# drivers/mtd/maps/Kconfig
-# $Id: Kconfig,v 1.61 2005/11/07 11:14:26 gleixner Exp $
menu "Mapping drivers for chip access"
depends on MTD!=n
paged mappings of flash chips.
config MTD_PHYSMAP
- tristate "CFI Flash device in physical memory map"
- depends on MTD_CFI || MTD_JEDECPROBE || MTD_ROM
+ tristate "Flash device in physical memory map"
+ depends on MTD_CFI || MTD_JEDECPROBE || MTD_ROM || MTD_LPDDR
help
This provides a 'mapping' driver which allows the NOR Flash and
ROM driver code to communicate with chips which are mapped
particular board as well as the bus width, either statically
with config options or at run-time.
+ To compile this driver as a module, choose M here: the
+ module will be called physmap.
+
+config MTD_PHYSMAP_COMPAT
+ bool "Physmap compat support"
+ depends on MTD_PHYSMAP
+ default n
+ help
+ Setup a simple mapping via the Kconfig options. Normally the
+ physmap configuration options are done via your board's
+ resource file.
+
+ If unsure, say N here.
+
config MTD_PHYSMAP_START
hex "Physical start address of flash mapping"
- depends on MTD_PHYSMAP
+ depends on MTD_PHYSMAP_COMPAT
default "0x8000000"
help
This is the physical memory location at which the flash chips
config MTD_PHYSMAP_LEN
hex "Physical length of flash mapping"
- depends on MTD_PHYSMAP
+ depends on MTD_PHYSMAP_COMPAT
default "0"
help
This is the total length of the mapping of the flash chips on
config MTD_PHYSMAP_BANKWIDTH
int "Bank width in octets"
- depends on MTD_PHYSMAP
+ depends on MTD_PHYSMAP_COMPAT
default "2"
help
This is the total width of the data bus of the flash devices
config MTD_PHYSMAP_OF
tristate "Flash device in physical memory map based on OF description"
- depends on PPC_OF && (MTD_CFI || MTD_JEDECPROBE || MTD_ROM)
+ depends on (MICROBLAZE || PPC_OF) && (MTD_CFI || MTD_JEDECPROBE || MTD_ROM)
help
This provides a 'mapping' driver which allows the NOR Flash and
ROM driver code to communicate with chips which are mapped
default "0x02000000"
depends on MSP_FLASH_MAP_LIMIT_32M
-config MTD_PMC_MSP_RAMROOT
- tristate "Embedded RAM block device for root on PMC-Sierra MSP"
- depends on PMC_MSP_EMBEDDED_ROOTFS && \
- (MTD_BLOCK || MTD_BLOCK_RO) && \
- MTD_RAM
- help
- This provides support for the embedded root file system
- on PMC MSP devices. This memory is mapped as a MTD block device.
-
config MTD_SUN_UFLASH
tristate "Sun Microsystems userflash support"
depends on SPARC && MTD_CFI && PCI
Sun Microsystems boardsets. This driver will require CFI support
in the kernel, so if you did not enable CFI previously, do that now.
-config MTD_PNC2000
- tristate "CFI Flash device mapped on Photron PNC-2000"
- depends on X86 && MTD_CFI && MTD_PARTITIONS
- help
- PNC-2000 is the name of Network Camera product from PHOTRON
- Ltd. in Japan. It uses CFI-compliant flash.
-
config MTD_SC520CDP
tristate "CFI Flash device mapped on AMD SC520 CDP"
depends on X86 && MTD_CFI && MTD_CONCAT
help
Flash memory access on AMD Alchemy Pb/Db/RDK Reference Boards
-config MTD_MTX1
- tristate "4G Systems MTX-1 Flash device"
- depends on MIPS_MTX1 && MTD_CFI
- help
- Flash memory access on 4G Systems MTX-1 Board. If you have one of
- these boards and would like to use the flash chips on it, say 'Y'.
-
config MTD_DILNETPC
tristate "CFI Flash device mapped on DIL/Net PC"
- depends on X86 && MTD_CONCAT && MTD_PARTITIONS && MTD_CFI_INTELEXT
+ depends on X86 && MTD_CONCAT && MTD_PARTITIONS && MTD_CFI_INTELEXT && BROKEN
help
MTD map driver for SSV DIL/Net PC Boards "DNP" and "ADNP".
For details, see <http://www.ssv-embedded.de/ssv/pc104/p169.htm>
BE VERY CAREFUL.
-config MTD_SBC8240
- tristate "Flash device on SBC8240"
- depends on MTD_JEDECPROBE && 8260
- help
- Flash access on the SBC8240 board from Wind River. See
- <http://www.windriver.com/products/sbc8240/>
-
config MTD_TQM8XXL
tristate "CFI Flash device mapped on TQM8XXL"
depends on MTD_CFI && TQM8xxL
Mapping for the Flaga digital module. If you don't have one, ignore
this setting.
-config MTD_WALNUT
- tristate "Flash device mapped on IBM 405GP Walnut"
- depends on MTD_JEDECPROBE && WALNUT && !PPC_MERGE
- help
- This enables access routines for the flash chips on the IBM 405GP
- Walnut board. If you have one of these boards and would like to
- use the flash chips on it, say 'Y'.
-
-config MTD_EBONY
- tristate "Flash devices mapped on IBM 440GP Ebony"
- depends on MTD_JEDECPROBE && EBONY && !PPC_MERGE
- help
- This enables access routines for the flash chips on the IBM 440GP
- Ebony board. If you have one of these boards and would like to
- use the flash chips on it, say 'Y'.
-
-config MTD_OCOTEA
- tristate "Flash devices mapped on IBM 440GX Ocotea"
- depends on MTD_CFI && OCOTEA && !PPC_MERGE
- help
- This enables access routines for the flash chips on the IBM 440GX
- Ocotea board. If you have one of these boards and would like to
- use the flash chips on it, say 'Y'.
-
config MTD_REDWOOD
tristate "CFI Flash devices mapped on IBM Redwood"
depends on MTD_CFI && ( REDWOOD_4 || REDWOOD_5 || REDWOOD_6 )
config MTD_SOLUTIONENGINE
tristate "CFI Flash device mapped on Hitachi SolutionEngine"
- depends on SUPERH && MTD_CFI && MTD_REDBOOT_PARTS
+ depends on SUPERH && SOLUTION_ENGINE && MTD_CFI && MTD_REDBOOT_PARTS
help
This enables access to the flash chips on the Hitachi SolutionEngine and
similar boards. Say 'Y' if you are building a kernel for such a board.
PhotoMax Digital Picture Frame.
If you have such a device, say 'Y'.
-config MTD_NOR_TOTO
- tristate "NOR Flash device on TOTO board"
- depends on ARCH_OMAP && OMAP_TOTO
- help
- This enables access to the NOR flash on the Texas Instruments
- TOTO board.
-
config MTD_H720X
tristate "Hynix evaluation board mappings"
depends on MTD_CFI && ( ARCH_H7201 || ARCH_H7202 )
This enables access to the flash chips on the Hynix evaluation boards.
If you have such a board, say 'Y'.
-config MTD_MPC1211
- tristate "CFI Flash device mapped on Interface MPC-1211"
- depends on SH_MPC1211 && MTD_CFI
- help
- This enables access to the flash chips on the Interface MPC-1211(CTP/PCI/MPC-SH02).
- If you have such a board, say 'Y'.
-
config MTD_OMAP_NOR
tristate "TI OMAP board mappings"
depends on MTD_CFI && ARCH_OMAP
If unsure, say N.
+config MTD_BFIN_ASYNC
+ tristate "Blackfin BF533-STAMP Flash Chip Support"
+ depends on BFIN533_STAMP && MTD_CFI && MTD_COMPLEX_MAPPINGS
+ select MTD_PARTITIONS
+ default y
+ help
+ Map driver which allows for simultaneous utilization of
+ ethernet and CFI parallel flash.
+
+ If compiled as a module, it will be called bfin-async-flash.
+
+config MTD_GPIO_ADDR
+ tristate "GPIO-assisted Flash Chip Support"
+ depends on MTD_COMPLEX_MAPPINGS
+ select MTD_PARTITIONS
+ help
+ Map driver which allows flashes to be partially physically addressed
+ and assisted by GPIOs.
+
+ If compiled as a module, it will be called gpio-addr-flash.
+
config MTD_UCLINUX
- tristate "Generic uClinux RAM/ROM filesystem support"
- depends on MTD_PARTITIONS && !MMU
+ bool "Generic uClinux RAM/ROM filesystem support"
+ depends on MTD_PARTITIONS && MTD_RAM=y && !MMU
help
Map driver to support image based filesystems for uClinux.
help
Map driver for Dy-4 SVME/DMV-182 board.
-config MTD_BAST
- tristate "Map driver for Simtec BAST (EB2410ITX) or Thorcom VR1000"
- depends on ARCH_BAST || MACH_VR1000
- select MTD_PARTITIONS
- select MTD_MAP_BANK_WIDTH_16
- select MTD_JEDECPROBE
- help
- Map driver for NOR flash on the Simtec BAST (EB2410ITX), or the
- Thorcom VR1000
-
- Note, this driver *cannot* over-ride the WP link on the
- board, or currently detect the state of the link.
-
-config MTD_BAST_MAXSIZE
- int "Maximum size for BAST flash area (MiB)"
- depends on MTD_BAST
- default "4"
-
-config MTD_SHARP_SL
- tristate "ROM mapped on Sharp SL Series"
- depends on ARCH_PXA
- help
- This enables access to the flash chip on the Sharp SL Series of PDAs.
-
config MTD_INTEL_VR_NOR
tristate "NOR flash on Intel Vermilion Range Expansion Bus CS0"
depends on PCI
Map driver for a NOR flash bank located on the Expansion Bus of the
Intel Vermilion Range chipset.
+config MTD_RBTX4939
+ tristate "Map driver for RBTX4939 board"
+ depends on TOSHIBA_RBTX4939 && MTD_CFI && MTD_COMPLEX_MAPPINGS
+ help
+ Map driver for NOR flash chips on RBTX4939 board.
+
config MTD_PLATRAM
tristate "Map driver for platform device RAM (mtd-ram)"
select MTD_RAM
This selection automatically selects the map_ram driver.
-endmenu
+config MTD_VMU
+ tristate "Map driver for Dreamcast VMU"
+ depends on MAPLE
+ help
+ This driver enables access to the Dreamcast Visual Memory Unit (VMU).
+ Most Dreamcast users will want to say Y here.
+
+ To build this as a module select M here, the module will be called
+ vmu-flash.
+
+endmenu