigabit Ethernet Adapter
- - Allied Telesyn AT-2970TX Gigabit Ethernet Adapter
- - Allied Telesyn AT-2970TX/2TX Gigabit Ethernet Adapter
- - Allied Telesyn AT-2971SX Gigabit Ethernet Adapter
- - Allied Telesyn AT-2971T Gigabit Ethernet Adapter
- - Belkin Gigabit Desktop Card 10/100/1000Base-T Adapter, Copper RJ-45
- - EG1032 v2 Instant Gigabit Network Adapter
- - EG1064 v2 Instant Gigabit Network Adapter
- - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Abit)
- - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Albatron)
- - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Asus)
- - Marvell 88E8001 Gigabit LOM Ethernet Adapter (ECS)
- - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Epox)
- - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Foxconn)
- - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Gigabyte)
- - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Iwill)
- - Marvell 88E8050 Gigabit LOM Ethernet Adapter (Intel)
- - Marvell RDK-8001 Adapter
- - Marvell RDK-8002 Adapter
- - Marvell RDK-8003 Adapter
- - Marvell RDK-8004 Adapter
- - Marvell RDK-8006 Adapter
- - Marvell RDK-8007 Adapter
- - Marvell RDK-8008 Adapter
- - Marvell RDK-8009 Adapter
- - Marvell RDK-8010 Adapter
- - Marvell RDK-8011 Adapter
- - Marvell RDK-8012 Adapter
- - Marvell RDK-8052 Adapter
- - Marvell Yukon Gigabit Ethernet 10/100/1000Base-T Adapter (32 bit)
- - Marvell Yukon Gigabit Ethernet 10/100/1000Base-T Adapter (64 bit)
- - N-Way PCI-Bus Giga-Card 1000/100/10Mbps(L)
- - SK-9521 10/100/1000Base-T Adapter
- - SK-9521 V2.0 10/100/1000Base-T Adapter
- - SK-9821 Gigabit Ethernet Server Adapter (SK-NET GE-T)
- - SK-9821 V2.0 Gigabit Ethernet 10/100/1000Base-T Adapter
- - SK-9822 Gigabit Ethernet Server Adapter (SK-NET GE-T dual link)
- - SK-9841 Gigabit Ethernet Server Adapter (SK-NET GE-LX)
- - SK-9841 V2.0 Gigabit Ethernet 1000Base-LX Adapter
- - SK-9842 Gigabit Ethernet Server Adapter (SK-NET GE-LX dual link)
- - SK-9843 Gigabit Ethernet Server Adapter (SK-NET GE-SX)
- - SK-9843 V2.0 Gigabit Ethernet 1000Base-SX Adapter
- - SK-9844 Gigabit Ethernet Server Adapter (SK-NET GE-SX dual link)
- - SK-9851 V2.0 Gigabit Ethernet 1000Base-SX Adapter
- - SK-9861 Gigabit Ethernet Server Adapter (SK-NET GE-SX Volition)
- - SK-9861 V2.0 Gigabit Ethernet 1000Base-SX Adapter
- - SK-9862 Gigabit Ethernet Server Adapter (SK-NET GE-SX Volition dual link)
- - SK-9871 Gigabit Ethernet Server Adapter (SK-NET GE-ZX)
- - SK-9871 V2.0 Gigabit Ethernet 1000Base-ZX Adapter
- - SK-9872 Gigabit Ethernet Server Adapter (SK-NET GE-ZX dual link)
- - SMC EZ Card 1000 (SMC9452TXV.2)
-
- The adapters support Jumbo Frames.
- The dual link adapters support link-failover and dual port features.
- Both Marvell Yukon and SysKonnect SK-98xx/SK-95xx adapters support
- the scatter-gather functionality with sendfile(). Please refer to
- <file:Documentation/networking/sk98lin.txt> for more information about
- optional driver parameters.
- Questions concerning this driver may be addressed to:
- <linux@syskonnect.de>
-
- If you want to compile this driver as a module ( = code which can be
- inserted in and removed from the running kernel whenever you want),
- say M here and read <file:Documentation/kbuild/modules.txt>. The module will
- be called sk98lin. This is recommended.
+ If unsure, say N.
config VIA_VELOCITY
tristate "VIA Velocity support"
- depends on NET_PCI && PCI
+ depends on PCI
select CRC32
select CRC_CCITT
select MII
config SPIDER_NET
tristate "Spider Gigabit Ethernet driver"
- depends on PCI && PPC_IBM_CELL_BLADE
+ depends on PCI && (PPC_IBM_CELL_BLADE || PPC_CELLEB)
select FW_LOADER
help
This driver supports the Gigabit Ethernet chips present on the
Cell Processor-Based Blades from IBM.
+config TSI108_ETH
+ tristate "Tundra TSI108 gigabit Ethernet support"
+ depends on TSI108_BRIDGE
+ help
+ This driver supports Tundra TSI108 gigabit Ethernet ports.
+ To compile this driver as a module, choose M here: the module
+ will be called tsi108_eth.
+
+config GELIC_NET
+ tristate "PS3 Gigabit Ethernet driver"
+ depends on PPC_PS3
+ help
+ This driver supports the network device on the PS3 game
+ console. This driver has built-in support for Ethernet.
+
+ To compile this driver as a module, choose M here: the
+ module will be called ps3_gelic.
+
config GIANFAR
tristate "Gianfar Ethernet"
depends on 85xx || 83xx || PPC_86xx
select PHYLIB
+ select CRC32
help
This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
and MPC86xx family of chips, and the FEC on the 8540.
depends on GIANFAR
config UCC_GETH
- tristate "Freescale QE UCC GETH"
- depends on QUICC_ENGINE && UCC_FAST
+ tristate "Freescale QE Gigabit Ethernet"
+ depends on QUICC_ENGINE
+ select PHYLIB
help
- This driver supports the Gigabit Ethernet mode of QE UCC.
- QE can be found on MPC836x CPUs.
+ This driver supports the Gigabit Ethernet mode of the QUICC Engine,
+ which is available on some Freescale SOCs.
config UGETH_NAPI
bool "NAPI Support"
bool "Mac address filtering support"
depends on UCC_GETH
-config UGETH_TX_ON_DEMOND
- bool "Transmit on Demond support"
+config UGETH_TX_ON_DEMAND
+ bool "Transmit on Demand support"
depends on UCC_GETH
-config UGETH_HAS_GIGA
- bool
- depends on UCC_GETH && PPC_MPC836x
-
config MV643XX_ETH
tristate "MV-643XX Ethernet support"
- depends on MOMENCO_OCELOT_C || MOMENCO_JAGUAR_ATX || MV64360 || MOMENCO_OCELOT_3 || (PPC_MULTIPLATFORM && PPC32)
+ depends on MV64360 || MV64X60 || (PPC_MULTIPLATFORM && PPC32)
select MII
help
This driver supports the gigabit Ethernet on the Marvell MV643XX
chipset which is used in the Momenco Ocelot C and Jaguar ATX and
Pegasos II, amongst other PPC and MIPS boards.
-config MV643XX_ETH_0
- bool "MV-643XX Port 0"
- depends on MV643XX_ETH
- help
- This enables support for Port 0 of the Marvell MV643XX Gigabit
- Ethernet.
-
-config MV643XX_ETH_1
- bool "MV-643XX Port 1"
- depends on MV643XX_ETH
- help
- This enables support for Port 1 of the Marvell MV643XX Gigabit
- Ethernet.
-
-config MV643XX_ETH_2
- bool "MV-643XX Port 2"
- depends on MV643XX_ETH
- help
- This enables support for Port 2 of the Marvell MV643XX Gigabit
- Ethernet.
-
config QLA3XXX
tristate "QLogic QLA3XXX Network Driver Support"
depends on PCI
To compile this driver as a module, choose M here: the module
will be called qla3xxx.
-endmenu
+config ATL1
+ tristate "Attansic L1 Gigabit Ethernet support (EXPERIMENTAL)"
+ depends on PCI && EXPERIMENTAL
+ select CRC32
+ select MII
+ help
+ This driver supports the Attansic L1 gigabit ethernet adapter.
+
+ To compile this driver as a module, choose M here. The module
+ will be called atl1.
+
+endif # NETDEV_1000
#
# 10 Gigabit Ethernet
#
-menu "Ethernet (10000 Mbit)"
+menuconfig NETDEV_10000
+ bool "Ethernet (10000 Mbit)"
depends on !UML
+ default y
+
+if NETDEV_10000
config CHELSIO_T1
tristate "Chelsio 10Gb Ethernet support"
depends on PCI
+ select CRC32
help
- This driver supports Chelsio N110 and N210 models 10Gb Ethernet
- cards. More information about adapter features and performance
- tuning is in <file:Documentation/networking/cxgb.txt>.
+ This driver supports Chelsio gigabit and 10-gigabit
+ Ethernet cards. More information about adapter features and
+ performance tuning is in <file:Documentation/networking/cxgb.txt>.
For general information about Chelsio and our products, visit
our website at <http://www.chelsio.com>.
To compile this driver as a module, choose M here: the module
will be called cxgb.
+config CHELSIO_T1_1G
+ bool "Chelsio gigabit Ethernet support"
+ depends on CHELSIO_T1
+ help
+ Enables support for Chelsio's gigabit Ethernet PCI cards. If you
+ are using only 10G cards say 'N' here.
+
+config CHELSIO_T1_NAPI
+ bool "Use Rx Polling (NAPI)"
+ depends on CHELSIO_T1
+ default y
+ help
+ NAPI is a driver API designed to reduce CPU and interrupt load
+ when the driver is receiving lots of packets from the card.
+
+config CHELSIO_T3
+ tristate "Chelsio Communications T3 10Gb Ethernet support"
+ depends on PCI
+ select FW_LOADER
+ help
+ This driver supports Chelsio T3-based gigabit and 10Gb Ethernet
+ adapters.
+
+ For general information about Chelsio and our products, visit
+ our website at <http://www.chelsio.com>.
+
+ For customer support, please visit our customer support page at
+ <http://www.chelsio.com/support.htm>.
+
+ Please send feedback to <linux-bugs@chelsio.com>.
+
+ To compile this driver as a module, choose M here: the module
+ will be called cxgb3.
+
config EHEA
tristate "eHEA Ethernet support"
depends on IBMEBUS
<file:Documentation/networking/net-modules.txt>. The module
will be called myri10ge.
-endmenu
+config NETXEN_NIC
+ tristate "NetXen Multi port (1/10) Gigabit Ethernet NIC"
+ depends on PCI
+ help
+ This enables the support for NetXen's Gigabit Ethernet card.
+
+config PASEMI_MAC
+ tristate "PA Semi 1/10Gbit MAC"
+ depends on PPC64 && PCI
+ select PHYLIB
+ help
+ This driver supports the on-chip 1/10Gbit Ethernet controller on
+ PA Semi's PWRficient line of chips.
+
+config MLX4_CORE
+ tristate
+ depends on PCI
+ default n
+
+config MLX4_DEBUG
+ bool "Verbose debugging output" if (MLX4_CORE && EMBEDDED)
+ depends on MLX4_CORE
+ default y
+ ---help---
+ This option causes debugging code to be compiled into the
+ mlx4_core driver. The output can be turned on via the
+ debug_level module parameter (which can also be set after
+ the driver is loaded through sysfs).
+
+endif # NETDEV_10000
source "drivers/net/tokenring/Kconfig"
source "drivers/net/wireless/Kconfig"
+source "drivers/net/usb/Kconfig"
+
source "drivers/net/pcmcia/Kconfig"
source "drivers/net/wan/Kconfig"
config FDDI
bool "FDDI driver support"
- depends on (PCI || EISA)
+ depends on (PCI || EISA || TC)
help
Fiber Distributed Data Interface is a high speed local area network
design; essentially a replacement for high speed Ethernet. FDDI can
will say N.
config DEFXX
- tristate "Digital DEFEA and DEFPA adapter support"
- depends on FDDI && (PCI || EISA)
- help
- This is support for the DIGITAL series of EISA (DEFEA) and PCI
- (DEFPA) controllers which can connect you to a local FDDI network.
+ tristate "Digital DEFTA/DEFEA/DEFPA adapter support"
+ depends on FDDI && (PCI || EISA || TC)
+ ---help---
+ This is support for the DIGITAL series of TURBOchannel (DEFTA),
+ EISA (DEFEA) and PCI (DEFPA) controllers which can connect you
+ to a local FDDI network.
+
+ To compile this driver as a module, choose M here: the module
+ will be called defxx. If unsure, say N.
+
+config DEFXX_MMIO
+ bool
+ prompt "Use MMIO instead of PIO" if PCI || EISA
+ depends on DEFXX
+ default n if PCI || EISA
+ default y
+ ---help---
+ This instructs the driver to use EISA or PCI memory-mapped I/O
+ (MMIO) as appropriate instead of programmed I/O ports (PIO).
+ Enabling this gives an improvement in processing time in parts
+ of the driver, but it may cause problems with EISA (DEFEA)
+ adapters. TURBOchannel does not have the concept of I/O ports,
+ so MMIO is always used for these (DEFTA) adapters.
+
+ If unsure, say N.
config SKFP
tristate "SysKonnect FDDI PCI support"
depends on FDDI && PCI
+ select BITREVERSE
---help---
Say Y here if you have a SysKonnect FDDI PCI adapter.
The following adapters are supported by this driver:
which can lead to bad results if the ATM peer loses state and
changes its encapsulation unilaterally.
+config PPPOL2TP
+ tristate "PPP over L2TP (EXPERIMENTAL)"
+ depends on EXPERIMENTAL && PPP
+ help
+ Support for PPP-over-L2TP socket family. L2TP is a protocol
+ used by ISPs and enterprises to tunnel PPP traffic over UDP
+ tunnels. L2TP is replacing PPTP for VPN uses.
+
+ This kernel component handles only L2TP data packets: a
+ userland daemon handles L2TP the control protocol (tunnel
+ and session setup). One such daemon is OpenL2TP
+ (http://openl2tp.sourceforge.net/).
+
config SLIP
tristate "SLIP (serial line) support"
---help---
If you want to log kernel messages over the network, enable this.
See <file:Documentation/networking/netconsole.txt> for details.
-endif #NETDEVICES
-
config NETPOLL
def_bool NETCONSOLE
-config NETPOLL_RX
- bool "Netpoll support for trapping incoming packets"
- default n
- depends on NETPOLL
-
config NETPOLL_TRAP
bool "Netpoll traffic trapping"
default n
config NET_POLL_CONTROLLER
def_bool NETPOLL
-endmenu
+endif # NETDEVICES
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff