tristate "Intermediate Functional Block support"
depends on NET_CLS_ACT
---help---
- This is an intermidiate driver that allows sharing of
+ This is an intermediate driver that allows sharing of
resources.
To compile this driver as a module, choose M here: the module
will be called ifb. If you want to use more than one ifb
or internal device. It is safe to say Y or M here even if your
ethernet card lack MII.
+config MACB
+ tristate "Atmel MACB support"
+ depends on NET_ETHERNET && AVR32
+ select MII
+ help
+ The Atmel MACB ethernet interface is found on many AT32 and AT91
+ parts. Say Y to include support for the MACB chip.
+
+ To compile this driver as a module, choose M here: the module
+ will be called macb.
+
source "drivers/net/arm/Kconfig"
config MACE
config MIPS_SIM_NET
tristate "MIPS simulator Network device (EXPERIMENTAL)"
- depends on NETDEVICES && MIPS_SIM && EXPERIMENTAL
+ depends on MIPS_SIM && EXPERIMENTAL
help
The MIPSNET device is a simple Ethernet network device which is
emulated by the MIPS Simulator.
information.
config LAN_SAA9730
- bool "Philips SAA9730 Ethernet support (EXPERIMENTAL)"
- depends on NET_PCI && EXPERIMENTAL && MIPS
+ bool "Philips SAA9730 Ethernet support"
+ depends on NET_PCI && PCI && MIPS_ATLAS
help
The SAA9730 is a combined multimedia and peripheral controller used
in thin clients, Internet access terminals, and diskless
workstations.
See <http://www.semiconductors.philips.com/pip/SAA9730_flyer_1>.
+config SC92031
+ tristate "Silan SC92031 PCI Fast Ethernet Adapter driver (EXPERIMENTAL)"
+ depends on NET_PCI && PCI && EXPERIMENTAL
+ select CRC32
+ ---help---
+ This is a driver for the Fast Ethernet PCI network cards based on
+ the Silan SC92031 chip (sometimes also called Rsltek 8139D). If you
+ have one of these, say Y here.
+
+ To compile this driver as a module, choose M here: the module
+ will be called sc92031. This is recommended.
+
config NET_POCKET
bool "Pocket and portable adapters"
depends on NET_ETHERNET && PARPORT
This driver supports the original Yukon chipset. A cleaner driver is
also available (skge) which seems to work better than this one.
- This driver does not support the newer Yukon2 chipset. A seperate
+ This driver does not support the newer Yukon2 chipset. A separate
driver, sky2, is provided to support Yukon2-based adapters.
The following adapters are supported by this driver:
This driver supports the Gigabit Ethernet chips present on the
Cell Processor-Based Blades from IBM.
+config TSI108_ETH
+ tristate "Tundra TSI108 gigabit Ethernet support"
+ depends on TSI108_BRIDGE
+ help
+ This driver supports Tundra TSI108 gigabit Ethernet ports.
+ To compile this driver as a module, choose M here: the module
+ will be called tsi108_eth.
+
config GIANFAR
tristate "Gianfar Ethernet"
depends on 85xx || 83xx || PPC_86xx
config CHELSIO_T1
tristate "Chelsio 10Gb Ethernet support"
depends on PCI
+ select CRC32
help
- This driver supports Chelsio N110 and N210 models 10Gb Ethernet
- cards. More information about adapter features and performance
- tuning is in <file:Documentation/networking/cxgb.txt>.
+ This driver supports Chelsio gigabit and 10-gigabit
+ Ethernet cards. More information about adapter features and
+ performance tuning is in <file:Documentation/networking/cxgb.txt>.
For general information about Chelsio and our products, visit
our website at <http://www.chelsio.com>.
To compile this driver as a module, choose M here: the module
will be called cxgb.
+config CHELSIO_T1_1G
+ bool "Chelsio gigabit Ethernet support"
+ depends on CHELSIO_T1
+ help
+ Enables support for Chelsio's gigabit Ethernet PCI cards. If you
+ are using only 10G cards say 'N' here.
+
+config CHELSIO_T1_NAPI
+ bool "Use Rx Polling (NAPI)"
+ depends on CHELSIO_T1
+ default y
+ help
+ NAPI is a driver API designed to reduce CPU and interrupt load
+ when the driver is receiving lots of packets from the card.
+
config EHEA
tristate "eHEA Ethernet support"
depends on IBMEBUS
<file:Documentation/networking/net-modules.txt>. The module
will be called myri10ge.
+config NETXEN_NIC
+ tristate "NetXen Multi port (1/10) Gigabit Ethernet NIC"
+ depends on PCI
+ help
+ This enables the support for NetXen's Gigabit Ethernet card.
+
endmenu
source "drivers/net/tokenring/Kconfig"
config RIONET
tristate "RapidIO Ethernet over messaging driver support"
- depends on NETDEVICES && RAPIDIO
+ depends on RAPIDIO
config RIONET_TX_SIZE
int "Number of outbound queue entries"
"SCSI generic support".
config SHAPER
- tristate "Traffic Shaper (EXPERIMENTAL)"
+ tristate "Traffic Shaper (OBSOLETE)"
depends on EXPERIMENTAL
---help---
The traffic shaper is a virtual network device that allows you to
these virtual devices. See
<file:Documentation/networking/shaper.txt> for more information.
- An alternative to this traffic shaper is the experimental
- Class-Based Queuing (CBQ) scheduling support which you get if you
- say Y to "QoS and/or fair queuing" above.
+ An alternative to this traffic shaper are traffic schedulers which
+ you'll get if you say Y to "QoS and/or fair queuing" in
+ "Networking options".
To compile this driver as a module, choose M here: the module
will be called shaper. If unsure, say N.
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff