#
-# Mouse driver configuration
+# Touchscreen driver configuration
#
menuconfig INPUT_TOUCHSCREEN
bool "Touchscreens"
if INPUT_TOUCHSCREEN
config TOUCHSCREEN_ADS7846
- tristate "ADS 7846 based touchscreens"
+ tristate "ADS7846/TSC2046 and ADS7843 based touchscreens"
depends on SPI_MASTER
+ depends on HWMON = n || HWMON
help
Say Y here if you have a touchscreen interface using the
- ADS7846 controller, and your board-specific initialization
- code includes that in its table of SPI devices.
+ ADS7846/TSC2046 or ADS7843 controller, and your board-specific
+ setup code includes that in its table of SPI devices.
+
+ If HWMON is selected, and the driver is told the reference voltage
+ on your board, you will also get hwmon interfaces for the voltage
+ (and on ads7846/tsc2046, temperature) sensors of this chip.
If unsure, say N (but it's safe to say "Y").
config TOUCHSCREEN_CORGI
tristate "SharpSL (Corgi and Spitz series) touchscreen driver"
depends on PXA_SHARPSL
- default y
+ default y
help
- Say Y here to enable the driver for the touchscreen on the
+ Say Y here to enable the driver for the touchscreen on the
Sharp SL-C7xx and SL-Cxx00 series of PDAs.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called corgi_ts.
+config TOUCHSCREEN_FUJITSU
+ tristate "Fujitsu serial touchscreen"
+ select SERIO
+ help
+ Say Y here if you have the Fujitsu touchscreen (such as one
+ installed in Lifebook P series laptop) connected to your
+ system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called fujitsu-ts.
+
config TOUCHSCREEN_GUNZE
tristate "Gunze AHL-51S touchscreen"
select SERIO
To compile this driver as a module, choose M here: the
module will be called mtouch.
+config TOUCHSCREEN_INEXIO
+ tristate "iNexio serial touchscreens"
+ select SERIO
+ help
+ Say Y here if you have an iNexio serial touchscreen connected to
+ your system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called inexio.
+
config TOUCHSCREEN_MK712
tristate "ICS MicroClock MK712 touchscreen"
help
module will be called mk712.
config TOUCHSCREEN_HP600
- tristate "HP Jornada 680/690 touchscreen"
+ tristate "HP Jornada 6xx touchscreen"
depends on SH_HP6XX && SH_ADC
help
- Say Y here if you have a HP Jornada 680 or 690 and want to
+ Say Y here if you have a HP Jornada 620/660/680/690 and want to
support the built-in touchscreen.
+ To compile this driver as a module, choose M here: the
+ module will be called hp680_ts_input.
+
+config TOUCHSCREEN_HP7XX
+ tristate "HP Jornada 7xx touchscreen"
+ depends on SA1100_JORNADA720_SSP
+ help
+ Say Y here if you have a HP Jornada 710/720/728 and want
+ to support the built-in touchscreen.
+
+ To compile this driver as a module, choose M here: the
+ module will be called jornada720_ts.
+
+config TOUCHSCREEN_HTCPEN
+ tristate "HTC Shift X9500 touchscreen"
+ depends on ISA
+ help
+ Say Y here if you have an HTC Shift UMPC also known as HTC X9500
+ Clio / Shangrila and want to support the built-in touchscreen.
+
If unsure, say N.
To compile this driver as a module, choose M here: the
- module will be called hp680_ts_input.
+ module will be called htcpen.
config TOUCHSCREEN_PENMOUNT
tristate "Penmount serial touchscreen"
To compile this driver as a module, choose M here: the
module will be called penmount.
+config TOUCHSCREEN_MIGOR
+ tristate "Renesas MIGO-R touchscreen"
+ depends on SH_MIGOR && I2C
+ help
+ Say Y here to enable MIGO-R touchscreen support.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called migor_ts.
+
+config TOUCHSCREEN_TOUCHRIGHT
+ tristate "Touchright serial touchscreen"
+ select SERIO
+ help
+ Say Y here if you have a Touchright serial touchscreen connected to
+ your system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called touchright.
+
+config TOUCHSCREEN_TOUCHWIN
+ tristate "Touchwin serial touchscreen"
+ select SERIO
+ help
+ Say Y here if you have a Touchwin serial touchscreen connected to
+ your system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called touchwin.
+
+config TOUCHSCREEN_ATMEL_TSADCC
+ tristate "Atmel Touchscreen Interface"
+ depends on ARCH_AT91SAM9RL
+ help
+ Say Y here if you have a 4-wire touchscreen connected to the
+ ADC Controller on your Atmel SoC (such as the AT91SAM9RL).
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called atmel_tsadcc.
+
+config TOUCHSCREEN_UCB1400
+ tristate "Philips UCB1400 touchscreen"
+ select AC97_BUS
+ help
+ This enables support for the Philips UCB1400 touchscreen interface.
+ The UCB1400 is an AC97 audio codec. The touchscreen interface
+ will be initialized only after the ALSA subsystem has been
+ brought up and the UCB1400 detected. You therefore have to
+ configure ALSA support as well (either built-in or modular,
+ independently of whether this driver is itself built-in or
+ modular) for this driver to work.
+
+ To compile this driver as a module, choose M here: the
+ module will be called ucb1400_ts.
+
+config TOUCHSCREEN_WM97XX
+ tristate "Support for WM97xx AC97 touchscreen controllers"
+ depends on AC97_BUS
+ help
+ Say Y here if you have a Wolfson Microelectronics WM97xx
+ touchscreen connected to your system. Note that this option
+ only enables core driver, you will also need to select
+ support for appropriate chip below.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called wm97xx-ts.
+
+config TOUCHSCREEN_WM9705
+ bool "WM9705 Touchscreen interface support"
+ depends on TOUCHSCREEN_WM97XX
+ help
+ Say Y here if you have a Wolfson Microelectronics WM9705
+ touchscreen controller connected to your system.
+
+ If unsure, say N.
+
+config TOUCHSCREEN_WM9712
+ bool "WM9712 Touchscreen interface support"
+ depends on TOUCHSCREEN_WM97XX
+ help
+ Say Y here if you have a Wolfson Microelectronics WM9712
+ touchscreen controller connected to your system.
+
+ If unsure, say N.
+
+config TOUCHSCREEN_WM9713
+ bool "WM9713 Touchscreen interface support"
+ depends on TOUCHSCREEN_WM97XX
+ help
+ Say Y here if you have a Wolfson Microelectronics WM9713 touchscreen
+ controller connected to your system.
+
+ If unsure, say N.
+
+config TOUCHSCREEN_WM97XX_MAINSTONE
+ tristate "WM97xx Mainstone accelerated touch"
+ depends on TOUCHSCREEN_WM97XX && ARCH_PXA
+ help
+ Say Y here for support for streaming mode with WM97xx touchscreens
+ on Mainstone systems.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called mainstone-wm97xx.
+
+config TOUCHSCREEN_USB_COMPOSITE
+ tristate "USB Touchscreen Driver"
+ depends on USB_ARCH_HAS_HCD
+ select USB
+ help
+ USB Touchscreen driver for:
+ - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700)
+ - PanJit TouchSet USB
+ - 3M MicroTouch USB (EX II series)
+ - ITM
+ - some other eTurboTouch
+ - Gunze AHL61
+ - DMC TSC-10/25
+ - IRTOUCHSYSTEMS/UNITOP
+ - IdealTEK URTC1000
+ - GoTop Super_Q2/GogoPen/PenPower tablets
+
+ Have a look at <http://linux.chapter7.ch/touchkit/> for
+ a usage description and the required user-space stuff.
+
+ To compile this driver as a module, choose M here: the
+ module will be called usbtouchscreen.
+
+config TOUCHSCREEN_USB_EGALAX
+ default y
+ bool "eGalax, eTurboTouch CT-410/510/700 device support" if EMBEDDED
+ depends on TOUCHSCREEN_USB_COMPOSITE
+
+config TOUCHSCREEN_USB_PANJIT
+ default y
+ bool "PanJit device support" if EMBEDDED
+ depends on TOUCHSCREEN_USB_COMPOSITE
+
+config TOUCHSCREEN_USB_3M
+ default y
+ bool "3M/Microtouch EX II series device support" if EMBEDDED
+ depends on TOUCHSCREEN_USB_COMPOSITE
+
+config TOUCHSCREEN_USB_ITM
+ default y
+ bool "ITM device support" if EMBEDDED
+ depends on TOUCHSCREEN_USB_COMPOSITE
+
+config TOUCHSCREEN_USB_ETURBO
+ default y
+ bool "eTurboTouch (non-eGalax compatible) device support" if EMBEDDED
+ depends on TOUCHSCREEN_USB_COMPOSITE
+
+config TOUCHSCREEN_USB_GUNZE
+ default y
+ bool "Gunze AHL61 device support" if EMBEDDED
+ depends on TOUCHSCREEN_USB_COMPOSITE
+
+config TOUCHSCREEN_USB_DMC_TSC10
+ default y
+ bool "DMC TSC-10/25 device support" if EMBEDDED
+ depends on TOUCHSCREEN_USB_COMPOSITE
+
+config TOUCHSCREEN_USB_IRTOUCH
+ default y
+ bool "IRTOUCHSYSTEMS/UNITOP device support" if EMBEDDED
+ depends on TOUCHSCREEN_USB_COMPOSITE
+
+config TOUCHSCREEN_USB_IDEALTEK
+ default y
+ bool "IdealTEK URTC1000 device support" if EMBEDDED
+ depends on TOUCHSCREEN_USB_COMPOSITE
+
+config TOUCHSCREEN_USB_GENERAL_TOUCH
+ default y
+ bool "GeneralTouch Touchscreen device support" if EMBEDDED
+ depends on TOUCHSCREEN_USB_COMPOSITE
+
+config TOUCHSCREEN_USB_GOTOP
+ default y
+ bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EMBEDDED
+ depends on TOUCHSCREEN_USB_COMPOSITE
+
+config TOUCHSCREEN_TOUCHIT213
+ tristate "Sahara TouchIT-213 touchscreen"
+ select SERIO
+ help
+ Say Y here if you have a Sahara TouchIT-213 Tablet PC.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called touchit213.
+
endif
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff