* - delay inquiry
* Wait extra SBP2_INQUIRY_DELAY seconds after login before SCSI inquiry.
*
+ * - power condition
+ * Set the power condition field in the START STOP UNIT commands sent by
+ * sd_mod on suspend, resume, and shutdown (if manage_start_stop is on).
+ * Some disks need this to spin down or to resume properly.
+ *
* - override internal blacklist
* Instead of adding to the built-in blacklist, use only the workarounds
* specified in the module load parameter.
", skip mode page 8 = " __stringify(SBP2_WORKAROUND_MODE_SENSE_8)
", fix capacity = " __stringify(SBP2_WORKAROUND_FIX_CAPACITY)
", delay inquiry = " __stringify(SBP2_WORKAROUND_DELAY_INQUIRY)
+ ", set power condition in start stop unit = "
+ __stringify(SBP2_WORKAROUND_POWER_CONDITION)
", override internal blacklist = " __stringify(SBP2_WORKAROUND_OVERRIDE)
", or a combination)");
.firmware_revision = 0x002800,
.model_id = 0x001010,
.workarounds = SBP2_WORKAROUND_INQUIRY_36 |
- SBP2_WORKAROUND_MODE_SENSE_8,
+ SBP2_WORKAROUND_MODE_SENSE_8 |
+ SBP2_WORKAROUND_POWER_CONDITION,
},
/* DViCO Momobay FX-3A with TSB42AA9A bridge */ {
.firmware_revision = 0x002800,
.model_id = 0x000000,
- .workarounds = SBP2_WORKAROUND_DELAY_INQUIRY,
+ .workarounds = SBP2_WORKAROUND_DELAY_INQUIRY |
+ SBP2_WORKAROUND_POWER_CONDITION,
},
/* Initio bridges, actually only needed for some older ones */ {
.firmware_revision = 0x000200,
.model_id = SBP2_ROM_VALUE_WILDCARD,
.workarounds = SBP2_WORKAROUND_INQUIRY_36,
},
+ /* PL-3507 bridge with Prolific firmware */ {
+ .firmware_revision = 0x012800,
+ .model_id = SBP2_ROM_VALUE_WILDCARD,
+ .workarounds = SBP2_WORKAROUND_POWER_CONDITION,
+ },
/* Symbios bridge */ {
.firmware_revision = 0xa0b800,
.model_id = SBP2_ROM_VALUE_WILDCARD,
cmd->Current_SCpnt = Current_SCpnt;
list_add_tail(&cmd->list, &lu->cmd_orb_inuse);
} else
- SBP2_ERR("%s: no orbs available", __FUNCTION__);
+ SBP2_ERR("%s: no orbs available", __func__);
spin_unlock_irqrestore(&lu->cmd_orb_lock, flags);
return cmd;
}
{
struct sbp2_lu *lu = ud->device.driver_data;
- if (sbp2_reconnect_device(lu)) {
- /* Reconnect has failed. Perhaps we didn't reconnect fast
- * enough. Try a regular login, but first log out just in
- * case of any weirdness. */
+ if (sbp2_reconnect_device(lu) != 0) {
+ /*
+ * Reconnect failed. If another bus reset happened,
+ * let nodemgr proceed and call sbp2_update again later
+ * (or sbp2_remove if this node went away).
+ */
+ if (!hpsb_node_entry_valid(lu->ne))
+ return 0;
+ /*
+ * Or the target rejected the reconnect because we weren't
+ * fast enough. Try a regular login, but first log out
+ * just in case of any weirdness.
+ */
sbp2_logout_device(lu);
- if (sbp2_login_device(lu)) {
- /* Login failed too, just fail, and the backend
- * will call our sbp2_remove for us */
+ if (sbp2_login_device(lu) != 0) {
+ if (!hpsb_node_entry_valid(lu->ne))
+ return 0;
+
+ /* Maybe another initiator won the login. */
SBP2_ERR("Failed to reconnect to sbp2 device!");
return -EBUSY;
}
data = cpu_to_be32(SBP2_BUSY_TIMEOUT_VALUE);
if (hpsb_node_write(lu->ne, SBP2_BUSY_TIMEOUT_ADDRESS, &data, 4))
- SBP2_ERR("%s error", __FUNCTION__);
+ SBP2_ERR("%s error", __func__);
return 0;
}
static void sbp2_create_command_orb(struct sbp2_lu *lu,
struct sbp2_command_info *cmd,
- unchar *scsi_cmd,
- unsigned int scsi_use_sg,
- unsigned int scsi_request_bufflen,
- struct scatterlist *sg,
- enum dma_data_direction dma_dir)
+ struct scsi_cmnd *SCpnt)
{
struct sbp2_fwhost_info *hi = lu->hi;
struct sbp2_command_orb *orb = &cmd->command_orb;
u32 orb_direction;
+ unsigned int scsi_request_bufflen = scsi_bufflen(SCpnt);
+ enum dma_data_direction dma_dir = SCpnt->sc_data_direction;
/*
* Set-up our command ORB.
orb->data_descriptor_lo = 0x0;
orb->misc |= ORB_SET_DIRECTION(1);
} else
- sbp2_prep_command_orb_sg(orb, hi, cmd, scsi_use_sg, sg,
+ sbp2_prep_command_orb_sg(orb, hi, cmd, scsi_sg_count(SCpnt),
+ scsi_sglist(SCpnt),
orb_direction, dma_dir);
sbp2util_cpu_to_be32_buffer(orb, sizeof(*orb));
- memset(orb->cdb, 0, 12);
- memcpy(orb->cdb, scsi_cmd, COMMAND_SIZE(*scsi_cmd));
+ memset(orb->cdb, 0, sizeof(orb->cdb));
+ memcpy(orb->cdb, SCpnt->cmnd, SCpnt->cmd_len);
}
static void sbp2_link_orb_command(struct sbp2_lu *lu,
static int sbp2_send_command(struct sbp2_lu *lu, struct scsi_cmnd *SCpnt,
void (*done)(struct scsi_cmnd *))
{
- unchar *scsi_cmd = (unchar *)SCpnt->cmnd;
struct sbp2_command_info *cmd;
cmd = sbp2util_allocate_command_orb(lu, SCpnt, done);
if (!cmd)
return -EIO;
- sbp2_create_command_orb(lu, cmd, scsi_cmd, scsi_sg_count(SCpnt),
- scsi_bufflen(SCpnt), scsi_sglist(SCpnt),
- SCpnt->sc_data_direction);
+ sbp2_create_command_orb(lu, cmd, SCpnt);
sbp2_link_orb_command(lu, cmd);
return 0;
lu->sdev = sdev;
sdev->allow_restart = 1;
- /*
- * Update the dma alignment (minimum alignment requirements for
- * start and end of DMA transfers) to be a sector
- */
- blk_queue_update_dma_alignment(sdev->request_queue, 511);
+ /* SBP-2 requires quadlet alignment of the data buffers. */
+ blk_queue_update_dma_alignment(sdev->request_queue, 4 - 1);
if (lu->workarounds & SBP2_WORKAROUND_INQUIRY_36)
sdev->inquiry_len = 36;
sdev->use_10_for_rw = 1;
+ if (sbp2_exclusive_login)
+ sdev->manage_start_stop = 1;
if (sdev->type == TYPE_ROM)
sdev->use_10_for_ms = 1;
if (sdev->type == TYPE_DISK &&
sdev->skip_ms_page_8 = 1;
if (lu->workarounds & SBP2_WORKAROUND_FIX_CAPACITY)
sdev->fix_capacity = 1;
+ if (lu->workarounds & SBP2_WORKAROUND_POWER_CONDITION)
+ sdev->start_stop_pwr_cond = 1;
if (lu->workarounds & SBP2_WORKAROUND_128K_MAX_TRANS)
blk_queue_max_sectors(sdev->request_queue, 128 * 1024 / 512);
return 0;
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff