This allows one to create virtual interfaces that map packets to
or from specific MAC addresses to a particular interface.
+ Macvlan devices can be added using the "ip" command from the
+ iproute2 package starting with the iproute2-2.6.23 release:
+
+ "ip link add link <real dev> [ address MAC ] [ NAME ] type macvlan"
+
To compile this driver as a module, choose M here: the module
will be called macvlan.
Say Y here to support the on-board Intel 82596 ethernet controller
built into SNI RM machines.
+config KORINA
+ tristate "Korina (IDT RC32434) Ethernet support"
+ depends on NET_ETHERNET && MIKROTIK_RB532
+ help
+ If you have a Mikrotik RouterBoard 500 or IDT RC32434
+ based system say Y. Otherwise say N.
+
config MIPS_JAZZ_SONIC
tristate "MIPS JAZZ onboard SONIC Ethernet support"
depends on MACH_JAZZ
If unsure, say N.
+config SH_ETH
+ tristate "Renesas SuperH Ethernet support"
+ depends on SUPERH && \
+ (CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712)
+ select CRC32
+ select MII
+ select MDIO_BITBANG
+ select PHYLIB
+ help
+ Renesas SuperH Ethernet device driver.
+ This driver support SH7710 and SH7712.
+
config SUNLANCE
tristate "Sun LANCE support"
depends on SBUS
will be called smc-ultra32.
config BFIN_MAC
- tristate "Blackfin 536/537 on-chip mac support"
- depends on NET_ETHERNET && (BF537 || BF536) && (!BF537_PORT_H)
+ tristate "Blackfin 527/536/537 on-chip mac support"
+ depends on NET_ETHERNET && (BF527 || BF537 || BF536)
select CRC32
select MII
select PHYLIB
config BFIN_MAC_USE_L1
bool "Use L1 memory for rx/tx packets"
- depends on BFIN_MAC && BF537
+ depends on BFIN_MAC && (BF527 || BF537)
default y
help
To get maximum network performance, you should use L1 memory as rx/tx buffers.
config BFIN_MAC_RMII
bool "RMII PHY Interface (EXPERIMENTAL)"
depends on BFIN_MAC && EXPERIMENTAL
- default n
+ default y if BFIN527_EZKIT
+ default n if BFIN537_STAMP
help
Use Reduced PHY MII Interface
tristate "SMC 91C9x/91C1xxx support"
select CRC32
select MII
- depends on ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || SOC_AU1X00 || BLACKFIN
+ depends on ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || \
+ SOC_AU1X00 || BLACKFIN || MN10300
help
This is a driver for SMC's 91x series of Ethernet chipsets,
including the SMC91C94 and the SMC91C111. Say Y if you want it
---help---
Support for the Microchip EN28J60 ethernet chip.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module will be
+ To compile this driver as a module, choose M here. The module will be
called enc28j60.
config ENC28J60_WRITEVERIFY
Enable the verify after the buffer write useful for debugging purpose.
If unsure, say N.
+config DM9000_DEBUGLEVEL
+ int "DM9000 maximum debug level"
+ depends on DM9000
+ default 4
+ help
+ The maximum level of debugging code compiled into the DM9000
+ driver.
+
config SMC911X
tristate "SMSC LAN911[5678] support"
select CRC32
select MII
- depends on ARCH_PXA || SH_MAGIC_PANEL_R2
+ depends on ARCH_PXA || SUPERH
help
This is a driver for SMSC's LAN911x series of Ethernet chipsets
including the new LAN9115, LAN9116, LAN9117, and LAN9118.
config IBMLANA
tristate "IBM LAN Adapter/A support"
- depends on MCA && MCA_LEGACY
+ depends on MCA
---help---
This is a Micro Channel Ethernet adapter. You need to set
CONFIG_MCA to use this driver. It is both available as an in-kernel
To compile this driver as a module, choose M here. The module will
be called ibmveth.
-source "drivers/net/ibm_emac/Kconfig"
source "drivers/net/ibm_newemac/Kconfig"
config NET_PCI
To compile this driver as a module, choose M here. The module
will be called pcnet32.
-config PCNET32_NAPI
- bool "Use RX polling (NAPI)"
- depends on PCNET32
- help
- NAPI is a new driver API designed to reduce CPU and interrupt load
- when the driver is receiving lots of packets from the card. It is
- still somewhat experimental and thus not yet enabled by default.
-
- If your estimated Rx load is 10kpps or more, or if the card will be
- deployed on potentially unfriendly networks (e.g. in a firewall),
- then say Y here.
-
- If in doubt, say N.
