/*
- * linux/drivers/ide/pci/piix.c Version 0.46 December 3, 2006
+ * linux/drivers/ide/pci/piix.c Version 0.52 Jul 14, 2007
*
* Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer
* Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
* Copyright (C) 2003 Red Hat Inc <alan@redhat.com>
- * Copyright (C) 2006 MontaVista Software, Inc. <source@mvista.com>
+ * Copyright (C) 2006-2007 MontaVista Software, Inc. <source@mvista.com>
*
* May be copied or modified under the terms of the GNU General Public License
*
* 41
* 43
*
- * | PIO 0 | c0 | 80 | 0 | piix_tune_drive(drive, 0);
- * | PIO 2 | SW2 | d0 | 90 | 4 | piix_tune_drive(drive, 2);
- * | PIO 3 | MW1 | e1 | a1 | 9 | piix_tune_drive(drive, 3);
- * | PIO 4 | MW2 | e3 | a3 | b | piix_tune_drive(drive, 4);
- *
+ * | PIO 0 | c0 | 80 | 0 |
+ * | PIO 2 | SW2 | d0 | 90 | 4 |
+ * | PIO 3 | MW1 | e1 | a1 | 9 |
+ * | PIO 4 | MW2 | e3 | a3 | b |
+ *
* sitre = word40 & 0x4000; primary
* sitre = word42 & 0x4000; secondary
*
static int no_piix_dma;
/**
- * piix_ratemask - compute rate mask for PIIX IDE
- * @drive: IDE drive to compute for
- *
- * Returns the available modes for the PIIX IDE controller.
- */
-
-static u8 piix_ratemask (ide_drive_t *drive)
-{
- struct pci_dev *dev = HWIF(drive)->pci_dev;
- u8 mode;
-
- switch(dev->device) {
- case PCI_DEVICE_ID_INTEL_82801EB_1:
- mode = 3;
- break;
- /* UDMA 100 capable */
- case PCI_DEVICE_ID_INTEL_82801BA_8:
- case PCI_DEVICE_ID_INTEL_82801BA_9:
- case PCI_DEVICE_ID_INTEL_82801CA_10:
- case PCI_DEVICE_ID_INTEL_82801CA_11:
- case PCI_DEVICE_ID_INTEL_82801E_11:
- case PCI_DEVICE_ID_INTEL_82801DB_1:
- case PCI_DEVICE_ID_INTEL_82801DB_10:
- case PCI_DEVICE_ID_INTEL_82801DB_11:
- case PCI_DEVICE_ID_INTEL_82801EB_11:
- case PCI_DEVICE_ID_INTEL_ESB_2:
- case PCI_DEVICE_ID_INTEL_ICH6_19:
- case PCI_DEVICE_ID_INTEL_ICH7_21:
- case PCI_DEVICE_ID_INTEL_ESB2_18:
- case PCI_DEVICE_ID_INTEL_ICH8_6:
- mode = 3;
- break;
- /* UDMA 66 capable */
- case PCI_DEVICE_ID_INTEL_82801AA_1:
- case PCI_DEVICE_ID_INTEL_82372FB_1:
- mode = 2;
- break;
- /* UDMA 33 capable */
- case PCI_DEVICE_ID_INTEL_82371AB:
- case PCI_DEVICE_ID_INTEL_82443MX_1:
- case PCI_DEVICE_ID_INTEL_82451NX:
- case PCI_DEVICE_ID_INTEL_82801AB_1:
- return 1;
- /* Non UDMA capable (MWDMA2) */
- case PCI_DEVICE_ID_INTEL_82371SB_1:
- case PCI_DEVICE_ID_INTEL_82371FB_1:
- case PCI_DEVICE_ID_INTEL_82371FB_0:
- case PCI_DEVICE_ID_INTEL_82371MX:
- default:
- return 0;
- }
-
- /*
- * If we are UDMA66 capable fall back to UDMA33
- * if the drive cannot see an 80pin cable.
- */
- if (!eighty_ninty_three(drive))
- mode = min_t(u8, mode, 1);
- return mode;
-}
-
-/**
- * piix_dma_2_pio - return the PIO mode matching DMA
- * @xfer_rate: transfer speed
+ * piix_set_pio_mode - set host controller for PIO mode
+ * @drive: drive
+ * @pio: PIO mode number
*
- * Returns the nearest equivalent PIO timing for the PIO or DMA
- * mode requested by the controller.
+ * Set the interface PIO mode based upon the settings done by AMI BIOS.
*/
-
-static u8 piix_dma_2_pio (u8 xfer_rate) {
- switch(xfer_rate) {
- case XFER_UDMA_6:
- case XFER_UDMA_5:
- case XFER_UDMA_4:
- case XFER_UDMA_3:
- case XFER_UDMA_2:
- case XFER_UDMA_1:
- case XFER_UDMA_0:
- case XFER_MW_DMA_2:
- case XFER_PIO_4:
- return 4;
- case XFER_MW_DMA_1:
- case XFER_PIO_3:
- return 3;
- case XFER_SW_DMA_2:
- case XFER_PIO_2:
- return 2;
- case XFER_MW_DMA_0:
- case XFER_SW_DMA_1:
- case XFER_SW_DMA_0:
- case XFER_PIO_1:
- case XFER_PIO_0:
- case XFER_PIO_SLOW:
- default:
- return 0;
- }
-}
-/**
- * piix_tune_drive - tune a drive attached to a PIIX
- * @drive: drive to tune
- * @pio: desired PIO mode
- *
- * Set the interface PIO mode based upon the settings done by AMI BIOS
- * (might be useful if drive is not registered in CMOS for any reason).
- */
-static void piix_tune_drive (ide_drive_t *drive, u8 pio)
+static void piix_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
{ 2, 1 },
{ 2, 3 }, };
- pio = ide_get_best_pio_mode(drive, pio, 4, NULL);
-
/*
* Master vs slave is synchronized above us but the slave register is
* shared by the two hwifs so the corner case of two slave timeouts in
master_data |= 0x4000;
master_data &= ~0x0070;
if (pio > 1) {
- /* enable PPE, IE and TIME */
- master_data = master_data | (control << 4);
+ /* Set PPE, IE and TIME */
+ master_data |= control << 4;
}
pci_read_config_byte(dev, slave_port, &slave_data);
- slave_data = slave_data & (hwif->channel ? 0x0f : 0xf0);
- slave_data = slave_data | (((timings[pio][0] << 2) | timings[pio][1]) << (hwif->channel ? 4 : 0));
+ slave_data &= hwif->channel ? 0x0f : 0xf0;
+ slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) <<
+ (hwif->channel ? 4 : 0);
} else {
master_data &= ~0x3307;
if (pio > 1) {
/* enable PPE, IE and TIME */
- master_data = master_data | control;
+ master_data |= control;
}
- master_data = master_data | (timings[pio][0] << 12) | (timings[pio][1] << 8);
+ master_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8);
}
pci_write_config_word(dev, master_port, master_data);
if (is_slave)
}
/**
- * piix_tune_chipset - tune a PIIX interface
- * @drive: IDE drive to tune
- * @xferspeed: speed to configure
+ * piix_set_dma_mode - set host controller for DMA mode
+ * @drive: drive
+ * @speed: DMA mode
*
- * Set a PIIX interface channel to the desired speeds. This involves
- * requires the right timing data into the PIIX configuration space
- * then setting the drive parameters appropriately
+ * Set a PIIX host controller to the desired DMA mode. This involves
+ * programming the right timing data into the PCI configuration space.
*/
-
-static int piix_tune_chipset (ide_drive_t *drive, u8 xferspeed)
+
+static void piix_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
u8 maslave = hwif->channel ? 0x42 : 0x40;
- u8 speed = ide_rate_filter(piix_ratemask(drive), xferspeed);
int a_speed = 3 << (drive->dn * 4);
int u_flag = 1 << drive->dn;
int v_flag = 0x01 << drive->dn;
int u_speed = 0;
int sitre;
u16 reg4042, reg4a;
- u8 reg48, reg54, reg55;
+ u8 reg48, reg54, reg55, pio;
pci_read_config_word(dev, maslave, ®4042);
sitre = (reg4042 & 0x4000) ? 1 : 0;
case XFER_MW_DMA_2:
case XFER_MW_DMA_1:
case XFER_SW_DMA_2: break;
- case XFER_PIO_4:
- case XFER_PIO_3:
- case XFER_PIO_2:
- case XFER_PIO_0: break;
- default: return -1;
+ default: return;
}
if (speed >= XFER_UDMA_0) {
pci_write_config_byte(dev, 0x54, reg54 | v_flag);
} else
pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
+
+ pio = 4;
} else {
+ const u8 mwdma_to_pio[] = { 0, 3, 4 };
+
if (reg48 & u_flag)
pci_write_config_byte(dev, 0x48, reg48 & ~u_flag);
if (reg4a & a_speed)
pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
if (reg55 & w_flag)
pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
- }
-
- piix_tune_drive(drive, piix_dma_2_pio(speed));
- return (ide_config_drive_speed(drive, speed));
-}
-
-/**
- * piix_config_drive_for_dma - configure drive for DMA
- * @drive: IDE drive to configure
- *
- * Set up a PIIX interface channel for the best available speed.
- * We prefer UDMA if it is available and then MWDMA. If DMA is
- * not available we switch to PIO and return 0.
- */
-
-static int piix_config_drive_for_dma (ide_drive_t *drive)
-{
- u8 speed = ide_dma_speed(drive, piix_ratemask(drive));
-
- /*
- * If no DMA speed was available or the chipset has DMA bugs
- * then disable DMA and use PIO
- */
- if (!speed || no_piix_dma)
- return 0;
-
- (void) piix_tune_chipset(drive, speed);
- return ide_dma_enable(drive);
-}
-
-/**
- * piix_config_drive_xfer_rate - set up an IDE device
- * @drive: IDE drive to configure
- *
- * Set up the PIIX interface for the best available speed on this
- * interface, preferring DMA to PIO.
- */
-
-static int piix_config_drive_xfer_rate (ide_drive_t *drive)
-{
- ide_hwif_t *hwif = HWIF(drive);
- struct hd_driveid *id = drive->id;
-
- drive->init_speed = 0;
-
- if ((id->capability & 1) && drive->autodma) {
-
- if (ide_use_dma(drive) && piix_config_drive_for_dma(drive))
- return hwif->ide_dma_on(drive);
- goto fast_ata_pio;
-
- } else if ((id->capability & 8) || (id->field_valid & 2)) {
-fast_ata_pio:
- /* Find best PIO mode. */
- (void) hwif->speedproc(drive, XFER_PIO_0 +
- ide_get_best_pio_mode(drive, 255, 4, NULL));
- return hwif->ide_dma_off_quietly(drive);
+ if (speed >= XFER_MW_DMA_0)
+ pio = mwdma_to_pio[speed - XFER_MW_DMA_0];
+ else
+ pio = 2; /* only SWDMA2 is allowed */
}
- /* IORDY not supported */
- return 0;
+
+ piix_set_pio_mode(drive, pio);
}
/**
hwif->OUTB(dma_stat, hwif->dma_status);
}
+struct ich_laptop {
+ u16 device;
+ u16 subvendor;
+ u16 subdevice;
+};
+
+/*
+ * List of laptops that use short cables rather than 80 wire
+ */
+
+static const struct ich_laptop ich_laptop[] = {
+ /* devid, subvendor, subdev */
+ { 0x27DF, 0x0005, 0x0280 }, /* ICH7 on Acer 5602WLMi */
+ { 0x27DF, 0x1025, 0x0110 }, /* ICH7 on Acer 3682WLMi */
+ { 0x27DF, 0x1043, 0x1267 }, /* ICH7 on Asus W5F */
+ { 0x24CA, 0x1025, 0x0061 }, /* ICH4 on Acer Aspire 2023WLMi */
+ /* end marker */
+ { 0, }
+};
+
+static u8 __devinit piix_cable_detect(ide_hwif_t *hwif)
+{
+ struct pci_dev *pdev = hwif->pci_dev;
+ const struct ich_laptop *lap = &ich_laptop[0];
+ u8 reg54h = 0, mask = hwif->channel ? 0xc0 : 0x30;
+
+ /* check for specials */
+ while (lap->device) {
+ if (lap->device == pdev->device &&
+ lap->subvendor == pdev->subsystem_vendor &&
+ lap->subdevice == pdev->subsystem_device) {
+ return ATA_CBL_PATA40_SHORT;
+ }
+ lap++;
+ }
+
+ pci_read_config_byte(pdev, 0x54, ®54h);
+
+ return (reg54h & mask) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
+}
+
/**
* init_hwif_piix - fill in the hwif for the PIIX
* @hwif: IDE interface
static void __devinit init_hwif_piix(ide_hwif_t *hwif)
{
- u8 reg54h = 0, reg55h = 0, ata66 = 0;
- u8 mask = hwif->channel ? 0xc0 : 0x30;
-
#ifndef CONFIG_IA64
if (!hwif->irq)
hwif->irq = hwif->channel ? 15 : 14;
}
hwif->autodma = 0;
- hwif->tuneproc = &piix_tune_drive;
- hwif->speedproc = &piix_tune_chipset;
+
+ hwif->set_pio_mode = &piix_set_pio_mode;
+ hwif->set_dma_mode = &piix_set_dma_mode;
+
hwif->drives[0].autotune = 1;
hwif->drives[1].autotune = 1;
hwif->ide_dma_clear_irq = &piix_dma_clear_irq;
hwif->atapi_dma = 1;
- hwif->ultra_mask = 0x3f;
+
+ hwif->ultra_mask = hwif->cds->udma_mask;
hwif->mwdma_mask = 0x06;
hwif->swdma_mask = 0x04;
- switch(hwif->pci_dev->device) {
- case PCI_DEVICE_ID_INTEL_82371MX:
- hwif->mwdma_mask = 0x80;
- hwif->swdma_mask = 0x80;
- case PCI_DEVICE_ID_INTEL_82371FB_0:
- case PCI_DEVICE_ID_INTEL_82371FB_1:
- case PCI_DEVICE_ID_INTEL_82371SB_1:
- hwif->ultra_mask = 0x80;
- break;
- case PCI_DEVICE_ID_INTEL_82371AB:
- case PCI_DEVICE_ID_INTEL_82443MX_1:
- case PCI_DEVICE_ID_INTEL_82451NX:
- case PCI_DEVICE_ID_INTEL_82801AB_1:
- hwif->ultra_mask = 0x07;
- break;
- default:
- pci_read_config_byte(hwif->pci_dev, 0x54, ®54h);
- pci_read_config_byte(hwif->pci_dev, 0x55, ®55h);
- ata66 = (reg54h & mask) ? 1 : 0;
- break;
+ if (hwif->ultra_mask & 0x78) {
+ if (hwif->cbl != ATA_CBL_PATA40_SHORT)
+ hwif->cbl = piix_cable_detect(hwif);
}
- if (!(hwif->udma_four))
- hwif->udma_four = ata66;
- hwif->ide_dma_check = &piix_config_drive_xfer_rate;
+ if (no_piix_dma)
+ hwif->ultra_mask = hwif->mwdma_mask = hwif->swdma_mask = 0;
+
if (!noautodma)
hwif->autodma = 1;
hwif->drives[0].autodma = hwif->autodma;
}
-#define DECLARE_PIIX_DEV(name_str) \
+#define DECLARE_PIIX_DEV(name_str, udma) \
{ \
.name = name_str, \
.init_chipset = init_chipset_piix, \
.init_hwif = init_hwif_piix, \
- .channels = 2, \
.autodma = AUTODMA, \
.enablebits = {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, \
.bootable = ON_BOARD, \
+ .pio_mask = ATA_PIO4, \
+ .udma_mask = udma, \
}
static ide_pci_device_t piix_pci_info[] __devinitdata = {
- /* 0 */ DECLARE_PIIX_DEV("PIIXa"),
- /* 1 */ DECLARE_PIIX_DEV("PIIXb"),
+ /* 0 */ DECLARE_PIIX_DEV("PIIXa", 0x00), /* no udma */
+ /* 1 */ DECLARE_PIIX_DEV("PIIXb", 0x00), /* no udma */
/* 2 */
{ /*
*/
.name = "MPIIX",
.init_hwif = init_hwif_piix,
- .channels = 2,
.autodma = NODMA,
.enablebits = {{0x6d,0xc0,0x80}, {0x6d,0xc0,0xc0}},
.bootable = ON_BOARD,
- .flags = IDEPCI_FLAG_ISA_PORTS
+ .host_flags = IDE_HFLAG_ISA_PORTS,
+ .pio_mask = ATA_PIO4,
},
- /* 3 */ DECLARE_PIIX_DEV("PIIX3"),
- /* 4 */ DECLARE_PIIX_DEV("PIIX4"),
- /* 5 */ DECLARE_PIIX_DEV("ICH0"),
- /* 6 */ DECLARE_PIIX_DEV("PIIX4"),
- /* 7 */ DECLARE_PIIX_DEV("ICH"),
- /* 8 */ DECLARE_PIIX_DEV("PIIX4"),
- /* 9 */ DECLARE_PIIX_DEV("PIIX4"),
- /* 10 */ DECLARE_PIIX_DEV("ICH2"),
- /* 11 */ DECLARE_PIIX_DEV("ICH2M"),
- /* 12 */ DECLARE_PIIX_DEV("ICH3M"),
- /* 13 */ DECLARE_PIIX_DEV("ICH3"),
- /* 14 */ DECLARE_PIIX_DEV("ICH4"),
- /* 15 */ DECLARE_PIIX_DEV("ICH5"),
- /* 16 */ DECLARE_PIIX_DEV("C-ICH"),
- /* 17 */ DECLARE_PIIX_DEV("ICH4"),
- /* 18 */ DECLARE_PIIX_DEV("ICH5-SATA"),
- /* 19 */ DECLARE_PIIX_DEV("ICH5"),
- /* 20 */ DECLARE_PIIX_DEV("ICH6"),
- /* 21 */ DECLARE_PIIX_DEV("ICH7"),
- /* 22 */ DECLARE_PIIX_DEV("ICH4"),
- /* 23 */ DECLARE_PIIX_DEV("ESB2"),
- /* 24 */ DECLARE_PIIX_DEV("ICH8M"),
+ /* 3 */ DECLARE_PIIX_DEV("PIIX3", 0x00), /* no udma */
+ /* 4 */ DECLARE_PIIX_DEV("PIIX4", 0x07), /* udma0-2 */
+ /* 5 */ DECLARE_PIIX_DEV("ICH0", 0x07), /* udma0-2 */
+ /* 6 */ DECLARE_PIIX_DEV("PIIX4", 0x07), /* udma0-2 */
+ /* 7 */ DECLARE_PIIX_DEV("ICH", 0x1f), /* udma0-4 */
+ /* 8 */ DECLARE_PIIX_DEV("PIIX4", 0x1f), /* udma0-4 */
+ /* 9 */ DECLARE_PIIX_DEV("PIIX4", 0x07), /* udma0-2 */
+ /* 10 */ DECLARE_PIIX_DEV("ICH2", 0x3f), /* udma0-5 */
+ /* 11 */ DECLARE_PIIX_DEV("ICH2M", 0x3f), /* udma0-5 */
+ /* 12 */ DECLARE_PIIX_DEV("ICH3M", 0x3f), /* udma0-5 */
+ /* 13 */ DECLARE_PIIX_DEV("ICH3", 0x3f), /* udma0-5 */
+ /* 14 */ DECLARE_PIIX_DEV("ICH4", 0x3f), /* udma0-5 */
+ /* 15 */ DECLARE_PIIX_DEV("ICH5", 0x3f), /* udma0-5 */
+ /* 16 */ DECLARE_PIIX_DEV("C-ICH", 0x3f), /* udma0-5 */
+ /* 17 */ DECLARE_PIIX_DEV("ICH4", 0x3f), /* udma0-5 */
+ /* 18 */ DECLARE_PIIX_DEV("ICH5-SATA", 0x3f), /* udma0-5 */
+ /* 19 */ DECLARE_PIIX_DEV("ICH5", 0x3f), /* udma0-5 */
+ /* 20 */ DECLARE_PIIX_DEV("ICH6", 0x3f), /* udma0-5 */
+ /* 21 */ DECLARE_PIIX_DEV("ICH7", 0x3f), /* udma0-5 */
+ /* 22 */ DECLARE_PIIX_DEV("ICH4", 0x3f), /* udma0-5 */
+ /* 23 */ DECLARE_PIIX_DEV("ESB2", 0x3f), /* udma0-5 */
+ /* 24 */ DECLARE_PIIX_DEV("ICH8M", 0x3f), /* udma0-5 */
};
/**
{
struct pci_dev *pdev = NULL;
u16 cfg;
- u8 rev;
while((pdev=pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, pdev))!=NULL)
{
/* Look for 450NX PXB. Check for problem configurations
A PCI quirk checks bit 6 already */
- pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
pci_read_config_word(pdev, 0x41, &cfg);
/* Only on the original revision: IDE DMA can hang */
- if(rev == 0x00)
+ if (pdev->revision == 0x00)
no_piix_dma = 1;
/* On all revisions below 5 PXB bus lock must be disabled for IDE */
- else if(cfg & (1<<14) && rev < 5)
+ else if (cfg & (1<<14) && pdev->revision < 5)
no_piix_dma = 2;
}
if(no_piix_dma)
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff