-# drivers/mtd/nand/Kconfig
-
menuconfig MTD_NAND
tristate "NAND Device Support"
depends on MTD
help
Support for NAND flash on Amstrad E3 (Delta).
+config MTD_NAND_OMAP2
+ tristate "NAND Flash device on OMAP2 and OMAP3"
+ depends on ARM && MTD_NAND && (ARCH_OMAP2 || ARCH_OMAP3)
+ help
+ Support for NAND flash on Texas Instruments OMAP2 and OMAP3 platforms.
+
+config MTD_NAND_OMAP_PREFETCH
+ bool "GPMC prefetch support for NAND Flash device"
+ depends on MTD_NAND && MTD_NAND_OMAP2
+ default y
+ help
+ The NAND device can be accessed for Read/Write using GPMC PREFETCH engine
+ to improve the performance.
+
+config MTD_NAND_OMAP_PREFETCH_DMA
+ depends on MTD_NAND_OMAP_PREFETCH
+ bool "DMA mode"
+ default n
+ help
+ The GPMC PREFETCH engine can be configured eigther in MPU interrupt mode
+ or in DMA interrupt mode.
+ Say y for DMA mode or MPU mode will be used
+
config MTD_NAND_TS7250
tristate "NAND Flash device on TS-7250 board"
depends on MACH_TS72XX
This enables the NAND flash driver on the PPChameleon EVB Board.
config MTD_NAND_S3C2410
- tristate "NAND Flash support for S3C2410/S3C2440 SoC"
- depends on ARCH_S3C2410
+ tristate "NAND Flash support for Samsung S3C SoCs"
+ depends on ARCH_S3C2410 || ARCH_S3C64XX
help
- This enables the NAND flash controller on the S3C2410 and S3C2440
+ This enables the NAND flash controller on the S3C24xx and S3C64xx
SoCs
No board specific support is done by this driver, each board
must advertise a platform_device for the driver to attach.
config MTD_NAND_S3C2410_DEBUG
- bool "S3C2410 NAND driver debug"
+ bool "Samsung S3C NAND driver debug"
depends on MTD_NAND_S3C2410
help
- Enable debugging of the S3C2410 NAND driver
+ Enable debugging of the S3C NAND driver
config MTD_NAND_S3C2410_HWECC
- bool "S3C2410 NAND Hardware ECC"
+ bool "Samsung S3C NAND Hardware ECC"
depends on MTD_NAND_S3C2410
help
- Enable the use of the S3C2410's internal ECC generator when
- using NAND. Early versions of the chip have had problems with
+ Enable the use of the controller's internal ECC generator when
+ using NAND. Early versions of the chips have had problems with
incorrect ECC generation, and if using these, the default of
software ECC is preferable.
NDFC Nand Flash Controllers are integrated in IBM/AMCC's 4xx SoCs
config MTD_NAND_S3C2410_CLKSTOP
- bool "S3C2410 NAND IDLE clock stop"
+ bool "Samsung S3C NAND IDLE clock stop"
depends on MTD_NAND_S3C2410
default n
help
when the is NAND chip selected or released, but will save
approximately 5mA of power when there is nothing happening.
+config MTD_NAND_BCM_UMI
+ tristate "NAND Flash support for BCM Reference Boards"
+ depends on ARCH_BCMRING && MTD_NAND
+ help
+ This enables the NAND flash controller on the BCM UMI block.
+
+ No board specfic support is done by this driver, each board
+ must advertise a platform_device for the driver to attach.
+
+config MTD_NAND_BCM_UMI_HWCS
+ bool "BCM UMI NAND Hardware CS"
+ depends on MTD_NAND_BCM_UMI
+ help
+ Enable the use of the BCM UMI block's internal CS using NAND.
+ This should only be used if you know the external NAND CS can toggle.
+
config MTD_NAND_DISKONCHIP
tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation) (EXPERIMENTAL)"
depends on EXPERIMENTAL
tristate "Support for NAND Flash on Sharp SL Series (C7xx + others)"
depends on ARCH_PXA
-config MTD_NAND_BASLER_EXCITE
- tristate "Support for NAND Flash on Basler eXcite"
- depends on BASLER_EXCITE
- help
- This enables the driver for the NAND flash device found on the
- Basler eXcite Smart Camera. If built as a module, the driver
- will be named excite_nandflash.
-
config MTD_NAND_CAFE
tristate "NAND support for OLPC CAFÉ chip"
depends on PCI
config MTD_NAND_PXA3xx
tristate "Support for NAND flash devices on PXA3xx"
- depends on MTD_NAND && PXA3xx
+ depends on MTD_NAND && (PXA3xx || ARCH_MMP)
help
This enables the driver for the NAND flash device found on
PXA3xx processors
This enables the driver for the NAND flash controller on the
MXC processors.
+config MTD_NAND_NOMADIK
+ tristate "ST Nomadik 8815 NAND support"
+ depends on ARCH_NOMADIK
+ help
+ Driver for the NAND flash controller on the Nomadik, with ECC.
+
config MTD_NAND_SH_FLCTL
tristate "Support for NAND on Renesas SuperH FLCTL"
- depends on MTD_NAND && SUPERH && CPU_SUBTYPE_SH7723
+ depends on MTD_NAND && SUPERH
help
Several Renesas SuperH CPU has FLCTL. This option enables support
- for NAND Flash using FLCTL. This driver support SH7723.
+ for NAND Flash using FLCTL.
config MTD_NAND_DAVINCI
tristate "Support NAND on DaVinci SoC"
help
Enables support for NAND Flash chips wired onto Socrates board.
+config MTD_NAND_W90P910
+ tristate "Support for NAND on w90p910 evaluation board."
+ depends on ARCH_W90X900 && MTD_PARTITIONS
+ help
+ This enables the driver for the NAND Flash on evaluation board based
+ on w90p910.
+
endif # MTD_NAND
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff