# Network device configuration
#
-menu "Network device support"
- depends on NET
-
-config NETDEVICES
+menuconfig NETDEVICES
default y if UML
+ depends on NET
bool "Network device support"
---help---
You can say N here if you don't intend to connect your Linux box to
# that for each of the symbols.
if NETDEVICES
+config NETDEVICES_MULTIQUEUE
+ bool "Netdevice multiple hardware queue support"
+ ---help---
+ Say Y here if you want to allow the network stack to use multiple
+ hardware TX queues on an ethernet device.
+
+ Most people will say N here.
+
config IFB
tristate "Intermediate Functional Block support"
depends on NET_CLS_ACT
To compile this driver as a module, choose M here: the module
will be called bonding.
+config MACVLAN
+ tristate "MAC-VLAN support (EXPERIMENTAL)"
+ depends on EXPERIMENTAL
+ ---help---
+ This allows one to create virtual interfaces that map packets to
+ or from specific MAC addresses to a particular interface.
+
+ To compile this driver as a module, choose M here: the module
+ will be called macvlan.
+
config EQUALIZER
tristate "EQL (serial line load balancing) support"
---help---
If you don't know what to use this for, you don't need it.
+config VETH
+ tristate "Virtual ethernet pair device"
+ ---help---
+ This device is a local ethernet tunnel. Devices are created in pairs.
+ When one end receives the packet it appears on its pair and vice
+ versa.
+
config NET_SB1000
tristate "General Instruments Surfboard 1000"
depends on PNP
If you don't have this card, of course say N.
+config IP1000
+ tristate "IP1000 Gigabit Ethernet support"
+ depends on PCI && EXPERIMENTAL
+ select MII
+ ---help---
+ This driver supports IP1000 gigabit Ethernet cards.
+
+ To compile this driver as a module, choose M here: the module
+ will be called ipg. This is recommended.
+
source "drivers/net/arcnet/Kconfig"
source "drivers/net/phy/Kconfig"
# Ethernet
#
-menu "Ethernet (10 or 100Mbit)"
- depends on !UML
-
-config NET_ETHERNET
+menuconfig NET_ETHERNET
bool "Ethernet (10 or 100Mbit)"
+ depends on !UML
---help---
Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common
type of Local Area Network (LAN) in universities and companies.
kernel: saying N will just cause the configurator to skip all
the questions about Ethernet network cards. If unsure, say N.
+if NET_ETHERNET
+
config MII
tristate "Generic Media Independent Interface device support"
- depends on NET_ETHERNET
help
Most ethernet controllers have MII transceiver either as an external
or internal device. It is safe to say Y or M here even if your
config MACB
tristate "Atmel MACB support"
- depends on NET_ETHERNET && (AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263)
- select MII
+ depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263
+ select PHYLIB
help
The Atmel MACB ethernet interface is found on many AT32 and AT91
parts. Say Y to include support for the MACB chip.
source "drivers/net/arm/Kconfig"
+config AX88796
+ tristate "ASIX AX88796 NE2000 clone support"
+ depends on ARM || MIPS || SUPERH
+ select CRC32
+ select MII
+ help
+ AX88796 driver, using platform bus to provide
+ chip detection and resources
+
+config AX88796_93CX6
+ bool "ASIX AX88796 external 93CX6 eeprom support"
+ depends on AX88796
+ select EEPROM_93CX6
+ help
+ Select this if your platform comes with an external 93CX6 eeprom.
+
config MACE
tristate "MACE (Power Mac ethernet) support"
- depends on NET_ETHERNET && PPC_PMAC && PPC32
+ depends on PPC_PMAC && PPC32
select CRC32
help
Power Macintoshes and clones with Ethernet built-in on the
config BMAC
tristate "BMAC (G3 ethernet) support"
- depends on NET_ETHERNET && PPC_PMAC && PPC32
+ depends on PPC_PMAC && PPC32
select CRC32
help
Say Y for support of BMAC Ethernet interfaces. These are used on G3
config ARIADNE
tristate "Ariadne support"
- depends on NET_ETHERNET && ZORRO
+ depends on ZORRO
help
If you have a Village Tronic Ariadne Ethernet adapter, say Y.
Otherwise, say N.
config A2065
tristate "A2065 support"
- depends on NET_ETHERNET && ZORRO
+ depends on ZORRO
select CRC32
help
If you have a Commodore A2065 Ethernet adapter, say Y. Otherwise,
config HYDRA
tristate "Hydra support"
- depends on NET_ETHERNET && ZORRO
+ depends on ZORRO
select CRC32
help
If you have a Hydra Ethernet adapter, say Y. Otherwise, say N.
config ZORRO8390
tristate "Zorro NS8390-based Ethernet support"
- depends on NET_ETHERNET && ZORRO
+ depends on ZORRO
select CRC32
help
This driver is for Zorro Ethernet cards using an NS8390-compatible
config APNE
tristate "PCMCIA NE2000 support"
- depends on NET_ETHERNET && AMIGA_PCMCIA
+ depends on AMIGA_PCMCIA
select CRC32
help
If you have a PCMCIA NE2000 compatible adapter, say Y. Otherwise,
config APOLLO_ELPLUS
tristate "Apollo 3c505 support"
- depends on NET_ETHERNET && APOLLO
+ depends on APOLLO
help
Say Y or M here if your Apollo has a 3Com 3c505 ISA Ethernet card.
If you don't have one made for Apollos, you can use one from a PC,
config MAC8390
bool "Macintosh NS 8390 based ethernet cards"
- depends on NET_ETHERNET && MAC
+ depends on MAC
select CRC32
help
If you want to include a driver to support Nubus or LC-PDS
config MAC89x0
tristate "Macintosh CS89x0 based ethernet cards"
- depends on NET_ETHERNET && MAC
+ depends on MAC
---help---
Support for CS89x0 chipset based Ethernet cards. If you have a
Nubus or LC-PDS network (Ethernet) card of this type, say Y and
read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. This module will
+ To compile this driver as a module, choose M here. This module will
be called mac89x0.
config MACSONIC
tristate "Macintosh SONIC based ethernet (onboard, NuBus, LC, CS)"
- depends on NET_ETHERNET && MAC
+ depends on MAC
---help---
Support for NatSemi SONIC based Ethernet devices. This includes
the onboard Ethernet in many Quadras as well as some LC-PDS,
one of these say Y and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. This module will
+ To compile this driver as a module, choose M here. This module will
be called macsonic.
config MACMACE
bool "Macintosh (AV) onboard MACE ethernet"
- depends on NET_ETHERNET && MAC
+ depends on MAC
select CRC32
help
Support for the onboard AMD 79C940 MACE Ethernet controller used in
config MVME147_NET
tristate "MVME147 (Lance) Ethernet support"
- depends on NET_ETHERNET && MVME147
+ depends on MVME147
select CRC32
help
Support for the on-board Ethernet interface on the Motorola MVME147
config MVME16x_NET
tristate "MVME16x Ethernet support"
- depends on NET_ETHERNET && MVME16x
+ depends on MVME16x
help
This is the driver for the Ethernet interface on the Motorola
MVME162, 166, 167, 172 and 177 boards. Say Y here to include the
config BVME6000_NET
tristate "BVME6000 Ethernet support"
- depends on NET_ETHERNET && BVME6000
+ depends on BVME6000
help
This is the driver for the Ethernet interface on BVME4000 and
BVME6000 VME boards. Say Y here to include the driver for this chip
config ATARILANCE
tristate "Atari Lance support"
- depends on NET_ETHERNET && ATARI
+ depends on ATARI
help
Say Y to include support for several Atari Ethernet adapters based
on the AMD Lance chipset: RieblCard (with or without battery), or
PAMCard VME (also the version by Rhotron, with different addresses).
-config ATARI_BIONET
- tristate "BioNet-100 support"
- depends on NET_ETHERNET && ATARI && ATARI_ACSI && BROKEN
- help
- Say Y to include support for BioData's BioNet-100 Ethernet adapter
- for the ACSI port. The driver works (has to work...) with a polled
- I/O scheme, so it's rather slow :-(
-
-config ATARI_PAMSNET
- tristate "PAMsNet support"
- depends on NET_ETHERNET && ATARI && ATARI_ACSI && BROKEN
- help
- Say Y to include support for the PAMsNet Ethernet adapter for the
- ACSI port ("ACSI node"). The driver works (has to work...) with a
- polled I/O scheme, so it's rather slow :-(
-
config SUN3LANCE
tristate "Sun3/Sun3x on-board LANCE support"
- depends on NET_ETHERNET && (SUN3 || SUN3X)
+ depends on SUN3 || SUN3X
help
Most Sun3 and Sun3x motherboards (including the 3/50, 3/60 and 3/80)
featured an AMD Lance 10Mbit Ethernet controller on board; say Y
config SUN3_82586
bool "Sun3 on-board Intel 82586 support"
- depends on NET_ETHERNET && SUN3
+ depends on SUN3
help
This driver enables support for the on-board Intel 82586 based
Ethernet adapter found on Sun 3/1xx and 3/2xx motherboards. Note
config HPLANCE
bool "HP on-board LANCE support"
- depends on NET_ETHERNET && DIO
+ depends on DIO
select CRC32
help
If you want to use the builtin "LANCE" Ethernet controller on an
config LASI_82596
tristate "Lasi ethernet"
- depends on NET_ETHERNET && GSC
+ depends on GSC
help
Say Y here to support the builtin Intel 82596 ethernet controller
found in Hewlett-Packard PA-RISC machines with 10Mbit ethernet.
+config SNI_82596
+ tristate "SNI RM ethernet"
+ depends on NET_ETHERNET && SNI_RM
+ help
+ Say Y here to support the on-board Intel 82596 ethernet controller
+ built into SNI RM machines.
+
config MIPS_JAZZ_SONIC
tristate "MIPS JAZZ onboard SONIC Ethernet support"
- depends on NET_ETHERNET && MACH_JAZZ
+ depends on MACH_JAZZ
help
This is the driver for the onboard card of MIPS Magnum 4000,
Acer PICA, Olivetti M700-10 and a few other identical OEM systems.
config MIPS_AU1X00_ENET
bool "MIPS AU1000 Ethernet support"
- depends on NET_ETHERNET && SOC_AU1X00
+ depends on SOC_AU1X00
select PHYLIB
select CRC32
help
If you have an Alchemy Semi AU1X00 based system
say Y. Otherwise, say N.
-config NET_SB1250_MAC
- tristate "SB1250 Ethernet support"
- depends on NET_ETHERNET && SIBYTE_SB1xxx_SOC
-
config SGI_IOC3_ETH
bool "SGI IOC3 Ethernet"
- depends on NET_ETHERNET && PCI && SGI_IP27
+ depends on PCI && SGI_IP27
select CRC32
select MII
help
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
-config SGI_IOC3_ETH_HW_RX_CSUM
- bool "Receive hardware checksums"
- depends on SGI_IOC3_ETH && INET
- default y
- help
- The SGI IOC3 network adapter supports TCP and UDP checksums in
- hardware to offload processing of these checksums from the CPU. At
- the moment only acceleration of IPv4 is supported. This option
- enables offloading for checksums on receive. If unsure, say Y.
-
-config SGI_IOC3_ETH_HW_TX_CSUM
- bool "Transmit hardware checksums"
- depends on SGI_IOC3_ETH && INET
- default y
- help
- The SGI IOC3 network adapter supports TCP and UDP checksums in
- hardware to offload processing of these checksums from the CPU. At
- the moment only acceleration of IPv4 is supported. This option
- enables offloading for checksums on transmit. If unsure, say Y.
-
config MIPS_SIM_NET
tristate "MIPS simulator Network device"
- depends on NET_ETHERNET && MIPS_SIM
+ depends on MIPS_SIM
help
The MIPSNET device is a simple Ethernet network device which is
emulated by the MIPS Simulator.
config SGI_O2MACE_ETH
tristate "SGI O2 MACE Fast Ethernet support"
- depends on NET_ETHERNET && SGI_IP32=y
+ depends on SGI_IP32=y
config STNIC
tristate "National DP83902AV support"
- depends on NET_ETHERNET && SUPERH
+ depends on SUPERH
select CRC32
help
Support for cards based on the National Semiconductor DP83902AV
config SUNLANCE
tristate "Sun LANCE support"
- depends on NET_ETHERNET && SBUS
+ depends on SBUS
select CRC32
help
This driver supports the "le" interface present on all 32-bit Sparc
config HAPPYMEAL
tristate "Sun Happy Meal 10/100baseT support"
- depends on NET_ETHERNET && (SBUS || PCI)
+ depends on SBUS || PCI
select CRC32
help
This driver supports the "hme" interface present on most Ultra
config SUNBMAC
tristate "Sun BigMAC 10/100baseT support (EXPERIMENTAL)"
- depends on NET_ETHERNET && SBUS && EXPERIMENTAL
+ depends on SBUS && EXPERIMENTAL
select CRC32
help
This driver supports the "be" interface available as an Sbus option.
config SUNQE
tristate "Sun QuadEthernet support"
- depends on NET_ETHERNET && SBUS
+ depends on SBUS
select CRC32
help
This driver supports the "qe" 10baseT Ethernet device, available as
config SUNGEM
tristate "Sun GEM support"
- depends on NET_ETHERNET && PCI
+ depends on PCI
select CRC32
help
Support for the Sun GEM chip, aka Sun GigabitEthernet/P 2.0. See also
config CASSINI
tristate "Sun Cassini support"
- depends on NET_ETHERNET && PCI
+ depends on PCI
select CRC32
help
Support for the Sun Cassini chip, aka Sun GigaSwift Ethernet. See also
<http://www.sun.com/products-n-solutions/hardware/docs/pdf/817-4341-10.pdf>
+config SUNVNET
+ tristate "Sun Virtual Network support"
+ depends on SUN_LDOMS
+ help
+ Support for virtual network devices under Sun Logical Domains.
+
config NET_VENDOR_3COM
bool "3COM cards"
- depends on NET_ETHERNET && (ISA || EISA || MCA || PCI)
+ depends on ISA || EISA || MCA || PCI
help
If you have a network (Ethernet) card belonging to this class, say Y
and read the Ethernet-HOWTO, available from
have problems. Some people suggest to ping ("man ping") a nearby
machine every minute ("man cron") when using this card.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called 3c501.
config EL2
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called 3c503.
config ELPLUS
this type, say Y and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called 3c505.
config EL16
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called 3c507.
config EL3
setup disk to disable Plug & Play mode, and to select the default
media type.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called 3c509.
config 3C515
network card, say Y and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called 3c515.
config ELMC
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called 3c523.
config ELMC_II
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called 3c527.
config VORTEX
<file:Documentation/networking/vortex.txt> and in the comments at
the beginning of <file:drivers/net/3c59x.c>.
- To compile this support as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>.
+ To compile this support as a module, choose M here.
config TYPHOON
tristate "3cr990 series \"Typhoon\" support"
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called typhoon.
config LANCE
tristate "AMD LANCE and PCnet (AT1500 and NE2100) support"
- depends on NET_ETHERNET && ISA && ISA_DMA_API
+ depends on ISA && ISA_DMA_API
help
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
config NET_VENDOR_SMC
bool "Western Digital/SMC cards"
- depends on NET_ETHERNET && (ISA || MCA || EISA || MAC)
+ depends on ISA || MCA || EISA || MAC
help
If you have a network (Ethernet) card belonging to this class, say Y
and read the Ethernet-HOWTO, available from
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called wd.
config ULTRAMCA
an MCA based system (PS/2), say Y and read the Ethernet-HOWTO,
available from <http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called smc-mca.
config ULTRA
this but keep it in mind if you have such a SCSI card and have
problems.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called smc-ultra.
config ULTRA32
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called smc-ultra32.
-config SMC91X
- tristate "SMC 91C9x/91C1xxx support"
+config BFIN_MAC
+ tristate "Blackfin 536/537 on-chip mac support"
+ depends on NET_ETHERNET && (BF537 || BF536) && (!BF537_PORT_H)
select CRC32
select MII
- depends on NET_ETHERNET && (ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || SOC_AU1X00 || BFIN)
+ select PHYLIB
+ select BFIN_MAC_USE_L1 if DMA_UNCACHED_NONE
help
- This is a driver for SMC's 91x series of Ethernet chipsets,
- including the SMC91C94 and the SMC91C111. Say Y if you want it
- compiled into the kernel, and read the file
- <file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO,
- available from <http://www.linuxdoc.org/docs.html#howto>.
+ This is the driver for blackfin on-chip mac device. Say Y if you want it
+ compiled into the kernel. This driver is also available as a module
+ ( = code which can be inserted in and removed from the running kernel
+ whenever you want). The module will be called bfin_mac.
- This driver is also available as a module ( = code which can be
- inserted in and removed from the running kernel whenever you want).
- The module will be called smc91x. If you want to compile it as a
- module, say M here and read <file:Documentation/kbuild/modules.txt>
- as well as <file:Documentation/networking/net-modules.txt>.
+config BFIN_MAC_USE_L1
+ bool "Use L1 memory for rx/tx packets"
+ depends on BFIN_MAC && BF537
+ default y
+ help
+ To get maximum network performance, you should use L1 memory as rx/tx buffers.
+ Say N here if you want to reserve L1 memory for other uses.
+
+config BFIN_TX_DESC_NUM
+ int "Number of transmit buffer packets"
+ depends on BFIN_MAC
+ range 6 10 if BFIN_MAC_USE_L1
+ range 10 100
+ default "10"
+ help
+ Set the number of buffer packets used in driver.
+
+config BFIN_RX_DESC_NUM
+ int "Number of receive buffer packets"
+ depends on BFIN_MAC
+ range 20 100 if BFIN_MAC_USE_L1
+ range 20 800
+ default "20"
+ help
+ Set the number of buffer packets used in driver.
+
+config BFIN_MAC_RMII
+ bool "RMII PHY Interface (EXPERIMENTAL)"
+ depends on BFIN_MAC && EXPERIMENTAL
+ default n
+ help
+ Use Reduced PHY MII Interface
config SMC9194
tristate "SMC 9194 support"
<file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO,
available from <http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called smc9194.
+config SMC91X
+ tristate "SMC 91C9x/91C1xxx support"
+ select CRC32
+ select MII
+ depends on ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || SOC_AU1X00 || BLACKFIN
+ help
+ This is a driver for SMC's 91x series of Ethernet chipsets,
+ including the SMC91C94 and the SMC91C111. Say Y if you want it
+ compiled into the kernel, and read the file
+ <file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO,
+ available from <http://www.linuxdoc.org/docs.html#howto>.
+
+ This driver is also available as a module ( = code which can be
+ inserted in and removed from the running kernel whenever you want).
+ The module will be called smc91x. If you want to compile it as a
+ module, say M here and read <file:Documentation/kbuild/modules.txt>.
+
config NET_NETX
tristate "NetX Ethernet support"
select MII
- depends on NET_ETHERNET && ARCH_NETX
+ depends on ARCH_NETX
help
This is support for the Hilscher netX builtin Ethernet ports
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called netx-eth.
config DM9000
tristate "DM9000 support"
- depends on (ARM || MIPS) && NET_ETHERNET
+ depends on ARM || BLACKFIN || MIPS
select CRC32
select MII
---help---
Support for DM9000 chipset.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module will be
- called dm9000.
+ To compile this driver as a module, choose M here. The module
+ will be called dm9000.
config SMC911X
tristate "SMSC LAN911[5678] support"
select CRC32
select MII
- depends on NET_ETHERNET && ARCH_PXA
+ depends on ARCH_PXA || SH_MAGIC_PANEL_R2
help
This is a driver for SMSC's LAN911x series of Ethernet chipsets
including the new LAN9115, LAN9116, LAN9117, and LAN9118.
config NET_VENDOR_RACAL
bool "Racal-Interlan (Micom) NI cards"
- depends on NET_ETHERNET && ISA
+ depends on ISA
help
If you have a network (Ethernet) card belonging to this class, such
as the NI5010, NI5210 or NI6210, say Y and read the Ethernet-HOWTO,
<http://www.tldp.org/docs.html#howto>. Note that this is still
experimental code.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called ni5010.
config NI52
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called ni52.
config NI65
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called ni65.
source "drivers/net/tulip/Kconfig"
config AT1700
tristate "AT1700/1720 support (EXPERIMENTAL)"
- depends on NET_ETHERNET && (ISA || MCA_LEGACY) && EXPERIMENTAL
+ depends on (ISA || MCA_LEGACY) && EXPERIMENTAL
select CRC32
---help---
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called at1700.
config DEPCA
tristate "DEPCA, DE10x, DE200, DE201, DE202, DE422 support"
- depends on NET_ETHERNET && (ISA || EISA || MCA)
+ depends on ISA || EISA || MCA
select CRC32
---help---
If you have a network (Ethernet) card of this type, say Y and read
<http://www.tldp.org/docs.html#howto> as well as
<file:drivers/net/depca.c>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called depca.
config HP100
tristate "HP 10/100VG PCLAN (ISA, EISA, PCI) support"
- depends on NET_ETHERNET && (ISA || EISA || PCI)
+ depends on ISA || EISA || PCI
help
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called hp100.
config NET_ISA
bool "Other ISA cards"
- depends on NET_ETHERNET && ISA
+ depends on ISA
---help---
If your network (Ethernet) card hasn't been mentioned yet and its
bus system (that's the way the cards talks to the other components
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called e2100.
config EWRK3
well as the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called ewrk3.
config EEXPRESS
because the driver was very unreliable. We now have a new driver
that should do better.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called eexpress.
config EEXPRESS_PRO
driver. Please read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called eepro.
config HPLAN_PLUS
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called hp-plus.
config HPLAN
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called hp.
config LP486E
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called eth16i.
config NE2000
laptops), say N here and Y to "NE/2 (ne2000 MCA version) support",
below.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called ne.
config ZNET
is for you, read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called seeq8005.
config NE2_MCA
tristate "NE/2 (ne2000 MCA version) support"
- depends on NET_ETHERNET && MCA_LEGACY
+ depends on MCA_LEGACY
select CRC32
help
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called ne2.
config IBMLANA
tristate "IBM LAN Adapter/A support"
- depends on NET_ETHERNET && MCA && MCA_LEGACY
+ depends on MCA && MCA_LEGACY
---help---
This is a Micro Channel Ethernet adapter. You need to set
CONFIG_MCA to use this driver. It is both available as an in-kernel
driver and as a module.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The only
+ To compile this driver as a module, choose M here. The only
currently supported card is the IBM LAN Adapter/A for Ethernet. It
will both support 16K and 32K memory windows, however a 32K window
gives a better security against packet losses. Usage of multiple
config IBMVETH
tristate "IBM LAN Virtual Ethernet support"
- depends on NET_ETHERNET && PPC_PSERIES
+ depends on PPC_PSERIES
---help---
This driver supports virtual ethernet adapters on newer IBM iSeries
and pSeries systems.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module will
+ To compile this driver as a module, choose M here. The module will
be called ibmveth.
-config IBM_EMAC
- tristate "PowerPC 4xx on-chip Ethernet support"
- depends on 4xx
- help
- This driver supports the PowerPC 4xx EMAC family of on-chip
- Ethernet controllers.
-
-config IBM_EMAC_RXB
- int "Number of receive buffers"
- depends on IBM_EMAC
- default "128"
-
-config IBM_EMAC_TXB
- int "Number of transmit buffers"
- depends on IBM_EMAC
- default "64"
-
-config IBM_EMAC_POLL_WEIGHT
- int "MAL NAPI polling weight"
- depends on IBM_EMAC
- default "32"
-
-config IBM_EMAC_RX_COPY_THRESHOLD
- int "RX skb copy threshold (bytes)"
- depends on IBM_EMAC
- default "256"
-
-config IBM_EMAC_RX_SKB_HEADROOM
- int "Additional RX skb headroom (bytes)"
- depends on IBM_EMAC
- default "0"
- help
- Additional receive skb headroom. Note, that driver
- will always reserve at least 2 bytes to make IP header
- aligned, so usually there is no need to add any additional
- headroom.
-
- If unsure, set to 0.
-
-config IBM_EMAC_PHY_RX_CLK_FIX
- bool "PHY Rx clock workaround"
- depends on IBM_EMAC && (405EP || 440GX || 440EP || 440GR)
- help
- Enable this if EMAC attached to a PHY which doesn't generate
- RX clock if there is no link, if this is the case, you will
- see "TX disable timeout" or "RX disable timeout" in the system
- log.
-
- If unsure, say N.
-
-config IBM_EMAC_DEBUG
- bool "Debugging"
- depends on IBM_EMAC
- default n
-
-config IBM_EMAC_ZMII
- bool
- depends on IBM_EMAC && (NP405H || NP405L || 44x)
- default y
-
-config IBM_EMAC_RGMII
- bool
- depends on IBM_EMAC && 440GX
- default y
-
-config IBM_EMAC_TAH
- bool
- depends on IBM_EMAC && 440GX
- default y
+source "drivers/net/ibm_emac/Kconfig"
+source "drivers/net/ibm_newemac/Kconfig"
config NET_PCI
bool "EISA, VLB, PCI and on board controllers"
- depends on NET_ETHERNET && (ISA || EISA || PCI)
+ depends on ISA || EISA || PCI
help
This is another class of network cards which attach directly to the
bus. If you have one of those, say Y and read the Ethernet-HOWTO,
answer Y here and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called pcnet32.
config PCNET32_NAPI
deployed on potentially unfriendly networks (e.g. in a firewall),
then say Y here.
- See <file:Documentation/networking/NAPI_HOWTO.txt> for more
- information.
-
If in doubt, say N.
config AMD8111_ETH
answer Y here and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called amd8111e.
+
config AMD8111E_NAPI
- bool "Enable NAPI support"
+ bool "Use RX polling (NAPI)"
depends on AMD8111_ETH
help
NAPI is a new driver API designed to reduce CPU and interrupt load
deployed on potentially unfriendly networks (e.g. in a firewall),
then say Y here.
- See <file:Documentation/networking/NAPI_HOWTO.txt> for more
- information.
-
If in doubt, say N.
config ADAPTEC_STARFIRE
deployed on potentially unfriendly networks (e.g. in a firewall),
then say Y here.
- See <file:Documentation/networking/NAPI_HOWTO.txt> for more
- information.
-
If in doubt, say N.
config AC3200
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called ac3200.
config APRICOT
read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module will be
- called apricot.
+ To compile this driver as a module, choose M here. The module
+ will be called apricot.
config B44
- tristate "Broadcom 4400 ethernet support"
- depends on NET_PCI && PCI
+ tristate "Broadcom 440x/47xx ethernet support"
+ depends on SSB_POSSIBLE
+ select SSB
select MII
help
- If you have a network (Ethernet) controller of this type, say Y and
- read the Ethernet-HOWTO, available from
+ If you have a network (Ethernet) controller of this type, say Y
+ or M and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module will be
- called b44.
+ To compile this driver as a module, choose M here. The module
+ will be called b44.
+
+# Auto-select SSB PCI-HOST support, if possible
+config B44_PCI_AUTOSELECT
+ bool
+ depends on B44 && SSB_PCIHOST_POSSIBLE
+ select SSB_PCIHOST
+ default y
+
+# Auto-select SSB PCICORE driver, if possible
+config B44_PCICORE_AUTOSELECT
+ bool
+ depends on B44 && SSB_DRIVER_PCICORE_POSSIBLE
+ select SSB_DRIVER_PCICORE
+ default y
+
+config B44_PCI
+ bool
+ depends on B44_PCI_AUTOSELECT && B44_PCICORE_AUTOSELECT
+ default y
config FORCEDETH
tristate "nForce Ethernet support"
read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module will be
- called forcedeth.
+ To compile this driver as a module, choose M here. The module
+ will be called forcedeth.
config FORCEDETH_NAPI
- bool "Use Rx and Tx Polling (NAPI) (EXPERIMENTAL)"
+ bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
depends on FORCEDETH && EXPERIMENTAL
help
NAPI is a new driver API designed to reduce CPU and interrupt load
deployed on potentially unfriendly networks (e.g. in a firewall),
then say Y here.
- See <file:Documentation/networking/NAPI_HOWTO.txt> for more
- information.
-
If in doubt, say N.
config CS89x0
<http://www.tldp.org/docs.html#howto> as well as
<file:Documentation/networking/cs89x0.txt>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module will be
- called cs89x0.
+ To compile this driver as a module, choose M here. The module
+ will be called cs89x0.
config TC35815
tristate "TOSHIBA TC35815 Ethernet support"
depends on NET_PCI && PCI && MIPS
select MII
-config DGRS
- tristate "Digi Intl. RightSwitch SE-X support"
- depends on NET_PCI && (PCI || EISA)
- ---help---
- This is support for the Digi International RightSwitch series of
- PCI/EISA Ethernet switch cards. These include the SE-4 and the SE-6
- models. If you have a network card of this type, say Y and read the
- Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>. More specific
- information is contained in <file:Documentation/networking/dgrs.txt>.
-
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
- will be called dgrs.
-
config EEPRO100
tristate "EtherExpressPro/100 support (eepro100, original Becker driver)"
depends on NET_PCI && PCI
card, say Y and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called eepro100.
