410 Severn Ave., Suite 210
Annapolis MD 21403
- Linux Kernel Additions:
-
- 0.99H+lk0.9 - David S. Miller - softnet, PCI DMA updates
- 0.99H+lk1.0 - Jeff Garzik <jgarzik@pobox.com>
- Remove compatibility defines for kernel versions < 2.2.x.
- Update for new 2.3.x module interface
- LK1.1.2 (March 19, 2000)
- * New PCI interface (jgarzik)
-
- LK1.1.3 25 April 2000, Andrew Morton <andrewm@uow.edu.au>
- - Merged with 3c575_cb.c
- - Don't set RxComplete in boomerang interrupt enable reg
- - spinlock in vortex_timer to protect mdio functions
- - disable local interrupts around call to vortex_interrupt in
- vortex_tx_timeout() (So vortex_interrupt can use spin_lock())
- - Select window 3 in vortex_timer()'s write to Wn3_MAC_Ctrl
- - In vortex_start_xmit(), move the lock to _after_ we've altered
- vp->cur_tx and vp->tx_full. This defeats the race between
- vortex_start_xmit() and vortex_interrupt which was identified
- by Bogdan Costescu.
- - Merged back support for six new cards from various sources
- - Set vortex_have_pci if pci_module_init returns zero (fixes cardbus
- insertion oops)
- - Tell it that 3c905C has NWAY for 100bT autoneg
- - Fix handling of SetStatusEnd in 'Too much work..' code, as
- per 2.3.99's 3c575_cb (Dave Hinds).
- - Split ISR into two for vortex & boomerang
- - Fix MOD_INC/DEC races
- - Handle resource allocation failures.
- - Fix 3CCFE575CT LED polarity
- - Make tx_interrupt_mitigation the default
-
- LK1.1.4 25 April 2000, Andrew Morton <andrewm@uow.edu.au>
- - Add extra TxReset to vortex_up() to fix 575_cb hotplug initialisation probs.
- - Put vortex_info_tbl into __devinitdata
- - In the vortex_error StatsFull HACK, disable stats in vp->intr_enable as well
- as in the hardware.
- - Increased the loop counter in issue_and_wait from 2,000 to 4,000.
-
- LK1.1.5 28 April 2000, andrewm
- - Added powerpc defines (John Daniel <jdaniel@etresoft.com> said these work...)
- - Some extra diagnostics
- - In vortex_error(), reset the Tx on maxCollisions. Otherwise most
- chips usually get a Tx timeout.
- - Added extra_reset module parm
- - Replaced some inline timer manip with mod_timer
- (Franois romieu <Francois.Romieu@nic.fr>)
- - In vortex_up(), don't make Wn3_config initialisation dependent upon has_nway
- (this came across from 3c575_cb).
-
- LK1.1.6 06 Jun 2000, andrewm
- - Backed out the PPC defines.
- - Use del_timer_sync(), mod_timer().
- - Fix wrapped ulong comparison in boomerang_rx()
- - Add IS_TORNADO, use it to suppress 3c905C checksum error msg
- (Donald Becker, I Lee Hetherington <ilh@sls.lcs.mit.edu>)
- - Replace union wn3_config with BFINS/BFEXT manipulation for
- sparc64 (Pete Zaitcev, Peter Jones)
- - In vortex_error, do_tx_reset and vortex_tx_timeout(Vortex):
- do a netif_wake_queue() to better recover from errors. (Anders Pedersen,
- Donald Becker)
- - Print a warning on out-of-memory (rate limited to 1 per 10 secs)
- - Added two more Cardbus 575 NICs: 5b57 and 6564 (Paul Wagland)
-
- LK1.1.7 2 Jul 2000 andrewm
- - Better handling of shared IRQs
- - Reset the transmitter on a Tx reclaim error
- - Fixed crash under OOM during vortex_open() (Mark Hemment)
- - Fix Rx cessation problem during OOM (help from Mark Hemment)
- - The spinlocks around the mdio access were blocking interrupts for 300uS.
- Fix all this to use spin_lock_bh() within mdio_read/write
- - Only write to TxFreeThreshold if it's a boomerang - other NICs don't
- have one.
- - Added 802.3x MAC-layer flow control support
-
- LK1.1.8 13 Aug 2000 andrewm
- - Ignore request_region() return value - already reserved if Cardbus.
- - Merged some additional Cardbus flags from Don's 0.99Qk
- - Some fixes for 3c556 (Fred Maciel)
- - Fix for EISA initialisation (Jan Rekorajski)
- - Renamed MII_XCVR_PWR and EEPROM_230 to align with 3c575_cb and D. Becker's drivers
- - Fixed MII_XCVR_PWR for 3CCFE575CT
- - Added INVERT_LED_PWR, used it.
- - Backed out the extra_reset stuff
-
- LK1.1.9 12 Sep 2000 andrewm
- - Backed out the tx_reset_resume flags. It was a no-op.
- - In vortex_error, don't reset the Tx on txReclaim errors
- - In vortex_error, don't reset the Tx on maxCollisions errors.
- Hence backed out all the DownListPtr logic here.
- - In vortex_error, give Tornado cards a partial TxReset on
- maxCollisions (David Hinds). Defined MAX_COLLISION_RESET for this.
- - Redid some driver flags and device names based on pcmcia_cs-3.1.20.
- - Fixed a bug where, if vp->tx_full is set when the interface
- is downed, it remains set when the interface is upped. Bad
- things happen.
-
- LK1.1.10 17 Sep 2000 andrewm
- - Added EEPROM_8BIT for 3c555 (Fred Maciel)
- - Added experimental support for the 3c556B Laptop Hurricane (Louis Gerbarg)
- - Add HAS_NWAY to "3c900 Cyclone 10Mbps TPO"
-
- LK1.1.11 13 Nov 2000 andrewm
- - Dump MOD_INC/DEC_USE_COUNT, use SET_MODULE_OWNER
-
- LK1.1.12 1 Jan 2001 andrewm (2.4.0-pre1)
- - Call pci_enable_device before we request our IRQ (Tobias Ringstrom)
- - Add 3c590 PCI latency timer hack to vortex_probe1 (from 0.99Ra)
- - Added extended issue_and_wait for the 3c905CX.
- - Look for an MII on PHY index 24 first (3c905CX oddity).
- - Add HAS_NWAY to 3cSOHO100-TX (Brett Frankenberger)
- - Don't free skbs we don't own on oom path in vortex_open().
-
- LK1.1.13 27 Jan 2001
- - Added explicit `medialock' flag so we can truly
- lock the media type down with `options'.
- - "check ioremap return and some tidbits" (Arnaldo Carvalho de Melo <acme@conectiva.com.br>)
- - Added and used EEPROM_NORESET for 3c556B PM resumes.
- - Fixed leakage of vp->rx_ring.
- - Break out separate HAS_HWCKSM device capability flag.
- - Kill vp->tx_full (ANK)
- - Merge zerocopy fragment handling (ANK?)
-
- LK1.1.14 15 Feb 2001
- - Enable WOL. Can be turned on with `enable_wol' module option.
- - EISA and PCI initialisation fixes (jgarzik, Manfred Spraul)
- - If a device's internalconfig register reports it has NWAY,
- use it, even if autoselect is enabled.
-
- LK1.1.15 6 June 2001 akpm
- - Prevent double counting of received bytes (Lars Christensen)
- - Add ethtool support (jgarzik)
- - Add module parm descriptions (Andrzej M. Krzysztofowicz)
- - Implemented alloc_etherdev() API
- - Special-case the 'Tx error 82' message.
-
- LK1.1.16 18 July 2001 akpm
- - Make NETIF_F_SG dependent upon nr_free_highpages(), not on CONFIG_HIGHMEM
- - Lessen verbosity of bootup messages
- - Fix WOL - use new PM API functions.
- - Use netif_running() instead of vp->open in suspend/resume.
- - Don't reset the interface logic on open/close/rmmod. It upsets
- autonegotiation, and hence DHCP (from 0.99T).
- - Back out EEPROM_NORESET flag because of the above (we do it for all
- NICs).
- - Correct 3c982 identification string
- - Rename wait_for_completion() to issue_and_wait() to avoid completion.h
- clash.
-
- LK1.1.17 18Dec01 akpm
- - PCI ID 9805 is a Python-T, not a dual-port Cyclone. Apparently.
- And it has NWAY.
- - Mask our advertised modes (vp->advertising) with our capabilities
- (MII reg5) when deciding which duplex mode to use.
- - Add `global_options' as default for options[]. Ditto global_enable_wol,
- global_full_duplex.
-
- LK1.1.18 01Jul02 akpm
- - Fix for undocumented transceiver power-up bit on some 3c566B's
- (Donald Becker, Rahul Karnik)
-
- - See http://www.zip.com.au/~akpm/linux/#3c59x-2.3 for more details.
- - Also see Documentation/networking/vortex.txt
-
- LK1.1.19 10Nov02 Marc Zyngier <maz@wild-wind.fr.eu.org>
- - EISA sysfs integration.
*/
/*
static int boomerang_start_xmit(struct sk_buff *skb, struct net_device *dev);
static int vortex_rx(struct net_device *dev);
static int boomerang_rx(struct net_device *dev);
-static irqreturn_t vortex_interrupt(int irq, void *dev_id, struct pt_regs *regs);
-static irqreturn_t boomerang_interrupt(int irq, void *dev_id, struct pt_regs *regs);
+static irqreturn_t vortex_interrupt(int irq, void *dev_id);
+static irqreturn_t boomerang_interrupt(int irq, void *dev_id);
static int vortex_close(struct net_device *dev);
static void dump_tx_ring(struct net_device *dev);
static void update_stats(void __iomem *ioaddr, struct net_device *dev);
#endif
static void vortex_tx_timeout(struct net_device *dev);
static void acpi_set_WOL(struct net_device *dev);
-static struct ethtool_ops vortex_ethtool_ops;
+static const struct ethtool_ops vortex_ethtool_ops;
static void set_8021q_mode(struct net_device *dev, int enable);
/* This driver uses 'options' to pass the media type, full-duplex flag, etc. */
{
struct vortex_private *vp = netdev_priv(dev);
unsigned long flags;
- local_save_flags(flags);
- local_irq_disable();
- (vp->full_bus_master_rx ? boomerang_interrupt:vortex_interrupt)(dev->irq,dev,NULL);
+ local_irq_save(flags);
+ (vp->full_bus_master_rx ? boomerang_interrupt:vortex_interrupt)(dev->irq,dev);
local_irq_restore(flags);
-}
+}
#endif
#ifdef CONFIG_PM
pci_enable_device(pdev);
pci_set_master(pdev);
if (request_irq(dev->irq, vp->full_bus_master_rx ?
- &boomerang_interrupt : &vortex_interrupt, SA_SHIRQ, dev->name, dev)) {
+ &boomerang_interrupt : &vortex_interrupt, IRQF_SHARED, dev->name, dev)) {
printk(KERN_WARNING "%s: Could not reserve IRQ %d\n", dev->name, dev->irq);
pci_disable_device(pdev);
return -EBUSY;
{ "TCM5970", CH_3C597 },
{ "" }
};
+MODULE_DEVICE_TABLE(eisa, vortex_eisa_ids);
static int vortex_eisa_probe(struct device *device);
static int vortex_eisa_remove(struct device *device);
vp = netdev_priv(dev);
ioaddr = vp->ioaddr;
-
+
unregister_netdev(dev);
iowrite16(TotalReset|0x14, ioaddr + EL3_CMD);
release_region(dev->base_addr, VORTEX_TOTAL_SIZE);
eisa_found = 1;
}
#endif
-
+
/* Special code to work-around the Compaq PCI BIOS32 problem. */
if (compaq_ioaddr) {
vortex_probe1(NULL, ioport_map(compaq_ioaddr, VORTEX_TOTAL_SIZE),
struct vortex_chip_info *vci;
void __iomem *ioaddr;
- /* wake up and enable device */
+ /* wake up and enable device */
rc = pci_enable_device(pdev);
if (rc < 0)
goto out;
if (request_region(dev->base_addr, vci->io_size, print_name) != NULL)
vp->must_free_region = 1;
- /* enable bus-mastering if necessary */
+ /* enable bus-mastering if necessary */
if (vci->flags & PCI_USES_MASTER)
pci_set_master(pdev);
vp->tx_ring_dma = vp->rx_ring_dma + sizeof(struct boom_rx_desc) * RX_RING_SIZE;
/* if we are a PCI driver, we store info in pdev->driver_data
- * instead of a module list */
+ * instead of a module list */
if (pdev)
pci_set_drvdata(pdev, dev);
if (edev)
dev->tx_timeout = vortex_tx_timeout;
dev->watchdog_timeo = (watchdog * HZ) / 1000;
#ifdef CONFIG_NET_POLL_CONTROLLER
- dev->poll_controller = poll_vortex;
+ dev->poll_controller = poll_vortex;
#endif
if (pdev) {
vp->pm_state_valid = 1;
/* Use the now-standard shared IRQ implementation. */
if ((retval = request_irq(dev->irq, vp->full_bus_master_rx ?