-
config AMD8111_ETH
tristate "AMD 8111 (new PCI lance) support"
depends on NET_PCI && PCI
config B44
tristate "Broadcom 440x/47xx ethernet support"
- depends on SSB_POSSIBLE
+ depends on SSB_POSSIBLE && HAS_DMA
select SSB
select MII
help
config TC35815
tristate "TOSHIBA TC35815 Ethernet support"
depends on NET_PCI && PCI && MIPS
- select MII
+ select PHYLIB
config EEPRO100
tristate "EtherExpressPro/100 support (eepro100, original Becker driver)"
config TLAN
tristate "TI ThunderLAN support"
- depends on NET_PCI && (PCI || EISA) && !64BIT
+ depends on NET_PCI && (PCI || EISA)
---help---
If you have a PCI Ethernet network card based on the ThunderLAN chip
which is supported by this driver, say Y and read the
config CPMAC
tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)"
- depends on NET_ETHERNET && EXPERIMENTAL && AR7
+ depends on NET_ETHERNET && EXPERIMENTAL && AR7 && BROKEN
select PHYLIB
- select FIXED_PHY
- select FIXED_MII_100_FDX
help
TI AR7 CPMAC Ethernet support
config E1000E
tristate "Intel(R) PRO/1000 PCI-Express Gigabit Ethernet support"
- depends on PCI
+ depends on PCI && (!SPARC32 || BROKEN)
---help---
This driver supports the PCI-Express Intel(R) PRO/1000 gigabit
ethernet family of adapters. For PCI or PCI-X e1000 adapters,
More specific information on configuring the driver is in
<file:Documentation/networking/e1000.txt>.
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module
+ To compile this driver as a module, choose M here. The module
will be called igb.
source "drivers/net/ixp2000/Kconfig"
If unsure, say N.
-config SK98LIN
- tristate "Marvell Yukon Chipset / SysKonnect SK-98xx Support (DEPRECATED)"
- depends on PCI
- ---help---
- Say Y here if you have a Marvell Yukon or SysKonnect SK-98xx/SK-95xx
- compliant Gigabit Ethernet Adapter.
-
- This driver supports the original Yukon chipset. This driver is
- deprecated and will be removed from the kernel in the near future,
- it has been replaced by the skge driver. skge is cleaner and
- seems to work better.
-
- This driver does not support the newer Yukon2 chipset. A separate
- driver, sky2, is provided to support Yukon2-based adapters.
-
- The following adapters are supported by this driver:
- - 3Com 3C940 Gigabit LOM Ethernet Adapter
- - 3Com 3C941 Gigabit LOM Ethernet Adapter
- - Allied Telesyn AT-2970LX Gigabit Ethernet Adapter
- - Allied Telesyn AT-2970LX/2SC Gigabit Ethernet Adapter
- - Allied Telesyn AT-2970SX Gigabit Ethernet Adapter
- - Allied Telesyn AT-2970SX/2SC Gigabit Ethernet Adapter
- - Allied Telesyn AT-2970TX Gigabit Ethernet Adapter
- - Allied Telesyn AT-2970TX/2TX Gigabit Ethernet Adapter
- - Allied Telesyn AT-2971SX Gigabit Ethernet Adapter
- - Allied Telesyn AT-2971T Gigabit Ethernet Adapter
- - Belkin Gigabit Desktop Card 10/100/1000Base-T Adapter, Copper RJ-45
- - EG1032 v2 Instant Gigabit Network Adapter
- - EG1064 v2 Instant Gigabit Network Adapter
- - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Abit)
- - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Albatron)
- - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Asus)
- - Marvell 88E8001 Gigabit LOM Ethernet Adapter (ECS)
- - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Epox)
- - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Foxconn)
- - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Gigabyte)
- - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Iwill)
- - Marvell 88E8050 Gigabit LOM Ethernet Adapter (Intel)
- - Marvell RDK-8001 Adapter
- - Marvell RDK-8002 Adapter
- - Marvell RDK-8003 Adapter
- - Marvell RDK-8004 Adapter
- - Marvell RDK-8006 Adapter
- - Marvell RDK-8007 Adapter
- - Marvell RDK-8008 Adapter
- - Marvell RDK-8009 Adapter
- - Marvell RDK-8010 Adapter
- - Marvell RDK-8011 Adapter
- - Marvell RDK-8012 Adapter
- - Marvell RDK-8052 Adapter
- - Marvell Yukon Gigabit Ethernet 10/100/1000Base-T Adapter (32 bit)
- - Marvell Yukon Gigabit Ethernet 10/100/1000Base-T Adapter (64 bit)
- - N-Way PCI-Bus Giga-Card 1000/100/10Mbps(L)
- - SK-9521 10/100/1000Base-T Adapter
- - SK-9521 V2.0 10/100/1000Base-T Adapter
- - SK-9821 Gigabit Ethernet Server Adapter (SK-NET GE-T)
- - SK-9821 V2.0 Gigabit Ethernet 10/100/1000Base-T Adapter
- - SK-9822 Gigabit Ethernet Server Adapter (SK-NET GE-T dual link)
- - SK-9841 Gigabit Ethernet Server Adapter (SK-NET GE-LX)
- - SK-9841 V2.0 Gigabit Ethernet 1000Base-LX Adapter
- - SK-9842 Gigabit Ethernet Server Adapter (SK-NET GE-LX dual link)
- - SK-9843 Gigabit Ethernet Server Adapter (SK-NET GE-SX)
- - SK-9843 V2.0 Gigabit Ethernet 1000Base-SX Adapter
- - SK-9844 Gigabit Ethernet Server Adapter (SK-NET GE-SX dual link)
- - SK-9851 V2.0 Gigabit Ethernet 1000Base-SX Adapter
- - SK-9861 Gigabit Ethernet Server Adapter (SK-NET GE-SX Volition)
- - SK-9861 V2.0 Gigabit Ethernet 1000Base-SX Adapter
- - SK-9862 Gigabit Ethernet Server Adapter (SK-NET GE-SX Volition dual link)
- - SK-9871 Gigabit Ethernet Server Adapter (SK-NET GE-ZX)
- - SK-9871 V2.0 Gigabit Ethernet 1000Base-ZX Adapter
- - SK-9872 Gigabit Ethernet Server Adapter (SK-NET GE-ZX dual link)
- - SMC EZ Card 1000 (SMC9452TXV.2)
-
- The adapters support Jumbo Frames.
- The dual link adapters support link-failover and dual port features.
- Both Marvell Yukon and SysKonnect SK-98xx/SK-95xx adapters support
- the scatter-gather functionality with sendfile(). Please refer to
- <file:Documentation/networking/sk98lin.txt> for more information about
- optional driver parameters.
- Questions concerning this driver may be addressed to:
- <linux@syskonnect.de>
-
- If you want to compile this driver as a module ( = code which can be
- inserted in and removed from the running kernel whenever you want),
- say M here and read <file:Documentation/kbuild/modules.txt>. The module will
- be called sk98lin. This is recommended.
-
config VIA_VELOCITY
tristate "VIA Velocity support"
depends on PCI
config TIGON3
tristate "Broadcom Tigon3 support"
depends on PCI
+ select PHYLIB
help
This driver supports Broadcom Tigon3 based gigabit Ethernet cards.
config GELIC_NET
tristate "PS3 Gigabit Ethernet driver"
depends on PPC_PS3
+ select PS3_SYS_MANAGER
help
This driver supports the network device on the PS3 game
console. This driver has built-in support for Ethernet.
To compile this driver as a module, choose M here: the
module will be called ps3_gelic.
+config GELIC_WIRELESS
+ bool "PS3 Wireless support"
+ depends on GELIC_NET
+ select WIRELESS_EXT
+ help
+ This option adds the support for the wireless feature of PS3.
+ If you have the wireless-less model of PS3 or have no plan to
+ use wireless feature, disabling this option saves memory. As
+ the driver automatically distinguishes the models, you can
+ safely enable this option even if you have a wireless-less model.
+
+config GELIC_WIRELESS_OLD_PSK_INTERFACE
+ bool "PS3 Wireless private PSK interface (OBSOLETE)"
+ depends on GELIC_WIRELESS
+ help
+ This option retains the obsolete private interface to pass
+ the PSK from user space programs to the driver. The PSK
+ stands for 'Pre Shared Key' and is used for WPA[2]-PSK
+ (WPA-Personal) environment.
+ If WPA[2]-PSK is used and you need to use old programs that
+ support only this old interface, say Y. Otherwise N.
+
+ If unsure, say N.
+
config GIANFAR
tristate "Gianfar Ethernet"
- depends on 85xx || 83xx || PPC_86xx
+ depends on FSL_SOC
select PHYLIB
select CRC32
help
config MV643XX_ETH
tristate "Marvell Discovery (643XX) and Orion ethernet support"
- depends on MV64360 || MV64X60 || (PPC_MULTIPLATFORM && PPC32) || ARCH_ORION
+ depends on MV64360 || MV64X60 || (PPC_MULTIPLATFORM && PPC32) || PLAT_ORION
select MII
help
This driver supports the gigabit ethernet MACs in the
config CHELSIO_T3
tristate "Chelsio Communications T3 10Gb Ethernet support"
- depends on PCI
+ depends on PCI && INET
select FW_LOADER
+ select INET_LRO
help
This driver supports Chelsio T3-based gigabit and 10Gb Ethernet
adapters.
config EHEA
tristate "eHEA Ethernet support"
- depends on IBMEBUS && INET
+ depends on IBMEBUS && INET && SPARSEMEM
select INET_LRO
---help---
This driver supports the IBM pSeries eHEA ethernet adapter.
config PASEMI_MAC
tristate "PA Semi 1/10Gbit MAC"
- depends on PPC64 && PCI
+ depends on PPC_PASEMI && PCI
select PHYLIB
select INET_LRO
help
To compile this driver as a module, choose M here: the module
will be called bnx2x. This is recommended.
+source "drivers/net/sfc/Kconfig"
endif # NETDEV_10000
tristate "Virtio network driver (EXPERIMENTAL)"
depends on EXPERIMENTAL && VIRTIO
---help---
- This is the virtual network driver for lguest. Say Y or M.
+ This is the virtual network driver for virtio. It can be used with
+ lguest or QEMU based VMMs (like KVM or Xen). Say Y or M.
endif # NETDEVICES
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff