/**
* piix_set_pio_mode - set host controller for PIO mode
+ * @port: port
* @drive: drive
- * @pio: PIO mode number
*
* Set the interface PIO mode based upon the settings done by AMI BIOS.
*/
-static void piix_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void piix_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
{
- ide_hwif_t *hwif = drive->hwif;
struct pci_dev *dev = to_pci_dev(hwif->dev);
int is_slave = drive->dn & 1;
int master_port = hwif->channel ? 0x42 : 0x40;
u8 slave_data;
static DEFINE_SPINLOCK(tune_lock);
int control = 0;
+ const u8 pio = drive->pio_mode - XFER_PIO_0;
/* ISP RTC */
static const u8 timings[][2]= {
control |= 1; /* Programmable timing on */
if (drive->media == ide_disk)
control |= 4; /* Prefetch, post write */
- if (pio > 2)
+ if (ide_pio_need_iordy(drive, pio))
control |= 2; /* IORDY */
if (is_slave) {
master_data |= 0x4000;
/**
* piix_set_dma_mode - set host controller for DMA mode
+ * @hwif: port
* @drive: drive
- * @speed: DMA mode
*
* Set a PIIX host controller to the desired DMA mode. This involves
* programming the right timing data into the PCI configuration space.
*/
-static void piix_set_dma_mode(ide_drive_t *drive, const u8 speed)
+static void piix_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
{
- ide_hwif_t *hwif = drive->hwif;
struct pci_dev *dev = to_pci_dev(hwif->dev);
u8 maslave = hwif->channel ? 0x42 : 0x40;
int a_speed = 3 << (drive->dn * 4);
int sitre;
u16 reg4042, reg4a;
u8 reg48, reg54, reg55;
+ const u8 speed = drive->dma_mode;
pci_read_config_word(dev, maslave, ®4042);
sitre = (reg4042 & 0x4000) ? 1 : 0;
pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
} else {
const u8 mwdma_to_pio[] = { 0, 3, 4 };
- u8 pio;
if (reg48 & u_flag)
pci_write_config_byte(dev, 0x48, reg48 & ~u_flag);
pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
if (speed >= XFER_MW_DMA_0)
- pio = mwdma_to_pio[speed - XFER_MW_DMA_0];
+ drive->pio_mode =
+ mwdma_to_pio[speed - XFER_MW_DMA_0] + XFER_PIO_0;
else
- pio = 2; /* only SWDMA2 is allowed */
+ drive->pio_mode = XFER_PIO_2; /* for SWDMA2 */
- piix_set_pio_mode(drive, pio);
+ piix_set_pio_mode(hwif, drive);
}
}
* out to be nice and simple.
*/
-static unsigned int init_chipset_ich(struct pci_dev *dev)
+static int init_chipset_ich(struct pci_dev *dev)
{
u32 extra = 0;
{ 0x27DF, 0x103C, 0x30A1 }, /* ICH7 on HP Compaq nc2400 */
{ 0x27DF, 0x1071, 0xD221 }, /* ICH7 on Hercules EC-900 */
{ 0x24CA, 0x1025, 0x0061 }, /* ICH4 on Acer Aspire 2023WLMi */
+ { 0x24CA, 0x1025, 0x003d }, /* ICH4 on ACER TM290 */
+ { 0x266F, 0x1025, 0x0066 }, /* ICH6 on ACER Aspire 1694WLMi */
{ 0x2653, 0x1043, 0x82D8 }, /* ICH6M on Asus Eee 701 */
+ { 0x27df, 0x104d, 0x900e }, /* ICH7 on Sony TZ-90 */
/* end marker */
{ 0, }
};
.cable_detect = piix_cable_detect,
};
-#ifndef CONFIG_IA64
- #define IDE_HFLAGS_PIIX IDE_HFLAG_LEGACY_IRQS
-#else
- #define IDE_HFLAGS_PIIX 0
-#endif
-
#define DECLARE_PIIX_DEV(udma) \
{ \
.name = DRV_NAME, \
.init_hwif = init_hwif_piix, \
.enablebits = {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, \
.port_ops = &piix_port_ops, \
- .host_flags = IDE_HFLAGS_PIIX, \
.pio_mask = ATA_PIO4, \
.swdma_mask = ATA_SWDMA2_ONLY, \
.mwdma_mask = ATA_MWDMA12_ONLY, \
.init_hwif = init_hwif_piix, \
.enablebits = {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, \
.port_ops = &ich_port_ops, \
- .host_flags = IDE_HFLAGS_PIIX, \
.pio_mask = ATA_PIO4, \
.swdma_mask = ATA_SWDMA2_ONLY, \
.mwdma_mask = ATA_MWDMA12_ONLY, \
*/
.name = DRV_NAME,
.enablebits = {{0x6d,0xc0,0x80}, {0x6d,0xc0,0xc0}},
- .host_flags = IDE_HFLAG_ISA_PORTS | IDE_HFLAG_NO_DMA |
- IDE_HFLAGS_PIIX,
+ .host_flags = IDE_HFLAG_ISA_PORTS | IDE_HFLAG_NO_DMA,
.pio_mask = ATA_PIO4,
/* This is a painful system best to let it self tune for now */
},