config ATMEL_PWM
tristate "Atmel AT32/AT91 PWM support"
- depends on AVR32 || ARCH_AT91
+ depends on AVR32 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9
help
This option enables device driver support for the PWM channels
on certain Atmel prcoessors. Pulse Width Modulation is used for
purposes including software controlled power-efficent backlights
on LCD displays, motor control, and waveform generation.
+config ATMEL_TCLIB
+ bool "Atmel AT32/AT91 Timer/Counter Library"
+ depends on (AVR32 || ARCH_AT91)
+ help
+ Select this if you want a library to allocate the Timer/Counter
+ blocks found on many Atmel processors. This facilitates using
+ these blocks by different drivers despite processor differences.
+
+config ATMEL_TCB_CLKSRC
+ bool "TC Block Clocksource"
+ depends on ATMEL_TCLIB && GENERIC_TIME
+ default y
+ help
+ Select this to get a high precision clocksource based on a
+ TC block with a 5+ MHz base clock rate. Two timer channels
+ are combined to make a single 32-bit timer.
+
+ When GENERIC_CLOCKEVENTS is defined, the third timer channel
+ may be used as a clock event device supporting oneshot mode
+ (delays of up to two seconds) based on the 32 KiHz clock.
+
+config ATMEL_TCB_CLKSRC_BLOCK
+ int
+ depends on ATMEL_TCB_CLKSRC
+ prompt "TC Block" if ARCH_AT91RM9200 || ARCH_AT91SAM9260 || CPU_AT32AP700X
+ default 0
+ range 0 1
+ help
+ Some chips provide more than one TC block, so you have the
+ choice of which one to use for the clock framework. The other
+ TC can be used for other purposes, such as PWM generation and
+ interval timing.
+
config IBM_ASM
tristate "Device driver for IBM RSA service processor"
depends on X86 && PCI && INPUT && EXPERIMENTAL
for your IBM server.
config PHANTOM
- tristate "Sensable PHANToM"
+ tristate "Sensable PHANToM (PCI)"
depends on PCI
help
Say Y here if you want to build a driver for Sensable PHANToM device.
+ This driver is only for PCI PHANToMs.
+
If you choose to build module, its name will be phantom. If unsure,
say N here.
depends on EXPERIMENTAL
depends on ACPI
depends on LEDS_CLASS
+ depends on NEW_LEDS
depends on BACKLIGHT_CLASS_DEVICE
+ depends on SERIO_I8042
+ depends on RFKILL
select ACPI_WMI
---help---
This is a driver for newer Acer (and Wistron) laptops. It adds
wireless radio and bluetooth control, and on some laptops,
exposes the mail LED and LCD backlight.
+ For more information about this driver see
+ <file:Documentation/laptops/acer-wmi.txt>
+
If you have an ACPI-WMI compatible Acer/ Wistron laptop, say Y or M
here.
depends on ACPI
depends on EXPERIMENTAL && !ACPI_ASUS
depends on LEDS_CLASS
+ depends on NEW_LEDS
depends on BACKLIGHT_CLASS_DEVICE
---help---
This is the new Linux driver for Asus laptops. It may also support some
tristate "Fujitsu Laptop Extras"
depends on X86
depends on ACPI
+ depends on INPUT
depends on BACKLIGHT_CLASS_DEVICE
---help---
This is a driver for laptops built by Fujitsu:
* P2xxx/P5xxx/S6xxx/S7xxx series Lifebooks
* Possibly other Fujitsu laptop models
+ * Tested with S6410 and S7020
- It adds support for LCD brightness control.
+ It adds support for LCD brightness control and some hotkeys.
If you have a Fujitsu laptop, say Y or M here.
+config FUJITSU_LAPTOP_DEBUG
+ bool "Verbose debug mode for Fujitsu Laptop Extras"
+ depends on FUJITSU_LAPTOP
+ default n
+ ---help---
+ Enables extra debug output from the fujitsu extras driver, at the
+ expense of a slight increase in driver size.
+
+ If you are not sure, say N here.
+
config TC1100_WMI
- tristate "HP Compaq TC1100 Tablet WMI Extras"
+ tristate "HP Compaq TC1100 Tablet WMI Extras (EXPERIMENTAL)"
depends on X86 && !X86_64
+ depends on EXPERIMENTAL
depends on ACPI
select ACPI_WMI
---help---
This is a driver for the WMI extensions (wireless and bluetooth power
control) of the HP Compaq TC1100 tablet.
+config HP_WMI
+ tristate "HP WMI extras"
+ depends on ACPI_WMI
+ depends on INPUT
+ depends on RFKILL
+ help
+ Say Y here if you want to support WMI-based hotkeys on HP laptops and
+ to read data from WMI such as docking or ambient light sensor state.
+
+ To compile this driver as a module, choose M here: the module will
+ be called hp-wmi.
+
+config ICS932S401
+ tristate "Integrated Circuits ICS932S401"
+ depends on I2C && EXPERIMENTAL
+ help
+ If you say yes here you get support for the Integrated Circuits
+ ICS932S401 clock control chips.
+
+ This driver can also be built as a module. If so, the module
+ will be called ics932s401.
+
config MSI_LAPTOP
tristate "MSI Laptop Extras"
depends on X86
- depends on ACPI_EC
+ depends on ACPI
depends on BACKLIGHT_CLASS_DEVICE
---help---
This is a driver for laptops built by MSI (MICRO-STAR
If you have an MSI S270 laptop, say Y or M here.
+config PANASONIC_LAPTOP
+ tristate "Panasonic Laptop Extras"
+ depends on X86 && INPUT && ACPI
+ depends on BACKLIGHT_CLASS_DEVICE
+ ---help---
+ This driver adds support for access to backlight control and hotkeys
+ on Panasonic Let's Note laptops.
