This option enables support for the LEDs on Sharp Locomo.
Zaurus models SL-5500 and SL-5600.
+config LEDS_MIKROTIK_RB532
+ tristate "LED Support for Mikrotik Routerboard 532"
+ depends on LEDS_CLASS && MIKROTIK_RB532
+ help
+ This option enables support for the so called "User LED" of
+ Mikrotik's Routerboard 532.
+
config LEDS_S3C24XX
tristate "LED Support for Samsung S3C24XX GPIO LEDs"
depends on LEDS_CLASS && ARCH_S3C2410
depends on LEDS_CLASS && X86 && EXPERIMENTAL
help
This option enables support for the PCEngines ALIX.2 and ALIX.3 LEDs.
+ You have to set leds-alix2.force=1 for boards with Award BIOS.
config LEDS_H1940
tristate "LED Support for iPAQ H1940 device"
of_platform devices. For instance, LEDs which are listed in a "dts"
file.
+config LEDS_LP3944
+ tristate "LED Support for N.S. LP3944 (Fun Light) I2C chip"
+ depends on LEDS_CLASS && I2C
+ help
+ This option enables support for LEDs connected to the National
+ Semiconductor LP3944 Lighting Management Unit (LMU) also known as
+ Fun Light Chip.
+
+ To compile this driver as a module, choose M here: the
+ module will be called leds-lp3944.
+
config LEDS_CLEVO_MAIL
- tristate "Mail LED on Clevo notebook (EXPERIMENTAL)"
- depends on LEDS_CLASS && X86 && SERIO_I8042 && DMI && EXPERIMENTAL
+ tristate "Mail LED on Clevo notebook"
+ depends on LEDS_CLASS && X86 && SERIO_I8042 && DMI
help
This driver makes the mail LED accessible from userspace
programs through the leds subsystem. This LED have three
LED driver chips accessed via the I2C bus. Supported
devices include PCA9550, PCA9551, PCA9552, and PCA9553.
+config LEDS_WM831X_STATUS
+ tristate "LED support for status LEDs on WM831x PMICs"
+ depends on LEDS_CLASS && MFD_WM831X
+ help
+ This option enables support for the status LEDs of the WM831x
+ series of PMICs.
+
config LEDS_WM8350
tristate "LED Support for WM8350 AudioPlus PMIC"
depends on LEDS_CLASS && MFD_WM8350
This option enables support for DAC124S085 SPI DAC from NatSemi,
which can be used to control up to four LEDs.
+config LEDS_PWM
+ tristate "PWM driven LED Support"
+ depends on LEDS_CLASS && HAVE_PWM
+ help
+ This option enables support for pwm driven LEDs
+
+config LEDS_REGULATOR
+ tristate "REGULATOR driven LED support"
+ depends on LEDS_CLASS && REGULATOR
+ help
+ This option enables support for regulator driven LEDs.
+
+config LEDS_BD2802
+ tristate "LED driver for BD2802 RGB LED"
+ depends on LEDS_CLASS && I2C
+ help
+ This option enables support for BD2802GU RGB LED driver chips
+ accessed via the I2C bus.
+
+config LEDS_INTEL_SS4200
+ tristate "LED driver for Intel NAS SS4200 series"
+ depends on LEDS_CLASS && PCI && DMI
+ help
+ This option enables support for the Intel SS4200 series of
+ Network Attached Storage servers. You may control the hard
+ drive or power LEDs on the front panel. Using this driver
+ can stop the front LED from blinking after startup.
+
+config LEDS_LT3593
+ tristate "LED driver for LT3593 controllers"
+ depends on LEDS_CLASS && GENERIC_GPIO
+ help
+ This option enables support for LEDs driven by a Linear Technology
+ LT3593 controller. This controller uses a special one-wire pulse
+ coding protocol to set the brightness.
+
+config LEDS_ADP5520
+ tristate "LED Support for ADP5520/ADP5501 PMIC"
+ depends on LEDS_CLASS && PMIC_ADP5520
+ help
+ This option enables support for on-chip LED drivers found
+ on Analog Devices ADP5520/ADP5501 PMICs.
+
+ To compile this driver as a module, choose M here: the module will
+ be called leds-adp5520.
+
comment "LED Triggers"
config LEDS_TRIGGERS
If unsure, say N.
+config LEDS_TRIGGER_GPIO
+ tristate "LED GPIO Trigger"
+ depends on LEDS_TRIGGERS
+ depends on GPIOLIB
+ help
+ This allows LEDs to be controlled by gpio events. It's good
+ when using gpios as switches and triggering the needed LEDs
+ from there. One use case is n810's keypad LEDs that could
+ be triggered by this trigger when user slides up to show
+ keypad.
+
+ If unsure, say N.
+
config LEDS_TRIGGER_DEFAULT_ON
tristate "LED Default ON Trigger"
depends on LEDS_TRIGGERS