To compile this driver as a module, choose M here: the module
will be called macvlan.
+config MACVTAP
+ tristate "MAC-VLAN based tap driver (EXPERIMENTAL)"
+ depends on MACVLAN
+ help
+ This adds a specialized tap character device driver that is based
+ on the MAC-VLAN network interface, called macvtap. A macvtap device
+ can be added in the same way as a macvlan device, using 'type
+ macvlan', and then be accessed through the tap user space interface.
+
+ To compile this driver as a module, choose M here: the module
+ will be called macvtap.
+
config EQUALIZER
tristate "EQL (serial line load balancing) support"
---help---
This is the driver for the onboard card of the Xtensa XT2000 board.
config MIPS_AU1X00_ENET
- bool "MIPS AU1000 Ethernet support"
+ tristate "MIPS AU1000 Ethernet support"
depends on SOC_AU1X00
select PHYLIB
select CRC32
Set the number of buffer packets used in driver.
config BFIN_MAC_RMII
- bool "RMII PHY Interface (EXPERIMENTAL)"
- depends on BFIN_MAC && EXPERIMENTAL
+ bool "RMII PHY Interface"
+ depends on BFIN_MAC
default y if BFIN527_EZKIT
default n if BFIN537_STAMP
help
Use Reduced PHY MII Interface
+config BFIN_MAC_USE_HWSTAMP
+ bool "Use IEEE 1588 hwstamp"
+ depends on BFIN_MAC && BF518
+ default y
+ help
+ To support the IEEE 1588 Precision Time Protocol (PTP), select y here
+
config SMC9194
tristate "SMC 9194 support"
depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN)
select CRC32
select MII
depends on ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || \
- MIPS || BLACKFIN || MN10300
+ MIPS || BLACKFIN || MN10300 || COLDFIRE
help
This is a driver for SMC's 91x series of Ethernet chipsets,
including the SMC91C94 and the SMC91C111. Say Y if you want it
config TI_DAVINCI_EMAC
tristate "TI DaVinci EMAC Support"
- depends on ARM && ARCH_DAVINCI
+ depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 )
select PHYLIB
help
This driver supports TI's DaVinci Ethernet .
config ETHOC
tristate "OpenCores 10/100 Mbps Ethernet MAC support"
- depends on NET_ETHERNET && HAS_IOMEM
+ depends on NET_ETHERNET && HAS_IOMEM && HAS_DMA
select MII
select PHYLIB
select CRC32
help
Say Y here if you want to use the OpenCores 10/100 Mbps Ethernet MAC.
+config GRETH
+ tristate "Aeroflex Gaisler GRETH Ethernet MAC support"
+ depends on SPARC
+ select PHYLIB
+ select CRC32
+ help
+ Say Y here if you want to use the Aeroflex Gaisler GRETH Ethernet MAC.
+
config SMC911X
tristate "SMSC LAN911[5678] support"
select CRC32
config SMSC911X
tristate "SMSC LAN911x/LAN921x families embedded ethernet support"
- depends on ARM || SUPERH || BLACKFIN
+ depends on ARM || SUPERH || BLACKFIN || MIPS
select CRC32
select MII
select PHYLIB
To compile this driver as a module, choose M here. The module
will be called ac3200.
+config KSZ884X_PCI
+ tristate "Micrel KSZ8841/2 PCI"
+ depends on NET_PCI && PCI
+ select MII
+ select CRC32
+ help
+ This PCI driver is for Micrel KSZ8841/KSZ8842 PCI Ethernet chip.
+
+ To compile this driver as a module, choose M here. The module
+ will be called ksz884x.
+
config APRICOT
tristate "Apricot Xen-II on board Ethernet"
depends on NET_PCI && ISA
To compile this driver as a module, choose M here. The module
will be called forcedeth.
-config FORCEDETH_NAPI
- bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
- depends on FORCEDETH && EXPERIMENTAL
- help
- NAPI is a new driver API designed to reduce CPU and interrupt load
- when the driver is receiving lots of packets from the card. It is
- still somewhat experimental and thus not yet enabled by default.
-
- If your estimated Rx load is 10kpps or more, or if the card will be
- deployed on potentially unfriendly networks (e.g. in a firewall),
- then say Y here.
-
- If in doubt, say N.
-
config CS89x0
tristate "CS89x0 support"
depends on NET_ETHERNET && (ISA || EISA || MACH_IXDP2351 \
help
SPI driver for Micrel KS8851 SPI attached network chip.
+config KS8851_MLL
+ tristate "Micrel KS8851 MLL"
+ depends on HAS_IOMEM
+ select MII
+ help
+ This platform driver is for Micrel KS8851 Address/data bus
+ multiplexed network chip.
+
config VIA_RHINE
tristate "VIA Rhine support"
depends on NET_PCI && PCI
config FEC
bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
- depends on M523x || M527x || M5272 || M528x || M520x || M532x || MACH_MX27 || ARCH_MX35
+ depends on M523x || M527x || M5272 || M528x || M520x || M532x || \
+ MACH_MX27 || ARCH_MX35 || ARCH_MX25 || ARCH_MX5
+ select PHYLIB
help
Say Y here if you want to use the built-in 10/100 Fast ethernet
controller on some Motorola ColdFire and Freescale i.MX processors.
config XILINX_EMACLITE
tristate "Xilinx 10/100 Ethernet Lite support"
depends on PPC32 || MICROBLAZE
+ select PHYLIB
help
This driver supports the 10/100 Ethernet Lite from Xilinx.
source "drivers/net/fs_enet/Kconfig"
+source "drivers/net/octeon/Kconfig"
+
endif # NET_ETHERNET
#
config GELIC_WIRELESS
bool "PS3 Wireless support"
+ depends on WLAN
depends on GELIC_NET
select WIRELESS_EXT
help
the driver automatically distinguishes the models, you can
safely enable this option even if you have a wireless-less model.
-config GELIC_WIRELESS_OLD_PSK_INTERFACE
- bool "PS3 Wireless private PSK interface (OBSOLETE)"
- depends on GELIC_WIRELESS
- help
- This option retains the obsolete private interface to pass
- the PSK from user space programs to the driver. The PSK
- stands for 'Pre Shared Key' and is used for WPA[2]-PSK
- (WPA-Personal) environment.
- If WPA[2]-PSK is used and you need to use old programs that
- support only this old interface, say Y. Otherwise N.
-
- If unsure, say N.
-
config FSL_PQ_MDIO
tristate "Freescale PQ MDIO"
depends on FSL_SOC
config XILINX_LL_TEMAC
tristate "Xilinx LL TEMAC (LocalLink Tri-mode Ethernet MAC) driver"
+ depends on PPC || MICROBLAZE
select PHYLIB
- depends on PPC_DCR_NATIVE
help
This driver supports the Xilinx 10/100/1000 LocalLink TEMAC
core used in Xilinx Spartan and Virtex FPGAs
To compile this driver as a module, choose M here. The module
will be called s6gmac.
+source "drivers/net/stmmac/Kconfig"
+
endif # NETDEV_1000
#
To compile this driver as a module, choose M here: the module
will be called cxgb3.
+config CHELSIO_T4_DEPENDS
+ tristate
+ depends on PCI && INET
+ default y
+
+config CHELSIO_T4
+ tristate "Chelsio Communications T4 Ethernet support"
+ depends on CHELSIO_T4_DEPENDS
+ select FW_LOADER
+ select MDIO
+ help
+ This driver supports Chelsio T4-based gigabit and 10Gb Ethernet
+ adapters.
+
+ For general information about Chelsio and our products, visit
+ our website at <http://www.chelsio.com>.
+
+ For customer support, please visit our customer support page at
+ <http://www.chelsio.com/support.htm>.
+
+ Please send feedback to <linux-bugs@chelsio.com>.
+
+ To compile this driver as a module choose M here; the module
+ will be called cxgb4.
+
config EHEA
tristate "eHEA Ethernet support"
depends on IBMEBUS && INET && SPARSEMEM
will be called ehea.
config ENIC
- tristate "Cisco 10G Ethernet NIC support"
+ tristate "Cisco VIC Ethernet NIC Support"
depends on PCI && INET
select INET_LRO
help
- This enables the support for the Cisco 10G Ethernet card.
+ This enables the support for the Cisco VIC Ethernet card.
config IXGBE
tristate "Intel(R) 10GbE PCI Express adapters support"
If unsure, say N.
+config IXGBEVF
+ tristate "Intel(R) 82599 Virtual Function Ethernet support"
+ depends on PCI_MSI
+ ---help---
+ This driver supports Intel(R) 82599 virtual functions. For more
+ information on how to identify your adapter, go to the Adapter &
+ Driver ID Guide at:
+
+ <http://support.intel.com/support/network/sb/CS-008441.htm>
+
+ For general information and support, go to the Intel support
+ website at:
+
+ <http://support.intel.com>
+
+ More specific information on configuring the driver is in
+ <file:Documentation/networking/ixgbevf.txt>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called ixgbevf. MSI-X interrupt support is required
+ for this driver to work correctly.
+
config IXGB
tristate "Intel(R) PRO/10GbE support"
depends on PCI
config NIU
tristate "Sun Neptune 10Gbit Ethernet support"
depends on PCI
+ select CRC32
help
This enables support for cards based upon Sun's
Neptune chipset.
To compile this driver as a module, choose M here: the module
will be called bnx2x. This is recommended.
+config QLCNIC
+ tristate "QLOGIC QLCNIC 1/10Gb Converged Ethernet NIC Support"
+ depends on PCI
+ help
+ This driver supports QLogic QLE8240 and QLE8242 Converged Ethernet
+ devices.
+
config QLGE
tristate "QLogic QLGE 10Gb Ethernet Driver Support"
depends on PCI
source "drivers/s390/net/Kconfig"
+source "drivers/net/caif/Kconfig"
+
config XEN_NETDEV_FRONTEND
tristate "Xen network device frontend driver"
depends on XEN
config PPPOL2TP
tristate "PPP over L2TP (EXPERIMENTAL)"
- depends on EXPERIMENTAL && PPP && INET
+ depends on EXPERIMENTAL && L2TP && PPP
help
Support for PPP-over-L2TP socket family. L2TP is a protocol
used by ISPs and enterprises to tunnel PPP traffic over UDP
tunnels. L2TP is replacing PPTP for VPN uses.
- This kernel component handles only L2TP data packets: a
- userland daemon handles L2TP the control protocol (tunnel
- and session setup). One such daemon is OpenL2TP
- (http://openl2tp.sourceforge.net/).
-
config SLIP
tristate "SLIP (serial line) support"
---help---
"SCSI generic support".
config NETCONSOLE
- tristate "Network console logging support (EXPERIMENTAL)"
- depends on EXPERIMENTAL
+ tristate "Network console logging support"
---help---
If you want to log kernel messages over the network, enable this.
See <file:Documentation/networking/netconsole.txt> for details.
config NETCONSOLE_DYNAMIC
- bool "Dynamic reconfiguration of logging targets (EXPERIMENTAL)"
- depends on NETCONSOLE && SYSFS && EXPERIMENTAL
+ bool "Dynamic reconfiguration of logging targets"
+ depends on NETCONSOLE && SYSFS
select CONFIGFS_FS
help
This option enables the ability to dynamically reconfigure target
This is the virtual network driver for virtio. It can be used with
lguest or QEMU based VMMs (like KVM or Xen). Say Y or M.
+config VMXNET3
+ tristate "VMware VMXNET3 ethernet driver"
+ depends on PCI && INET
+ help
+ This driver supports VMware's vmxnet3 virtual ethernet NIC.
+ To compile this driver as a module, choose M here: the
+ module will be called vmxnet3.
+
endif # NETDEVICES