More specific information on configuring the driver is in
<file:Documentation/networking/e100.txt>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called e100.
config LNE390
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called lne390.
config FEALNX
NetVin NV5000SC Via 86C926 SureCom NE34 Winbond
Holtek HT80232 Holtek HT80229
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called ne2k-pci.
config NE3210
<http://www.tldp.org/docs.html#howto>. Note that this driver
will NOT WORK for NE3200 cards as they are completely different.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called ne3210.
config ES3210
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called es3210.
config 8139CP
Compaq NetFlex and Olicom cards. Please read the file
<file:Documentation/networking/tlan.txt> for more details.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called tlan.
Please email feedback to <torben.mathiasen@compaq.com>.
deployed on potentially unfriendly networks (e.g. in a firewall),
then say Y here.
- See <file:Documentation/networking/NAPI_HOWTO.txt> for more
- information.
-
config LAN_SAA9730
bool "Philips SAA9730 Ethernet support"
depends on NET_PCI && PCI && MIPS_ATLAS
To compile this driver as a module, choose M here: the module
will be called sc92031. This is recommended.
+config CPMAC
+ tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)"
+ depends on NET_ETHERNET && EXPERIMENTAL && AR7
+ select PHYLIB
+ select FIXED_PHY
+ select FIXED_MII_100_FDX
+ help
+ TI AR7 CPMAC Ethernet support
+
config NET_POCKET
bool "Pocket and portable adapters"
- depends on NET_ETHERNET && PARPORT
+ depends on PARPORT
---help---
Cute little network (Ethernet) devices which attach to the parallel
port ("pocket adapters"), commonly used with laptops. If you have
config SGISEEQ
tristate "SGI Seeq ethernet controller support"
- depends on NET_ETHERNET && SGI_IP22
+ depends on SGI_IP22
help
Say Y here if you have an Seeq based Ethernet network card. This is
used in many Silicon Graphics machines.
config DECLANCE
tristate "DEC LANCE ethernet controller support"
- depends on NET_ETHERNET && MACH_DECSTATION
+ depends on MACH_DECSTATION
select CRC32
help
This driver is for the series of Ethernet controllers produced by
Say Y here if you want to use the second built-in 10/100 Fast
ethernet controller on some Motorola ColdFire processors.
+config FEC_MPC52xx
+ tristate "MPC52xx FEC driver"
+ depends on PPC_MERGE && PPC_MPC52xx && PPC_BESTCOMM_FEC
+ select CRC32
+ select PHYLIB
+ ---help---
+ This option enables support for the MPC5200's on-chip
+ Fast Ethernet Controller
+ If compiled as module, it will be called 'fec_mpc52xx.ko'.
+
+config FEC_MPC52xx_MDIO
+ bool "MPC52xx FEC MDIO bus driver"
+ depends on FEC_MPC52xx
+ default y
+ ---help---
+ The MPC5200's FEC can connect to the Ethernet either with
+ an external MII PHY chip or 10 Mbps 7-wire interface
+ (Motorola? industry standard).
+ If your board uses an external PHY connected to FEC, enable this.
+ If not sure, enable.
+ If compiled as module, it will be called 'fec_mpc52xx_phy.ko'.
+
config NE_H8300
tristate "NE2000 compatible support for H8/300"
- depends on H8300 && NET_ETHERNET
+ depends on H8300
help
Say Y here if you want to use the NE2000 compatible
controller on the Renesas H8/300 processor.
source "drivers/net/fec_8xx/Kconfig"
source "drivers/net/fs_enet/Kconfig"
-endmenu
+endif # NET_ETHERNET
#
# Gigabit Ethernet
bool "Ethernet (1000 Mbit)"
depends on !UML
default y
+ ---help---
+ Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common
+ type of Local Area Network (LAN) in universities and companies.
+
+ Say Y here to get to see options for Gigabit Ethernet drivers.
+ This option alone does not add any kernel code.
+ Note that drivers supporting both 100 and 1000 MBit may be listed
+ under "Ethernet (10 or 100MBit)" instead.
+
+ If you say N, all options in this submenu will be skipped and disabled.
if NETDEV_1000
The safe and default value for this is N.
config DL2K
- tristate "D-Link DL2000-based Gigabit Ethernet support"
+ tristate "DL2000/TC902x-based Gigabit Ethernet support"
depends on PCI
select CRC32
help
- This driver supports D-Link 2000-based gigabit ethernet cards, which
- includes
+ This driver supports DL2000/TC902x-based Gigabit ethernet cards,
+ which includes
D-Link DGE-550T Gigabit Ethernet Adapter.
D-Link DL2000-based Gigabit Ethernet Adapter.
+ Sundance/Tamarack TC902x Gigabit Ethernet Adapter.
To compile this driver as a module, choose M here: the
module will be called dl2k.
More specific information on configuring the driver is in
<file:Documentation/networking/e1000.txt>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called e1000.
config E1000_NAPI
deployed on potentially unfriendly networks (e.g. in a firewall),
then say Y here.
- See <file:Documentation/networking/NAPI_HOWTO.txt> for more
- information.
-
If in doubt, say N.
config E1000_DISABLE_PACKET_SPLIT
If in doubt, say N.
+config E1000E
+ tristate "Intel(R) PRO/1000 PCI-Express Gigabit Ethernet support"
+ depends on PCI
+ ---help---
+ This driver supports the PCI-Express Intel(R) PRO/1000 gigabit
+ ethernet family of adapters. For PCI or PCI-X e1000 adapters,
+ use the regular e1000 driver For more information on how to
+ identify your adapter, go to the Adapter & Driver ID Guide at:
+
+ <http://support.intel.com/support/network/adapter/pro100/21397.htm>
+
+ For general information and support, go to the Intel support
+ website at:
+
+ <http://support.intel.com>
+
+ More specific information on configuring the driver is in
+ <file:Documentation/networking/e1000e.txt>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called e1000e.
+
source "drivers/net/ixp2000/Kconfig"
config MYRI_SBUS
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module will be
+ To compile this driver as a module, choose M here. The module will be
called hamachi.
config YELLOWFIN
will be called r8169. This is recommended.
config R8169_NAPI
- bool "Use Rx and Tx Polling (NAPI) (EXPERIMENTAL)"
+ bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
depends on R8169 && EXPERIMENTAL
help
NAPI is a new driver API designed to reduce CPU and interrupt load
deployed on potentially unfriendly networks (e.g. in a firewall),
then say Y here.
- See <file:Documentation/networking/NAPI_HOWTO.txt> for more
- information.
-
If in doubt, say N.
config R8169_VLAN
If in doubt, say Y.
+config SB1250_MAC
+ tristate "SB1250 Gigabit Ethernet support"
+ depends on SIBYTE_SB1xxx_SOC
+ select PHYLIB
+ ---help---
+ This driver supports Gigabit Ethernet interfaces based on the
+ Broadcom SiByte family of System-On-a-Chip parts. They include
+ the BCM1120, BCM1125, BCM1125H, BCM1250, BCM1255, BCM1280, BCM1455
+ and BCM1480 chips.
+
+ To compile this driver as a module, choose M here: the module
+ will be called sb1250-mac.
+
config SIS190
tristate "SiS190/SiS191 gigabit ethernet support"
depends on PCI
To compile this driver as a module, choose M here: the module
will be called skge. This is recommended.
+config SKGE_DEBUG
+ bool "Debugging interface"
+ depends on SKGE && DEBUG_FS
+ help
+ This option adds the ability to dump driver state for debugging.
+ The file debugfs/skge/ethX displays the state of the internal
+ transmit and receive rings.
+
+ If unsure, say N.
+
config SKY2
- tristate "SysKonnect Yukon2 support (EXPERIMENTAL)"
+ tristate "SysKonnect Yukon2 support"
depends on PCI
select CRC32
---help---
To compile this driver as a module, choose M here: the module
will be called sky2. This is recommended.
+config SKY2_DEBUG
+ bool "Debugging interface"
+ depends on SKY2 && DEBUG_FS
+ help
+ This option adds the ability to dump driver state for debugging.
+ The file debugfs/sky2/ethX displays the state of the internal
+ transmit and receive rings.
+
+ If unsure, say N.
+
config SK98LIN
tristate "Marvell Yukon Chipset / SysKonnect SK-98xx Support (DEPRECATED)"
depends on PCI
config VIA_VELOCITY
tristate "VIA Velocity support"
- depends on NET_PCI && PCI
+ depends on PCI
select CRC32
select CRC_CCITT
select MII
To compile this driver as a module, choose M here: the module
will be called tsi108_eth.
+config GELIC_NET
+ tristate "PS3 Gigabit Ethernet driver"
+ depends on PPC_PS3
+ help
+ This driver supports the network device on the PS3 game
+ console. This driver has built-in support for Ethernet.
+
+ To compile this driver as a module, choose M here: the
+ module will be called ps3_gelic.
+
config GIANFAR
tristate "Gianfar Ethernet"
depends on 85xx || 83xx || PPC_86xx
and MPC86xx family of chips, and the FEC on the 8540.
config GFAR_NAPI
- bool "NAPI Support"
+ bool "Use Rx Polling (NAPI)"
depends on GIANFAR
config UCC_GETH
tristate "Freescale QE Gigabit Ethernet"
depends on QUICC_ENGINE
- select UCC_FAST
+ select PHYLIB
help
This driver supports the Gigabit Ethernet mode of the QUICC Engine,
which is available on some Freescale SOCs.
config UGETH_NAPI
- bool "NAPI Support"
+ bool "Use Rx Polling (NAPI)"
depends on UCC_GETH
config UGETH_MAGIC_PACKET
depends on UCC_GETH
config MV643XX_ETH
- tristate "MV-643XX Ethernet support"
- depends on MOMENCO_OCELOT_C || MOMENCO_JAGUAR_ATX || MV64360 || MOMENCO_OCELOT_3 || (PPC_MULTIPLATFORM && PPC32)
+ tristate "Marvell Discovery (643XX) and Orion ethernet support"
+ depends on MV64360 || MV64X60 || (PPC_MULTIPLATFORM && PPC32) || ARCH_ORION
select MII
help
- This driver supports the gigabit Ethernet on the Marvell MV643XX
- chipset which is used in the Momenco Ocelot C and Jaguar ATX and
- Pegasos II, amongst other PPC and MIPS boards.
+ This driver supports the gigabit ethernet MACs in the
+ Marvell Discovery PPC/MIPS chipset family (MV643XX) and
+ in the Marvell Orion ARM SoC family.
+
+ Some boards that use the Discovery chipset are the Momenco
+ Ocelot C and Jaguar ATX and Pegasos II.
config QLA3XXX
tristate "QLogic QLA3XXX Network Driver Support"
bool "Ethernet (10000 Mbit)"
depends on !UML
default y
+ ---help---
+ Say Y here to get to see options for 10 Gigabit Ethernet drivers.
+ This option alone does not add any kernel code.
+
+ If you say N, all options in this submenu will be skipped and disabled.
if NETDEV_10000
config EHEA
tristate "eHEA Ethernet support"
- depends on IBMEBUS
+ depends on IBMEBUS && INET
+ select INET_LRO
---help---
This driver supports the IBM pSeries eHEA ethernet adapter.
To compile the driver as a module, choose M here. The module
will be called ehea.
+config IXGBE
+ tristate "Intel(R) 10GbE PCI Express adapters support"
+ depends on PCI
+ ---help---
+ This driver supports Intel(R) 10GbE PCI Express family of
+ adapters. For more information on how to identify your adapter, go
+ to the Adapter & Driver ID Guide at:
+
+ <http://support.intel.com/support/network/adapter/pro100/21397.htm>
+
+ For general information and support, go to the Intel support
+ website at:
+
+ <http://support.intel.com>
+
+ More specific information on configuring the driver is in
+ <file:Documentation/networking/ixgbe.txt>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called ixgbe.
+
config IXGB
tristate "Intel(R) PRO/10GbE support"
depends on PCI
---help---
- This driver supports Intel(R) PRO/10GbE family of
- adapters. For more information on how to identify your adapter, go
+ This driver supports Intel(R) PRO/10GbE family of adapters for
+ PCI-X type cards. For PCI-E type cards, use the "ixgbe" driver
+ instead. For more information on how to identify your adapter, go
to the Adapter & Driver ID Guide at:
<http://support.intel.com/support/network/adapter/pro100/21397.htm>
More specific information on configuring the driver is in
<file:Documentation/networking/ixgb.txt>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called ixgb.
config IXGB_NAPI
deployed on potentially unfriendly networks (e.g. in a firewall),
then say Y here.
- See <file:Documentation/networking/NAPI_HOWTO.txt> for more
- information.
-
If in doubt, say N.
config S2IO
deployed on potentially unfriendly networks (e.g. in a firewall),
then say Y here.
- See <file:Documentation/networking/NAPI_HOWTO.txt> for more
- information.
-
If in doubt, say N.
config MYRI10GE
tristate "Myricom Myri-10G Ethernet support"
- depends on PCI
+ depends on PCI && INET
select FW_LOADER
select CRC32
+ select INET_LRO
---help---
This driver supports Myricom Myri-10G Dual Protocol interface in
Ethernet mode. If the eeprom on your board is not recent enough,
<http://www.myri.com/scs/download-Myri10GE.html>
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called myri10ge.
config NETXEN_NIC
help
This enables the support for NetXen's Gigabit Ethernet card.
+config NIU
+ tristate "Sun Neptune 10Gbit Ethernet support"
+ depends on PCI
+ help
+ This enables support for cards based upon Sun's
+ Neptune chipset.
+
config PASEMI_MAC
tristate "PA Semi 1/10Gbit MAC"
depends on PPC64 && PCI
config MLX4_DEBUG
bool "Verbose debugging output" if (MLX4_CORE && EMBEDDED)
+ depends on MLX4_CORE
default y
---help---
This option causes debugging code to be compiled into the
debug_level module parameter (which can also be set after
the driver is loaded through sysfs).
+config TEHUTI
+ tristate "Tehuti Networks 10G Ethernet"
+ depends on PCI
+ select ZLIB_INFLATE
+ help
+ Tehuti Networks 10G Ethernet NIC
+
endif # NETDEV_10000
source "drivers/net/tokenring/Kconfig"
source "drivers/s390/net/Kconfig"
+config XEN_NETDEV_FRONTEND
+ tristate "Xen network device frontend driver"
+ depends on XEN
+ default y
+ help
+ The network device frontend driver allows the kernel to
+ access network devices exported exported by a virtual
+ machine containing a physical network device driver. The
+ frontend driver is intended for unprivileged guest domains;
+ if you are compiling a kernel for a Xen guest, you almost
+ certainly want to enable this.
+
config ISERIES_VETH
tristate "iSeries Virtual Ethernet driver support"
depends on PPC_ISERIES
with the PLIP support in Linux versions 1.0.x. This option enlarges
your kernel by about 8 KB.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module will be
- called plip. If unsure, say Y or M, in case you buy a laptop
- later.
+ To compile this driver as a module, choose M here. The module
+ will be called plip. If unsure, say Y or M, in case you buy
+ a laptop later.
config PPP
tristate "PPP (point-to-point protocol) support"
If you said Y to "Version information on all symbols" above, then
you cannot compile the PPP driver into the kernel; you can then only
compile it as a module. To compile this driver as a module, choose M
- here and read <file:Documentation/networking/net-modules.txt>.
- The module will be called ppp_generic.
+ here. The module will be called ppp_generic.
config PPP_MULTILINK
bool "PPP multilink support (EXPERIMENTAL)"
which can lead to bad results if the ATM peer loses state and
changes its encapsulation unilaterally.
+config PPPOL2TP
+ tristate "PPP over L2TP (EXPERIMENTAL)"
+ depends on EXPERIMENTAL && PPP && INET
+ help
+ Support for PPP-over-L2TP socket family. L2TP is a protocol
+ used by ISPs and enterprises to tunnel PPP traffic over UDP
+ tunnels. L2TP is replacing PPTP for VPN uses.
+
+ This kernel component handles only L2TP data packets: a
+ userland daemon handles L2TP the control protocol (tunnel
+ and session setup). One such daemon is OpenL2TP
+ (http://openl2tp.sourceforge.net/).
+
config SLIP
tristate "SLIP (serial line) support"
---help---
<http://www.bart.nl/~patrickr/term-howto/Term-HOWTO.html>). SLIP
support will enlarge your kernel by about 4 KB. If unsure, say N.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module will be
- called slip.
+ To compile this driver as a module, choose M here. The module
+ will be called slip.
config SLIP_COMPRESSED
bool "CSLIP compressed headers"
If you want to log kernel messages over the network, enable this.
See <file:Documentation/networking/netconsole.txt> for details.
-endif #NETDEVICES
+config NETCONSOLE_DYNAMIC
+ bool "Dynamic reconfiguration of logging targets (EXPERIMENTAL)"
+ depends on NETCONSOLE && SYSFS && EXPERIMENTAL
+ select CONFIGFS_FS
+ help
+ This option enables the ability to dynamically reconfigure target
+ parameters (interface, IP addresses, port numbers, MAC addresses)
+ at runtime through a userspace interface exported using configfs.
+ See <file:Documentation/networking/netconsole.txt> for details.
config NETPOLL
def_bool NETCONSOLE
config NET_POLL_CONTROLLER
def_bool NETPOLL
-endmenu
+config VIRTIO_NET
+ tristate "Virtio network driver (EXPERIMENTAL)"
+ depends on EXPERIMENTAL && VIRTIO
+ ---help---
+ This is the virtual network driver for lguest. Say Y or M.
+
+endif # NETDEVICES
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff