.eccbytes = 3,
.eccpos = {6, 7, 8},
.oobfree = { {0, 5}, {9, 7} },
- .oobavail = 12,
};
/* Small Page FLASH with FMR[ECCM] = 1 */
.eccbytes = 3,
.eccpos = {8, 9, 10},
.oobfree = { {0, 5}, {6, 2}, {11, 5} },
- .oobavail = 12,
};
/* Large Page FLASH with FMR[ECCM] = 0 */
.eccbytes = 12,
.eccpos = {6, 7, 8, 22, 23, 24, 38, 39, 40, 54, 55, 56},
.oobfree = { {1, 5}, {9, 13}, {25, 13}, {41, 13}, {57, 7} },
- .oobavail = 48,
};
/* Large Page FLASH with FMR[ECCM] = 1 */
.eccbytes = 12,
.eccpos = {8, 9, 10, 24, 25, 26, 40, 41, 42, 56, 57, 58},
.oobfree = { {1, 7}, {11, 13}, {27, 13}, {43, 13}, {59, 5} },
- .oobavail = 48,
+};
+
+/*
+ * fsl_elbc_oob_lp_eccm* specify that LP NAND's OOB free area starts at offset
+ * 1, so we have to adjust bad block pattern. This pattern should be used for
+ * x8 chips only. So far hardware does not support x16 chips anyway.
+ */
+static u8 scan_ff_pattern[] = { 0xff, };
+
+static struct nand_bbt_descr largepage_memorybased = {
+ .options = 0,
+ .offs = 0,
+ .len = 1,
+ .pattern = scan_ff_pattern,
+};
+
+/*
+ * ELBC may use HW ECC, so that OOB offsets, that NAND core uses for bbt,
+ * interfere with ECC positions, that's why we implement our own descriptors.
+ * OOB {11, 5}, works for both SP and LP chips, with ECCM = 1 and ECCM = 0.
+ */
+static u8 bbt_pattern[] = {'B', 'b', 't', '0' };
+static u8 mirror_pattern[] = {'1', 't', 'b', 'B' };
+
+static struct nand_bbt_descr bbt_main_descr = {
+ .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE |
+ NAND_BBT_2BIT | NAND_BBT_VERSION,
+ .offs = 11,
+ .len = 4,
+ .veroffs = 15,
+ .maxblocks = 4,
+ .pattern = bbt_pattern,
+};
+
+static struct nand_bbt_descr bbt_mirror_descr = {
+ .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE |
+ NAND_BBT_2BIT | NAND_BBT_VERSION,
+ .offs = 11,
+ .len = 4,
+ .veroffs = 15,
+ .maxblocks = 4,
+ .pattern = mirror_pattern,
};
/*=================================*/
ctrl->use_mdr = 0;
- dev_vdbg(ctrl->dev,
- "fsl_elbc_run_command: stat=%08x mdr=%08x fmr=%08x\n",
- ctrl->status, ctrl->mdr, in_be32(&lbc->fmr));
+ if (ctrl->status != LTESR_CC) {
+ dev_info(ctrl->dev,
+ "command failed: fir %x fcr %x status %x mdr %x\n",
+ in_be32(&lbc->fir), in_be32(&lbc->fcr),
+ ctrl->status, ctrl->mdr);
+ return -EIO;
+ }
- /* returns 0 on success otherwise non-zero) */
- return ctrl->status == LTESR_CC ? 0 : -EIO;
+ return 0;
}
static void fsl_elbc_do_read(struct nand_chip *chip, int oob)
if (priv->page_size) {
out_be32(&lbc->fir,
- (FIR_OP_CW0 << FIR_OP0_SHIFT) |
+ (FIR_OP_CM0 << FIR_OP0_SHIFT) |
(FIR_OP_CA << FIR_OP1_SHIFT) |
(FIR_OP_PA << FIR_OP2_SHIFT) |
- (FIR_OP_CW1 << FIR_OP3_SHIFT) |
+ (FIR_OP_CM1 << FIR_OP3_SHIFT) |
(FIR_OP_RBW << FIR_OP4_SHIFT));
out_be32(&lbc->fcr, (NAND_CMD_READ0 << FCR_CMD0_SHIFT) |
(NAND_CMD_READSTART << FCR_CMD1_SHIFT));
} else {
out_be32(&lbc->fir,
- (FIR_OP_CW0 << FIR_OP0_SHIFT) |
+ (FIR_OP_CM0 << FIR_OP0_SHIFT) |
(FIR_OP_CA << FIR_OP1_SHIFT) |
(FIR_OP_PA << FIR_OP2_SHIFT) |
(FIR_OP_RBW << FIR_OP3_SHIFT));
case NAND_CMD_READID:
dev_vdbg(ctrl->dev, "fsl_elbc_cmdfunc: NAND_CMD_READID.\n");
- out_be32(&lbc->fir, (FIR_OP_CW0 << FIR_OP0_SHIFT) |
+ out_be32(&lbc->fir, (FIR_OP_CM0 << FIR_OP0_SHIFT) |
(FIR_OP_UA << FIR_OP1_SHIFT) |
(FIR_OP_RBW << FIR_OP2_SHIFT));
out_be32(&lbc->fcr, NAND_CMD_READID << FCR_CMD0_SHIFT);
dev_vdbg(ctrl->dev, "fsl_elbc_cmdfunc: NAND_CMD_ERASE2.\n");
out_be32(&lbc->fir,
- (FIR_OP_CW0 << FIR_OP0_SHIFT) |
+ (FIR_OP_CM0 << FIR_OP0_SHIFT) |
(FIR_OP_PA << FIR_OP1_SHIFT) |
- (FIR_OP_CM1 << FIR_OP2_SHIFT));
+ (FIR_OP_CM2 << FIR_OP2_SHIFT) |
+ (FIR_OP_CW1 << FIR_OP3_SHIFT) |
+ (FIR_OP_RS << FIR_OP4_SHIFT));
out_be32(&lbc->fcr,
(NAND_CMD_ERASE1 << FCR_CMD0_SHIFT) |
- (NAND_CMD_ERASE2 << FCR_CMD1_SHIFT));
+ (NAND_CMD_STATUS << FCR_CMD1_SHIFT) |
+ (NAND_CMD_ERASE2 << FCR_CMD2_SHIFT));
out_be32(&lbc->fbcr, 0);
ctrl->read_bytes = 0;
+ ctrl->use_mdr = 1;
fsl_elbc_run_command(mtd);
return;
ctrl->column = column;
ctrl->oob = 0;
+ ctrl->use_mdr = 1;
- if (priv->page_size) {
- fcr = (NAND_CMD_SEQIN << FCR_CMD0_SHIFT) |
- (NAND_CMD_PAGEPROG << FCR_CMD1_SHIFT);
+ fcr = (NAND_CMD_STATUS << FCR_CMD1_SHIFT) |
+ (NAND_CMD_SEQIN << FCR_CMD2_SHIFT) |
+ (NAND_CMD_PAGEPROG << FCR_CMD3_SHIFT);
+ if (priv->page_size) {
out_be32(&lbc->fir,
- (FIR_OP_CW0 << FIR_OP0_SHIFT) |
+ (FIR_OP_CM2 << FIR_OP0_SHIFT) |
(FIR_OP_CA << FIR_OP1_SHIFT) |
(FIR_OP_PA << FIR_OP2_SHIFT) |
(FIR_OP_WB << FIR_OP3_SHIFT) |
- (FIR_OP_CW1 << FIR_OP4_SHIFT));
+ (FIR_OP_CM3 << FIR_OP4_SHIFT) |
+ (FIR_OP_CW1 << FIR_OP5_SHIFT) |
+ (FIR_OP_RS << FIR_OP6_SHIFT));
} else {
- fcr = (NAND_CMD_PAGEPROG << FCR_CMD1_SHIFT) |
- (NAND_CMD_SEQIN << FCR_CMD2_SHIFT);
-
out_be32(&lbc->fir,
- (FIR_OP_CW0 << FIR_OP0_SHIFT) |
+ (FIR_OP_CM0 << FIR_OP0_SHIFT) |
(FIR_OP_CM2 << FIR_OP1_SHIFT) |
(FIR_OP_CA << FIR_OP2_SHIFT) |
(FIR_OP_PA << FIR_OP3_SHIFT) |
(FIR_OP_WB << FIR_OP4_SHIFT) |
- (FIR_OP_CW1 << FIR_OP5_SHIFT));
+ (FIR_OP_CM3 << FIR_OP5_SHIFT) |
+ (FIR_OP_CW1 << FIR_OP6_SHIFT) |
+ (FIR_OP_RS << FIR_OP7_SHIFT));
if (column >= mtd->writesize) {
/* OOB area --> READOOB */
column -= mtd->writesize;
fcr |= NAND_CMD_READOOB << FCR_CMD0_SHIFT;
ctrl->oob = 1;
- } else if (column < 256) {
+ } else {
+ WARN_ON(column != 0);
/* First 256 bytes --> READ0 */
fcr |= NAND_CMD_READ0 << FCR_CMD0_SHIFT;
- } else {
- /* Second 256 bytes --> READ1 */
- fcr |= NAND_CMD_READ1 << FCR_CMD0_SHIFT;
}
}
{
struct fsl_elbc_mtd *priv = chip->priv;
struct fsl_elbc_ctrl *ctrl = priv->ctrl;
- struct fsl_lbc_regs __iomem *lbc = ctrl->regs;
-
- if (ctrl->status != LTESR_CC)
- return NAND_STATUS_FAIL;
-
- /* Use READ_STATUS command, but wait for the device to be ready */
- ctrl->use_mdr = 0;
- out_be32(&lbc->fir,
- (FIR_OP_CW0 << FIR_OP0_SHIFT) |
- (FIR_OP_RBW << FIR_OP1_SHIFT));
- out_be32(&lbc->fcr, NAND_CMD_STATUS << FCR_CMD0_SHIFT);
- out_be32(&lbc->fbcr, 1);
- set_addr(mtd, 0, 0, 0);
- ctrl->read_bytes = 1;
-
- fsl_elbc_run_command(mtd);
if (ctrl->status != LTESR_CC)
return NAND_STATUS_FAIL;
/* The chip always seems to report that it is
* write-protected, even when it is not.
*/
- setbits8(ctrl->addr, NAND_STATUS_WP);
- return fsl_elbc_read_byte(mtd);
+ return (ctrl->mdr & 0xff) | NAND_STATUS_WP;
}
static int fsl_elbc_chip_init_tail(struct mtd_info *mtd)
dev_dbg(ctrl->dev, "fsl_elbc_init: nand->numchips = %d\n",
chip->numchips);
- dev_dbg(ctrl->dev, "fsl_elbc_init: nand->chipsize = %ld\n",
+ dev_dbg(ctrl->dev, "fsl_elbc_init: nand->chipsize = %lld\n",
chip->chipsize);
dev_dbg(ctrl->dev, "fsl_elbc_init: nand->pagemask = %8x\n",
chip->pagemask);
dev_dbg(ctrl->dev, "fsl_elbc_init: nand->ecc.layout = %p\n",
chip->ecc.layout);
dev_dbg(ctrl->dev, "fsl_elbc_init: mtd->flags = %08x\n", mtd->flags);
- dev_dbg(ctrl->dev, "fsl_elbc_init: mtd->size = %d\n", mtd->size);
+ dev_dbg(ctrl->dev, "fsl_elbc_init: mtd->size = %lld\n", mtd->size);
dev_dbg(ctrl->dev, "fsl_elbc_init: mtd->erasesize = %d\n",
mtd->erasesize);
dev_dbg(ctrl->dev, "fsl_elbc_init: mtd->writesize = %d\n",
chip->ecc.layout = (priv->fmr & FMR_ECCM) ?
&fsl_elbc_oob_lp_eccm1 :
&fsl_elbc_oob_lp_eccm0;
- mtd->ecclayout = chip->ecc.layout;
- mtd->oobavail = chip->ecc.layout->oobavail;
+ chip->badblock_pattern = &largepage_memorybased;
}
} else {
dev_err(ctrl->dev,
static int fsl_elbc_read_page(struct mtd_info *mtd,
struct nand_chip *chip,
- uint8_t *buf)
+ uint8_t *buf,
+ int page)
{
fsl_elbc_read_buf(mtd, buf, mtd->writesize);
fsl_elbc_read_buf(mtd, chip->oob_poi, mtd->oobsize);
/* Fill in fsl_elbc_mtd structure */
priv->mtd.priv = chip;
priv->mtd.owner = THIS_MODULE;
- priv->fmr = 0; /* rest filled in later */
+
+ /* Set the ECCM according to the settings in bootloader.*/
+ priv->fmr = in_be32(&lbc->fmr) & FMR_ECCM;
/* fill in nand_chip structure */
/* set up function call table */
chip->cmdfunc = fsl_elbc_cmdfunc;
chip->waitfunc = fsl_elbc_wait;
+ chip->bbt_td = &bbt_main_descr;
+ chip->bbt_md = &bbt_mirror_descr;
+
/* set up nand options */
- chip->options = NAND_NO_READRDY | NAND_NO_AUTOINCR;
+ chip->options = NAND_NO_READRDY | NAND_NO_AUTOINCR |
+ NAND_USE_FLASH_BBT;
chip->controller = &ctrl->controller;
chip->priv = priv;
return 0;
}
-static int fsl_elbc_chip_probe(struct fsl_elbc_ctrl *ctrl,
- struct device_node *node)
+static int __devinit fsl_elbc_chip_probe(struct fsl_elbc_ctrl *ctrl,
+ struct device_node *node)
{
struct fsl_lbc_regs __iomem *lbc = ctrl->regs;
struct fsl_elbc_mtd *priv;
goto err;
}
- priv->mtd.name = kasprintf(GFP_KERNEL, "%x.flash", res.start);
+ priv->mtd.name = kasprintf(GFP_KERNEL, "%x.flash", (unsigned)res.start);
if (!priv->mtd.name) {
ret = -ENOMEM;
goto err;
#ifdef CONFIG_MTD_OF_PARTS
if (ret == 0) {
- ret = of_mtd_parse_partitions(priv->dev, &priv->mtd,
- node, &parts);
+ ret = of_mtd_parse_partitions(priv->dev, node, &parts);
if (ret < 0)
goto err;
}
#endif
add_mtd_device(&priv->mtd);
- printk(KERN_INFO "eLBC NAND device at 0x%zx, bank %d\n",
- res.start, priv->bank);
+ printk(KERN_INFO "eLBC NAND device at 0x%llx, bank %d\n",
+ (unsigned long long)res.start, priv->bank);
return 0;
err:
{
struct fsl_lbc_regs __iomem *lbc = ctrl->regs;
+ /*
+ * NAND transactions can tie up the bus for a long time, so set the
+ * bus timeout to max by clearing LBCR[BMT] (highest base counter
+ * value) and setting LBCR[BMTPS] to the highest prescaler value.
+ */
+ clrsetbits_be32(&lbc->lbcr, LBCR_BMT, 15);
+
/* clear event registers */
setbits32(&lbc->ltesr, LTESR_NAND_MASK);
out_be32(&lbc->lteatr, 0);
return 0;
}
-static int __devexit fsl_elbc_ctrl_remove(struct of_device *ofdev)
+static int fsl_elbc_ctrl_remove(struct of_device *ofdev)
{
struct fsl_elbc_ctrl *ctrl = dev_get_drvdata(&ofdev->dev);
int i;
init_waitqueue_head(&ctrl->controller.wq);
init_waitqueue_head(&ctrl->irq_wait);
- ctrl->regs = of_iomap(ofdev->node, 0);
+ ctrl->regs = of_iomap(ofdev->dev.of_node, 0);
if (!ctrl->regs) {
dev_err(&ofdev->dev, "failed to get memory region\n");
ret = -ENODEV;
goto err;
}
- ctrl->irq = of_irq_to_resource(ofdev->node, 0, NULL);
+ ctrl->irq = of_irq_to_resource(ofdev->dev.of_node, 0, NULL);
if (ctrl->irq == NO_IRQ) {
dev_err(&ofdev->dev, "failed to get irq resource\n");
ret = -ENODEV;
goto err;
}
- for_each_child_of_node(ofdev->node, child)
+ for_each_child_of_node(ofdev->dev.of_node, child)
if (of_device_is_compatible(child, "fsl,elbc-fcm-nand"))
fsl_elbc_chip_probe(ctrl, child);
},
.match_table = fsl_elbc_match,
.probe = fsl_elbc_ctrl_probe,
- .remove = __devexit_p(fsl_elbc_ctrl_remove),
+ .remove = fsl_elbc_ctrl_remove,
};
static int __init fsl_elbc_init(void)
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff