/*
- * Copyright (c) 2006 QLogic, Inc. All rights reserved.
+ * Copyright (c) 2006, 2007 QLogic Corporation. All rights reserved.
* Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
#include <linux/interrupt.h>
#include <linux/pci.h>
#include <linux/delay.h>
-
+#include <rdma/ib_verbs.h>
#include "ipath_kernel.h"
#include "ipath_registers.h"
+static void ipath_setup_pe_setextled(struct ipath_devdata *, u64, u64);
+
/*
* This file contains all the chip-specific register information and
* access functions for the QLogic InfiniPath PCI-Express chip.
unsigned long long Reserved12;
};
-#define IPATH_KREG_OFFSET(field) (offsetof(struct \
- _infinipath_do_not_use_kernel_regs, field) / sizeof(u64))
+struct _infinipath_do_not_use_counters {
+ __u64 LBIntCnt;
+ __u64 LBFlowStallCnt;
+ __u64 Reserved1;
+ __u64 TxUnsupVLErrCnt;
+ __u64 TxDataPktCnt;
+ __u64 TxFlowPktCnt;
+ __u64 TxDwordCnt;
+ __u64 TxLenErrCnt;
+ __u64 TxMaxMinLenErrCnt;
+ __u64 TxUnderrunCnt;
+ __u64 TxFlowStallCnt;
+ __u64 TxDroppedPktCnt;
+ __u64 RxDroppedPktCnt;
+ __u64 RxDataPktCnt;
+ __u64 RxFlowPktCnt;
+ __u64 RxDwordCnt;
+ __u64 RxLenErrCnt;
+ __u64 RxMaxMinLenErrCnt;
+ __u64 RxICRCErrCnt;
+ __u64 RxVCRCErrCnt;
+ __u64 RxFlowCtrlErrCnt;
+ __u64 RxBadFormatCnt;
+ __u64 RxLinkProblemCnt;
+ __u64 RxEBPCnt;
+ __u64 RxLPCRCErrCnt;
+ __u64 RxBufOvflCnt;
+ __u64 RxTIDFullErrCnt;
+ __u64 RxTIDValidErrCnt;
+ __u64 RxPKeyMismatchCnt;
+ __u64 RxP0HdrEgrOvflCnt;
+ __u64 RxP1HdrEgrOvflCnt;
+ __u64 RxP2HdrEgrOvflCnt;
+ __u64 RxP3HdrEgrOvflCnt;
+ __u64 RxP4HdrEgrOvflCnt;
+ __u64 RxP5HdrEgrOvflCnt;
+ __u64 RxP6HdrEgrOvflCnt;
+ __u64 RxP7HdrEgrOvflCnt;
+ __u64 RxP8HdrEgrOvflCnt;
+ __u64 Reserved6;
+ __u64 Reserved7;
+ __u64 IBStatusChangeCnt;
+ __u64 IBLinkErrRecoveryCnt;
+ __u64 IBLinkDownedCnt;
+ __u64 IBSymbolErrCnt;
+};
+
+#define IPATH_KREG_OFFSET(field) (offsetof( \
+ struct _infinipath_do_not_use_kernel_regs, field) / sizeof(u64))
#define IPATH_CREG_OFFSET(field) (offsetof( \
- struct infinipath_counters, field) / sizeof(u64))
+ struct _infinipath_do_not_use_counters, field) / sizeof(u64))
static const struct ipath_kregs ipath_pe_kregs = {
.kr_control = IPATH_KREG_OFFSET(Control),
.kr_ibpllcfg = IPATH_KREG_OFFSET(IBPLLCfg),
/*
- * These should not be used directly via ipath_read_kreg64(),
- * use them with ipath_read_kreg64_port()
+ * These should not be used directly via ipath_write_kreg64(),
+ * use them with ipath_write_kreg64_port(),
*/
.kr_rcvhdraddr = IPATH_KREG_OFFSET(RcvHdrAddr0),
.kr_rcvhdrtailaddr = IPATH_KREG_OFFSET(RcvHdrTailAddr0),
.cr_ibsymbolerrcnt = IPATH_CREG_OFFSET(IBSymbolErrCnt)
};
+/* kr_control bits */
+#define INFINIPATH_C_RESET 1U
+
/* kr_intstatus, kr_intclear, kr_intmask bits */
#define INFINIPATH_I_RCVURG_MASK ((1U<<5)-1)
+#define INFINIPATH_I_RCVURG_SHIFT 0
#define INFINIPATH_I_RCVAVAIL_MASK ((1U<<5)-1)
+#define INFINIPATH_I_RCVAVAIL_SHIFT 12
/* kr_hwerrclear, kr_hwerrmask, kr_hwerrstatus, bits */
#define INFINIPATH_HWE_PCIEMEMPARITYERR_MASK 0x000000000000003fULL
#define INFINIPATH_HWE_PCIE0PLLFAILED 0x0800000000000000ULL
#define INFINIPATH_HWE_SERDESPLLFAILED 0x1000000000000000ULL
+#define IBA6120_IBCS_LINKTRAININGSTATE_MASK 0xf
+#define IBA6120_IBCS_LINKSTATE_SHIFT 4
+
/* kr_extstatus bits */
#define INFINIPATH_EXTS_FREQSEL 0x2
#define INFINIPATH_EXTS_SERDESSEL 0x4
#define INFINIPATH_EXTS_MEMBIST_ENDTEST 0x0000000000004000
#define INFINIPATH_EXTS_MEMBIST_FOUND 0x0000000000008000
+/* kr_xgxsconfig bits */
+#define INFINIPATH_XGXS_RESET 0x5ULL
+
#define _IPATH_GPIO_SDA_NUM 1
#define _IPATH_GPIO_SCL_NUM 0
#define IPATH_GPIO_SCL (1ULL << \
(_IPATH_GPIO_SCL_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT))
-/*
- * Rev2 silicon allows suppressing check for ArmLaunch errors.
- * this can speed up short packet sends on systems that do
- * not guaranteee write-order.
- */
-#define INFINIPATH_XGXS_SUPPRESS_ARMLAUNCH_ERR (1ULL<<63)
+#define INFINIPATH_RT_BUFSIZE_MASK 0xe0000000ULL
+#define INFINIPATH_RT_BUFSIZE_SHIFTVAL(tid) \
+ ((((tid) & INFINIPATH_RT_BUFSIZE_MASK) >> 29) + 11 - 1)
+#define INFINIPATH_RT_BUFSIZE(tid) (1 << INFINIPATH_RT_BUFSIZE_SHIFTVAL(tid))
+#define INFINIPATH_RT_IS_VALID(tid) \
+ (((tid) & INFINIPATH_RT_BUFSIZE_MASK) && \
+ ((((tid) & INFINIPATH_RT_BUFSIZE_MASK) != INFINIPATH_RT_BUFSIZE_MASK)))
+#define INFINIPATH_RT_ADDR_MASK 0x1FFFFFFFULL /* 29 bits valid */
+#define INFINIPATH_RT_ADDR_SHIFT 10
+
+#define INFINIPATH_R_INTRAVAIL_SHIFT 16
+#define INFINIPATH_R_TAILUPD_SHIFT 31
/* 6120 specific hardware errors... */
static const struct ipath_hwerror_msgs ipath_6120_hwerror_msgs[] = {
INFINIPATH_HWE_MSG(SERDESPLLFAILED, "SerDes PLL"),
};
+#define TXE_PIO_PARITY ((INFINIPATH_HWE_TXEMEMPARITYERR_PIOBUF | \
+ INFINIPATH_HWE_TXEMEMPARITYERR_PIOPBC) \
+ << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT)
+#define RXE_EAGER_PARITY (INFINIPATH_HWE_RXEMEMPARITYERR_EAGERTID \
+ << INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT)
+
+static void ipath_pe_put_tid_2(struct ipath_devdata *, u64 __iomem *,
+ u32, unsigned long);
+
+/*
+ * On platforms using this chip, and not having ordered WC stores, we
+ * can get TXE parity errors due to speculative reads to the PIO buffers,
+ * and this, due to a chip bug can result in (many) false parity error
+ * reports. So it's a debug print on those, and an info print on systems
+ * where the speculative reads don't occur.
+ */
+static void ipath_pe_txe_recover(struct ipath_devdata *dd)
+{
+ if (ipath_unordered_wc())
+ ipath_dbg("Recovering from TXE PIO parity error\n");
+ else {
+ ++ipath_stats.sps_txeparity;
+ dev_info(&dd->pcidev->dev,
+ "Recovering from TXE PIO parity error\n");
+ }
+}
+
+
/**
* ipath_pe_handle_hwerrors - display hardware errors.
* @dd: the infinipath device
u32 bits, ctrl;
int isfatal = 0;
char bitsmsg[64];
+ int log_idx;
hwerrs = ipath_read_kreg64(dd, dd->ipath_kregs->kr_hwerrstatus);
if (!hwerrs) {
hwerrs &= dd->ipath_hwerrmask;
+ /* We log some errors to EEPROM, check if we have any of those. */
+ for (log_idx = 0; log_idx < IPATH_EEP_LOG_CNT; ++log_idx)
+ if (hwerrs & dd->ipath_eep_st_masks[log_idx].hwerrs_to_log)
+ ipath_inc_eeprom_err(dd, log_idx, 1);
+
/*
* make sure we get this much out, unless told to be quiet,
* or it's occurred within the last 5 seconds
*/
- if ((hwerrs & ~(dd->ipath_lasthwerror |
- ((INFINIPATH_HWE_TXEMEMPARITYERR_PIOBUF |
- INFINIPATH_HWE_TXEMEMPARITYERR_PIOPBC)
- << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT))) ||
+ if ((hwerrs & ~(dd->ipath_lasthwerror | TXE_PIO_PARITY |
+ RXE_EAGER_PARITY)) ||
(ipath_debug & __IPATH_VERBDBG))
dev_info(&dd->pcidev->dev, "Hardware error: hwerr=0x%llx "
"(cleared)\n", (unsigned long long) hwerrs);
(hwerrs & ~dd->ipath_hwe_bitsextant));
ctrl = ipath_read_kreg32(dd, dd->ipath_kregs->kr_control);
- if (ctrl & INFINIPATH_C_FREEZEMODE) {
+ if ((ctrl & INFINIPATH_C_FREEZEMODE) && !ipath_diag_inuse) {
/*
* parity errors in send memory are recoverable,
* just cancel the send (if indicated in * sendbuffererror),
* occur if a processor speculative read is done to the PIO
* buffer while we are sending a packet, for example.
*/
- if (hwerrs & ((INFINIPATH_HWE_TXEMEMPARITYERR_PIOBUF |
- INFINIPATH_HWE_TXEMEMPARITYERR_PIOPBC)
- << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT)) {
- ipath_stats.sps_txeparity++;
- ipath_dbg("Recovering from TXE parity error (%llu), "
- "hwerrstatus=%llx\n",
- (unsigned long long) ipath_stats.sps_txeparity,
- (unsigned long long) hwerrs);
- ipath_disarm_senderrbufs(dd);
- hwerrs &= ~((INFINIPATH_HWE_TXEMEMPARITYERR_PIOBUF |
- INFINIPATH_HWE_TXEMEMPARITYERR_PIOPBC)
- << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT);
- if (!hwerrs) { /* else leave in freeze mode */
- ipath_write_kreg(dd,
- dd->ipath_kregs->kr_control,
- dd->ipath_control);
- return;
- }
+ if (hwerrs & TXE_PIO_PARITY) {
+ ipath_pe_txe_recover(dd);
+ hwerrs &= ~TXE_PIO_PARITY;
}
- if (hwerrs) {
- /*
- * if any set that we aren't ignoring only make the
- * complaint once, in case it's stuck or recurring,
- * and we get here multiple times
- */
- if (dd->ipath_flags & IPATH_INITTED) {
- ipath_dev_err(dd, "Fatal Hardware Error (freeze "
- "mode), no longer usable, SN %.16s\n",
- dd->ipath_serial);
- isfatal = 1;
- }
- /*
- * Mark as having had an error for driver, and also
- * for /sys and status word mapped to user programs.
- * This marks unit as not usable, until reset
- */
- *dd->ipath_statusp &= ~IPATH_STATUS_IB_READY;
- *dd->ipath_statusp |= IPATH_STATUS_HWERROR;
- dd->ipath_flags &= ~IPATH_INITTED;
- } else {
- ipath_dbg("Clearing freezemode on ignored hardware "
- "error\n");
- ipath_write_kreg(dd, dd->ipath_kregs->kr_control,
- dd->ipath_control);
+ if (!hwerrs) {
+ static u32 freeze_cnt;
+
+ freeze_cnt++;
+ ipath_dbg("Clearing freezemode on ignored or recovered "
+ "hardware error (%u)\n", freeze_cnt);
+ ipath_clear_freeze(dd);
}
}
if (hwerrs & INFINIPATH_HWE_SERDESPLLFAILED) {
/*
- * If it occurs, it is left masked since the eternal
+ * If it occurs, it is left masked since the external
* interface is unused
*/
dd->ipath_hwerrmask &= ~INFINIPATH_HWE_SERDESPLLFAILED;
dd->ipath_hwerrmask);
}
- ipath_dev_err(dd, "%s hardware error\n", msg);
- if (isfatal && !ipath_diag_inuse && dd->ipath_freezemsg) {
+ if (hwerrs) {
/*
- * for /sys status file ; if no trailing } is copied, we'll
- * know it was truncated.
+ * if any set that we aren't ignoring; only
+ * make the complaint once, in case it's stuck
+ * or recurring, and we get here multiple
+ * times.
+ */
+ ipath_dev_err(dd, "%s hardware error\n", msg);
+ if (dd->ipath_flags & IPATH_INITTED) {
+ ipath_set_linkstate(dd, IPATH_IB_LINKDOWN);
+ ipath_setup_pe_setextled(dd,
+ INFINIPATH_IBCS_L_STATE_DOWN,
+ INFINIPATH_IBCS_LT_STATE_DISABLED);
+ ipath_dev_err(dd, "Fatal Hardware Error (freeze "
+ "mode), no longer usable, SN %.16s\n",
+ dd->ipath_serial);
+ isfatal = 1;
+ }
+ *dd->ipath_statusp &= ~IPATH_STATUS_IB_READY;
+ /* mark as having had error */
+ *dd->ipath_statusp |= IPATH_STATUS_HWERROR;
+ /*
+ * mark as not usable, at a minimum until driver
+ * is reloaded, probably until reboot, since no
+ * other reset is possible.
+ */
+ dd->ipath_flags &= ~IPATH_INITTED;
+ } else
+ *msg = 0; /* recovered from all of them */
+
+ if (isfatal && !ipath_diag_inuse && dd->ipath_freezemsg && msg) {
+ /*
+ * for /sys status file ; if no trailing brace is copied,
+ * we'll know it was truncated.
*/
snprintf(dd->ipath_freezemsg, dd->ipath_freezelen,
"{%s}", msg);
ipath_dev_err(dd, "Unsupported InfiniPath hardware revision %u.%u!\n",
dd->ipath_majrev, dd->ipath_minrev);
ret = 1;
- } else
+ } else {
ret = 0;
+ if (dd->ipath_minrev >= 2)
+ dd->ipath_f_put_tid = ipath_pe_put_tid_2;
+ }
+
+ /*
+ * set here, not in ipath_init_*_funcs because we have to do
+ * it after we can read chip registers.
+ */
+ dd->ipath_ureg_align =
+ ipath_read_kreg32(dd, dd->ipath_kregs->kr_pagealign);
return ret;
}
if (!(extsval & INFINIPATH_EXTS_MEMBIST_ENDTEST))
ipath_dev_err(dd, "MemBIST did not complete!\n");
+ if (extsval & INFINIPATH_EXTS_MEMBIST_FOUND)
+ ipath_dbg("MemBIST corrected\n");
val = ~0ULL; /* barring bugs, all hwerrors become interrupts, */
val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig);
prev_val = val;
- if (((val >> INFINIPATH_XGXS_MDIOADDR_SHIFT) &
- INFINIPATH_XGXS_MDIOADDR_MASK) != 3) {
- val &=
- ~(INFINIPATH_XGXS_MDIOADDR_MASK <<
- INFINIPATH_XGXS_MDIOADDR_SHIFT);
- /* MDIO address 3 */
- val |= 3ULL << INFINIPATH_XGXS_MDIOADDR_SHIFT;
- }
- if (val & INFINIPATH_XGXS_RESET) {
+ if (val & INFINIPATH_XGXS_RESET)
val &= ~INFINIPATH_XGXS_RESET;
- }
if (((val >> INFINIPATH_XGXS_RX_POL_SHIFT) &
INFINIPATH_XGXS_RX_POL_MASK) != dd->ipath_rx_pol_inv ) {
/* need to compensate for Tx inversion in partner */
val |= dd->ipath_rx_pol_inv <<
INFINIPATH_XGXS_RX_POL_SHIFT;
}
- if (dd->ipath_minrev >= 2) {
- /* Rev 2. can tolerate multiple writes to PBC, and
- * allowing them can provide lower latency on some
- * CPUs, but this feature is off by default, only
- * turned on by setting D63 of XGXSconfig reg.
- * May want to make this conditional more
- * fine-grained in future. This is not exactly
- * related to XGXS, but where the bit ended up.
- */
- val |= INFINIPATH_XGXS_SUPPRESS_ARMLAUNCH_ERR;
- }
if (val != prev_val)
ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, val);
(unsigned long long)
ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig));
- if (!ipath_waitfor_mdio_cmdready(dd)) {
- ipath_write_kreg(
- dd, dd->ipath_kregs->kr_mdio,
- ipath_mdio_req(IPATH_MDIO_CMD_READ, 31,
- IPATH_MDIO_CTRL_XGXS_REG_8, 0));
- if (ipath_waitfor_complete(dd, dd->ipath_kregs->kr_mdio,
- IPATH_MDIO_DATAVALID, &val))
- ipath_dbg("Never got MDIO data for XGXS "
- "status read\n");
- else
- ipath_cdbg(VERBOSE, "MDIO Read reg8, "
- "'bank' 31 %x\n", (u32) val);
- } else
- ipath_dbg("Never got MDIO cmdready for XGXS status read\n");
-
return ret;
}
static int ipath_pe_intconfig(struct ipath_devdata *dd)
{
- u64 val;
u32 chiprev;
/*
if ((chiprev & INFINIPATH_R_CHIPREVMINOR_MASK) > 1) {
/* Rev2+ reports extra errors via internal GPIO pins */
dd->ipath_flags |= IPATH_GPIO_ERRINTRS;
- val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_gpio_mask);
- val |= IPATH_GPIO_ERRINTR_MASK;
- ipath_write_kreg( dd, dd->ipath_kregs->kr_gpio_mask, val);
+ dd->ipath_gpio_mask |= IPATH_GPIO_ERRINTR_MASK;
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_gpio_mask,
+ dd->ipath_gpio_mask);
}
return 0;
}
u64 ltst)
{
u64 extctl;
+ unsigned long flags = 0;
/* the diags use the LED to indicate diag info, so we leave
* the external LED alone when the diags are running */
if (ipath_diag_inuse)
return;
+ /* Allow override of LED display for, e.g. Locating system in rack */
+ if (dd->ipath_led_override) {
+ ltst = (dd->ipath_led_override & IPATH_LED_PHYS)
+ ? INFINIPATH_IBCS_LT_STATE_LINKUP
+ : INFINIPATH_IBCS_LT_STATE_DISABLED;
+ lst = (dd->ipath_led_override & IPATH_LED_LOG)
+ ? INFINIPATH_IBCS_L_STATE_ACTIVE
+ : INFINIPATH_IBCS_L_STATE_DOWN;
+ }
+
+ spin_lock_irqsave(&dd->ipath_gpio_lock, flags);
extctl = dd->ipath_extctrl & ~(INFINIPATH_EXTC_LED1PRIPORT_ON |
INFINIPATH_EXTC_LED2PRIPORT_ON);
- if (ltst & INFINIPATH_IBCS_LT_STATE_LINKUP)
+ if (ltst == INFINIPATH_IBCS_LT_STATE_LINKUP)
extctl |= INFINIPATH_EXTC_LED2PRIPORT_ON;
if (lst == INFINIPATH_IBCS_L_STATE_ACTIVE)
extctl |= INFINIPATH_EXTC_LED1PRIPORT_ON;
dd->ipath_extctrl = extctl;
ipath_write_kreg(dd, dd->ipath_kregs->kr_extctrl, extctl);
+ spin_unlock_irqrestore(&dd->ipath_gpio_lock, flags);
}
/**
pci_disable_msi(dd->pcidev);
}
+static void ipath_6120_pcie_params(struct ipath_devdata *dd)
+{
+ u16 linkstat, speed;
+ int pos;
+
+ pos = pci_find_capability(dd->pcidev, PCI_CAP_ID_EXP);
+ if (!pos) {
+ ipath_dev_err(dd, "Can't find PCI Express capability!\n");
+ goto bail;
+ }
+
+ pci_read_config_word(dd->pcidev, pos + PCI_EXP_LNKSTA,
+ &linkstat);
+ /*
+ * speed is bits 0-4, linkwidth is bits 4-8
+ * no defines for them in headers
+ */
+ speed = linkstat & 0xf;
+ linkstat >>= 4;
+ linkstat &= 0x1f;
+ dd->ipath_lbus_width = linkstat;
+
+ switch (speed) {
+ case 1:
+ dd->ipath_lbus_speed = 2500; /* Gen1, 2.5GHz */
+ break;
+ case 2:
+ dd->ipath_lbus_speed = 5000; /* Gen1, 5GHz */
+ break;
+ default: /* not defined, assume gen1 */
+ dd->ipath_lbus_speed = 2500;
+ break;
+ }
+
+ if (linkstat < 8)
+ ipath_dev_err(dd,
+ "PCIe width %u (x8 HCA), performance reduced\n",
+ linkstat);
+ else
+ ipath_cdbg(VERBOSE, "PCIe speed %u width %u (x8 HCA)\n",
+ dd->ipath_lbus_speed, linkstat);
+
+ if (speed != 1)
+ ipath_dev_err(dd,
+ "PCIe linkspeed %u is incorrect; "
+ "should be 1 (2500)!\n", speed);
+bail:
+ /* fill in string, even on errors */
+ snprintf(dd->ipath_lbus_info, sizeof(dd->ipath_lbus_info),
+ "PCIe,%uMHz,x%u\n",
+ dd->ipath_lbus_speed,
+ dd->ipath_lbus_width);
+
+ return;
+}
+
/**
* ipath_setup_pe_config - setup PCIe config related stuff
* @dd: the infinipath device
} else
ipath_dev_err(dd, "Can't find MSI capability, "
"can't save MSI settings for reset\n");
- if ((pos = pci_find_capability(dd->pcidev, PCI_CAP_ID_EXP))) {
- u16 linkstat;
- pci_read_config_word(dd->pcidev, pos + PCI_EXP_LNKSTA,
- &linkstat);
- linkstat >>= 4;
- linkstat &= 0x1f;
- if (linkstat != 8)
- ipath_dev_err(dd, "PCIe width %u, "
- "performance reduced\n", linkstat);
- }
- else
- ipath_dev_err(dd, "Can't find PCI Express "
- "capability!\n");
+
+ ipath_6120_pcie_params(dd);
+
+ dd->ipath_link_width_supported = IB_WIDTH_1X | IB_WIDTH_4X;
+ dd->ipath_link_speed_supported = IPATH_IB_SDR;
+ dd->ipath_link_width_enabled = IB_WIDTH_4X;
+ dd->ipath_link_speed_enabled = dd->ipath_link_speed_supported;
+ /* these can't change for this chip, so set once */
+ dd->ipath_link_width_active = dd->ipath_link_width_enabled;
+ dd->ipath_link_speed_active = dd->ipath_link_speed_enabled;
return 0;
}
static void ipath_init_pe_variables(struct ipath_devdata *dd)
{
/*
+ * setup the register offsets, since they are different for each
+ * chip
+ */
+ dd->ipath_kregs = &ipath_pe_kregs;
+ dd->ipath_cregs = &ipath_pe_cregs;
+
+ /*
* bits for selecting i2c direction and values,
* used for I2C serial flash
*/
dd->ipath_gpio_sda = IPATH_GPIO_SDA;
dd->ipath_gpio_scl = IPATH_GPIO_SCL;
+ /*
+ * Fill in data for field-values that change in newer chips.
+ * We dynamically specify only the mask for LINKTRAININGSTATE
+ * and only the shift for LINKSTATE, as they are the only ones
+ * that change. Also precalculate the 3 link states of interest
+ * and the combined mask.
+ */
+ dd->ibcs_ls_shift = IBA6120_IBCS_LINKSTATE_SHIFT;
+ dd->ibcs_lts_mask = IBA6120_IBCS_LINKTRAININGSTATE_MASK;
+ dd->ibcs_mask = (INFINIPATH_IBCS_LINKSTATE_MASK <<
+ dd->ibcs_ls_shift) | dd->ibcs_lts_mask;
+ dd->ib_init = (INFINIPATH_IBCS_LT_STATE_LINKUP <<
+ INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) |
+ (INFINIPATH_IBCS_L_STATE_INIT << dd->ibcs_ls_shift);
+ dd->ib_arm = (INFINIPATH_IBCS_LT_STATE_LINKUP <<
+ INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) |
+ (INFINIPATH_IBCS_L_STATE_ARM << dd->ibcs_ls_shift);
+ dd->ib_active = (INFINIPATH_IBCS_LT_STATE_LINKUP <<
+ INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) |
+ (INFINIPATH_IBCS_L_STATE_ACTIVE << dd->ibcs_ls_shift);
+
+ /*
+ * Fill in data for ibcc field-values that change in newer chips.
+ * We dynamically specify only the mask for LINKINITCMD
+ * and only the shift for LINKCMD and MAXPKTLEN, as they are
+ * the only ones that change.
+ */
+ dd->ibcc_lic_mask = INFINIPATH_IBCC_LINKINITCMD_MASK;
+ dd->ibcc_lc_shift = INFINIPATH_IBCC_LINKCMD_SHIFT;
+ dd->ibcc_mpl_shift = INFINIPATH_IBCC_MAXPKTLEN_SHIFT;
+
+ /* Fill in shifts for RcvCtrl. */
+ dd->ipath_r_portenable_shift = INFINIPATH_R_PORTENABLE_SHIFT;
+ dd->ipath_r_intravail_shift = INFINIPATH_R_INTRAVAIL_SHIFT;
+ dd->ipath_r_tailupd_shift = INFINIPATH_R_TAILUPD_SHIFT;
+ dd->ipath_r_portcfg_shift = 0; /* Not on IBA6120 */
+
/* variables for sanity checking interrupt and errors */
dd->ipath_hwe_bitsextant =
(INFINIPATH_HWE_RXEMEMPARITYERR_MASK <<
dd->ipath_i_rcvavail_mask = INFINIPATH_I_RCVAVAIL_MASK;
dd->ipath_i_rcvurg_mask = INFINIPATH_I_RCVURG_MASK;
+ dd->ipath_i_rcvavail_shift = INFINIPATH_I_RCVAVAIL_SHIFT;
+ dd->ipath_i_rcvurg_shift = INFINIPATH_I_RCVURG_SHIFT;
+
+ /*
+ * EEPROM error log 0 is TXE Parity errors. 1 is RXE Parity.
+ * 2 is Some Misc, 3 is reserved for future.
+ */
+ dd->ipath_eep_st_masks[0].hwerrs_to_log =
+ INFINIPATH_HWE_TXEMEMPARITYERR_MASK <<
+ INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT;
+
+ /* Ignore errors in PIO/PBC on systems with unordered write-combining */
+ if (ipath_unordered_wc())
+ dd->ipath_eep_st_masks[0].hwerrs_to_log &= ~TXE_PIO_PARITY;
+
+ dd->ipath_eep_st_masks[1].hwerrs_to_log =
+ INFINIPATH_HWE_RXEMEMPARITYERR_MASK <<
+ INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT;
+
+ dd->ipath_eep_st_masks[2].errs_to_log = INFINIPATH_E_RESET;
+ dd->delay_mult = 2; /* SDR, 4X, can't change */
}
/* setup the MSI stuff again after a reset. I'd like to just call
u64 val;
int i;
int ret;
+ u16 cmdval;
+
+ pci_read_config_word(dd->pcidev, PCI_COMMAND, &cmdval);
/* Use ERROR so it shows up in logs, etc. */
ipath_dev_err(dd, "Resetting InfiniPath unit %u\n", dd->ipath_unit);
ipath_dev_err(dd, "rewrite of BAR1 failed: %d\n",
r);
/* now re-enable memory access */
+ pci_write_config_word(dd->pcidev, PCI_COMMAND, cmdval);
if ((r = pci_enable_device(dd->pcidev)))
ipath_dev_err(dd, "pci_enable_device failed after "
"reset: %d\n", r);
- /* whether it worked or not, mark as present, again */
+ /*
+ * whether it fully enabled or not, mark as present,
+ * again (but not INITTED)
+ */
dd->ipath_flags |= IPATH_PRESENT;
val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_revision);
if (val == dd->ipath_revision) {
ret = 0; /* failed */
bail:
+ if (ret)
+ ipath_6120_pcie_params(dd);
return ret;
}
* ipath_pe_put_tid - write a TID in chip
* @dd: the infinipath device
* @tidptr: pointer to the expected TID (in chip) to udpate
- * @tidtype: 0 for eager, 1 for expected
+ * @tidtype: RCVHQ_RCV_TYPE_EAGER (1) for eager, RCVHQ_RCV_TYPE_EXPECTED (0) for expected
* @pa: physical address of in memory buffer; ipath_tidinvalid if freeing
*
* This exists as a separate routine to allow for special locking etc.
{
u32 __iomem *tidp32 = (u32 __iomem *)tidptr;
unsigned long flags = 0; /* keep gcc quiet */
+ int tidx;
+ spinlock_t *tidlockp;
+
+ if (!dd->ipath_kregbase)
+ return;
if (pa != dd->ipath_tidinvalid) {
if (pa & ((1U << 11) - 1)) {
dev_info(&dd->pcidev->dev, "BUG: physaddr %lx "
- "not 4KB aligned!\n", pa);
+ "not 2KB aligned!\n", pa);
return;
}
pa >>= 11;
/* paranoia check */
- if (pa & (7<<29))
+ if (pa & ~INFINIPATH_RT_ADDR_MASK)
ipath_dev_err(dd,
"BUG: Physical page address 0x%lx "
"has bits set in 31-29\n", pa);
- if (type == 0)
+ if (type == RCVHQ_RCV_TYPE_EAGER)
pa |= dd->ipath_tidtemplate;
else /* for now, always full 4KB page */
pa |= 2 << 29;
}
- /* workaround chip bug 9437 by writing each TID twice
- * and holding a spinlock around the writes, so they don't
- * intermix with other TID (eager or expected) writes
- * Unfortunately, this call can be done from interrupt level
- * for the port 0 eager TIDs, so we have to use irqsave
+ /*
+ * Workaround chip bug 9437 by writing the scratch register
+ * before and after the TID, and with an io write barrier.
+ * We use a spinlock around the writes, so they can't intermix
+ * with other TID (eager or expected) writes (the chip bug
+ * is triggered by back to back TID writes). Unfortunately, this
+ * call can be done from interrupt level for the port 0 eager TIDs,
+ * so we have to use irqsave locks.
+ */
+ /*
+ * Assumes tidptr always > ipath_egrtidbase
+ * if type == RCVHQ_RCV_TYPE_EAGER.
*/
- spin_lock_irqsave(&dd->ipath_tid_lock, flags);
+ tidx = tidptr - dd->ipath_egrtidbase;
+
+ tidlockp = (type == RCVHQ_RCV_TYPE_EAGER && tidx < dd->ipath_rcvegrcnt)
+ ? &dd->ipath_kernel_tid_lock : &dd->ipath_user_tid_lock;
+ spin_lock_irqsave(tidlockp, flags);
ipath_write_kreg(dd, dd->ipath_kregs->kr_scratch, 0xfeeddeaf);
- if (dd->ipath_kregbase)
- writel(pa, tidp32);
+ writel(pa, tidp32);
ipath_write_kreg(dd, dd->ipath_kregs->kr_scratch, 0xdeadbeef);
mmiowb();
- spin_unlock_irqrestore(&dd->ipath_tid_lock, flags);
+ spin_unlock_irqrestore(tidlockp, flags);
}
+
/**
* ipath_pe_put_tid_2 - write a TID in chip, Revision 2 or higher
* @dd: the infinipath device
* @tidptr: pointer to the expected TID (in chip) to udpate
- * @tidtype: 0 for eager, 1 for expected
+ * @tidtype: RCVHQ_RCV_TYPE_EAGER (1) for eager, RCVHQ_RCV_TYPE_EXPECTED (0) for expected
* @pa: physical address of in memory buffer; ipath_tidinvalid if freeing
*
* This exists as a separate routine to allow for selection of the
u32 type, unsigned long pa)
{
u32 __iomem *tidp32 = (u32 __iomem *)tidptr;
+ u32 tidx;
+
+ if (!dd->ipath_kregbase)
+ return;
if (pa != dd->ipath_tidinvalid) {
if (pa & ((1U << 11) - 1)) {
}
pa >>= 11;
/* paranoia check */
- if (pa & (7<<29))
+ if (pa & ~INFINIPATH_RT_ADDR_MASK)
ipath_dev_err(dd,
"BUG: Physical page address 0x%lx "
"has bits set in 31-29\n", pa);
- if (type == 0)
+ if (type == RCVHQ_RCV_TYPE_EAGER)
pa |= dd->ipath_tidtemplate;
else /* for now, always full 4KB page */
pa |= 2 << 29;
}
- if (dd->ipath_kregbase)
- writel(pa, tidp32);
+ tidx = tidptr - dd->ipath_egrtidbase;
+ writel(pa, tidp32);
mmiowb();
}
port * dd->ipath_rcvtidcnt * sizeof(*tidbase));
for (i = 0; i < dd->ipath_rcvtidcnt; i++)
- ipath_pe_put_tid(dd, &tidbase[i], 0, tidinv);
+ dd->ipath_f_put_tid(dd, &tidbase[i], RCVHQ_RCV_TYPE_EXPECTED,
+ tidinv);
tidbase = (u64 __iomem *)
((char __iomem *)(dd->ipath_kregbase) +
port * dd->ipath_rcvegrcnt * sizeof(*tidbase));
for (i = 0; i < dd->ipath_rcvegrcnt; i++)
- ipath_pe_put_tid(dd, &tidbase[i], 1, tidinv);
+ dd->ipath_f_put_tid(dd, &tidbase[i], RCVHQ_RCV_TYPE_EAGER,
+ tidinv);
}
/**
static int ipath_pe_early_init(struct ipath_devdata *dd)
{
dd->ipath_flags |= IPATH_4BYTE_TID;
+ if (ipath_unordered_wc())
+ dd->ipath_flags |= IPATH_PIO_FLUSH_WC;
/*
* For openfabrics, we need to be able to handle an IB header of
*/
dd->ipath_rcvhdrentsize = 24;
dd->ipath_rcvhdrsize = IPATH_DFLT_RCVHDRSIZE;
+ dd->ipath_rhf_offset = 0;
+ dd->ipath_egrtidbase = (u64 __iomem *)
+ ((char __iomem *) dd->ipath_kregbase + dd->ipath_rcvegrbase);
- /*
- * To truly support a 4KB MTU (for usermode), we need to
- * bump this to a larger value. For now, we use them for
- * the kernel only.
- */
- dd->ipath_rcvegrbufsize = 2048;
+ dd->ipath_rcvegrbufsize = ipath_mtu4096 ? 4096 : 2048;
/*
* the min() check here is currently a nop, but it may not always
* be, depending on just how we do ipath_rcvegrbufsize
*/
- dd->ipath_ibmaxlen = min(dd->ipath_piosize2k,
+ dd->ipath_ibmaxlen = min(ipath_mtu4096 ? dd->ipath_piosize4k :
+ dd->ipath_piosize2k,
dd->ipath_rcvegrbufsize +
(dd->ipath_rcvhdrentsize << 2));
dd->ipath_init_ibmaxlen = dd->ipath_ibmaxlen;
dd = pd->port_dd;
- if (dd != NULL && dd->ipath_minrev >= 2) {
- ipath_cdbg(PROC, "IBA6120 Rev2, allow multiple PBC write\n");
- kinfo->spi_runtime_flags |= IPATH_RUNTIME_PBC_REWRITE;
- ipath_cdbg(PROC, "IBA6120 Rev2, allow loose DMA alignment\n");
- kinfo->spi_runtime_flags |= IPATH_RUNTIME_LOOSE_DMA_ALIGN;
- }
-
done:
- kinfo->spi_runtime_flags |= IPATH_RUNTIME_PCIE;
+ kinfo->spi_runtime_flags |= IPATH_RUNTIME_PCIE |
+ IPATH_RUNTIME_FORCE_PIOAVAIL | IPATH_RUNTIME_PIO_REGSWAPPED;
return 0;
}
dd->ipath_irq = 0;
}
+
+static struct ipath_message_header *
+ipath_pe_get_msgheader(struct ipath_devdata *dd, __le32 *rhf_addr)
+{
+ return (struct ipath_message_header *)
+ &rhf_addr[sizeof(u64) / sizeof(u32)];
+}
+
+static void ipath_pe_config_ports(struct ipath_devdata *dd, ushort cfgports)
+{
+ dd->ipath_portcnt =
+ ipath_read_kreg32(dd, dd->ipath_kregs->kr_portcnt);
+ dd->ipath_p0_rcvegrcnt =
+ ipath_read_kreg32(dd, dd->ipath_kregs->kr_rcvegrcnt);
+}
+
+static void ipath_pe_read_counters(struct ipath_devdata *dd,
+ struct infinipath_counters *cntrs)
+{
+ cntrs->LBIntCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(LBIntCnt));
+ cntrs->LBFlowStallCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(LBFlowStallCnt));
+ cntrs->TxSDmaDescCnt = 0;
+ cntrs->TxUnsupVLErrCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(TxUnsupVLErrCnt));
+ cntrs->TxDataPktCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(TxDataPktCnt));
+ cntrs->TxFlowPktCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(TxFlowPktCnt));
+ cntrs->TxDwordCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(TxDwordCnt));
+ cntrs->TxLenErrCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(TxLenErrCnt));
+ cntrs->TxMaxMinLenErrCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(TxMaxMinLenErrCnt));
+ cntrs->TxUnderrunCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(TxUnderrunCnt));
+ cntrs->TxFlowStallCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(TxFlowStallCnt));
+ cntrs->TxDroppedPktCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(TxDroppedPktCnt));
+ cntrs->RxDroppedPktCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxDroppedPktCnt));
+ cntrs->RxDataPktCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxDataPktCnt));
+ cntrs->RxFlowPktCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxFlowPktCnt));
+ cntrs->RxDwordCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxDwordCnt));
+ cntrs->RxLenErrCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxLenErrCnt));
+ cntrs->RxMaxMinLenErrCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxMaxMinLenErrCnt));
+ cntrs->RxICRCErrCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxICRCErrCnt));
+ cntrs->RxVCRCErrCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxVCRCErrCnt));
+ cntrs->RxFlowCtrlErrCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxFlowCtrlErrCnt));
+ cntrs->RxBadFormatCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxBadFormatCnt));
+ cntrs->RxLinkProblemCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxLinkProblemCnt));
+ cntrs->RxEBPCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxEBPCnt));
+ cntrs->RxLPCRCErrCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxLPCRCErrCnt));
+ cntrs->RxBufOvflCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxBufOvflCnt));
+ cntrs->RxTIDFullErrCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxTIDFullErrCnt));
+ cntrs->RxTIDValidErrCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxTIDValidErrCnt));
+ cntrs->RxPKeyMismatchCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxPKeyMismatchCnt));
+ cntrs->RxP0HdrEgrOvflCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxP0HdrEgrOvflCnt));
+ cntrs->RxP1HdrEgrOvflCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxP1HdrEgrOvflCnt));
+ cntrs->RxP2HdrEgrOvflCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxP2HdrEgrOvflCnt));
+ cntrs->RxP3HdrEgrOvflCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxP3HdrEgrOvflCnt));
+ cntrs->RxP4HdrEgrOvflCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxP4HdrEgrOvflCnt));
+ cntrs->RxP5HdrEgrOvflCnt = 0;
+ cntrs->RxP6HdrEgrOvflCnt = 0;
+ cntrs->RxP7HdrEgrOvflCnt = 0;
+ cntrs->RxP8HdrEgrOvflCnt = 0;
+ cntrs->RxP9HdrEgrOvflCnt = 0;
+ cntrs->RxP10HdrEgrOvflCnt = 0;
+ cntrs->RxP11HdrEgrOvflCnt = 0;
+ cntrs->RxP12HdrEgrOvflCnt = 0;
+ cntrs->RxP13HdrEgrOvflCnt = 0;
+ cntrs->RxP14HdrEgrOvflCnt = 0;
+ cntrs->RxP15HdrEgrOvflCnt = 0;
+ cntrs->RxP16HdrEgrOvflCnt = 0;
+ cntrs->IBStatusChangeCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(IBStatusChangeCnt));
+ cntrs->IBLinkErrRecoveryCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(IBLinkErrRecoveryCnt));
+ cntrs->IBLinkDownedCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(IBLinkDownedCnt));
+ cntrs->IBSymbolErrCnt =
+ ipath_snap_cntr(dd, IPATH_CREG_OFFSET(IBSymbolErrCnt));
+ cntrs->RxVL15DroppedPktCnt = 0;
+ cntrs->RxOtherLocalPhyErrCnt = 0;
+ cntrs->PcieRetryBufDiagQwordCnt = 0;
+ cntrs->ExcessBufferOvflCnt = dd->ipath_overrun_thresh_errs;
+ cntrs->LocalLinkIntegrityErrCnt = dd->ipath_lli_errs;
+ cntrs->RxVlErrCnt = 0;
+ cntrs->RxDlidFltrCnt = 0;
+}
+
+
+/* no interrupt fallback for these chips */
+static int ipath_pe_nointr_fallback(struct ipath_devdata *dd)
+{
+ return 0;
+}
+
+
+/*
+ * reset the XGXS (between serdes and IBC). Slightly less intrusive
+ * than resetting the IBC or external link state, and useful in some
+ * cases to cause some retraining. To do this right, we reset IBC
+ * as well.
+ */
+static void ipath_pe_xgxs_reset(struct ipath_devdata *dd)
+{
+ u64 val, prev_val;
+
+ prev_val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig);
+ val = prev_val | INFINIPATH_XGXS_RESET;
+ prev_val &= ~INFINIPATH_XGXS_RESET; /* be sure */
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_control,
+ dd->ipath_control & ~INFINIPATH_C_LINKENABLE);
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, val);
+ ipath_read_kreg32(dd, dd->ipath_kregs->kr_scratch);
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, prev_val);
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_control,
+ dd->ipath_control);
+}
+
+
+static int ipath_pe_get_ib_cfg(struct ipath_devdata *dd, int which)
+{
+ int ret;
+
+ switch (which) {
+ case IPATH_IB_CFG_LWID:
+ ret = dd->ipath_link_width_active;
+ break;
+ case IPATH_IB_CFG_SPD:
+ ret = dd->ipath_link_speed_active;
+ break;
+ case IPATH_IB_CFG_LWID_ENB:
+ ret = dd->ipath_link_width_enabled;
+ break;
+ case IPATH_IB_CFG_SPD_ENB:
+ ret = dd->ipath_link_speed_enabled;
+ break;
+ default:
+ ret = -ENOTSUPP;
+ break;
+ }
+ return ret;
+}
+
+
+/* we assume range checking is already done, if needed */
+static int ipath_pe_set_ib_cfg(struct ipath_devdata *dd, int which, u32 val)
+{
+ int ret = 0;
+
+ if (which == IPATH_IB_CFG_LWID_ENB)
+ dd->ipath_link_width_enabled = val;
+ else if (which == IPATH_IB_CFG_SPD_ENB)
+ dd->ipath_link_speed_enabled = val;
+ else
+ ret = -ENOTSUPP;
+ return ret;
+}
+
+static void ipath_pe_config_jint(struct ipath_devdata *dd, u16 a, u16 b)
+{
+}
+
+
+static int ipath_pe_ib_updown(struct ipath_devdata *dd, int ibup, u64 ibcs)
+{
+ ipath_setup_pe_setextled(dd, ipath_ib_linkstate(dd, ibcs),
+ ipath_ib_linktrstate(dd, ibcs));
+ return 0;
+}
+
+
/**
* ipath_init_iba6120_funcs - set up the chip-specific function pointers
* @dd: the infinipath device
dd->ipath_f_quiet_serdes = ipath_pe_quiet_serdes;
dd->ipath_f_bringup_serdes = ipath_pe_bringup_serdes;
dd->ipath_f_clear_tids = ipath_pe_clear_tids;
- if (dd->ipath_minrev >= 2)
- dd->ipath_f_put_tid = ipath_pe_put_tid_2;
- else
- dd->ipath_f_put_tid = ipath_pe_put_tid;
+ /*
+ * _f_put_tid may get changed after we read the chip revision,
+ * but we start with the safe version for all revs
+ */
+ dd->ipath_f_put_tid = ipath_pe_put_tid;
dd->ipath_f_cleanup = ipath_setup_pe_cleanup;
dd->ipath_f_setextled = ipath_setup_pe_setextled;
dd->ipath_f_get_base_info = ipath_pe_get_base_info;
dd->ipath_f_free_irq = ipath_pe_free_irq;
-
- /* initialize chip-specific variables */
dd->ipath_f_tidtemplate = ipath_pe_tidtemplate;
+ dd->ipath_f_intr_fallback = ipath_pe_nointr_fallback;
+ dd->ipath_f_xgxs_reset = ipath_pe_xgxs_reset;
+ dd->ipath_f_get_msgheader = ipath_pe_get_msgheader;
+ dd->ipath_f_config_ports = ipath_pe_config_ports;
+ dd->ipath_f_read_counters = ipath_pe_read_counters;
+ dd->ipath_f_get_ib_cfg = ipath_pe_get_ib_cfg;
+ dd->ipath_f_set_ib_cfg = ipath_pe_set_ib_cfg;
+ dd->ipath_f_config_jint = ipath_pe_config_jint;
+ dd->ipath_f_ib_updown = ipath_pe_ib_updown;
- /*
- * setup the register offsets, since they are different for each
- * chip
- */
- dd->ipath_kregs = &ipath_pe_kregs;
- dd->ipath_cregs = &ipath_pe_cregs;
+ /* initialize chip-specific variables */
ipath_init_pe_variables(dd);
}