+
+ If you have a Panasonic Let's note laptop (such as the R1(N variant),
+ R2, R3, R5, T2, W2 and Y2 series), say Y.
+
+config COMPAL_LAPTOP
+ tristate "Compal Laptop Extras"
+ depends on X86
+ depends on ACPI
+ depends on BACKLIGHT_CLASS_DEVICE
+ ---help---
+ This is a driver for laptops built by Compal:
+
+ Compal FL90/IFL90
+ Compal FL91/IFL91
+ Compal FL92/JFL92
+ Compal FT00/IFT00
+
+ It adds support for Bluetooth, WLAN and LCD brightness control.
+
+ If you have an Compal FL9x/IFL9x/FT00 laptop, say Y or M here.
+
config SONY_LAPTOP
tristate "Sony Laptop Extras"
depends on X86 && ACPI
screen brightness control, Fn keys and allows powering on/off some
devices.
- Read <file:Documentation/sony-laptop.txt> for more information.
+ Read <file:Documentation/laptops/sony-laptop.txt> for more information.
config SONYPI_COMPAT
bool "Sonypi compatibility"
config THINKPAD_ACPI
tristate "ThinkPad ACPI Laptop Extras"
depends on X86 && ACPI
+ select BACKLIGHT_LCD_SUPPORT
select BACKLIGHT_CLASS_DEVICE
select HWMON
select NVRAM
- depends on INPUT
+ select INPUT
+ select NEW_LEDS
+ select LEDS_CLASS
+ select NET
+ select RFKILL
---help---
This is a driver for the IBM and Lenovo ThinkPad laptops. It adds
support for Fn-Fx key combinations, Bluetooth control, video
If you are not sure, say Y here.
+config THINKPAD_ACPI_VIDEO
+ bool "Video output control support"
+ depends on THINKPAD_ACPI
+ default y
+ ---help---
+ Allows the thinkpad_acpi driver to provide an interface to control
+ the various video output ports.
+
+ This feature often won't work well, depending on ThinkPad model,
+ display state, video output devices in use, whether there is a X
+ server running, phase of the moon, and the current mood of
+ Schroedinger's cat. If you can use X.org's RandR to control
+ your ThinkPad's video output ports instead of this feature,
+ don't think twice: do it and say N here to save some memory.
+
+ If you are not sure, say Y here.
+
config THINKPAD_ACPI_HOTKEY_POLL
- bool "Suport NVRAM polling for hot keys"
+ bool "Support NVRAM polling for hot keys"
depends on THINKPAD_ACPI
default y
---help---
config INTEL_MENLOW
tristate "Thermal Management driver for Intel menlow platform"
depends on ACPI_THERMAL
+ select THERMAL
depends on X86
---help---
ACPI thermal management enhancement driver on
If unsure, say N.
+config EEEPC_LAPTOP
+ tristate "Eee PC Hotkey Driver (EXPERIMENTAL)"
+ depends on X86
+ depends on ACPI
+ depends on BACKLIGHT_CLASS_DEVICE
+ depends on HWMON
+ depends on EXPERIMENTAL
+ depends on RFKILL
+ ---help---
+ This driver supports the Fn-Fx keys on Eee PC laptops.
+ It also adds the ability to switch camera/wlan on/off.
+
+ If you have an Eee PC laptop, say Y or M here.
+
config ENCLOSURE_SERVICES
tristate "Enclosure Services"
default n
driver (SCSI/ATA) which supports enclosures
or a SCSI enclosure device (SES) to use these services.
+config SGI_XP
+ tristate "Support communication between SGI SSIs"
+ depends on NET
+ depends on (IA64_GENERIC || IA64_SGI_SN2 || IA64_SGI_UV || X86_64) && SMP
+ select IA64_UNCACHED_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2
+ select GENERIC_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2
+ select SGI_GRU if (IA64_GENERIC || IA64_SGI_UV || X86_64) && SMP
+ ---help---
+ An SGI machine can be divided into multiple Single System
+ Images which act independently of each other and have
+ hardware based memory protection from the others. Enabling
+ this feature will allow for direct communication between SSIs
+ based on a network adapter and DMA messaging.
+
+config HP_ILO
+ tristate "Channel interface driver for HP iLO/iLO2 processor"
+ depends on PCI
+ default n
+ help
+ The channel interface driver allows applications to communicate
+ with iLO/iLO2 management processors present on HP ProLiant
+ servers. Upon loading, the driver creates /dev/hpilo/dXccbN files,
+ which can be used to gather data from the management processor,
+ via read and write system calls.
+
+ To compile this driver as a module, choose M here: the
+ module will be called hpilo.
+
+config SGI_GRU
+ tristate "SGI GRU driver"
+ depends on (X86_64 || IA64_SGI_UV || IA64_GENERIC) && SMP
+ default n
+ select MMU_NOTIFIER
+ ---help---
+ The GRU is a hardware resource located in the system chipset. The GRU
+ contains memory that can be mmapped into the user address space. This memory is
+ used to communicate with the GRU to perform functions such as load/store,
+ scatter/gather, bcopy, AMOs, etc. The GRU is directly accessed by user
+ instructions using user virtual addresses. GRU instructions (ex., bcopy) use
+ user virtual addresses for operands.
+
+ If you are not running on a SGI UV system, say N.
+
+config SGI_GRU_DEBUG
+ bool "SGI GRU driver debug"
+ depends on SGI_GRU
+ default n
+ ---help---
+ This option enables addition debugging code for the SGI GRU driver. If
+ you are unsure, say N.
+
+source "drivers/misc/c2port/Kconfig"
+
endif # MISC_DEVICES