config ATMEL_PWM
tristate "Atmel AT32/AT91 PWM support"
- depends on AVR32 || ARCH_AT91
+ depends on AVR32 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9
help
This option enables device driver support for the PWM channels
on certain Atmel prcoessors. Pulse Width Modulation is used for
purposes including software controlled power-efficent backlights
on LCD displays, motor control, and waveform generation.
+config ATMEL_TCLIB
+ bool "Atmel AT32/AT91 Timer/Counter Library"
+ depends on (AVR32 || ARCH_AT91)
+ help
+ Select this if you want a library to allocate the Timer/Counter
+ blocks found on many Atmel processors. This facilitates using
+ these blocks by different drivers despite processor differences.
+
+config ATMEL_TCB_CLKSRC
+ bool "TC Block Clocksource"
+ depends on ATMEL_TCLIB && GENERIC_TIME
+ default y
+ help
+ Select this to get a high precision clocksource based on a
+ TC block with a 5+ MHz base clock rate. Two timer channels
+ are combined to make a single 32-bit timer.
+
+ When GENERIC_CLOCKEVENTS is defined, the third timer channel
+ may be used as a clock event device supporting oneshot mode
+ (delays of up to two seconds) based on the 32 KiHz clock.
+
+config ATMEL_TCB_CLKSRC_BLOCK
+ int
+ depends on ATMEL_TCB_CLKSRC
+ prompt "TC Block" if ARCH_AT91RM9200 || ARCH_AT91SAM9260 || CPU_AT32AP700X
+ default 0
+ range 0 1
+ help
+ Some chips provide more than one TC block, so you have the
+ choice of which one to use for the clock framework. The other
+ TC can be used for other purposes, such as PWM generation and
+ interval timing.
+
config IBM_ASM
tristate "Device driver for IBM RSA service processor"
depends on X86 && PCI && INPUT && EXPERIMENTAL
for your IBM server.
config PHANTOM
- tristate "Sensable PHANToM"
+ tristate "Sensable PHANToM (PCI)"
depends on PCI
help
Say Y here if you want to build a driver for Sensable PHANToM device.
+ This driver is only for PCI PHANToMs.
+
If you choose to build module, its name will be phantom. If unsure,
say N here.
-config EEPROM_93CX6
- tristate "EEPROM 93CX6 support"
- ---help---
- This is a driver for the EEPROM chipsets 93c46 and 93c66.
- The driver supports both read as well as write commands.
-
- If unsure, say N.
-
config SGI_IOC4
tristate "SGI IOC4 Base IO support"
depends on PCI
cards are supported via 'MMC/SD Card support: TI Flash Media MMC/SD
Interface support (MMC_TIFM_SD)'.
- To compile this driver as a module, choose M here: the module will
+ To compile this driver as a module, choose M here: the module will
be called tifm_core.
config TIFM_7XX1
To make actual use of the device, you will have to select some
flash card format drivers, as outlined in the TIFM_CORE Help.
- To compile this driver as a module, choose M here: the module will
+ To compile this driver as a module, choose M here: the module will
be called tifm_7xx1.
-config ACER_WMI
- tristate "Acer WMI Laptop Extras (EXPERIMENTAL)"
- depends on X86
- depends on EXPERIMENTAL
- depends on ACPI
- depends on LEDS_CLASS
- depends on BACKLIGHT_CLASS_DEVICE
- select ACPI_WMI
- ---help---
- This is a driver for newer Acer (and Wistron) laptops. It adds
- wireless radio and bluetooth control, and on some laptops,
- exposes the mail LED and LCD backlight.
-
- For more information about this driver see
- <file:Documentation/laptops/acer-wmi.txt>
-
- If you have an ACPI-WMI compatible Acer/ Wistron laptop, say Y or M
- here.
-
-config ASUS_LAPTOP
- tristate "Asus Laptop Extras (EXPERIMENTAL)"
- depends on X86
- depends on ACPI
- depends on EXPERIMENTAL && !ACPI_ASUS
- depends on LEDS_CLASS
- depends on BACKLIGHT_CLASS_DEVICE
- ---help---
- This is the new Linux driver for Asus laptops. It may also support some
- MEDION, JVC or VICTOR laptops. It makes all the extra buttons generate
- standard ACPI events that go through /proc/acpi/events. It also adds
- support for video output switching, LCD backlight control, Bluetooth and
- Wlan control, and most importantly, allows you to blink those fancy LEDs.
-
- For more information and a userspace daemon for handling the extra
- buttons see <http://acpi4asus.sf.net/>.
-
- If you have an ACPI-compatible ASUS laptop, say Y or M here.
-
-config FUJITSU_LAPTOP
- tristate "Fujitsu Laptop Extras"
- depends on X86
- depends on ACPI
- depends on BACKLIGHT_CLASS_DEVICE
- ---help---
- This is a driver for laptops built by Fujitsu:
-
- * P2xxx/P5xxx/S6xxx/S7xxx series Lifebooks
- * Possibly other Fujitsu laptop models
-
- It adds support for LCD brightness control.
-
- If you have a Fujitsu laptop, say Y or M here.
-
-config TC1100_WMI
- tristate "HP Compaq TC1100 Tablet WMI Extras (EXPERIMENTAL)"
- depends on X86 && !X86_64
- depends on EXPERIMENTAL
- depends on ACPI
- select ACPI_WMI
- ---help---
- This is a driver for the WMI extensions (wireless and bluetooth power
- control) of the HP Compaq TC1100 tablet.
-
-config MSI_LAPTOP
- tristate "MSI Laptop Extras"
- depends on X86
- depends on ACPI_EC
- depends on BACKLIGHT_CLASS_DEVICE
- ---help---
- This is a driver for laptops built by MSI (MICRO-STAR
- INTERNATIONAL):
-
- MSI MegaBook S270 (MS-1013)
- Cytron/TCM/Medion/Tchibo MD96100/SAM2000
-
- It adds support for Bluetooth, WLAN and LCD brightness control.
-
- More information about this driver is available at
- <http://0pointer.de/lennart/tchibo.html>.
-
- If you have an MSI S270 laptop, say Y or M here.
-
-config SONY_LAPTOP
- tristate "Sony Laptop Extras"
- depends on X86 && ACPI
- select BACKLIGHT_CLASS_DEVICE
- depends on INPUT
- ---help---
- This mini-driver drives the SNC and SPIC devices present in the ACPI
- BIOS of the Sony Vaio laptops.
-
- It gives access to some extra laptop functionalities like Bluetooth,
- screen brightness control, Fn keys and allows powering on/off some
- devices.
-
- Read <file:Documentation/laptops/sony-laptop.txt> for more information.
-
-config SONYPI_COMPAT
- bool "Sonypi compatibility"
- depends on SONY_LAPTOP
- ---help---
- Build the sonypi driver compatibility code into the sony-laptop driver.
-
-config THINKPAD_ACPI
- tristate "ThinkPad ACPI Laptop Extras"
- depends on X86 && ACPI
- select BACKLIGHT_CLASS_DEVICE
- select HWMON
- select NVRAM
- depends on INPUT
- ---help---
- This is a driver for the IBM and Lenovo ThinkPad laptops. It adds
- support for Fn-Fx key combinations, Bluetooth control, video
- output switching, ThinkLight control, UltraBay eject and more.
- For more information about this driver see
- <file:Documentation/laptops/thinkpad-acpi.txt> and
- <http://ibm-acpi.sf.net/> .
-
- This driver was formerly known as ibm-acpi.
-
- If you have an IBM or Lenovo ThinkPad laptop, say Y or M here.
-
-config THINKPAD_ACPI_DEBUG
- bool "Verbose debug mode"
- depends on THINKPAD_ACPI
- default n
- ---help---
- Enables extra debugging information, at the expense of a slightly
- increase in driver size.
-
- If you are not sure, say N here.
-
-config THINKPAD_ACPI_DOCK
- bool "Legacy Docking Station Support"
- depends on THINKPAD_ACPI
- depends on ACPI_DOCK=n
- default n
- ---help---
- Allows the thinkpad_acpi driver to handle docking station events.
- This support was made obsolete by the generic ACPI docking station
- support (CONFIG_ACPI_DOCK). It will allow locking and removing the
- laptop from the docking station, but will not properly connect PCI
- devices.
-
- If you are not sure, say N here.
-
-config THINKPAD_ACPI_BAY
- bool "Legacy Removable Bay Support"
- depends on THINKPAD_ACPI
- default y
- ---help---
- Allows the thinkpad_acpi driver to handle removable bays. It will
- electrically disable the device in the bay, and also generate
- notifications when the bay lever is ejected or inserted.
-
- If you are not sure, say Y here.
-
-config THINKPAD_ACPI_VIDEO
- bool "Video output control support"
- depends on THINKPAD_ACPI
- default y
- ---help---
- Allows the thinkpad_acpi driver to provide an interface to control
- the various video output ports.
-
- This feature often won't work well, depending on ThinkPad model,
- display state, video output devices in use, whether there is a X
- server running, phase of the moon, and the current mood of
- Schroedinger's cat. If you can use X.org's RandR to control
- your ThinkPad's video output ports instead of this feature,
- don't think twice: do it and say N here to save some memory.
-
- If you are not sure, say Y here.
-
-config THINKPAD_ACPI_HOTKEY_POLL
- bool "Suport NVRAM polling for hot keys"
- depends on THINKPAD_ACPI
- default y
- ---help---
- Some thinkpad models benefit from NVRAM polling to detect a few of
- the hot key press events. If you know your ThinkPad model does not
- need to do NVRAM polling to support any of the hot keys you use,
- unselecting this option will save about 1kB of memory.
-
- ThinkPads T40 and newer, R52 and newer, and X31 and newer are
- unlikely to need NVRAM polling in their latest BIOS versions.
-
- NVRAM polling can detect at most the following keys: ThinkPad/Access
- IBM, Zoom, Switch Display (fn+F7), ThinkLight, Volume up/down/mute,
- Brightness up/down, Display Expand (fn+F8), Hibernate (fn+F12).
+config ICS932S401
+ tristate "Integrated Circuits ICS932S401"
+ depends on I2C && EXPERIMENTAL
+ help
+ If you say yes here you get support for the Integrated Circuits
+ ICS932S401 clock control chips.
- If you are not sure, say Y here. The driver enables polling only if
- it is strictly necessary to do so.
+ This driver can also be built as a module. If so, the module
+ will be called ics932s401.
config ATMEL_SSC
tristate "Device driver for Atmel SSC peripheral"
If unsure, say N.
-config INTEL_MENLOW
- tristate "Thermal Management driver for Intel menlow platform"
- depends on ACPI_THERMAL
- depends on X86
- ---help---
- ACPI thermal management enhancement driver on
- Intel Menlow platform.
-
- If unsure, say N.
-
config ENCLOSURE_SERVICES
tristate "Enclosure Services"
default n
driver (SCSI/ATA) which supports enclosures
or a SCSI enclosure device (SES) to use these services.
+config SGI_XP
+ tristate "Support communication between SGI SSIs"
+ depends on NET
+ depends on (IA64_GENERIC || IA64_SGI_SN2 || IA64_SGI_UV || X86_UV) && SMP
+ select IA64_UNCACHED_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2
+ select GENERIC_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2
+ select SGI_GRU if (IA64_GENERIC || IA64_SGI_UV || X86_64) && SMP
+ ---help---
+ An SGI machine can be divided into multiple Single System
+ Images which act independently of each other and have
+ hardware based memory protection from the others. Enabling
+ this feature will allow for direct communication between SSIs
+ based on a network adapter and DMA messaging.
+
+config HP_ILO
+ tristate "Channel interface driver for HP iLO/iLO2 processor"
+ depends on PCI
+ default n
+ help
+ The channel interface driver allows applications to communicate
+ with iLO/iLO2 management processors present on HP ProLiant
+ servers. Upon loading, the driver creates /dev/hpilo/dXccbN files,
+ which can be used to gather data from the management processor,
+ via read and write system calls.
+
+ To compile this driver as a module, choose M here: the
+ module will be called hpilo.
+
+config SGI_GRU
+ tristate "SGI GRU driver"
+ depends on (X86_UV || IA64_SGI_UV || IA64_GENERIC) && SMP
+ default n
+ select MMU_NOTIFIER
+ ---help---
+ The GRU is a hardware resource located in the system chipset. The GRU
+ contains memory that can be mmapped into the user address space. This memory is
+ used to communicate with the GRU to perform functions such as load/store,
+ scatter/gather, bcopy, AMOs, etc. The GRU is directly accessed by user
+ instructions using user virtual addresses. GRU instructions (ex., bcopy) use
+ user virtual addresses for operands.
+
+ If you are not running on a SGI UV system, say N.
+
+config SGI_GRU_DEBUG
+ bool "SGI GRU driver debug"
+ depends on SGI_GRU
+ default n
+ ---help---
+ This option enables addition debugging code for the SGI GRU driver. If
+ you are unsure, say N.
+
+config DELL_LAPTOP
+ tristate "Dell Laptop Extras (EXPERIMENTAL)"
+ depends on X86
+ depends on DCDBAS
+ depends on EXPERIMENTAL
+ depends on BACKLIGHT_CLASS_DEVICE
+ depends on RFKILL
+ depends on POWER_SUPPLY
+ default n
+ ---help---
+ This driver adds support for rfkill and backlight control to Dell
+ laptops.
+
+source "drivers/misc/c2port/Kconfig"
+source "drivers/misc/eeprom/Kconfig"
+
endif # MISC_DEVICES