-
#
# Network device configuration
#
# that for each of the symbols.
if NETDEVICES
-config COMPAT_NET_DEV_OPS
- default y
- bool "Enable older network device API compatibility"
- ---help---
- This option enables kernel compatibility with older network devices
- that do not use net_device_ops interface.
-
- If unsure, say Y.
-
config IFB
tristate "Intermediate Functional Block support"
depends on NET_CLS_ACT
To compile this driver as a module, choose M here: the module
will be called macvlan.
+config MACVTAP
+ tristate "MAC-VLAN based tap driver (EXPERIMENTAL)"
+ depends on MACVLAN
+ help
+ This adds a specialized tap character device driver that is based
+ on the MAC-VLAN network interface, called macvtap. A macvtap device
+ can be added in the same way as a macvlan device, using 'type
+ macvlan', and then be accessed through the tap user space interface.
+
+ To compile this driver as a module, choose M here: the module
+ will be called macvtap.
+
config EQUALIZER
tristate "EQL (serial line load balancing) support"
---help---
config MACB
tristate "Atmel MACB support"
- depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91CAP9
+ depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91SAM9G45 || ARCH_AT91CAP9
select PHYLIB
help
The Atmel MACB ethernet interface is found on many AT32 and AT91
This is the driver for the onboard card of the Xtensa XT2000 board.
config MIPS_AU1X00_ENET
- bool "MIPS AU1000 Ethernet support"
+ tristate "MIPS AU1000 Ethernet support"
depends on SOC_AU1X00
select PHYLIB
select CRC32
config SH_ETH
tristate "Renesas SuperH Ethernet support"
depends on SUPERH && \
- (CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712 || CPU_SUBTYPE_SH7763 || \
- CPU_SUBTYPE_SH7619)
+ (CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712 || \
+ CPU_SUBTYPE_SH7763 || CPU_SUBTYPE_SH7619 || \
+ CPU_SUBTYPE_SH7724)
select CRC32
select MII
select MDIO_BITBANG
select PHYLIB
help
Renesas SuperH Ethernet device driver.
- This driver support SH7710, SH7712, SH7763 and SH7619.
+ This driver support SH7710, SH7712, SH7763, SH7619, and SH7724.
config SUNLANCE
tristate "Sun LANCE support"
Set the number of buffer packets used in driver.
config BFIN_MAC_RMII
- bool "RMII PHY Interface (EXPERIMENTAL)"
- depends on BFIN_MAC && EXPERIMENTAL
+ bool "RMII PHY Interface"
+ depends on BFIN_MAC
default y if BFIN527_EZKIT
default n if BFIN537_STAMP
help
Use Reduced PHY MII Interface
+config BFIN_MAC_USE_HWSTAMP
+ bool "Use IEEE 1588 hwstamp"
+ depends on BFIN_MAC && BF518
+ default y
+ help
+ To support the IEEE 1588 Precision Time Protocol (PTP), select y here
+
config SMC9194
tristate "SMC 9194 support"
depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN)
select CRC32
select MII
depends on ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || \
- MIPS || BLACKFIN || MN10300
+ MIPS || BLACKFIN || MN10300 || COLDFIRE
help
This is a driver for SMC's 91x series of Ethernet chipsets,
including the SMC91C94 and the SMC91C111. Say Y if you want it
To compile this driver as a module, choose M here. The module
will be called netx-eth.
+config TI_DAVINCI_EMAC
+ tristate "TI DaVinci EMAC Support"
+ depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 )
+ select PHYLIB
+ help
+ This driver supports TI's DaVinci Ethernet .
+
+ To compile this driver as a module, choose M here: the module
+ will be called davinci_emac_driver. This is recommended.
+
config DM9000
tristate "DM9000 support"
depends on ARM || BLACKFIN || MIPS
config ETHOC
tristate "OpenCores 10/100 Mbps Ethernet MAC support"
- depends on NET_ETHERNET && HAS_IOMEM
+ depends on NET_ETHERNET && HAS_IOMEM && HAS_DMA
select MII
select PHYLIB
select CRC32
help
Say Y here if you want to use the OpenCores 10/100 Mbps Ethernet MAC.
+config GRETH
+ tristate "Aeroflex Gaisler GRETH Ethernet MAC support"
+ depends on SPARC
+ select PHYLIB
+ select CRC32
+ help
+ Say Y here if you want to use the Aeroflex Gaisler GRETH Ethernet MAC.
+
config SMC911X
tristate "SMSC LAN911[5678] support"
select CRC32
config SMSC911X
tristate "SMSC LAN911x/LAN921x families embedded ethernet support"
- depends on ARM || SUPERH
+ depends on ARM || SUPERH || BLACKFIN || MIPS
select CRC32
select MII
select PHYLIB
To compile this driver as a module, choose M here. The module
will be called ac3200.
+config KSZ884X_PCI
+ tristate "Micrel KSZ8841/2 PCI"
+ depends on NET_PCI && PCI
+ select MII
+ select CRC32
+ help
+ This PCI driver is for Micrel KSZ8841/KSZ8842 PCI Ethernet chip.
+
+ To compile this driver as a module, choose M here. The module
+ will be called ksz884x.
+
config APRICOT
tristate "Apricot Xen-II on board Ethernet"
depends on NET_PCI && ISA
To compile this driver as a module, choose M here. The module
will be called forcedeth.
-config FORCEDETH_NAPI
- bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
- depends on FORCEDETH && EXPERIMENTAL
- help
- NAPI is a new driver API designed to reduce CPU and interrupt load
- when the driver is receiving lots of packets from the card. It is
- still somewhat experimental and thus not yet enabled by default.
-
- If your estimated Rx load is 10kpps or more, or if the card will be
- deployed on potentially unfriendly networks (e.g. in a firewall),
- then say Y here.
-
- If in doubt, say N.
-
config CS89x0
tristate "CS89x0 support"
depends on NET_ETHERNET && (ISA || EISA || MACH_IXDP2351 \
Please email feedback to <torben.mathiasen@compaq.com>.
+config KS8842
+ tristate "Micrel KSZ8842"
+ depends on HAS_IOMEM
+ help
+ This platform driver is for Micrel KSZ8842 / KS8842
+ 2-port ethernet switch chip (managed, VLAN, QoS).
+
+config KS8851
+ tristate "Micrel KS8851 SPI"
+ depends on SPI
+ select MII
+ select CRC32
+ help
+ SPI driver for Micrel KS8851 SPI attached network chip.
+
+config KS8851_MLL
+ tristate "Micrel KS8851 MLL"
+ depends on HAS_IOMEM
+ select MII
+ help
+ This platform driver is for Micrel KS8851 Address/data bus
+ multiplexed network chip.
+
config VIA_RHINE
tristate "VIA Rhine support"
depends on NET_PCI && PCI
config CPMAC
tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)"
- depends on NET_ETHERNET && EXPERIMENTAL && AR7 && BROKEN
+ depends on NET_ETHERNET && EXPERIMENTAL && AR7
select PHYLIB
help
TI AR7 CPMAC Ethernet support
the Motorola 68360 processor.
config FEC
- bool "FEC ethernet controller (of ColdFire CPUs)"
- depends on M523x || M527x || M5272 || M528x || M520x || M532x || MACH_MX27
+ bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
+ depends on M523x || M527x || M5272 || M528x || M520x || M532x || \
+ MACH_MX27 || ARCH_MX35 || ARCH_MX25 || ARCH_MX5
+ select PHYLIB
help
Say Y here if you want to use the built-in 10/100 Fast ethernet
controller on some Motorola ColdFire and Freescale i.MX processors.
---help---
This option enables support for the MPC5200's on-chip
Fast Ethernet Controller
- If compiled as module, it will be called 'fec_mpc52xx.ko'.
+ If compiled as module, it will be called fec_mpc52xx.
config FEC_MPC52xx_MDIO
bool "MPC52xx FEC MDIO bus driver"
(Motorola? industry standard).
If your board uses an external PHY connected to FEC, enable this.
If not sure, enable.
- If compiled as module, it will be called 'fec_mpc52xx_phy.ko'.
+ If compiled as module, it will be called fec_mpc52xx_phy.
config NE_H8300
tristate "NE2000 compatible support for H8/300"
To compile this driver as a module, choose M here. The module
will be called atl2.
+config XILINX_EMACLITE
+ tristate "Xilinx 10/100 Ethernet Lite support"
+ depends on PPC32 || MICROBLAZE
+ select PHYLIB
+ help
+ This driver supports the 10/100 Ethernet Lite from Xilinx.
+
+config BCM63XX_ENET
+ tristate "Broadcom 63xx internal mac support"
+ depends on BCM63XX
+ select MII
+ select PHYLIB
+ help
+ This driver supports the ethernet MACs in the Broadcom 63xx
+ MIPS chipset family (BCM63XX).
+
source "drivers/net/fs_enet/Kconfig"
+source "drivers/net/octeon/Kconfig"
+
endif # NET_ETHERNET
#
depends on SKGE && DEBUG_FS
help
This option adds the ability to dump driver state for debugging.
- The file debugfs/skge/ethX displays the state of the internal
+ The file /sys/kernel/debug/skge/ethX displays the state of the internal
transmit and receive rings.
If unsure, say N.
depends on SKY2 && DEBUG_FS
help
This option adds the ability to dump driver state for debugging.
- The file debugfs/sky2/ethX displays the state of the internal
+ The file /sys/kernel/debug/sky2/ethX displays the state of the internal
transmit and receive rings.
If unsure, say N.
To compile this driver as a module, choose M here: the module
will be called bnx2. This is recommended.
+config CNIC
+ tristate "Broadcom CNIC support"
+ depends on PCI
+ select BNX2
+ select UIO
+ help
+ This driver supports offload features of Broadcom NetXtremeII
+ gigabit Ethernet cards.
+
+ To compile this driver as a module, choose M here: the module
+ will be called cnic. This is recommended.
+
config SPIDER_NET
tristate "Spider Gigabit Ethernet driver"
depends on PCI && (PPC_IBM_CELL_BLADE || PPC_CELLEB)
config GELIC_WIRELESS
bool "PS3 Wireless support"
+ depends on WLAN
depends on GELIC_NET
select WIRELESS_EXT
help
the driver automatically distinguishes the models, you can
safely enable this option even if you have a wireless-less model.
-config GELIC_WIRELESS_OLD_PSK_INTERFACE
- bool "PS3 Wireless private PSK interface (OBSOLETE)"
- depends on GELIC_WIRELESS
- help
- This option retains the obsolete private interface to pass
- the PSK from user space programs to the driver. The PSK
- stands for 'Pre Shared Key' and is used for WPA[2]-PSK
- (WPA-Personal) environment.
- If WPA[2]-PSK is used and you need to use old programs that
- support only this old interface, say Y. Otherwise N.
-
- If unsure, say N.
-
config FSL_PQ_MDIO
tristate "Freescale PQ MDIO"
depends on FSL_SOC
This driver supports the Gigabit Ethernet mode of the QUICC Engine,
which is available on some Freescale SOCs.
-config UGETH_MAGIC_PACKET
- bool "Magic Packet detection support"
- depends on UCC_GETH
-
config UGETH_TX_ON_DEMAND
bool "Transmit on Demand support"
depends on UCC_GETH
config MV643XX_ETH
tristate "Marvell Discovery (643XX) and Orion ethernet support"
- depends on MV64360 || MV64X60 || (PPC_MULTIPLATFORM && PPC32) || PLAT_ORION
+ depends on MV64X60 || PPC32 || PLAT_ORION
select INET_LRO
select PHYLIB
help
config XILINX_LL_TEMAC
tristate "Xilinx LL TEMAC (LocalLink Tri-mode Ethernet MAC) driver"
+ depends on PPC || MICROBLAZE
select PHYLIB
- depends on PPC_DCR_NATIVE
help
This driver supports the Xilinx 10/100/1000 LocalLink TEMAC
core used in Xilinx Spartan and Virtex FPGAs
To compile this driver as a module, choose M here. The module
will be called jme.
+config S6GMAC
+ tristate "S6105 GMAC ethernet support"
+ depends on XTENSA_VARIANT_S6000
+ select PHYLIB
+ help
+ This driver supports the on chip ethernet device on the
+ S6105 xtensa processor.
+
+ To compile this driver as a module, choose M here. The module
+ will be called s6gmac.
+
+source "drivers/net/stmmac/Kconfig"
+
endif # NETDEV_1000
#
tristate "Chelsio 10Gb Ethernet support"
depends on PCI
select CRC32
+ select MDIO
help
This driver supports Chelsio gigabit and 10-gigabit
Ethernet cards. More information about adapter features and
tristate "Chelsio Communications T3 10Gb Ethernet support"
depends on CHELSIO_T3_DEPENDS
select FW_LOADER
+ select MDIO
help
This driver supports Chelsio T3-based gigabit and 10Gb Ethernet
adapters.
To compile this driver as a module, choose M here: the module
will be called cxgb3.
+config CHELSIO_T4_DEPENDS
+ tristate
+ depends on PCI && INET
+ default y
+
+config CHELSIO_T4
+ tristate "Chelsio Communications T4 Ethernet support"
+ depends on CHELSIO_T4_DEPENDS
+ select FW_LOADER
+ select MDIO
+ help
+ This driver supports Chelsio T4-based gigabit and 10Gb Ethernet
+ adapters.
+
+ For general information about Chelsio and our products, visit
+ our website at <http://www.chelsio.com>.
+
+ For customer support, please visit our customer support page at
+ <http://www.chelsio.com/support.htm>.
+
+ Please send feedback to <linux-bugs@chelsio.com>.
+
+ To compile this driver as a module choose M here; the module
+ will be called cxgb4.
+
config EHEA
tristate "eHEA Ethernet support"
depends on IBMEBUS && INET && SPARSEMEM
will be called ehea.
config ENIC
- tristate "Cisco 10G Ethernet NIC support"
+ tristate "Cisco VIC Ethernet NIC Support"
depends on PCI && INET
select INET_LRO
help
- This enables the support for the Cisco 10G Ethernet card.
+ This enables the support for the Cisco VIC Ethernet card.
config IXGBE
tristate "Intel(R) 10GbE PCI Express adapters support"
depends on PCI && INET
+ select MDIO
---help---
This driver supports Intel(R) 10GbE PCI Express family of
adapters. For more information on how to identify your adapter, go
If unsure, say N.
+config IXGBEVF
+ tristate "Intel(R) 82599 Virtual Function Ethernet support"
+ depends on PCI_MSI
+ ---help---
+ This driver supports Intel(R) 82599 virtual functions. For more
+ information on how to identify your adapter, go to the Adapter &
+ Driver ID Guide at:
+
+ <http://support.intel.com/support/network/sb/CS-008441.htm>
+
+ For general information and support, go to the Intel support
+ website at:
+
+ <http://support.intel.com>
+
+ More specific information on configuring the driver is in
+ <file:Documentation/networking/ixgbevf.txt>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called ixgbevf. MSI-X interrupt support is required
+ for this driver to work correctly.
+
config IXGB
tristate "Intel(R) PRO/10GbE support"
depends on PCI
config NIU
tristate "Sun Neptune 10Gbit Ethernet support"
depends on PCI
+ select CRC32
help
This enables support for cards based upon Sun's
Neptune chipset.
select FW_LOADER
select ZLIB_INFLATE
select LIBCRC32C
+ select MDIO
help
This driver supports Broadcom NetXtremeII 10 gigabit Ethernet cards.
To compile this driver as a module, choose M here: the module
will be called bnx2x. This is recommended.
+config QLCNIC
+ tristate "QLOGIC QLCNIC 1/10Gb Converged Ethernet NIC Support"
+ depends on PCI
+ help
+ This driver supports QLogic QLE8240 and QLE8242 Converged Ethernet
+ devices.
+
config QLGE
tristate "QLogic QLGE 10Gb Ethernet Driver Support"
depends on PCI
source "drivers/atm/Kconfig"
+source "drivers/ieee802154/Kconfig"
+
source "drivers/s390/net/Kconfig"
+source "drivers/net/caif/Kconfig"
+
config XEN_NETDEV_FRONTEND
tristate "Xen network device frontend driver"
depends on XEN
config PPPOL2TP
tristate "PPP over L2TP (EXPERIMENTAL)"
- depends on EXPERIMENTAL && PPP && INET
+ depends on EXPERIMENTAL && L2TP && PPP
help
Support for PPP-over-L2TP socket family. L2TP is a protocol
used by ISPs and enterprises to tunnel PPP traffic over UDP
tunnels. L2TP is replacing PPTP for VPN uses.
- This kernel component handles only L2TP data packets: a
- userland daemon handles L2TP the control protocol (tunnel
- and session setup). One such daemon is OpenL2TP
- (http://openl2tp.sourceforge.net/).
-
config SLIP
tristate "SLIP (serial line) support"
---help---
"SCSI generic support".
config NETCONSOLE
- tristate "Network console logging support (EXPERIMENTAL)"
- depends on EXPERIMENTAL
+ tristate "Network console logging support"
---help---
If you want to log kernel messages over the network, enable this.
See <file:Documentation/networking/netconsole.txt> for details.
config NETCONSOLE_DYNAMIC
- bool "Dynamic reconfiguration of logging targets (EXPERIMENTAL)"
- depends on NETCONSOLE && SYSFS && EXPERIMENTAL
+ bool "Dynamic reconfiguration of logging targets"
+ depends on NETCONSOLE && SYSFS
select CONFIGFS_FS
help
This option enables the ability to dynamically reconfigure target
This is the virtual network driver for virtio. It can be used with
lguest or QEMU based VMMs (like KVM or Xen). Say Y or M.
+config VMXNET3
+ tristate "VMware VMXNET3 ethernet driver"
+ depends on PCI && INET
+ help
+ This driver supports VMware's vmxnet3 virtual ethernet NIC.
+ To compile this driver as a module, choose M here: the
+ module will be called vmxnet3.
+
endif # NETDEVICES