config BFIN_MAC
tristate "Blackfin on-chip MAC support"
- depends on NET_ETHERNET && (BF526 || BF527 || BF536 || BF537)
+ depends on NET_ETHERNET && (BF516 || BF518 || BF526 || BF527 || BF536 || BF537)
select CRC32
select MII
select PHYLIB
old RX-reset behavior. If unsure, say N.
config R6040
- tristate "RDC R6040 Fast Ethernet Adapter support (EXPERIMENTAL)"
+ tristate "RDC R6040 Fast Ethernet Adapter support"
depends on NET_PCI && PCI
select CRC32
select MII
config FEC
bool "FEC ethernet controller (of ColdFire CPUs)"
- depends on M523x || M527x || M5272 || M528x || M520x
+ depends on M523x || M527x || M5272 || M528x || M520x || M532x || MACH_MX27
help
Say Y here if you want to use the built-in 10/100 Fast ethernet
- controller on some Motorola ColdFire processors.
+ controller on some Motorola ColdFire and Freescale i.MX processors.
config FEC2
bool "Second FEC ethernet controller (on some ColdFire CPUs)"
To compile this driver as a module, choose M here. The module
will be called igb.
-config IGB_LRO
- bool "Use software LRO"
- depends on IGB && INET
- select INET_LRO
- ---help---
- Say Y here if you want to use large receive offload.
-
- If in doubt, say N.
-
config IGB_DCA
bool "Direct Cache Access (DCA) Support"
default y
If unsure, say N.
+config FSL_PQ_MDIO
+ tristate "Freescale PQ MDIO"
+ depends on FSL_SOC
+ select PHYLIB
+ help
+ This driver supports the MDIO bus used by the gianfar and UCC drivers.
+
config GIANFAR
tristate "Gianfar Ethernet"
depends on FSL_SOC
+ select FSL_PQ_MDIO
select PHYLIB
select CRC32
help
config UCC_GETH
tristate "Freescale QE Gigabit Ethernet"
depends on QUICC_ENGINE
+ select FSL_PQ_MDIO
select PHYLIB
help
This driver supports the Gigabit Ethernet mode of the QUICC Engine,
config MV643XX_ETH
tristate "Marvell Discovery (643XX) and Orion ethernet support"
depends on MV64360 || MV64X60 || (PPC_MULTIPLATFORM && PPC32) || PLAT_ORION
+ select INET_LRO
select PHYLIB
help
This driver supports the gigabit ethernet MACs in the
To compile this driver as a module, choose M here. The module
will be called atl1e.
+config ATL1C
+ tristate "Atheros L1C Gigabit Ethernet support (EXPERIMENTAL)"
+ depends on PCI && EXPERIMENTAL
+ select CRC32
+ select MII
+ help
+ This driver supports the Atheros L1C gigabit ethernet adapter.
+
+ To compile this driver as a module, choose M here. The module
+ will be called atl1c.
+
config JME
tristate "JMicron(R) PCI-Express Gigabit Ethernet support"
depends on PCI
Enables support for Chelsio's gigabit Ethernet PCI cards. If you
are using only 10G cards say 'N' here.
+config CHELSIO_T3_DEPENDS
+ tristate
+ depends on PCI && INET
+ default y
+
config CHELSIO_T3
tristate "Chelsio Communications T3 10Gb Ethernet support"
- depends on PCI && INET
+ depends on CHELSIO_T3_DEPENDS
select FW_LOADER
- select INET_LRO
help
This driver supports Chelsio T3-based gigabit and 10Gb Ethernet
adapters.
config IXGBE
tristate "Intel(R) 10GbE PCI Express adapters support"
depends on PCI && INET
- select INET_LRO
---help---
This driver supports Intel(R) 10GbE PCI Express family of
adapters. For more information on how to identify your adapter, go
source "drivers/net/wireless/Kconfig"
+source "drivers/net/wimax/Kconfig"
+
source "drivers/net/usb/Kconfig"
source "drivers/net/pcmcia/Kconfig"