- &boomerang_interrupt : &vortex_interrupt, SA_SHIRQ, dev->name, dev))) {
+ &boomerang_interrupt : &vortex_interrupt, IRQF_SHARED, dev->name, dev))) {
printk(KERN_ERR "%s: Could not reserve IRQ %d\n", dev->name, dev->irq);
goto out;
}
printk(KERN_DEBUG "dev->watchdog_timeo=%d\n", dev->watchdog_timeo);
}
- disable_irq(dev->irq);
+ disable_irq_lockdep(dev->irq);
old_window = ioread16(ioaddr + EL3_CMD) >> 13;
EL3WINDOW(4);
media_status = ioread16(ioaddr + Wn4_Media);
dev->name, media_tbl[dev->if_port].name);
EL3WINDOW(old_window);
- enable_irq(dev->irq);
+ enable_irq_lockdep(dev->irq);
mod_timer(&vp->timer, RUN_AT(next_tick));
if (vp->deferred)
iowrite16(FakeIntr, ioaddr + EL3_CMD);
unsigned long flags;
local_irq_save(flags);
if (vp->full_bus_master_tx)
- boomerang_interrupt(dev->irq, dev, NULL);
+ boomerang_interrupt(dev->irq, dev);
else
- vortex_interrupt(dev->irq, dev, NULL);
+ vortex_interrupt(dev->irq, dev);
local_irq_restore(flags);
}
}
vp->stats.tx_dropped++;
netif_wake_queue(dev);
}
-
+
/* Issue Tx Enable */
iowrite16(TxEnable, ioaddr + EL3_CMD);
dev->trans_start = jiffies;
-
+
/* Switch to register set 7 for normal use. */
EL3WINDOW(7);
}
vp->tx_ring[entry].next = 0;
#if DO_ZEROCOPY
- if (skb->ip_summed != CHECKSUM_HW)
+ if (skb->ip_summed != CHECKSUM_PARTIAL)
vp->tx_ring[entry].status = cpu_to_le32(skb->len | TxIntrUploaded);
else
vp->tx_ring[entry].status = cpu_to_le32(skb->len | TxIntrUploaded | AddTCPChksum | AddUDPChksum);
*/
static irqreturn_t
-vortex_interrupt(int irq, void *dev_id, struct pt_regs *regs)
+vortex_interrupt(int irq, void *dev_id)
{
struct net_device *dev = dev_id;
struct vortex_private *vp = netdev_priv(dev);
*/
static irqreturn_t
-boomerang_interrupt(int irq, void *dev_id, struct pt_regs *regs)
+boomerang_interrupt(int irq, void *dev_id)
{
struct net_device *dev = dev_id;
struct vortex_private *vp = netdev_priv(dev);
if ((vp->tx_ring[entry].status & DN_COMPLETE) == 0)
break; /* It still hasn't been processed. */
#endif
-
+
if (vp->tx_skbuff[entry]) {
struct sk_buff *skb = vp->tx_skbuff[entry];
-#if DO_ZEROCOPY
+#if DO_ZEROCOPY
int i;
for (i=0; i<=skb_shinfo(skb)->nr_frags; i++)
pci_unmap_single(VORTEX_PCI(vp),
"not using them!\n", dev->name);
}
#endif
-
+
free_irq(dev->irq, dev);
if (vp->full_bus_master_rx) { /* Free Boomerang bus master Rx buffers. */
if (vortex_debug > 0) {
struct vortex_private *vp = netdev_priv(dev);
void __iomem *ioaddr = vp->ioaddr;
-
+
if (vp->full_bus_master_tx) {
int i;
int stalled = ioread32(ioaddr + PktStatus) & 0x04; /* Possible racy. But it's only debug stuff */
}
}
-static struct ethtool_ops vortex_ethtool_ops = {
+static const struct ethtool_ops vortex_ethtool_ops = {
.get_drvinfo = vortex_get_drvinfo,
.get_strings = vortex_get_strings,
.get_msglevel = vortex_get_msglevel,
int new_mode;
if (dev->flags & IFF_PROMISC) {
- if (vortex_debug > 0)
+ if (vortex_debug > 3)
printk(KERN_NOTICE "%s: Setting promiscuous mode.\n", dev->name);
new_mode = SetRxFilter|RxStation|RxMulticast|RxBroadcast|RxProm;
} else if ((dev->mc_list) || (dev->flags & IFF_ALLMULTI)) {
{
int pci_rc, eisa_rc;
- pci_rc = pci_module_init(&vortex_driver);
+ pci_rc = pci_register_driver(&vortex_driver);
eisa_rc = vortex_eisa_init();
if (pci_rc == 0)
/* Take care of the EISA devices */
eisa_driver_unregister(&vortex_eisa_driver);
#endif
-
+
if (compaq_net_device) {
vp = compaq_net_device->priv;
ioaddr = ioport_map(compaq_net_device->base_addr,
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff