To compile this driver as a module, choose M here: the module
will be called macvlan.
+config MACVTAP
+ tristate "MAC-VLAN based tap driver (EXPERIMENTAL)"
+ depends on MACVLAN
+ help
+ This adds a specialized tap character device driver that is based
+ on the MAC-VLAN network interface, called macvtap. A macvtap device
+ can be added in the same way as a macvlan device, using 'type
+ macvlan', and then be accessed through the tap user space interface.
+
+ To compile this driver as a module, choose M here: the module
+ will be called macvtap.
+
config EQUALIZER
tristate "EQL (serial line load balancing) support"
---help---
Set the number of buffer packets used in driver.
config BFIN_MAC_RMII
- bool "RMII PHY Interface (EXPERIMENTAL)"
- depends on BFIN_MAC && EXPERIMENTAL
+ bool "RMII PHY Interface"
+ depends on BFIN_MAC
default y if BFIN527_EZKIT
default n if BFIN537_STAMP
help
select CRC32
select MII
depends on ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || \
- MIPS || BLACKFIN || MN10300
+ MIPS || BLACKFIN || MN10300 || COLDFIRE
help
This is a driver for SMC's 91x series of Ethernet chipsets,
including the SMC91C94 and the SMC91C111. Say Y if you want it
config TI_DAVINCI_EMAC
tristate "TI DaVinci EMAC Support"
- depends on ARM && ARCH_DAVINCI
+ depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 )
select PHYLIB
help
This driver supports TI's DaVinci Ethernet .
help
Say Y here if you want to use the OpenCores 10/100 Mbps Ethernet MAC.
+config GRETH
+ tristate "Aeroflex Gaisler GRETH Ethernet MAC support"
+ depends on SPARC
+ select PHYLIB
+ select CRC32
+ help
+ Say Y here if you want to use the Aeroflex Gaisler GRETH Ethernet MAC.
+
config SMC911X
tristate "SMSC LAN911[5678] support"
select CRC32
config SMSC911X
tristate "SMSC LAN911x/LAN921x families embedded ethernet support"
- depends on ARM || SUPERH || BLACKFIN
+ depends on ARM || SUPERH || BLACKFIN || MIPS
select CRC32
select MII
select PHYLIB
To compile this driver as a module, choose M here. The module
will be called ac3200.
+config KSZ884X_PCI
+ tristate "Micrel KSZ8841/2 PCI"
+ depends on NET_PCI && PCI
+ select MII
+ select CRC32
+ help
+ This PCI driver is for Micrel KSZ8841/KSZ8842 PCI Ethernet chip.
+
+ To compile this driver as a module, choose M here. The module
+ will be called ksz884x.
+
config APRICOT
tristate "Apricot Xen-II on board Ethernet"
depends on NET_PCI && ISA
config FEC
bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
- depends on M523x || M527x || M5272 || M528x || M520x || M532x || MACH_MX27 || ARCH_MX35 || ARCH_MX25
+ depends on M523x || M527x || M5272 || M528x || M520x || M532x || \
+ MACH_MX27 || ARCH_MX35 || ARCH_MX25 || ARCH_MX5
help
Say Y here if you want to use the built-in 10/100 Fast ethernet
controller on some Motorola ColdFire and Freescale i.MX processors.
config XILINX_EMACLITE
tristate "Xilinx 10/100 Ethernet Lite support"
depends on PPC32 || MICROBLAZE
+ select PHYLIB
help
This driver supports the 10/100 Ethernet Lite from Xilinx.
source "drivers/net/fs_enet/Kconfig"
+source "drivers/net/octeon/Kconfig"
+
endif # NET_ETHERNET
#
config GELIC_WIRELESS
bool "PS3 Wireless support"
+ depends on WLAN
depends on GELIC_NET
select WIRELESS_EXT
help
the driver automatically distinguishes the models, you can
safely enable this option even if you have a wireless-less model.
-config GELIC_WIRELESS_OLD_PSK_INTERFACE
- bool "PS3 Wireless private PSK interface (OBSOLETE)"
- depends on GELIC_WIRELESS
- help
- This option retains the obsolete private interface to pass
- the PSK from user space programs to the driver. The PSK
- stands for 'Pre Shared Key' and is used for WPA[2]-PSK
- (WPA-Personal) environment.
- If WPA[2]-PSK is used and you need to use old programs that
- support only this old interface, say Y. Otherwise N.
-
- If unsure, say N.
-
config FSL_PQ_MDIO
tristate "Freescale PQ MDIO"
depends on FSL_SOC
To compile this driver as a module, choose M here: the module
will be called cxgb3.
+config CHELSIO_T4_DEPENDS
+ tristate
+ depends on PCI && INET
+ default y
+
+config CHELSIO_T4
+ tristate "Chelsio Communications T4 Ethernet support"
+ depends on CHELSIO_T4_DEPENDS
+ select FW_LOADER
+ select MDIO
+ help
+ This driver supports Chelsio T4-based gigabit and 10Gb Ethernet
+ adapters.
+
+ For general information about Chelsio and our products, visit
+ our website at <http://www.chelsio.com>.
+
+ For customer support, please visit our customer support page at
+ <http://www.chelsio.com/support.htm>.
+
+ Please send feedback to <linux-bugs@chelsio.com>.
+
+ To compile this driver as a module choose M here; the module
+ will be called cxgb4.
+
config EHEA
tristate "eHEA Ethernet support"
depends on IBMEBUS && INET && SPARSEMEM
If unsure, say N.
+config IXGBEVF
+ tristate "Intel(R) 82599 Virtual Function Ethernet support"
+ depends on PCI_MSI
+ ---help---
+ This driver supports Intel(R) 82599 virtual functions. For more
+ information on how to identify your adapter, go to the Adapter &
+ Driver ID Guide at:
+
+ <http://support.intel.com/support/network/sb/CS-008441.htm>
+
+ For general information and support, go to the Intel support
+ website at:
+
+ <http://support.intel.com>
+
+ More specific information on configuring the driver is in
+ <file:Documentation/networking/ixgbevf.txt>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called ixgbevf. MSI-X interrupt support is required
+ for this driver to work correctly.
+
config IXGB
tristate "Intel(R) PRO/10GbE support"
depends on PCI
config NIU
tristate "Sun Neptune 10Gbit Ethernet support"
depends on PCI
+ select CRC32
help
This enables support for cards based upon Sun's
Neptune chipset.
To compile this driver as a module, choose M here: the module
will be called bnx2x. This is recommended.
+config QLCNIC
+ tristate "QLOGIC QLCNIC 1/10Gb Converged Ethernet NIC Support"
+ depends on PCI
+ help
+ This driver supports QLogic QLE8240 and QLE8242 Converged Ethernet
+ devices.
+
config QLGE
tristate "QLogic QLGE 10Gb Ethernet Driver Support"
depends on PCI
config VMXNET3
tristate "VMware VMXNET3 ethernet driver"
- depends on PCI && X86 && INET
+ depends on PCI && INET
help
This driver supports VMware's vmxnet3 virtual ethernet NIC.
To compile this driver as a module, choose M here: the
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff