static ushort id_read_eeprom(int index);
static ushort read_eeprom(int ioaddr, int index);
static int el3_open(struct net_device *dev);
-static int el3_start_xmit(struct sk_buff *skb, struct net_device *dev);
+static netdev_tx_t el3_start_xmit(struct sk_buff *skb, struct net_device *dev);
static irqreturn_t el3_interrupt(int irq, void *dev_id);
static void update_stats(struct net_device *dev);
static struct net_device_stats *el3_get_stats(struct net_device *dev);
&& !memcmp(phys_addr, el3_devs[i]->dev_addr,
ETH_ALEN)) {
if (el3_debug > 3)
- printk(KERN_DEBUG "3c509 with address %02x %02x %02x %02x %02x %02x was found by ISAPnP\n",
+ pr_debug("3c509 with address %02x %02x %02x %02x %02x %02x was found by ISAPnP\n",
phys_addr[0] & 0xff, phys_addr[0] >> 8,
phys_addr[1] & 0xff, phys_addr[1] >> 8,
phys_addr[2] & 0xff, phys_addr[2] >> 8);
#ifdef CONFIG_EISA
static struct eisa_device_id el3_eisa_ids[] = {
+ { "TCM5090" },
+ { "TCM5091" },
{ "TCM5092" },
{ "TCM5093" },
+ { "TCM5094" },
{ "TCM5095" },
+ { "TCM5098" },
{ "" }
};
MODULE_DEVICE_TABLE(eisa, el3_eisa_ids);
err = register_netdev(dev);
if (err) {
- printk(KERN_ERR "Failed to register 3c5x9 at %#3.3lx, IRQ %d.\n",
+ pr_err("Failed to register 3c5x9 at %#3.3lx, IRQ %d.\n",
dev->base_addr, dev->irq);
release_region(dev->base_addr, EL3_IO_EXTENT);
return err;
}
- printk(KERN_INFO "%s: 3c5x9 found at %#3.3lx, %s port, "
- "address %pM, IRQ %d.\n",
+ pr_info("%s: 3c5x9 found at %#3.3lx, %s port, address %pM, IRQ %d.\n",
dev->name, dev->base_addr, if_names[(dev->if_port & 0x03)],
dev->dev_addr, dev->irq);
if (el3_debug > 0)
- printk(KERN_INFO "%s", version);
+ pr_info("%s", version);
return 0;
}
irq = pos5 & 0x0f;
- printk(KERN_INFO "3c529: found %s at slot %d\n",
- el3_mca_adapter_names[mdev->index], slot + 1);
+ pr_info("3c529: found %s at slot %d\n",
+ el3_mca_adapter_names[mdev->index], slot + 1);
/* claim the slot */
strncpy(mdev->name, el3_mca_adapter_names[mdev->index],
irq = mca_device_transform_irq(mdev, irq);
ioaddr = mca_device_transform_ioport(mdev, ioaddr);
if (el3_debug > 2) {
- printk(KERN_DEBUG "3c529: irq %d ioaddr 0x%x ifport %d\n", irq, ioaddr, if_port);
+ pr_debug("3c529: irq %d ioaddr 0x%x ifport %d\n", irq, ioaddr, if_port);
}
EL3WINDOW(0);
for (i = 0; i < 3; i++)
netdev_boot_setup_check(dev);
el3_dev_fill(dev, phys_addr, ioaddr, irq, if_port, EL3_MCA);
- device->driver_data = dev;
+ dev_set_drvdata(device, dev);
err = el3_common_init(dev);
if (err) {
- device->driver_data = NULL;
+ dev_set_drvdata(device, NULL);
free_netdev(dev);
return -ENOMEM;
}
/* This remove works for all device types.
*
- * The net dev must be stored in the driver_data field */
+ * The net dev must be stored in the driver data field */
static int __devexit el3_device_remove (struct device *device)
{
struct net_device *dev;
- dev = device->driver_data;
+ dev = dev_get_drvdata(device);
el3_common_remove (dev);
return 0;
word = (word << 1) + (inb(id_port) & 0x01);
if (el3_debug > 3)
- printk(KERN_DEBUG " 3c509 EEPROM word %d %#4.4x.\n", index, word);
+ pr_debug(" 3c509 EEPROM word %d %#4.4x.\n", index, word);
return word;
}
EL3WINDOW(0);
if (el3_debug > 3)
- printk(KERN_DEBUG "%s: Opening, IRQ %d status@%x %4.4x.\n", dev->name,
+ pr_debug("%s: Opening, IRQ %d status@%x %4.4x.\n", dev->name,
dev->irq, ioaddr + EL3_STATUS, inw(ioaddr + EL3_STATUS));
el3_up(dev);
if (el3_debug > 3)
- printk(KERN_DEBUG "%s: Opened 3c509 IRQ %d status %4.4x.\n",
+ pr_debug("%s: Opened 3c509 IRQ %d status %4.4x.\n",
dev->name, dev->irq, inw(ioaddr + EL3_STATUS));
return 0;
int ioaddr = dev->base_addr;
/* Transmitter timeout, serious problems. */
- printk(KERN_WARNING "%s: transmit timed out, Tx_status %2.2x status %4.4x "
- "Tx FIFO room %d.\n",
+ pr_warning("%s: transmit timed out, Tx_status %2.2x status %4.4x Tx FIFO room %d.\n",
dev->name, inb(ioaddr + TX_STATUS), inw(ioaddr + EL3_STATUS),
inw(ioaddr + TX_FREE));
dev->stats.tx_errors++;
}
-static int
+static netdev_tx_t
el3_start_xmit(struct sk_buff *skb, struct net_device *dev)
{
struct el3_private *lp = netdev_priv(dev);
dev->stats.tx_bytes += skb->len;
if (el3_debug > 4) {
- printk(KERN_DEBUG "%s: el3_start_xmit(length = %u) called, status %4.4x.\n",
+ pr_debug("%s: el3_start_xmit(length = %u) called, status %4.4x.\n",
dev->name, skb->len, inw(ioaddr + EL3_STATUS));
}
#if 0
ushort status = inw(ioaddr + EL3_STATUS);
if (status & 0x0001 /* IRQ line active, missed one. */
&& inw(ioaddr + EL3_STATUS) & 1) { /* Make sure. */
- printk(KERN_DEBUG "%s: Missed interrupt, status then %04x now %04x"
+ pr_debug("%s: Missed interrupt, status then %04x now %04x"
" Tx %2.2x Rx %4.4x.\n", dev->name, status,
inw(ioaddr + EL3_STATUS), inb(ioaddr + TX_STATUS),
inw(ioaddr + RX_STATUS));
outb(0x00, ioaddr + TX_STATUS); /* Pop the status stack. */
}
}
- return 0;
+ return NETDEV_TX_OK;
}
/* The EL3 interrupt handler. */
if (el3_debug > 4) {
status = inw(ioaddr + EL3_STATUS);
- printk(KERN_DEBUG "%s: interrupt, status %4.4x.\n", dev->name, status);
+ pr_debug("%s: interrupt, status %4.4x.\n", dev->name, status);
}
while ((status = inw(ioaddr + EL3_STATUS)) &
if (status & TxAvailable) {
if (el3_debug > 5)
- printk(KERN_DEBUG " TX room bit was handled.\n");
+ pr_debug(" TX room bit was handled.\n");
/* There's room in the FIFO for a full-sized packet. */
outw(AckIntr | TxAvailable, ioaddr + EL3_CMD);
netif_wake_queue (dev);
}
if (--i < 0) {
- printk(KERN_ERR "%s: Infinite loop in interrupt, status %4.4x.\n",
+ pr_err("%s: Infinite loop in interrupt, status %4.4x.\n",
dev->name, status);
/* Clear all interrupts. */
outw(AckIntr | 0xFF, ioaddr + EL3_CMD);
}
if (el3_debug > 4) {
- printk(KERN_DEBUG "%s: exiting interrupt, status %4.4x.\n", dev->name,
+ pr_debug("%s: exiting interrupt, status %4.4x.\n", dev->name,
inw(ioaddr + EL3_STATUS));
}
spin_unlock(&lp->lock);
int ioaddr = dev->base_addr;
if (el3_debug > 5)
- printk(" Updating the statistics.\n");
+ pr_debug(" Updating the statistics.\n");
/* Turn off statistics updates while reading. */
outw(StatsDisable, ioaddr + EL3_CMD);
/* Switch to the stats window, and read everything. */
short rx_status;
if (el3_debug > 5)
- printk(" In rx_packet(), status %4.4x, rx_status %4.4x.\n",
+ pr_debug(" In rx_packet(), status %4.4x, rx_status %4.4x.\n",
inw(ioaddr+EL3_STATUS), inw(ioaddr+RX_STATUS));
while ((rx_status = inw(ioaddr + RX_STATUS)) > 0) {
if (rx_status & 0x4000) { /* Error, update stats. */
skb = dev_alloc_skb(pkt_len+5);
if (el3_debug > 4)
- printk("Receiving packet size %d status %4.4x.\n",
+ pr_debug("Receiving packet size %d status %4.4x.\n",
pkt_len, rx_status);
if (skb != NULL) {
skb_reserve(skb, 2); /* Align IP on 16 byte */
outw(RxDiscard, ioaddr + EL3_CMD);
dev->stats.rx_dropped++;
if (el3_debug)
- printk("%s: Couldn't allocate a sk_buff of size %d.\n",
+ pr_debug("%s: Couldn't allocate a sk_buff of size %d.\n",
dev->name, pkt_len);
}
inw(ioaddr + EL3_STATUS); /* Delay. */
while (inw(ioaddr + EL3_STATUS) & 0x1000)
- printk(KERN_DEBUG " Waiting for 3c509 to discard packet, status %x.\n",
+ pr_debug(" Waiting for 3c509 to discard packet, status %x.\n",
inw(ioaddr + EL3_STATUS) );
}
static int old;
if (old != dev->mc_count) {
old = dev->mc_count;
- printk("%s: Setting Rx mode to %d addresses.\n", dev->name, dev->mc_count);
+ pr_debug("%s: Setting Rx mode to %d addresses.\n", dev->name, dev->mc_count);
}
}
spin_lock_irqsave(&lp->lock, flags);
struct el3_private *lp = netdev_priv(dev);
if (el3_debug > 2)
- printk("%s: Shutting down ethercard.\n", dev->name);
+ pr_debug("%s: Shutting down ethercard.\n", dev->name);
el3_down(dev);
EL3WINDOW(4);
net_diag = inw(ioaddr + WN4_NETDIAG);
net_diag = (net_diag | FD_ENABLE); /* temporarily assume full-duplex will be set */
- printk("%s: ", dev->name);
+ pr_info("%s: ", dev->name);
switch (dev->if_port & 0x0c) {
case 12:
/* force full-duplex mode if 3c5x9b */
if (sw_info & 0x000f) {
- printk("Forcing 3c5x9b full-duplex mode");
+ pr_cont("Forcing 3c5x9b full-duplex mode");
break;
}
case 8:
/* set full-duplex mode based on eeprom config setting */
if ((sw_info & 0x000f) && (sw_info & 0x8000)) {
- printk("Setting 3c5x9b full-duplex mode (from EEPROM configuration bit)");
+ pr_cont("Setting 3c5x9b full-duplex mode (from EEPROM configuration bit)");
break;
}
default:
/* xcvr=(0 || 4) OR user has an old 3c5x9 non "B" model */
- printk("Setting 3c5x9/3c5x9B half-duplex mode");
+ pr_cont("Setting 3c5x9/3c5x9B half-duplex mode");
net_diag = (net_diag & ~FD_ENABLE); /* disable full duplex */
}
outw(net_diag, ioaddr + WN4_NETDIAG);
- printk(" if_port: %d, sw_info: %4.4x\n", dev->if_port, sw_info);
+ pr_cont(" if_port: %d, sw_info: %4.4x\n", dev->if_port, sw_info);
if (el3_debug > 3)
- printk("%s: 3c5x9 net diag word is now: %4.4x.\n", dev->name, net_diag);
+ pr_debug("%s: 3c5x9 net diag word is now: %4.4x.\n", dev->name, net_diag);
/* Enable link beat and jabber check. */
outw(inw(ioaddr + WN4_MEDIA) | MEDIA_TP, ioaddr + WN4_MEDIA);
}
struct el3_private *lp;
int ioaddr;
- dev = pdev->driver_data;
+ dev = dev_get_drvdata(pdev);
lp = netdev_priv(dev);
ioaddr = dev->base_addr;
struct el3_private *lp;
int ioaddr;
- dev = pdev->driver_data;
+ dev = dev_get_drvdata(pdev);
lp = netdev_priv(dev);
ioaddr = dev->base_addr;
}
if (id_port >= 0x200) {
id_port = 0;
- printk(KERN_ERR "No I/O port available for 3c509 activation.\n");
+ pr_err("No I/O port available for 3c509 activation.\n");
} else {
ret = isa_register_driver(&el3_isa_driver, EL3_MAX_CARDS);
if (!ret)
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff