# that for each of the symbols.
if NETDEVICES
+config IFB
+ tristate "Intermediate Functional Block support"
+ depends on NET_CLS_ACT
+ ---help---
+ This is an intermidiate driver that allows sharing of
+ resources.
+ To compile this driver as a module, choose M here: the module
+ will be called ifb. If you want to use more than one ifb
+ device at a time, you need to compile this driver as a module.
+ Instead of 'ifb', the devices will then be called 'ifb0',
+ 'ifb1' etc.
+ Look at the iproute2 documentation directory for usage etc
+
config DUMMY
tristate "Dummy net driver support"
---help---
If you don't have this card, of course say N.
- source "drivers/net/arcnet/Kconfig"
+source "drivers/net/arcnet/Kconfig"
source "drivers/net/phy/Kconfig"
If you're not building a kernel for a Sun 3, say N.
config SUN3_82586
- tristate "Sun3 on-board Intel 82586 support"
+ bool "Sun3 on-board Intel 82586 support"
depends on NET_ETHERNET && SUN3
help
This driver enables support for the on-board Intel 82586 based
config SGI_IOC3_ETH
bool "SGI IOC3 Ethernet"
- depends on NET_ETHERNET && PCI && SGI_IP27 && BROKEN
+ depends on NET_ETHERNET && PCI && SGI_IP27
select CRC32
select MII
help
the moment only acceleration of IPv4 is supported. This option
enables offloading for checksums on transmit. If unsure, say Y.
+config MIPS_SIM_NET
+ tristate "MIPS simulator Network device (EXPERIMENTAL)"
+ depends on NETDEVICES && MIPS_SIM && EXPERIMENTAL
+ help
+ The MIPSNET device is a simple Ethernet network device which is
+ emulated by the MIPS Simulator.
+ If you are not using a MIPSsim or are unsure, say N.
+
config SGI_O2MACE_ETH
tristate "SGI O2 MACE Fast Ethernet support"
depends on NET_ETHERNET && SGI_IP32=y
Support for the Sun GEM chip, aka Sun GigabitEthernet/P 2.0. See also
<http://www.sun.com/products-n-solutions/hardware/docs/pdf/806-3985-10.pdf>.
+config CASSINI
+ tristate "Sun Cassini support"
+ depends on NET_ETHERNET && PCI
+ select CRC32
+ help
+ Support for the Sun Cassini chip, aka Sun GigaSwift Ethernet. See also
+ <http://www.sun.com/products-n-solutions/hardware/docs/pdf/817-4341-10.pdf>
+
config NET_VENDOR_3COM
bool "3COM cards"
depends on NET_ETHERNET && (ISA || EISA || MCA || PCI)
tristate "SMC 91C9x/91C1xxx support"
select CRC32
select MII
- depends on NET_ETHERNET && (ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH)
+ depends on NET_ETHERNET && (ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || SOC_AU1X00)
help
This is a driver for SMC's 91x series of Ethernet chipsets,
including the SMC91C94 and the SMC91C111. Say Y if you want it
config DM9000
tristate "DM9000 support"
- depends on ARM && NET_ETHERNET
+ depends on (ARM || MIPS) && NET_ETHERNET
select CRC32
select MII
---help---
be called ibmveth.
config IBM_EMAC
- bool "IBM PPC4xx EMAC driver support"
+ tristate "PowerPC 4xx on-chip Ethernet support"
depends on 4xx
- select CRC32
- ---help---
- This driver supports the IBM PPC4xx EMAC family of on-chip
- Ethernet controllers.
-
-config IBM_EMAC_ERRMSG
- bool "Verbose error messages"
- depends on IBM_EMAC && BROKEN
+ help
+ This driver supports the PowerPC 4xx EMAC family of on-chip
+ Ethernet controllers.
config IBM_EMAC_RXB
int "Number of receive buffers"
depends on IBM_EMAC
- default "128" if IBM_EMAC4
- default "64"
+ default "128"
config IBM_EMAC_TXB
int "Number of transmit buffers"
depends on IBM_EMAC
- default "128" if IBM_EMAC4
- default "8"
+ default "64"
+
+config IBM_EMAC_POLL_WEIGHT
+ int "MAL NAPI polling weight"
+ depends on IBM_EMAC
+ default "32"
-config IBM_EMAC_FGAP
- int "Frame gap"
+config IBM_EMAC_RX_COPY_THRESHOLD
+ int "RX skb copy threshold (bytes)"
depends on IBM_EMAC
- default "8"
+ default "256"
-config IBM_EMAC_SKBRES
- int "Skb reserve amount"
+config IBM_EMAC_RX_SKB_HEADROOM
+ int "Additional RX skb headroom (bytes)"
depends on IBM_EMAC
default "0"
+ help
+ Additional receive skb headroom. Note, that driver
+ will always reserve at least 2 bytes to make IP header
+ aligned, so usualy there is no need to add any additional
+ headroom.
+
+ If unsure, set to 0.
+
+config IBM_EMAC_PHY_RX_CLK_FIX
+ bool "PHY Rx clock workaround"
+ depends on IBM_EMAC && (405EP || 440GX || 440EP || 440GR)
+ help
+ Enable this if EMAC attached to a PHY which doesn't generate
+ RX clock if there is no link, if this is the case, you will
+ see "TX disable timeout" or "RX disable timeout" in the system
+ log.
+
+ If unsure, say N.
+
+config IBM_EMAC_DEBUG
+ bool "Debugging"
+ depends on IBM_EMAC
+ default n
+
+config IBM_EMAC_ZMII
+ bool
+ depends on IBM_EMAC && (NP405H || NP405L || 44x)
+ default y
+
+config IBM_EMAC_RGMII
+ bool
+ depends on IBM_EMAC && 440GX
+ default y
+
+config IBM_EMAC_TAH
+ bool
+ depends on IBM_EMAC && 440GX
+ default y
config NET_PCI
bool "EISA, VLB, PCI and on board controllers"
config CS89x0
tristate "CS89x0 support"
- depends on (NET_PCI && (ISA || ARCH_IXDP2X01)) || ARCH_PNX0105
+ depends on NET_PCI && (ISA || ARCH_IXDP2X01 || ARCH_PNX010X)
---help---
Support for CS89x0 chipset based Ethernet cards. If you have a
network (Ethernet) card of this type, say Y and read the
To compile this driver as a module, choose M here and read
<file:Documentation/networking/net-modules.txt>. The module will be
- called cs89x.
+ called cs89x0.
config TC35815
tristate "TOSHIBA TC35815 Ethernet support"
config NET_POCKET
bool "Pocket and portable adapters"
- depends on NET_ETHERNET && ISA
+ depends on NET_ETHERNET && PARPORT
---help---
Cute little network (Ethernet) devices which attach to the parallel
port ("pocket adapters"), commonly used with laptops. If you have
config ATP
tristate "AT-LAN-TEC/RealTek pocket adapter support"
- depends on NET_POCKET && ISA && X86
+ depends on NET_POCKET && PARPORT && X86
select CRC32
---help---
This is a network (Ethernet) device which attaches to your parallel
config DE600
tristate "D-Link DE600 pocket adapter support"
- depends on NET_POCKET && ISA
+ depends on NET_POCKET && PARPORT
---help---
This is a network (Ethernet) device which attaches to your parallel
port. Read <file:Documentation/networking/DLINK.txt> as well as the
config DE620
tristate "D-Link DE620 pocket adapter support"
- depends on NET_POCKET && ISA
+ depends on NET_POCKET && PARPORT
---help---
This is a network (Ethernet) device which attaches to your parallel
port. Read <file:Documentation/networking/DLINK.txt> as well as the
the Motorola 68360 processor.
config FEC
- bool "FEC ethernet controller (of ColdFire 5272)"
- depends on M5272 || M5282
+ bool "FEC ethernet controller (of ColdFire CPUs)"
+ depends on M523x || M527x || M5272 || M528x || M520x
help
Say Y here if you want to use the built-in 10/100 Fast ethernet
- controller on the Motorola ColdFire 5272 processor.
+ controller on some Motorola ColdFire processors.
+
+config FEC2
+ bool "Second FEC ethernet controller (on some ColdFire CPUs)"
+ depends on FEC
+ help
+ Say Y here if you want to use the second built-in 10/100 Fast
+ ethernet controller on some Motorola ColdFire processors.
config NE_H8300
tristate "NE2000 compatible support for H8/300"
controller on the Renesas H8/300 processor.
source "drivers/net/fec_8xx/Kconfig"
+source "drivers/net/fs_enet/Kconfig"
endmenu
If in doubt, say N.
+source "drivers/net/ixp2000/Kconfig"
+
config MYRI_SBUS
tristate "MyriCOM Gigabit Ethernet support"
depends on SBUS
If in doubt, say Y.
config SIS190
- tristate "SiS190 gigabit ethernet support"
+ tristate "SiS190/SiS191 gigabit ethernet support"
depends on PCI
select CRC32
select MII
---help---
- Say Y here if you have a SiS 190 PCI Gigabit Ethernet adapter.
+ Say Y here if you have a SiS 190 PCI Fast Ethernet adapter or
+ a SiS 191 PCI Gigabit Ethernet adapter. Both are expected to
+ appear in lan on motherboard designs which are based on SiS 965
+ and SiS 966 south bridge.
To compile this driver as a module, choose M here: the module
will be called sis190. This is recommended.
---help---
This driver support the Marvell Yukon or SysKonnect SK-98xx/SK-95xx
and related Gigabit Ethernet adapters. It is a new smaller driver
- driver with better performance and more complete ethtool support.
+ with better performance and more complete ethtool support.
It does not support the link failover and network management
features that "portable" vendor supplied sk98lin driver does.
-
+
+
+config SKY2
+ tristate "SysKonnect Yukon2 support (EXPERIMENTAL)"
+ depends on PCI && EXPERIMENTAL
+ select CRC32
+ ---help---
+ This driver support the Marvell Yukon 2 Gigabit Ethernet adapter.
+
+ To compile this driver as a module, choose M here: the module
+ will be called sky2. This is recommended.
+
config SK98LIN
tristate "Marvell Yukon Chipset / SysKonnect SK-98xx Support"
depends on PCI
To compile this driver as a module, choose M here: the module
will be called bnx2. This is recommended.
+config SPIDER_NET
+ tristate "Spider Gigabit Ethernet driver"
+ depends on PCI && PPC_CELL
+ help
+ This driver supports the Gigabit Ethernet chips present on the
+ Cell Processor-Based Blades from IBM.
+
config GIANFAR
tristate "Gianfar Ethernet"
depends on 85xx || 83xx
+ select PHYLIB
help
This driver supports the Gigabit TSEC on the MPC85xx
family of chips, and the FEC on the 8540
depends on PCI
---help---
This driver supports the 10Gbe XFrame NIC of S2IO.
- For help regarding driver compilation, installation and
- tuning please look into ~/drivers/net/s2io/README.txt.
+ More specific information on configuring the driver is in
+ <file:Documentation/networking/s2io.txt>.
config S2IO_NAPI
bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
If in doubt, say N.
-config 2BUFF_MODE
- bool "Use 2 Buffer Mode on Rx side."
- depends on S2IO
- ---help---
- On enabling the 2 buffer mode, the received frame will be
- split into 2 parts before being DMA'ed to the hosts memory.
- The parts are the ethernet header and ethernet payload.
- This is useful on systems where DMA'ing to to unaligned
- physical memory loactions comes with a heavy price.
- If not sure please say N.
-
endmenu
if !UML
tristate "iSeries Virtual Ethernet driver support"
depends on PPC_ISERIES
+config RIONET
+ tristate "RapidIO Ethernet over messaging driver support"
+ depends on NETDEVICES && RAPIDIO
+
+config RIONET_TX_SIZE
+ int "Number of outbound queue entries"
+ depends on RIONET
+ default "128"
+
+config RIONET_RX_SIZE
+ int "Number of inbound queue entries"
+ depends on RIONET
+ default "128"
+
config FDDI
bool "FDDI driver support"
depends on (PCI || EISA)
module; it is called bsd_comp and will show up in the directory
modules once you have said "make modules". If unsure, say N.
+config PPP_MPPE
+ tristate "PPP MPPE compression (encryption) (EXPERIMENTAL)"
+ depends on PPP && EXPERIMENTAL
+ select CRYPTO
+ select CRYPTO_SHA1
+ select CRYPTO_ARC4
+ ---help---
+ Support for the MPPE Encryption protocol, as employed by the
+ Microsoft Point-to-Point Tunneling Protocol.
+
+ See http://pptpclient.sourceforge.net/ for information on
+ configuring PPTP clients and servers to utilize this method.
+
config PPPOE
tristate "PPP over Ethernet (EXPERIMENTAL)"
depends on EXPERIMENTAL && PPP
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff