# that for each of the symbols.
if NETDEVICES
+config COMPAT_NET_DEV_OPS
+ default y
+ bool "Enable older network device API compatibility"
+ ---help---
+ This option enables kernel compatibility with older network devices
+ that do not use net_device_ops interface.
+
+ If unsure, say Y.
+
config IFB
tristate "Intermediate Functional Block support"
depends on NET_CLS_ACT
Enable the verify after the buffer write useful for debugging purpose.
If unsure, say N.
+config ETHOC
+ tristate "OpenCores 10/100 Mbps Ethernet MAC support"
+ depends on NET_ETHERNET && HAS_IOMEM
+ select MII
+ select PHYLIB
+ select CRC32
+ select BITREVERSE
+ help
+ Say Y here if you want to use the OpenCores 10/100 Mbps Ethernet MAC.
+
config SMC911X
tristate "SMSC LAN911[5678] support"
select CRC32
To compile this driver as a module, choose M here. The module
will be called ni65.
+config DNET
+ tristate "Dave ethernet support (DNET)"
+ depends on NET_ETHERNET && HAS_IOMEM
+ select PHYLIB
+ help
+ The Dave ethernet interface (DNET) is found on Qong Board FPGA.
+ Say Y to include support for the DNET chip.
+
+ To compile this driver as a module, choose M here: the module
+ will be called dnet.
+
source "drivers/net/tulip/Kconfig"
config AT1700
config FEC
bool "FEC ethernet controller (of ColdFire CPUs)"
- depends on M523x || M527x || M5272 || M528x || M520x
+ depends on M523x || M527x || M5272 || M528x || M520x || M532x || MACH_MX27
help
Say Y here if you want to use the built-in 10/100 Fast ethernet
- controller on some Motorola ColdFire processors.
+ controller on some Motorola ColdFire and Freescale i.MX processors.
config FEC2
bool "Second FEC ethernet controller (on some ColdFire CPUs)"
To compile this driver as a module, choose M here. The module
will be called igb.
-config IGB_LRO
- bool "Use software LRO"
- depends on IGB && INET
- ---help---
- Say Y here if you want to use large receive offload.
-
- If in doubt, say N.
-
config IGB_DCA
bool "Direct Cache Access (DCA) Support"
default y
driver. DCA is a method for warming the CPU cache before data
is used, with the intent of lessening the impact of cache misses.
+config IGBVF
+ tristate "Intel(R) 82576 Virtual Function Ethernet support"
+ depends on PCI
+ ---help---
+ This driver supports Intel(R) 82576 virtual functions. For more
+ information on how to identify your adapter, go to the Adapter &
+ Driver ID Guide at:
+
+ <http://support.intel.com/support/network/adapter/pro100/21397.htm>
+
+ For general information and support, go to the Intel support
+ website at:
+
+ <http://support.intel.com>
+
+ More specific information on configuring the driver is in
+ <file:Documentation/networking/e1000.txt>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called igbvf.
+
source "drivers/net/ixp2000/Kconfig"
config MYRI_SBUS
tristate "Broadcom NetXtremeII support"
depends on PCI
select CRC32
- select ZLIB_INFLATE
+ select FW_LOADER
help
This driver supports Broadcom NetXtremeII gigabit Ethernet cards.
If unsure, say N.
+config FSL_PQ_MDIO
+ tristate "Freescale PQ MDIO"
+ depends on FSL_SOC
+ select PHYLIB
+ help
+ This driver supports the MDIO bus used by the gianfar and UCC drivers.
+
config GIANFAR
tristate "Gianfar Ethernet"
depends on FSL_SOC
+ select FSL_PQ_MDIO
select PHYLIB
select CRC32
help
config UCC_GETH
tristate "Freescale QE Gigabit Ethernet"
depends on QUICC_ENGINE
+ select FSL_PQ_MDIO
select PHYLIB
help
This driver supports the Gigabit Ethernet mode of the QUICC Engine,
config MV643XX_ETH
tristate "Marvell Discovery (643XX) and Orion ethernet support"
depends on MV64360 || MV64X60 || (PPC_MULTIPLATFORM && PPC32) || PLAT_ORION
+ select INET_LRO
select PHYLIB
help
This driver supports the gigabit ethernet MACs in the
To compile this driver as a module, choose M here. The module
will be called atl1e.
+config ATL1C
+ tristate "Atheros L1C Gigabit Ethernet support (EXPERIMENTAL)"
+ depends on PCI && EXPERIMENTAL
+ select CRC32
+ select MII
+ help
+ This driver supports the Atheros L1C gigabit ethernet adapter.
+
+ To compile this driver as a module, choose M here. The module
+ will be called atl1c.
+
config JME
tristate "JMicron(R) PCI-Express Gigabit Ethernet support"
depends on PCI
More specific information on configuring the driver is in
<file:Documentation/networking/s2io.txt>.
+config VXGE
+ tristate "Neterion X3100 Series 10GbE PCIe Server Adapter"
+ depends on PCI && INET
+ ---help---
+ This driver supports Neterion Inc's X3100 Series 10 GbE PCIe
+ I/O Virtualized Server Adapter.
+ More specific information on configuring the driver is in
+ <file:Documentation/networking/vxge.txt>.
+
+config VXGE_DEBUG_TRACE_ALL
+ bool "Enabling All Debug trace statments in driver"
+ default n
+ depends on VXGE
+ ---help---
+ Say Y here if you want to enabling all the debug trace statements in
+ driver. By default only few debug trace statements are enabled.
+
config MYRI10GE
tristate "Myricom Myri-10G Ethernet support"
depends on PCI && INET
source "drivers/net/sfc/Kconfig"
+source "drivers/net/benet/Kconfig"
+
endif # NETDEV_10000
source "drivers/net/tokenring/Kconfig"
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff