# that for each of the symbols.
if NETDEVICES
+config IFB
+ tristate "Intermediate Functional Block support"
+ depends on NET_CLS_ACT
+ ---help---
+ This is an intermidiate driver that allows sharing of
+ resources.
+ To compile this driver as a module, choose M here: the module
+ will be called ifb. If you want to use more than one ifb
+ device at a time, you need to compile this driver as a module.
+ Instead of 'ifb', the devices will then be called 'ifb0',
+ 'ifb1' etc.
+ Look at the iproute2 documentation directory for usage etc
+
config DUMMY
tristate "Dummy net driver support"
---help---
If you don't have this card, of course say N.
- source "drivers/net/arcnet/Kconfig"
+source "drivers/net/arcnet/Kconfig"
source "drivers/net/phy/Kconfig"
config SGI_IOC3_ETH
bool "SGI IOC3 Ethernet"
- depends on NET_ETHERNET && PCI && SGI_IP27 && BROKEN
+ depends on NET_ETHERNET && PCI && SGI_IP27
select CRC32
select MII
help
tristate "SMC 91C9x/91C1xxx support"
select CRC32
select MII
- depends on NET_ETHERNET && (ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH)
+ depends on NET_ETHERNET && (ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || SOC_AU1X00)
help
This is a driver for SMC's 91x series of Ethernet chipsets,
including the SMC91C94 and the SMC91C111. Say Y if you want it
config DM9000
tristate "DM9000 support"
- depends on ARM && NET_ETHERNET
+ depends on (ARM || MIPS) && NET_ETHERNET
select CRC32
select MII
---help---
config CS89x0
tristate "CS89x0 support"
- depends on (NET_PCI && (ISA || ARCH_IXDP2X01)) || ARCH_PNX0105
+ depends on NET_PCI && (ISA || ARCH_IXDP2X01 || ARCH_PNX010X)
---help---
Support for CS89x0 chipset based Ethernet cards. If you have a
network (Ethernet) card of this type, say Y and read the
To compile this driver as a module, choose M here and read
<file:Documentation/networking/net-modules.txt>. The module will be
- called cs89x.
+ called cs89x0.
config TC35815
tristate "TOSHIBA TC35815 Ethernet support"
config FEC
bool "FEC ethernet controller (of ColdFire CPUs)"
- depends on M523x || M527x || M5272 || M528x
+ depends on M523x || M527x || M5272 || M528x || M520x
help
Say Y here if you want to use the built-in 10/100 Fast ethernet
controller on some Motorola ColdFire processors.
If in doubt, say N.
+source "drivers/net/ixp2000/Kconfig"
+
config MYRI_SBUS
tristate "MyriCOM Gigabit Ethernet support"
depends on SBUS
It does not support the link failover and network management
features that "portable" vendor supplied sk98lin driver does.
-
+
+
+config SKY2
+ tristate "SysKonnect Yukon2 support (EXPERIMENTAL)"
+ depends on PCI && EXPERIMENTAL
+ select CRC32
+ ---help---
+ This driver support the Marvell Yukon 2 Gigabit Ethernet adapter.
+
+ To compile this driver as a module, choose M here: the module
+ will be called sky2. This is recommended.
+
config SK98LIN
tristate "Marvell Yukon Chipset / SysKonnect SK-98xx Support"
depends on PCI
config SPIDER_NET
tristate "Spider Gigabit Ethernet driver"
- depends on PCI && PPC_BPA
+ depends on PCI && PPC_CELL
help
This driver supports the Gigabit Ethernet chips present on the
Cell Processor-Based Blades from IBM.