# that for each of the symbols.
if NETDEVICES
+config COMPAT_NET_DEV_OPS
+ default y
+ bool "Enable older network device API compatibility"
+ ---help---
+ This option enables kernel compatibility with older network devices
+ that do not use net_device_ops interface.
+
+ If unsure, say Y.
+
config IFB
tristate "Intermediate Functional Block support"
depends on NET_CLS_ACT
config BONDING
tristate "Bonding driver support"
depends on INET
+ depends on IPV6 || IPV6=n
---help---
Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
Channels together. This is called 'Etherchannel' by Cisco,
This is the driver for the onboard card of MIPS Magnum 4000,
Acer PICA, Olivetti M700-10 and a few other identical OEM systems.
+config XTENSA_XT2000_SONIC
+ tristate "Xtensa XT2000 onboard SONIC Ethernet support"
+ depends on XTENSA_PLATFORM_XT2000
+ help
+ This is the driver for the onboard card of the Xtensa XT2000 board.
+
config MIPS_AU1X00_ENET
bool "MIPS AU1000 Ethernet support"
depends on SOC_AU1X00
config BFIN_MAC
tristate "Blackfin on-chip MAC support"
- depends on NET_ETHERNET && (BF526 || BF527 || BF536 || BF537)
+ depends on NET_ETHERNET && (BF516 || BF518 || BF526 || BF527 || BF536 || BF537)
select CRC32
select MII
select PHYLIB
select CRC32
select MII
depends on ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || \
- SOC_AU1X00 || BLACKFIN || MN10300
+ MIPS || BLACKFIN || MN10300
help
This is a driver for SMC's 91x series of Ethernet chipsets,
including the SMC91C94 and the SMC91C111. Say Y if you want it
Enable the verify after the buffer write useful for debugging purpose.
If unsure, say N.
+config ETHOC
+ tristate "OpenCores 10/100 Mbps Ethernet MAC support"
+ depends on NET_ETHERNET && HAS_IOMEM
+ select MII
+ select PHYLIB
+ select CRC32
+ select BITREVERSE
+ help
+ Say Y here if you want to use the OpenCores 10/100 Mbps Ethernet MAC.
+
config SMC911X
tristate "SMSC LAN911[5678] support"
select CRC32
select MII
- depends on ARCH_PXA || SUPERH
+ depends on ARM || SUPERH
help
This is a driver for SMSC's LAN911x series of Ethernet chipsets
including the new LAN9115, LAN9116, LAN9117, and LAN9118.
called smc911x. If you want to compile it as a module, say M
here and read <file:Documentation/kbuild/modules.txt>
+config SMSC911X
+ tristate "SMSC LAN911x/LAN921x families embedded ethernet support"
+ depends on ARM || SUPERH
+ select CRC32
+ select MII
+ select PHYLIB
+ ---help---
+ Say Y here if you want support for SMSC LAN911x and LAN921x families
+ of ethernet controllers.
+
+ To compile this driver as a module, choose M here and read
+ <file:Documentation/networking/net-modules.txt>. The module
+ will be called smsc911x.
+
config NET_VENDOR_RACAL
bool "Racal-Interlan (Micom) NI cards"
depends on ISA
To compile this driver as a module, choose M here. The module
will be called ni65.
+config DNET
+ tristate "Dave ethernet support (DNET)"
+ depends on NET_ETHERNET && HAS_IOMEM
+ select PHYLIB
+ help
+ The Dave ethernet interface (DNET) is found on Qong Board FPGA.
+ Say Y to include support for the DNET chip.
+
+ To compile this driver as a module, choose M here: the module
+ will be called dnet.
+
source "drivers/net/tulip/Kconfig"
config AT1700
config CS89x0
tristate "CS89x0 support"
- depends on NET_PCI && (ISA || MACH_IXDP2351 || ARCH_IXDP2X01 || ARCH_PNX010X)
+ depends on NET_ETHERNET && (ISA || EISA || MACH_IXDP2351 \
+ || ARCH_IXDP2X01 || ARCH_PNX010X || MACH_MX31ADS)
---help---
Support for CS89x0 chipset based Ethernet cards. If you have a
network (Ethernet) card of this type, say Y and read the
To compile this driver as a module, choose M here. The module
will be called cs89x0.
+config CS89x0_NONISA_IRQ
+ def_bool y
+ depends on CS89x0 != n
+ depends on MACH_IXDP2351 || ARCH_IXDP2X01 || ARCH_PNX010X || MACH_MX31ADS
+
config TC35815
tristate "TOSHIBA TC35815 Ethernet support"
depends on NET_PCI && PCI && MIPS
select PHYLIB
-config EEPRO100
- tristate "EtherExpressPro/100 support (eepro100, original Becker driver)"
- depends on NET_PCI && PCI
- select MII
- help
- If you have an Intel EtherExpress PRO/100 PCI network (Ethernet)
- card, say Y and read the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called eepro100.
-
-
config E100
tristate "Intel(R) PRO/100+ support"
depends on NET_PCI && PCI
old RX-reset behavior. If unsure, say N.
config R6040
- tristate "RDC R6040 Fast Ethernet Adapter support (EXPERIMENTAL)"
+ tristate "RDC R6040 Fast Ethernet Adapter support"
depends on NET_PCI && PCI
select CRC32
select MII
More specific information and updates are available from
<http://www.scyld.com/network/epic100.html>.
+config SMSC9420
+ tristate "SMSC LAN9420 PCI ethernet adapter support"
+ depends on NET_PCI && PCI
+ select CRC32
+ select PHYLIB
+ select SMSC_PHY
+ help
+ This is a driver for SMSC's LAN9420 PCI ethernet adapter.
+ Say Y if you want it compiled into the kernel,
+ and read the Ethernet-HOWTO, available from
+ <http://www.linuxdoc.org/docs.html#howto>.
+
+ This driver is also available as a module. The module will be
+ called smsc9420. If you want to compile it as a module, say M
+ here and read <file:Documentation/kbuild/modules.txt>
+
config SUNDANCE
tristate "Sundance Alta support"
depends on NET_PCI && PCI
config FEC
bool "FEC ethernet controller (of ColdFire CPUs)"
- depends on M523x || M527x || M5272 || M528x || M520x
+ depends on M523x || M527x || M5272 || M528x || M520x || M532x || MACH_MX27
help
Say Y here if you want to use the built-in 10/100 Fast ethernet
- controller on some Motorola ColdFire processors.
+ controller on some Motorola ColdFire and Freescale i.MX processors.
config FEC2
bool "Second FEC ethernet controller (on some ColdFire CPUs)"
config FEC_MPC52xx
tristate "MPC52xx FEC driver"
- depends on PPC_MPC52xx && PPC_BESTCOMM_FEC
+ depends on PPC_MPC52xx && PPC_BESTCOMM
select CRC32
select PHYLIB
+ select PPC_BESTCOMM_FEC
---help---
This option enables support for the MPC5200's on-chip
Fast Ethernet Controller
will be called ipg. This is recommended.
config IGB
- tristate "Intel(R) 82575 PCI-Express Gigabit Ethernet support"
+ tristate "Intel(R) 82575/82576 PCI-Express Gigabit Ethernet support"
depends on PCI
---help---
- This driver supports Intel(R) 82575 gigabit ethernet family of
+ This driver supports Intel(R) 82575/82576 gigabit ethernet family of
adapters. For more information on how to identify your adapter, go
to the Adapter & Driver ID Guide at:
To compile this driver as a module, choose M here. The module
will be called igb.
-config IGB_LRO
- bool "Use software LRO"
- depends on IGB && INET
- select INET_LRO
+config IGB_DCA
+ bool "Direct Cache Access (DCA) Support"
+ default y
+ depends on IGB && DCA && !(IGB=y && DCA=m)
---help---
- Say Y here if you want to use large receive offload.
+ Say Y here if you want to use Direct Cache Access (DCA) in the
+ driver. DCA is a method for warming the CPU cache before data
+ is used, with the intent of lessening the impact of cache misses.
- If in doubt, say N.
+config IGBVF
+ tristate "Intel(R) 82576 Virtual Function Ethernet support"
+ depends on PCI
+ ---help---
+ This driver supports Intel(R) 82576 virtual functions. For more
+ information on how to identify your adapter, go to the Adapter &
+ Driver ID Guide at:
+
+ <http://support.intel.com/support/network/adapter/pro100/21397.htm>
+
+ For general information and support, go to the Intel support
+ website at:
+
+ <http://support.intel.com>
+
+ More specific information on configuring the driver is in
+ <file:Documentation/networking/e1000.txt>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called igbvf.
source "drivers/net/ixp2000/Kconfig"
tristate "Broadcom NetXtremeII support"
depends on PCI
select CRC32
- select ZLIB_INFLATE
+ select FW_LOADER
help
This driver supports Broadcom NetXtremeII gigabit Ethernet cards.
If unsure, say N.
+config FSL_PQ_MDIO
+ tristate "Freescale PQ MDIO"
+ depends on FSL_SOC
+ select PHYLIB
+ help
+ This driver supports the MDIO bus used by the gianfar and UCC drivers.
+
config GIANFAR
tristate "Gianfar Ethernet"
depends on FSL_SOC
+ select FSL_PQ_MDIO
select PHYLIB
select CRC32
help
config UCC_GETH
tristate "Freescale QE Gigabit Ethernet"
depends on QUICC_ENGINE
+ select FSL_PQ_MDIO
select PHYLIB
help
This driver supports the Gigabit Ethernet mode of the QUICC Engine,
bool "Magic Packet detection support"
depends on UCC_GETH
-config UGETH_FILTERING
- bool "Mac address filtering support"
- depends on UCC_GETH
-
config UGETH_TX_ON_DEMAND
bool "Transmit on Demand support"
depends on UCC_GETH
config MV643XX_ETH
tristate "Marvell Discovery (643XX) and Orion ethernet support"
depends on MV64360 || MV64X60 || (PPC_MULTIPLATFORM && PPC32) || PLAT_ORION
+ select INET_LRO
select PHYLIB
help
This driver supports the gigabit ethernet MACs in the
will be called qla3xxx.
config ATL1
- tristate "Attansic L1 Gigabit Ethernet support (EXPERIMENTAL)"
- depends on PCI && EXPERIMENTAL
+ tristate "Atheros/Attansic L1 Gigabit Ethernet support"
+ depends on PCI
select CRC32
select MII
help
- This driver supports the Attansic L1 gigabit ethernet adapter.
+ This driver supports the Atheros/Attansic L1 gigabit ethernet
+ adapter.
To compile this driver as a module, choose M here. The module
will be called atl1.
To compile this driver as a module, choose M here. The module
will be called atl1e.
+config ATL1C
+ tristate "Atheros L1C Gigabit Ethernet support (EXPERIMENTAL)"
+ depends on PCI && EXPERIMENTAL
+ select CRC32
+ select MII
+ help
+ This driver supports the Atheros L1C gigabit ethernet adapter.
+
+ To compile this driver as a module, choose M here. The module
+ will be called atl1c.
+
config JME
tristate "JMicron(R) PCI-Express Gigabit Ethernet support"
depends on PCI
Enables support for Chelsio's gigabit Ethernet PCI cards. If you
are using only 10G cards say 'N' here.
+config CHELSIO_T3_DEPENDS
+ tristate
+ depends on PCI && INET
+ default y
+
config CHELSIO_T3
tristate "Chelsio Communications T3 10Gb Ethernet support"
- depends on PCI && INET
+ depends on CHELSIO_T3_DEPENDS
select FW_LOADER
- select INET_LRO
help
This driver supports Chelsio T3-based gigabit and 10Gb Ethernet
adapters.
will be called ehea.
config ENIC
- tristate "E, the Cisco 10G Ethernet NIC"
+ tristate "Cisco 10G Ethernet NIC support"
depends on PCI && INET
select INET_LRO
help
config IXGBE
tristate "Intel(R) 10GbE PCI Express adapters support"
depends on PCI && INET
- select INET_LRO
- select INTEL_IOATDMA
---help---
This driver supports Intel(R) 10GbE PCI Express family of
adapters. For more information on how to identify your adapter, go
To compile this driver as a module, choose M here. The module
will be called ixgbe.
+config IXGBE_DCA
+ bool "Direct Cache Access (DCA) Support"
+ default y
+ depends on IXGBE && DCA && !(IXGBE=y && DCA=m)
+ ---help---
+ Say Y here if you want to use Direct Cache Access (DCA) in the
+ driver. DCA is a method for warming the CPU cache before data
+ is used, with the intent of lessening the impact of cache misses.
+
+config IXGBE_DCB
+ bool "Data Center Bridging (DCB) Support"
+ default n
+ depends on IXGBE && DCB
+ ---help---
+ Say Y here if you want to use Data Center Bridging (DCB) in the
+ driver.
+
+ If unsure, say N.
+
config IXGB
tristate "Intel(R) PRO/10GbE support"
depends on PCI
More specific information on configuring the driver is in
<file:Documentation/networking/s2io.txt>.
+config VXGE
+ tristate "Neterion X3100 Series 10GbE PCIe Server Adapter"
+ depends on PCI && INET
+ ---help---
+ This driver supports Neterion Inc's X3100 Series 10 GbE PCIe
+ I/O Virtualized Server Adapter.
+ More specific information on configuring the driver is in
+ <file:Documentation/networking/vxge.txt>.
+
+config VXGE_DEBUG_TRACE_ALL
+ bool "Enabling All Debug trace statments in driver"
+ default n
+ depends on VXGE
+ ---help---
+ Say Y here if you want to enabling all the debug trace statements in
+ driver. By default only few debug trace statements are enabled.
+
config MYRI10GE
tristate "Myricom Myri-10G Ethernet support"
depends on PCI && INET
select FW_LOADER
select CRC32
select INET_LRO
- select INTEL_IOATDMA
---help---
This driver supports Myricom Myri-10G Dual Protocol interface in
Ethernet mode. If the eeprom on your board is not recent enough,
To compile this driver as a module, choose M here. The module
will be called myri10ge.
+config MYRI10GE_DCA
+ bool "Direct Cache Access (DCA) Support"
+ default y
+ depends on MYRI10GE && DCA && !(MYRI10GE=y && DCA=m)
+ ---help---
+ Say Y here if you want to use Direct Cache Access (DCA) in the
+ driver. DCA is a method for warming the CPU cache before data
+ is used, with the intent of lessening the impact of cache misses.
+
config NETXEN_NIC
tristate "NetXen Multi port (1/10) Gigabit Ethernet NIC"
depends on PCI
This driver supports the on-chip 1/10Gbit Ethernet controller on
PA Semi's PWRficient line of chips.
+config MLX4_EN
+ tristate "Mellanox Technologies 10Gbit Ethernet support"
+ depends on PCI && INET
+ select MLX4_CORE
+ select INET_LRO
+ help
+ This driver supports Mellanox Technologies ConnectX Ethernet
+ devices.
+
config MLX4_CORE
tristate
depends on PCI
source "drivers/net/sfc/Kconfig"
+source "drivers/net/benet/Kconfig"
+
endif # NETDEV_10000
source "drivers/net/tokenring/Kconfig"
source "drivers/net/wireless/Kconfig"
+source "drivers/net/wimax/Kconfig"
+
source "drivers/net/usb/Kconfig"
source "drivers/net/pcmcia/Kconfig"
default "128"
config FDDI
- bool "FDDI driver support"
+ tristate "FDDI driver support"
depends on (PCI || EISA || TC)
help
Fiber Distributed Data Interface is a high speed local area network
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff